From bf403680d72e360c7382f540ea25cfdcbe77b4e5 Mon Sep 17 00:00:00 2001 From: Darren Hart Date: Tue, 1 May 2012 21:14:18 -0700 Subject: initrdscripts: Update install.sh to work with mmc devices Fixes [YOCTO #2385] The installer only searches for hd[ab] sd[ab]. Some newer BSPs have mmcblk devices that should be used as the install target. These devices also have a partition prefix (mmcblk0p1 instead of mmcblk01). As they are detected asynchronously, it is necessary to add the rootwait kernel parameter to avoid a race condition trying to mount the root device. As BSPs like the FRI2 and the sys940x have mmc devices and will have a 1.2 release, we should push this to 1.2.1. The changes are perfectly contained and easily verified. Test for an mmcblk device and add the p partition prefix if necessary. Add the rootwait kernel parameter when an mmcblk device is detected. Replace the series of explicit umount commands with a single umount using a wildcard. This will find all the partitions and will not try to unmount non-existant devices. Avoid copy and paste errors by replacing /dev/${device}${pX} references with the previously assigned rootfs, bootfs, and swap variables. These changes have been tested on the FRI2 Sato image which installed to /dev/mmcblk0 as well as the N450 Sato image which installed to /dev/sda. Both were successful. Signed-off-by: Darren Hart CC: Scott Garman Signed-off-by: Richard Purdie --- .../initrdscripts/files/init-install.sh | 45 ++++++++++++---------- .../initrdscripts/initramfs-live-install_1.0.bb | 2 +- 2 files changed, 25 insertions(+), 22 deletions(-) (limited to 'meta/recipes-core') diff --git a/meta/recipes-core/initrdscripts/files/init-install.sh b/meta/recipes-core/initrdscripts/files/init-install.sh index 90978dd36..01ff82926 100644 --- a/meta/recipes-core/initrdscripts/files/init-install.sh +++ b/meta/recipes-core/initrdscripts/files/init-install.sh @@ -16,7 +16,7 @@ swap_ratio=5 found="no" echo "Searching for a hard drive..." -for device in 'hda' 'hdb' 'sda' 'sdb' +for device in 'hda' 'hdb' 'sda' 'sdb' 'mmcblk0' 'mmcblk1' do if [ -e /sys/block/${device}/removable ]; then if [ "$(cat /sys/block/${device}/removable)" = "0" ]; then @@ -62,13 +62,7 @@ rm -f /etc/udev/scripts/mount* # # Unmount anything the automounter had mounted # -umount /dev/${device} 2> /dev/null || /bin/true -umount /dev/${device}1 2> /dev/null || /bin/true -umount /dev/${device}2 2> /dev/null || /bin/true -umount /dev/${device}3 2> /dev/null || /bin/true -umount /dev/${device}4 2> /dev/null || /bin/true -umount /dev/${device}5 2> /dev/null || /bin/true -umount /dev/${device}6 2> /dev/null || /bin/true +umount /dev/${device}* 2> /dev/null || /bin/true if [ ! -b /dev/sda ] ; then mknod /dev/sda b 8 0 @@ -94,14 +88,23 @@ rootfs_start=$((boot_size + 1)) rootfs_end=$((rootfs_start+rootfs_size)) swap_start=$((rootfs_end+1)) -bootfs=/dev/${device}1 -rootfs=/dev/${device}2 -swap=/dev/${device}3 +# MMC devices are special in a couple of ways +# 1) they use a partition prefix character 'p' +# 2) they are detected asynchronously (need rootwait) +rootwait="" +part_prefix="" +if [ ! "${device#mmcblk}" = "${device}" ]; then + part_prefix="p" + rootwait="rootwait" +fi +bootfs=/dev/${device}${part_prefix}1 +rootfs=/dev/${device}${part_prefix}2 +swap=/dev/${device}${part_prefix}3 echo "*****************" -echo "Boot partition size: $boot_size MB (/dev/${device}1)" -echo "Rootfs partition size: $rootfs_size MB (/dev/${device}2)" -echo "Swap partition size: $swap_size MB (/dev/${device}3)" +echo "Boot partition size: $boot_size MB ($bootfs)" +echo "Rootfs partition size: $rootfs_size MB ($rootfs)" +echo "Swap partition size: $swap_size MB ($swap)" echo "*****************" echo "Deleting partition table on /dev/${device} ..." dd if=/dev/zero of=/dev/${device} bs=512 count=2 @@ -109,24 +112,24 @@ dd if=/dev/zero of=/dev/${device} bs=512 count=2 echo "Creating new partition table on /dev/${device} ..." parted /dev/${device} mklabel msdos -echo "Creating boot partition on /dev/${device}1" +echo "Creating boot partition on $bootfs" parted /dev/${device} mkpart primary 1 $boot_size -echo "Creating rootfs partition on /dev/${device}2" +echo "Creating rootfs partition on $rootfs" parted /dev/${device} mkpart primary $rootfs_start $rootfs_end -echo "Creating swap partition on /dev/${device}3" +echo "Creating swap partition on $swap" parted /dev/${device} mkpart primary $swap_start $disk_size parted /dev/${device} print -echo "Formatting /dev/${device}1 to ext2..." +echo "Formatting $bootfs to ext2..." mkfs.ext3 $bootfs -echo "Formatting /dev/${device}2 to ext3..." +echo "Formatting $rootfs to ext3..." mkfs.ext3 $rootfs -echo "Formatting swap partition...(/dev/${device}3)" +echo "Formatting swap partition...($swap)" mkswap $swap mkdir /ssd @@ -150,7 +153,7 @@ fi if [ -f /ssd/etc/grub.d/40_custom ] ; then echo "Preparing custom grub2 menu..." - sed -i "s@__ROOTFS__@$rootfs@g" /ssd/etc/grub.d/40_custom + sed -i "s@__ROOTFS__@$rootfs $rootwait@g" /ssd/etc/grub.d/40_custom sed -i "s/__VIDEO_MODE__/$3/g" /ssd/etc/grub.d/40_custom sed -i "s/__VGA_MODE__/$4/g" /ssd/etc/grub.d/40_custom mount $bootfs /bootmnt diff --git a/meta/recipes-core/initrdscripts/initramfs-live-install_1.0.bb b/meta/recipes-core/initrdscripts/initramfs-live-install_1.0.bb index 793a4b799..ac73ef80a 100644 --- a/meta/recipes-core/initrdscripts/initramfs-live-install_1.0.bb +++ b/meta/recipes-core/initrdscripts/initramfs-live-install_1.0.bb @@ -3,7 +3,7 @@ LICENSE = "MIT" LIC_FILES_CHKSUM = "file://${COREBASE}/meta/COPYING.MIT;md5=3da9cfbcb788c80a0384361b4de20420" SRC_URI = "file://init-install.sh" -PR = "r6" +PR = "r7" RDEPENDS_${PN} = "grub parted e2fsprogs-mke2fs" -- cgit v1.2.3