diff options
| -rw-r--r-- | fiken_status_panel.ino | 29 |
1 files changed, 13 insertions, 16 deletions
diff --git a/fiken_status_panel.ino b/fiken_status_panel.ino index 9f2126b..22f7f4a 100644 --- a/fiken_status_panel.ino +++ b/fiken_status_panel.ino @@ -66,10 +66,8 @@ void setup() { aci_state.aci_pins.miso_pin = MISO; aci_state.aci_pins.sck_pin = SCK; - /* - * SPI_CLOCK_DIV8 = 2MHz SPI speed - * SPI_CLOCK_DIV16 = 1MHz SPI speed - */ + // SPI_CLOCK_DIV8 = 2MHz SPI speed + // SPI_CLOCK_DIV16 = 1MHz SPI speed aci_state.aci_pins.spi_clock_divider = SPI_CLOCK_DIV8; aci_state.aci_pins.reset_pin = UNUSED; //4 for Nordic board, UNUSED for REDBEARLAB_SHIELD_V1_1 aci_state.aci_pins.active_pin = UNUSED; @@ -78,10 +76,10 @@ void setup() { aci_state.aci_pins.interface_is_interrupt = false; //Interrupts still not available in Chipkit aci_state.aci_pins.interrupt_number = 4; - //We reset the nRF8001 here by toggling the RESET line connected to the nRF8001 - //If the RESET line is not available we call the ACI Radio Reset to soft reset the nRF8001 - //then we initialize the data structures required to setup the nRF8001 - //The second parameter is for turning debug printing on for the ACI Commands and Events so they be printed on the Serial + // We reset the nRF8001 here by toggling the RESET line connected to the nRF8001 + // If the RESET line is not available we call the ACI Radio Reset to soft reset the nRF8001 + // then we initialize the data structures required to setup the nRF8001 + // The second parameter is for turning debug printing on for the ACI Commands and Events so they be printed on the Serial lib_aci_init(&aci_state, false); Serial.println(F("lib_aci_init done")); } @@ -106,10 +104,8 @@ static void aci_loop() { case ACI_DEVICE_STANDBY: Serial.println(F("ACI_DEVICE_STANDBY")); - //Looking for an iPhone by sending radio advertisements - //When an iPhone connects to us we will get an ACI_EVT_CONNECTED event from the nRF8001 if (aci_evt->params.device_started.hw_error) { - delay(20); //Magic number used to make sure the HW error event is handled correctly. + delay(20); // Magic number used to make sure the HW error event is handled correctly. } else { lib_aci_connect(180/* in seconds */, 0x0050 /* advertising interval 50ms*/); @@ -119,7 +115,7 @@ static void aci_loop() { case ACI_DEVICE_INVALID: case ACI_DEVICE_TEST: case ACI_DEVICE_SLEEP: - // ignored + // Ignored break; } break; @@ -154,7 +150,8 @@ static void aci_loop() { timing_change_done = false; aci_state.data_credit_available = aci_state.data_credit_total; - // Get the device version of the nRF8001 and store it in the Hardware Revision String + // Get the device version of the nRF8001 and store it in the Hardware Revision String. + // This will trigger a ACI_CMD_GET_DEVICE_VERSION. lib_aci_device_version(); break; @@ -197,9 +194,9 @@ static void aci_loop() { Serial.print(F(" Pipe Error Code: 0x")); Serial.println(aci_evt->params.pipe_error.error_code, HEX); - //Increment the credit available as the data packet was not sent. - //The pipe error also represents the Attribute protocol Error Response sent from the peer and that should not be counted - //for the credit. + // Increment the credit available as the data packet was not sent. + // The pipe error also represents the Attribute protocol Error Response sent from the peer and that should not be counted + // for the credit. if (ACI_STATUS_ERROR_PEER_ATT_ERROR != aci_evt->params.pipe_error.error_code) { aci_state.data_credit_available++; |