From 0c0436f47c296513dace43d3ba20e3cc36f8f527 Mon Sep 17 00:00:00 2001 From: Trygve Laugstøl Date: Sun, 25 Mar 2012 17:46:26 +0200 Subject: Board, rev A. --- firmware/LUFA/Drivers/USB/Class/Host/Printer.h | 282 +++++++++++++++++++++++++ 1 file changed, 282 insertions(+) create mode 100644 firmware/LUFA/Drivers/USB/Class/Host/Printer.h (limited to 'firmware/LUFA/Drivers/USB/Class/Host/Printer.h') diff --git a/firmware/LUFA/Drivers/USB/Class/Host/Printer.h b/firmware/LUFA/Drivers/USB/Class/Host/Printer.h new file mode 100644 index 0000000..cc77e96 --- /dev/null +++ b/firmware/LUFA/Drivers/USB/Class/Host/Printer.h @@ -0,0 +1,282 @@ +/* + LUFA Library + Copyright (C) Dean Camera, 2010. + + dean [at] fourwalledcubicle [dot] com + www.lufa-lib.org +*/ + +/* + Copyright 2010 Dean Camera (dean [at] fourwalledcubicle [dot] com) + + Permission to use, copy, modify, distribute, and sell this + software and its documentation for any purpose is hereby granted + without fee, provided that the above copyright notice appear in + all copies and that both that the copyright notice and this + permission notice and warranty disclaimer appear in supporting + documentation, and that the name of the author not be used in + advertising or publicity pertaining to distribution of the + software without specific, written prior permission. + + The author disclaim all warranties with regard to this + software, including all implied warranties of merchantability + and fitness. In no event shall the author be liable for any + special, indirect or consequential damages or any damages + whatsoever resulting from loss of use, data or profits, whether + in an action of contract, negligence or other tortious action, + arising out of or in connection with the use or performance of + this software. +*/ + +/** \file + * \brief Host mode driver for the library USB Printer Class driver. + * + * Host mode driver for the library USB Printer Class driver. + * + * \note This file should not be included directly. It is automatically included as needed by the USB module driver + * dispatch header located in LUFA/Drivers/USB.h. + */ + +/** \ingroup Group_USBClassPrinter + * @defgroup Group_USBClassPrinterHost Printer Class Host Mode Driver + * + * \section Sec_Dependencies Module Source Dependencies + * The following files must be built with any user project that uses this module: + * - LUFA/Drivers/USB/Class/Host/Printer.c (Makefile source module name: LUFA_SRC_USBCLASS) + * + * \section Module Description + * Host Mode USB Class driver framework interface, for the Printer USB Class driver. + * + * @{ + */ + +#ifndef __PRINTER_CLASS_HOST_H__ +#define __PRINTER_CLASS_HOST_H__ + + /* Includes: */ + #include "../../USB.h" + #include "../Common/Printer.h" + + /* Enable C linkage for C++ Compilers: */ + #if defined(__cplusplus) + extern "C" { + #endif + + /* Preprocessor Checks: */ + #if !defined(__INCLUDE_FROM_PRINTER_DRIVER) + #error Do not include this file directly. Include LUFA/Drivers/USB.h instead. + #endif + + #if defined(__INCLUDE_FROM_PRINTER_HOST_C) && defined(NO_STREAM_CALLBACKS) + #error The NO_STREAM_CALLBACKS compile time option cannot be used in projects using the library Class drivers. + #endif + + /* Public Interface - May be used in end-application: */ + /* Type Defines: */ + /** \brief Printer Class Host Mode Configuration and State Structure. + * + * Class state structure. An instance of this structure should be made within the user application, + * and passed to each of the Printer class driver functions as the PRNTInterfaceInfo parameter. This + * stores each Printer interface's configuration and state information. + */ + typedef struct + { + const struct + { + uint8_t DataINPipeNumber; /**< Pipe number of the Printer interface's IN data pipe. */ + bool DataINPipeDoubleBank; /**< Indicates if the Printer interface's IN data pipe should use double banking. */ + + uint8_t DataOUTPipeNumber; /**< Pipe number of the Printer interface's OUT data pipe. */ + bool DataOUTPipeDoubleBank; /**< Indicates if the Printer interface's OUT data pipe should use double banking. */ + } Config; /**< Config data for the USB class interface within the device. All elements in this section + * must be set or the interface will fail to enumerate and operate correctly. + */ + struct + { + bool IsActive; /**< Indicates if the current interface instance is connected to an attached device, valid + * after \ref PRNT_Host_ConfigurePipes() is called and the Host state machine is in the + * Configured state. + */ + uint8_t InterfaceNumber; /**< Interface index of the Printer interface within the attached device. */ + uint8_t AlternateSetting; /**< Alternate setting within the Printer Interface in the attached device. */ + + uint16_t DataINPipeSize; /**< Size in bytes of the Printer interface's IN data pipe. */ + uint16_t DataOUTPipeSize; /**< Size in bytes of the Printer interface's OUT data pipe. */ + } State; /**< State data for the USB class interface within the device. All elements in this section + * may be set to initial values, but may also be ignored to default to sane values when + * the interface is enumerated. + */ + } USB_ClassInfo_PRNT_Host_t; + + /* Enums: */ + enum PRNT_Host_EnumerationFailure_ErrorCodes_t + { + PRNT_ENUMERROR_NoError = 0, /**< Configuration Descriptor was processed successfully. */ + PRNT_ENUMERROR_InvalidConfigDescriptor = 1, /**< The device returned an invalid Configuration Descriptor. */ + PRNT_ENUMERROR_NoCompatibleInterfaceFound = 2, /**< A compatible Printer interface was not found in the device's Configuration Descriptor. */ + }; + + /* Function Prototypes: */ + /** General management task for a given Printer host class interface, required for the correct operation of + * the interface. This should be called frequently in the main program loop, before the master USB management task + * \ref USB_USBTask(). + * + * \param[in,out] PRNTInterfaceInfo Pointer to a structure containing a Printer Class host configuration and state. + */ + void PRNT_Host_USBTask(USB_ClassInfo_PRNT_Host_t* const PRNTInterfaceInfo) ATTR_NON_NULL_PTR_ARG(1); + + /** Host interface configuration routine, to configure a given Printer host interface instance using the + * Configuration Descriptor read from an attached USB device. This function automatically updates the given Printer + * instance's state values and configures the pipes required to communicate with the interface if it is found within + * the device. This should be called once after the stack has enumerated the attached device, while the host state + * machine is in the Addressed state. + * + * \note The pipe index numbers as given in the interface's configuration structure must not overlap with any other + * interface, or pipe bank corruption will occur. Gaps in the allocated pipe numbers or non-sequential indexes + * within a single interface is allowed, but no two interfaces of any type have have interleaved pipe indexes. + * + * \param[in,out] PRNTInterfaceInfo Pointer to a structure containing a Printer Class host configuration and state. + * \param[in] ConfigDescriptorSize Length of the attached device's Configuration Descriptor. + * \param[in] DeviceConfigDescriptor Pointer to a buffer containing the attached device's Configuration Descriptor. + * + * \return A value from the \ref PRNT_Host_EnumerationFailure_ErrorCodes_t enum. + */ + uint8_t PRNT_Host_ConfigurePipes(USB_ClassInfo_PRNT_Host_t* const PRNTInterfaceInfo, + uint16_t ConfigDescriptorSize, + void* DeviceConfigDescriptor) ATTR_NON_NULL_PTR_ARG(1) ATTR_NON_NULL_PTR_ARG(3); + + /** Configures the printer to enable Bidirectional mode, if it is not already in this mode. This should be called + * once the connected device's configuration has been set, to ensure the printer is ready to accept commands. + * + * \param[in,out] PRNTInterfaceInfo Pointer to a structure containing a Printer Class host configuration and state. + * + * \return A value from the \ref USB_Host_SendControlErrorCodes_t enum. + */ + uint8_t PRNT_Host_SetBidirectionalMode(USB_ClassInfo_PRNT_Host_t* const PRNTInterfaceInfo) ATTR_NON_NULL_PTR_ARG(1); + + /** Retrieves the status of the virtual Printer port's inbound status lines. The result can then be masked against the + * PRNT_PORTSTATUS_* macros to determine the printer port's status. + * + * \param[in,out] PRNTInterfaceInfo Pointer to a structure containing a Printer Class host configuration and state. + * \param[out] PortStatus Location where the retrieved port status should be stored. + * + * \return A value from the \ref USB_Host_SendControlErrorCodes_t enum. + */ + uint8_t PRNT_Host_GetPortStatus(USB_ClassInfo_PRNT_Host_t* const PRNTInterfaceInfo, + uint8_t* const PortStatus) + ATTR_NON_NULL_PTR_ARG(1) ATTR_NON_NULL_PTR_ARG(2); + + /** Soft-resets the attached printer, readying it for new commands. + * + * \param[in,out] PRNTInterfaceInfo Pointer to a structure containing a Printer Class host configuration and state. + * + * \return A value from the \ref USB_Host_SendControlErrorCodes_t enum. + */ + uint8_t PRNT_Host_SoftReset(USB_ClassInfo_PRNT_Host_t* const PRNTInterfaceInfo) ATTR_NON_NULL_PTR_ARG(1); + + /** Flushes any data waiting to be sent, ensuring that the send buffer is cleared. + * + * \pre This function must only be called when the Host state machine is in the \ref HOST_STATE_Configured state or the + * call will fail. + * + * \param[in,out] PRNTInterfaceInfo Pointer to a structure containing a Printer Class host configuration and state. + * + * \return A value from the \ref Pipe_WaitUntilReady_ErrorCodes_t enum. + */ + uint8_t PRNT_Host_Flush(USB_ClassInfo_PRNT_Host_t* const PRNTInterfaceInfo) ATTR_NON_NULL_PTR_ARG(1); + + /** Sends the given raw data stream to the attached printer's input endpoint. This should contain commands that the + * printer is able to understand - for example, PCL data. Not all printers accept all printer languages; see + * \ref PRNT_Host_GetDeviceID() for details on determining acceptable languages for an attached printer. + * + * \pre This function must only be called when the Host state machine is in the \ref HOST_STATE_Configured state or the + * call will fail. + * + * \param[in,out] PRNTInterfaceInfo Pointer to a structure containing a Printer Class host configuration and state. + * \param[in] Buffer Pointer to a buffer containing the raw command stream to send to the printer. + * \param[in] Length Size in bytes of the command stream to be sent. + * + * \return A value from the \ref Pipe_Stream_RW_ErrorCodes_t enum. + */ + uint8_t PRNT_Host_SendString(USB_ClassInfo_PRNT_Host_t* const PRNTInterfaceInfo, + void* Buffer, + const uint16_t Length) ATTR_NON_NULL_PTR_ARG(1) ATTR_NON_NULL_PTR_ARG(2); + + /** Sends a given byte to the attached USB device, if connected. If a device is not connected when the function is called, the + * byte is discarded. Bytes will be queued for transmission to the device until either the pipe bank becomes full, or the + * \ref PRNT_Host_Flush() function is called to flush the pending data to the host. This allows for multiple bytes to be + * packed into a single pipe packet, increasing data throughput. + * + * \pre This function must only be called when the Host state machine is in the \ref HOST_STATE_Configured state or the + * call will fail. + * + * \param[in,out] PRNTInterfaceInfo Pointer to a structure containing a Printer Class host configuration and state. + * \param[in] Data Byte of data to send to the device. + * + * \return A value from the \ref Pipe_WaitUntilReady_ErrorCodes_t enum. + */ + uint8_t PRNT_Host_SendByte(USB_ClassInfo_PRNT_Host_t* const PRNTInterfaceInfo, + const uint8_t Data) ATTR_NON_NULL_PTR_ARG(1); + + /** Determines the number of bytes received by the printer interface from the device, waiting to be read. This indicates the number + * of bytes in the IN pipe bank only, and thus the number of calls to \ref PRNT_Host_ReceiveByte() which are guaranteed to succeed + * immediately. If multiple bytes are to be received, they should be buffered by the user application, as the pipe bank will not be + * released back to the USB controller until all bytes are read. + * + * \pre This function must only be called when the Host state machine is in the \ref HOST_STATE_Configured state or the + * call will fail. + * + * \param[in,out] PRNTInterfaceInfo Pointer to a structure containing a Printer Class host configuration and state. + * + * \return Total number of buffered bytes received from the device. + */ + uint16_t PRNT_Host_BytesReceived(USB_ClassInfo_PRNT_Host_t* const PRNTInterfaceInfo); + + /** Reads a byte of data from the device. If no data is waiting to be read of if a USB device is not connected, the function + * returns a negative value. The \ref PRNT_Host_BytesReceived() function may be queried in advance to determine how many bytes + * are currently buffered in the Printer interface's data receive pipe. + * + * \pre This function must only be called when the Host state machine is in the \ref HOST_STATE_Configured state or the + * call will fail. + * + * \param[in,out] PRNTInterfaceInfo Pointer to a structure containing a Printer Class host configuration and state. + * + * \return Next received byte from the device, or a negative value if no data received. + */ + int16_t PRNT_Host_ReceiveByte(USB_ClassInfo_PRNT_Host_t* const PRNTInterfaceInfo); + + /** Retrieves the attached printer device's ID string, formatted according to IEEE 1284. This string is sent as a + * Unicode string from the device and is automatically converted to an ASCII encoded C string by this function, thus + * the maximum reportable string length is two less than the size given (to accommodate the Unicode string length + * bytes which are removed). + * + * This string, when supported, contains the model, manufacturer and acceptable printer languages for the attached device. + * + * \param[in,out] PRNTInterfaceInfo Pointer to a structure containing a Printer Class host configuration and state. + * \param[out] DeviceIDString Pointer to a buffer where the Device ID string should be stored, in ASCII format. + * \param[in] BufferSize Size in bytes of the buffer allocated for the Device ID string. + * + * \return A value from the \ref Pipe_Stream_RW_ErrorCodes_t enum. + */ + uint8_t PRNT_Host_GetDeviceID(USB_ClassInfo_PRNT_Host_t* const PRNTInterfaceInfo, + char* const DeviceIDString, + const uint16_t BufferSize) ATTR_NON_NULL_PTR_ARG(1) ATTR_NON_NULL_PTR_ARG(2); + + /* Private Interface - For use in library only: */ + #if !defined(__DOXYGEN__) + /* Function Prototypes: */ + #if defined(__INCLUDE_FROM_PRINTER_HOST_C) + static uint8_t DCOMP_PRNT_Host_NextPRNTInterface(void* const CurrentDescriptor) ATTR_NON_NULL_PTR_ARG(1); + static uint8_t DCOMP_PRNT_Host_NextPRNTInterfaceEndpoint(void* const CurrentDescriptor) ATTR_NON_NULL_PTR_ARG(1); + #endif + #endif + + /* Disable C linkage for C++ Compilers: */ + #if defined(__cplusplus) + } + #endif + +#endif + +/** @} */ + -- cgit v1.2.3