From afbb4cc73c44b6321cae39dbe46b97155805097d Mon Sep 17 00:00:00 2001 From: Trygve Laugstøl Date: Sun, 13 Dec 2015 21:03:11 +0100 Subject: wip --- .../DMA/ADC_TIM1/main.c | 212 ++++ .../DMA/ADC_TIM1/readme.txt | 107 ++ .../DMA/ADC_TIM1/stm32f10x_conf.h | 77 ++ .../DMA/ADC_TIM1/stm32f10x_it.c | 169 +++ .../DMA/ADC_TIM1/stm32f10x_it.h | 46 + .../DMA/ADC_TIM1/system_stm32f10x.c | 1094 ++++++++++++++++++++ .../DMA/Complete list of DMA examples.txt | 61 ++ .../DMA/FLASH_RAM/main.c | 206 ++++ .../DMA/FLASH_RAM/readme.txt | 87 ++ .../DMA/FLASH_RAM/stm32f10x_conf.h | 78 ++ .../DMA/FLASH_RAM/stm32f10x_it.c | 190 ++++ .../DMA/FLASH_RAM/stm32f10x_it.h | 47 + .../DMA/FLASH_RAM/system_stm32f10x.c | 1094 ++++++++++++++++++++ .../STM32F10x_StdPeriph_Examples/DMA/FSMC/main.c | 218 ++++ .../DMA/FSMC/readme.txt | 92 ++ .../DMA/FSMC/stm32f10x_conf.h | 77 ++ .../DMA/FSMC/stm32f10x_it.c | 167 +++ .../DMA/FSMC/stm32f10x_it.h | 46 + .../DMA/FSMC/system_stm32f10x.c | 1094 ++++++++++++++++++++ .../DMA/I2C_RAM/main.c | 256 +++++ .../DMA/I2C_RAM/readme.txt | 103 ++ .../DMA/I2C_RAM/stm32f10x_conf.h | 77 ++ .../DMA/I2C_RAM/stm32f10x_it.c | 167 +++ .../DMA/I2C_RAM/stm32f10x_it.h | 46 + .../DMA/I2C_RAM/system_stm32f10x.c | 1094 ++++++++++++++++++++ .../DMA/SPI_RAM/main.c | 358 +++++++ .../DMA/SPI_RAM/platform_config.h | 110 ++ .../DMA/SPI_RAM/readme.txt | 121 +++ .../DMA/SPI_RAM/stm32f10x_conf.h | 77 ++ .../DMA/SPI_RAM/stm32f10x_it.c | 167 +++ .../DMA/SPI_RAM/stm32f10x_it.h | 46 + .../DMA/SPI_RAM/system_stm32f10x.c | 1094 ++++++++++++++++++++ 32 files changed, 8878 insertions(+) create mode 100644 tmp/STM32F10x_StdPeriph_Lib_V3.5.0/Project/STM32F10x_StdPeriph_Examples/DMA/ADC_TIM1/main.c create mode 100644 tmp/STM32F10x_StdPeriph_Lib_V3.5.0/Project/STM32F10x_StdPeriph_Examples/DMA/ADC_TIM1/readme.txt create mode 100644 tmp/STM32F10x_StdPeriph_Lib_V3.5.0/Project/STM32F10x_StdPeriph_Examples/DMA/ADC_TIM1/stm32f10x_conf.h create mode 100644 tmp/STM32F10x_StdPeriph_Lib_V3.5.0/Project/STM32F10x_StdPeriph_Examples/DMA/ADC_TIM1/stm32f10x_it.c create mode 100644 tmp/STM32F10x_StdPeriph_Lib_V3.5.0/Project/STM32F10x_StdPeriph_Examples/DMA/ADC_TIM1/stm32f10x_it.h create mode 100644 tmp/STM32F10x_StdPeriph_Lib_V3.5.0/Project/STM32F10x_StdPeriph_Examples/DMA/ADC_TIM1/system_stm32f10x.c create mode 100644 tmp/STM32F10x_StdPeriph_Lib_V3.5.0/Project/STM32F10x_StdPeriph_Examples/DMA/Complete list of DMA examples.txt create mode 100644 tmp/STM32F10x_StdPeriph_Lib_V3.5.0/Project/STM32F10x_StdPeriph_Examples/DMA/FLASH_RAM/main.c create mode 100644 tmp/STM32F10x_StdPeriph_Lib_V3.5.0/Project/STM32F10x_StdPeriph_Examples/DMA/FLASH_RAM/readme.txt create mode 100644 tmp/STM32F10x_StdPeriph_Lib_V3.5.0/Project/STM32F10x_StdPeriph_Examples/DMA/FLASH_RAM/stm32f10x_conf.h create mode 100644 tmp/STM32F10x_StdPeriph_Lib_V3.5.0/Project/STM32F10x_StdPeriph_Examples/DMA/FLASH_RAM/stm32f10x_it.c create mode 100644 tmp/STM32F10x_StdPeriph_Lib_V3.5.0/Project/STM32F10x_StdPeriph_Examples/DMA/FLASH_RAM/stm32f10x_it.h create mode 100644 tmp/STM32F10x_StdPeriph_Lib_V3.5.0/Project/STM32F10x_StdPeriph_Examples/DMA/FLASH_RAM/system_stm32f10x.c create mode 100644 tmp/STM32F10x_StdPeriph_Lib_V3.5.0/Project/STM32F10x_StdPeriph_Examples/DMA/FSMC/main.c create mode 100644 tmp/STM32F10x_StdPeriph_Lib_V3.5.0/Project/STM32F10x_StdPeriph_Examples/DMA/FSMC/readme.txt create mode 100644 tmp/STM32F10x_StdPeriph_Lib_V3.5.0/Project/STM32F10x_StdPeriph_Examples/DMA/FSMC/stm32f10x_conf.h create mode 100644 tmp/STM32F10x_StdPeriph_Lib_V3.5.0/Project/STM32F10x_StdPeriph_Examples/DMA/FSMC/stm32f10x_it.c create mode 100644 tmp/STM32F10x_StdPeriph_Lib_V3.5.0/Project/STM32F10x_StdPeriph_Examples/DMA/FSMC/stm32f10x_it.h create mode 100644 tmp/STM32F10x_StdPeriph_Lib_V3.5.0/Project/STM32F10x_StdPeriph_Examples/DMA/FSMC/system_stm32f10x.c create mode 100644 tmp/STM32F10x_StdPeriph_Lib_V3.5.0/Project/STM32F10x_StdPeriph_Examples/DMA/I2C_RAM/main.c create mode 100644 tmp/STM32F10x_StdPeriph_Lib_V3.5.0/Project/STM32F10x_StdPeriph_Examples/DMA/I2C_RAM/readme.txt create mode 100644 tmp/STM32F10x_StdPeriph_Lib_V3.5.0/Project/STM32F10x_StdPeriph_Examples/DMA/I2C_RAM/stm32f10x_conf.h create mode 100644 tmp/STM32F10x_StdPeriph_Lib_V3.5.0/Project/STM32F10x_StdPeriph_Examples/DMA/I2C_RAM/stm32f10x_it.c create mode 100644 tmp/STM32F10x_StdPeriph_Lib_V3.5.0/Project/STM32F10x_StdPeriph_Examples/DMA/I2C_RAM/stm32f10x_it.h create mode 100644 tmp/STM32F10x_StdPeriph_Lib_V3.5.0/Project/STM32F10x_StdPeriph_Examples/DMA/I2C_RAM/system_stm32f10x.c create mode 100644 tmp/STM32F10x_StdPeriph_Lib_V3.5.0/Project/STM32F10x_StdPeriph_Examples/DMA/SPI_RAM/main.c create mode 100644 tmp/STM32F10x_StdPeriph_Lib_V3.5.0/Project/STM32F10x_StdPeriph_Examples/DMA/SPI_RAM/platform_config.h create mode 100644 tmp/STM32F10x_StdPeriph_Lib_V3.5.0/Project/STM32F10x_StdPeriph_Examples/DMA/SPI_RAM/readme.txt create mode 100644 tmp/STM32F10x_StdPeriph_Lib_V3.5.0/Project/STM32F10x_StdPeriph_Examples/DMA/SPI_RAM/stm32f10x_conf.h create mode 100644 tmp/STM32F10x_StdPeriph_Lib_V3.5.0/Project/STM32F10x_StdPeriph_Examples/DMA/SPI_RAM/stm32f10x_it.c create mode 100644 tmp/STM32F10x_StdPeriph_Lib_V3.5.0/Project/STM32F10x_StdPeriph_Examples/DMA/SPI_RAM/stm32f10x_it.h create mode 100644 tmp/STM32F10x_StdPeriph_Lib_V3.5.0/Project/STM32F10x_StdPeriph_Examples/DMA/SPI_RAM/system_stm32f10x.c (limited to 'tmp/STM32F10x_StdPeriph_Lib_V3.5.0/Project/STM32F10x_StdPeriph_Examples/DMA') diff --git a/tmp/STM32F10x_StdPeriph_Lib_V3.5.0/Project/STM32F10x_StdPeriph_Examples/DMA/ADC_TIM1/main.c b/tmp/STM32F10x_StdPeriph_Lib_V3.5.0/Project/STM32F10x_StdPeriph_Examples/DMA/ADC_TIM1/main.c new file mode 100644 index 0000000..fbf4cbf --- /dev/null +++ b/tmp/STM32F10x_StdPeriph_Lib_V3.5.0/Project/STM32F10x_StdPeriph_Examples/DMA/ADC_TIM1/main.c @@ -0,0 +1,212 @@ +/** + ****************************************************************************** + * @file DMA/ADC_TIM1/main.c + * @author MCD Application Team + * @version V3.5.0 + * @date 08-April-2011 + * @brief Main program body + ****************************************************************************** + * @attention + * + * THE PRESENT FIRMWARE WHICH IS FOR GUIDANCE ONLY AIMS AT PROVIDING CUSTOMERS + * WITH CODING INFORMATION REGARDING THEIR PRODUCTS IN ORDER FOR THEM TO SAVE + * TIME. AS A RESULT, STMICROELECTRONICS SHALL NOT BE HELD LIABLE FOR ANY + * DIRECT, INDIRECT OR CONSEQUENTIAL DAMAGES WITH RESPECT TO ANY CLAIMS ARISING + * FROM THE CONTENT OF SUCH FIRMWARE AND/OR THE USE MADE BY CUSTOMERS OF THE + * CODING INFORMATION CONTAINED HEREIN IN CONNECTION WITH THEIR PRODUCTS. + * + *

© COPYRIGHT 2011 STMicroelectronics

+ ****************************************************************************** + */ + +/* Includes ------------------------------------------------------------------*/ +#include "stm32f10x.h" + +/** @addtogroup STM32F10x_StdPeriph_Examples + * @{ + */ + +/** @addtogroup DMA_ADC_TIM1 + * @{ + */ + +/* Private typedef -----------------------------------------------------------*/ +/* Private define ------------------------------------------------------------*/ +#define ADC1_DR_Address 0x4001244C +#define TIM1_CCR1_Address 0x40012C34 + +/* Private macro -------------------------------------------------------------*/ +/* Private variables ---------------------------------------------------------*/ +ADC_InitTypeDef ADC_InitStructure; +TIM_TimeBaseInitTypeDef TIM_TimeBaseStructure; +TIM_OCInitTypeDef TIM_OCInitStructure; +DMA_InitTypeDef DMA_InitStructure; + +/* Private function prototypes -----------------------------------------------*/ +void RCC_Configuration(void); +void GPIO_Configuration(void); + +/* Private functions ---------------------------------------------------------*/ + +/** + * @brief Main program + * @param None + * @retval None + */ +int main(void) +{ + /*!< At this stage the microcontroller clock setting is already configured, + this is done through SystemInit() function which is called from startup + file (startup_stm32f10x_xx.s) before to branch to application main. + To reconfigure the default setting of SystemInit() function, refer to + system_stm32f10x.c file + */ + + /* System Clocks Configuration */ + RCC_Configuration(); + + /* Configure the GPIO ports */ + GPIO_Configuration(); + + /* DMA1 Channel5 configuration ----------------------------------------------*/ + DMA_DeInit(DMA1_Channel5); + DMA_InitStructure.DMA_PeripheralBaseAddr = (uint32_t)TIM1_CCR1_Address; + DMA_InitStructure.DMA_MemoryBaseAddr = (uint32_t)ADC1_DR_Address; + DMA_InitStructure.DMA_DIR = DMA_DIR_PeripheralDST; + DMA_InitStructure.DMA_BufferSize = 1; + DMA_InitStructure.DMA_PeripheralInc = DMA_PeripheralInc_Disable; + DMA_InitStructure.DMA_MemoryInc = DMA_MemoryInc_Disable; + DMA_InitStructure.DMA_PeripheralDataSize = DMA_PeripheralDataSize_HalfWord; + DMA_InitStructure.DMA_MemoryDataSize = DMA_MemoryDataSize_HalfWord; + DMA_InitStructure.DMA_Mode = DMA_Mode_Circular; + DMA_InitStructure.DMA_Priority = DMA_Priority_High; + DMA_InitStructure.DMA_M2M = DMA_M2M_Disable; + DMA_Init(DMA1_Channel5, &DMA_InitStructure); + /* Enable DMA1 Channel5 */ + DMA_Cmd(DMA1_Channel5, ENABLE); + + /* ADC1 configuration ------------------------------------------------------*/ + ADC_InitStructure.ADC_Mode = ADC_Mode_Independent; + ADC_InitStructure.ADC_ScanConvMode = DISABLE; + ADC_InitStructure.ADC_ContinuousConvMode = ENABLE; + ADC_InitStructure.ADC_ExternalTrigConv = ADC_ExternalTrigConv_None; + ADC_InitStructure.ADC_DataAlign = ADC_DataAlign_Right; + ADC_InitStructure.ADC_NbrOfChannel = 1; + ADC_Init(ADC1, &ADC_InitStructure); + + /* ADC1 RegularChannelConfig Test */ + ADC_RegularChannelConfig(ADC1, ADC_Channel_14, 1, ADC_SampleTime_55Cycles5); + + /* TIM1 configuration ------------------------------------------------------*/ + /* Time Base configuration */ + TIM_TimeBaseStructInit(&TIM_TimeBaseStructure); + TIM_TimeBaseStructure.TIM_Period = 0xFF0; + TIM_TimeBaseStructure.TIM_Prescaler = 0x0; + TIM_TimeBaseStructure.TIM_ClockDivision = 0x0; + TIM_TimeBaseStructure.TIM_CounterMode = TIM_CounterMode_Up; + TIM_TimeBaseInit(TIM1, &TIM_TimeBaseStructure); + /* Channel1 Configuration in PWM mode */ + TIM_OCInitStructure.TIM_OCMode = TIM_OCMode_PWM1; + TIM_OCInitStructure.TIM_OutputState = TIM_OutputState_Enable; + TIM_OCInitStructure.TIM_OCPolarity = TIM_OCPolarity_High; + TIM_OC1Init(TIM1, &TIM_OCInitStructure); + + /* Enable TIM1 */ + TIM_Cmd(TIM1, ENABLE); + /* Enable TIM1 outputs */ + TIM_CtrlPWMOutputs(TIM1, ENABLE); + + /* Enable TIM1 DMA interface */ + TIM_DMACmd(TIM1, TIM_DMA_Update, ENABLE); + + /* Enable ADC1 */ + ADC_Cmd(ADC1, ENABLE); + + /* Enable ADC1 reset calibration register */ + ADC_ResetCalibration(ADC1); + /* Check the end of ADC1 reset calibration register */ + while(ADC_GetResetCalibrationStatus(ADC1)); + + /* Start ADC1 calibration */ + ADC_StartCalibration(ADC1); + /* Check the end of ADC1 calibration */ + while(ADC_GetCalibrationStatus(ADC1)); + + /* Start ADC1 conversion */ + ADC_SoftwareStartConvCmd(ADC1, ENABLE); + + while (1) + { + } +} + +/** + * @brief Configures the different system clocks. + * @param None + * @retval None + */ +void RCC_Configuration(void) +{ + /* ADCCLK = PCLK2/8 */ + RCC_ADCCLKConfig(RCC_PCLK2_Div8); + + /* Enable peripheral clocks ------------------------------------------------*/ + /* Enable DMA1 clock */ + RCC_AHBPeriphClockCmd(RCC_AHBPeriph_DMA1, ENABLE); + /* Enable GPIOA, GPIOC, ADC1 and TIM1 Periph clock */ + RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOA | RCC_APB2Periph_GPIOC | + RCC_APB2Periph_ADC1 | RCC_APB2Periph_TIM1, ENABLE); +} + +/** + * @brief Configures the different GPIO ports. + * @param None + * @retval None + */ +void GPIO_Configuration(void) +{ + GPIO_InitTypeDef GPIO_InitStructure; + + /* Configure TIM1 Channel1 output */ + GPIO_InitStructure.GPIO_Pin = GPIO_Pin_8; + GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AF_PP; + GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz; + GPIO_Init(GPIOA, &GPIO_InitStructure); + + /* Configure ADC Channel14 as analog input */ + GPIO_InitStructure.GPIO_Pin = GPIO_Pin_4 ; + GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AIN; + GPIO_Init(GPIOC, &GPIO_InitStructure); +} + +#ifdef USE_FULL_ASSERT + +/** + * @brief Reports the name of the source file and the source line number + * where the assert_param error has occurred. + * @param file: pointer to the source file name + * @param line: assert_param error line source number + * @retval None + */ +void assert_failed(uint8_t* file, uint32_t line) +{ + /* User can add his own implementation to report the file name and line number, + ex: printf("Wrong parameters value: file %s on line %d\r\n", file, line) */ + + /* Infinite loop */ + while (1) + { + } +} + +#endif + +/** + * @} + */ + +/** + * @} + */ + +/******************* (C) COPYRIGHT 2011 STMicroelectronics *****END OF FILE****/ diff --git a/tmp/STM32F10x_StdPeriph_Lib_V3.5.0/Project/STM32F10x_StdPeriph_Examples/DMA/ADC_TIM1/readme.txt b/tmp/STM32F10x_StdPeriph_Lib_V3.5.0/Project/STM32F10x_StdPeriph_Examples/DMA/ADC_TIM1/readme.txt new file mode 100644 index 0000000..dd93e41 --- /dev/null +++ b/tmp/STM32F10x_StdPeriph_Lib_V3.5.0/Project/STM32F10x_StdPeriph_Examples/DMA/ADC_TIM1/readme.txt @@ -0,0 +1,107 @@ +/** + @page DMA_ADC_TIM1 DMA ADC1 TIM1 example + + @verbatim + ******************** (C) COPYRIGHT 2011 STMicroelectronics ******************* + * @file DMA/ADC_TIM1/readme.txt + * @author MCD Application Team + * @version V3.5.0 + * @date 08-April-2011 + * @brief Description of the DMA ADC1 TIM1 example. + ****************************************************************************** + * THE PRESENT FIRMWARE WHICH IS FOR GUIDANCE ONLY AIMS AT PROVIDING CUSTOMERS + * WITH CODING INFORMATION REGARDING THEIR PRODUCTS IN ORDER FOR THEM TO SAVE + * TIME. AS A RESULT, STMICROELECTRONICS SHALL NOT BE HELD LIABLE FOR ANY + * DIRECT, INDIRECT OR CONSEQUENTIAL DAMAGES WITH RESPECT TO ANY CLAIMS ARISING + * FROM THE CONTENT OF SUCH FIRMWARE AND/OR THE USE MADE BY CUSTOMERS OF THE + * CODING INFORMATION CONTAINED HEREIN IN CONNECTION WITH THEIR PRODUCTS. + ****************************************************************************** + @endverbatim + +@par Example Description + +This example provides a description of how to use a DMA channel to transfer +continuously a data from a peripheral (ADC1) to another peripheral (TIM1) supporting +DMA transfer. +The ADC channel14 is configured to be converted continuously. TIM1_CH1 is configured +to generate a PWM signal on its output. +The dedicated DMA1 channel5 is configured to transfer in circular mode the last ADC +channel14 converted value to the TIM1_CCR1 register. The DMA channel request is driven +by the TIM1 update event. The duty cycle of TIM1_CH1 output signal is then changed +each time the input voltage value on ADC channel14 pin is modified. +The duty cycle variation can be visualized on oscilloscope on the TIM1_CH1 pin +PA.08 while changing the analog input on ADC channel14 using the potentiometer. + +@par Directory contents + + - DMA/ADC_TIM1/stm32f10x_conf.h Library Configuration file + - DMA/ADC_TIM1/stm32f10x_it.c Interrupt handlers + - DMA/ADC_TIM1/stm32f10x_it.h Interrupt handlers header file + - DMA/ADC_TIM1/main.c Main program + - DMA/ADC_TIM1/system_stm32f10x.c STM32F10x system source file + +@par Hardware and Software environment + + - This example runs on STM32F10x Connectivity line, High-Density, Medium-Density, + XL-Density, High-Density Value line, Medium-Density Value line, Low-Density + and Low-Density Value line Devices. + + - This example has been tested with STMicroelectronics STM32100B-EVAL (Medium-Density + Value line), STM3210C-EVAL (Connectivity line), STM3210E-EVAL (High-Density and + XL-Density) and STM3210B-EVAL (Medium-Density) evaluation boards and can be easily + tailored to any other supported device and development board. + + - STM32100B-EVAL Set-up + - Connect a variable power supply 0-3.3V to ADC Channel14 mapped on pin + PC.04 (potentiometer RV2) + - Connect an oscilloscope to TIM1_CH1 (PA.08) pin + + - STM3210C-EVAL Set-up + - Connect a variable power supply 0-3.3V to ADC Channel14 mapped on pin + PC.04 (potentiometer RV1) + - Connect an oscilloscope to TIM1_CH1 (PA.08) pin + + - STM3210E-EVAL Set-up + - Connect a variable power supply 0-3.3V to ADC Channel14 mapped on pin + PC.04 (potentiometer RV1) + - Connect an oscilloscope to TIM1_CH1 (PA.08) pin + + - STM3210B-EVAL Set-up + - Connect a variable power supply 0-3.3V to ADC Channel14 mapped on pin + PC.04 (potentiometer RV1) + - Connect an oscilloscope to TIM1_CH1 (PA.08) pin + + - STM32100E-EVAL Set-up + - Connect a variable power supply 0-3.3V to ADC Channel14 mapped on pin + PC.04 (potentiometer RV1) + - Connect an oscilloscope to TIM1_CH1 (PA.08) pin + + +@par How to use it ? + +In order to make the program work, you must do the following : + - Copy all source files from this example folder to the template folder under + Project\STM32F10x_StdPeriph_Template + - Open your preferred toolchain + - Rebuild all files and load your image into target memory + - Run the example + +@note + - Low-density Value line devices are STM32F100xx microcontrollers where the + Flash memory density ranges between 16 and 32 Kbytes. + - Low-density devices are STM32F101xx, STM32F102xx and STM32F103xx + microcontrollers where the Flash memory density ranges between 16 and 32 Kbytes. + - Medium-density Value line devices are STM32F100xx microcontrollers where + the Flash memory density ranges between 64 and 128 Kbytes. + - Medium-density devices are STM32F101xx, STM32F102xx and STM32F103xx + microcontrollers where the Flash memory density ranges between 64 and 128 Kbytes. + - High-density Value line devices are STM32F100xx microcontrollers where + the Flash memory density ranges between 256 and 512 Kbytes. + - High-density devices are STM32F101xx and STM32F103xx microcontrollers where + the Flash memory density ranges between 256 and 512 Kbytes. + - XL-density devices are STM32F101xx and STM32F103xx microcontrollers where + the Flash memory density ranges between 512 and 1024 Kbytes. + - Connectivity line devices are STM32F105xx and STM32F107xx microcontrollers. + + *

© COPYRIGHT 2011 STMicroelectronics

+ */ diff --git a/tmp/STM32F10x_StdPeriph_Lib_V3.5.0/Project/STM32F10x_StdPeriph_Examples/DMA/ADC_TIM1/stm32f10x_conf.h b/tmp/STM32F10x_StdPeriph_Lib_V3.5.0/Project/STM32F10x_StdPeriph_Examples/DMA/ADC_TIM1/stm32f10x_conf.h new file mode 100644 index 0000000..8e13530 --- /dev/null +++ b/tmp/STM32F10x_StdPeriph_Lib_V3.5.0/Project/STM32F10x_StdPeriph_Examples/DMA/ADC_TIM1/stm32f10x_conf.h @@ -0,0 +1,77 @@ +/** + ****************************************************************************** + * @file DMA/ADC_TIM1/stm32f10x_conf.h + * @author MCD Application Team + * @version V3.5.0 + * @date 08-April-2011 + * @brief Library configuration file. + ****************************************************************************** + * @attention + * + * THE PRESENT FIRMWARE WHICH IS FOR GUIDANCE ONLY AIMS AT PROVIDING CUSTOMERS + * WITH CODING INFORMATION REGARDING THEIR PRODUCTS IN ORDER FOR THEM TO SAVE + * TIME. AS A RESULT, STMICROELECTRONICS SHALL NOT BE HELD LIABLE FOR ANY + * DIRECT, INDIRECT OR CONSEQUENTIAL DAMAGES WITH RESPECT TO ANY CLAIMS ARISING + * FROM THE CONTENT OF SUCH FIRMWARE AND/OR THE USE MADE BY CUSTOMERS OF THE + * CODING INFORMATION CONTAINED HEREIN IN CONNECTION WITH THEIR PRODUCTS. + * + *

© COPYRIGHT 2011 STMicroelectronics

+ ****************************************************************************** + */ + +/* Define to prevent recursive inclusion -------------------------------------*/ +#ifndef __STM32F10x_CONF_H +#define __STM32F10x_CONF_H + +/* Includes ------------------------------------------------------------------*/ +/* Uncomment/Comment the line below to enable/disable peripheral header file inclusion */ +#include "stm32f10x_adc.h" +#include "stm32f10x_bkp.h" +#include "stm32f10x_can.h" +#include "stm32f10x_cec.h" +#include "stm32f10x_crc.h" +#include "stm32f10x_dac.h" +#include "stm32f10x_dbgmcu.h" +#include "stm32f10x_dma.h" +#include "stm32f10x_exti.h" +#include "stm32f10x_flash.h" +#include "stm32f10x_fsmc.h" +#include "stm32f10x_gpio.h" +#include "stm32f10x_i2c.h" +#include "stm32f10x_iwdg.h" +#include "stm32f10x_pwr.h" +#include "stm32f10x_rcc.h" +#include "stm32f10x_rtc.h" +#include "stm32f10x_sdio.h" +#include "stm32f10x_spi.h" +#include "stm32f10x_tim.h" +#include "stm32f10x_usart.h" +#include "stm32f10x_wwdg.h" +#include "misc.h" /* High level functions for NVIC and SysTick (add-on to CMSIS functions) */ + +/* Exported types ------------------------------------------------------------*/ +/* Exported constants --------------------------------------------------------*/ +/* Uncomment the line below to expanse the "assert_param" macro in the + Standard Peripheral Library drivers code */ +/* #define USE_FULL_ASSERT 1 */ + +/* Exported macro ------------------------------------------------------------*/ +#ifdef USE_FULL_ASSERT + +/** + * @brief The assert_param macro is used for function's parameters check. + * @param expr: If expr is false, it calls assert_failed function which reports + * the name of the source file and the source line number of the call + * that failed. If expr is true, it returns no value. + * @retval None + */ + #define assert_param(expr) ((expr) ? (void)0 : assert_failed((uint8_t *)__FILE__, __LINE__)) +/* Exported functions ------------------------------------------------------- */ + void assert_failed(uint8_t* file, uint32_t line); +#else + #define assert_param(expr) ((void)0) +#endif /* USE_FULL_ASSERT */ + +#endif /* __STM32F10x_CONF_H */ + +/******************* (C) COPYRIGHT 2011 STMicroelectronics *****END OF FILE****/ diff --git a/tmp/STM32F10x_StdPeriph_Lib_V3.5.0/Project/STM32F10x_StdPeriph_Examples/DMA/ADC_TIM1/stm32f10x_it.c b/tmp/STM32F10x_StdPeriph_Lib_V3.5.0/Project/STM32F10x_StdPeriph_Examples/DMA/ADC_TIM1/stm32f10x_it.c new file mode 100644 index 0000000..7d9f58e --- /dev/null +++ b/tmp/STM32F10x_StdPeriph_Lib_V3.5.0/Project/STM32F10x_StdPeriph_Examples/DMA/ADC_TIM1/stm32f10x_it.c @@ -0,0 +1,169 @@ +/** + ****************************************************************************** + * @file DMA/ADC_TIM1/stm32f10x_it.c + * @author MCD Application Team + * @version V3.5.0 + * @date 08-April-2011 + * @brief Main Interrupt Service Routines. + * This file provides template for all exceptions handler and peripherals + * interrupt service routine. + ****************************************************************************** + * @attention + * + * THE PRESENT FIRMWARE WHICH IS FOR GUIDANCE ONLY AIMS AT PROVIDING CUSTOMERS + * WITH CODING INFORMATION REGARDING THEIR PRODUCTS IN ORDER FOR THEM TO SAVE + * TIME. AS A RESULT, STMICROELECTRONICS SHALL NOT BE HELD LIABLE FOR ANY + * DIRECT, INDIRECT OR CONSEQUENTIAL DAMAGES WITH RESPECT TO ANY CLAIMS ARISING + * FROM THE CONTENT OF SUCH FIRMWARE AND/OR THE USE MADE BY CUSTOMERS OF THE + * CODING INFORMATION CONTAINED HEREIN IN CONNECTION WITH THEIR PRODUCTS. + * + *

© COPYRIGHT 2011 STMicroelectronics

+ ****************************************************************************** + */ + +/* Includes ------------------------------------------------------------------*/ +#include "stm32f10x_it.h" + +/** @addtogroup STM32F10x_StdPeriph_Examples + * @{ + */ + +/** @addtogroup DMA_ADC_TIM1 + * @{ + */ + +/* Private typedef -----------------------------------------------------------*/ +/* Private define ------------------------------------------------------------*/ +/* Private macro -------------------------------------------------------------*/ +/* Private variables ---------------------------------------------------------*/ +/* Private function prototypes -----------------------------------------------*/ +/* Private functions ---------------------------------------------------------*/ + +/******************************************************************************/ +/* Cortex-M3 Processor Exceptions Handlers */ +/******************************************************************************/ + +/** + * @brief This function handles NMI exception. + * @param None + * @retval None + */ +void NMI_Handler(void) +{ +} + + + +/** + * @brief This function handles Hard Fault exception. + * @param None + * @retval None + */ +void HardFault_Handler(void) +{ + /* Go to infinite loop when Hard Fault exception occurs */ + while (1) + { + } +} + +/** + * @brief This function handles Memory Manage exception. + * @param None + * @retval None + */ +void MemManage_Handler(void) +{ + /* Go to infinite loop when Memory Manage exception occurs */ + while (1) + { + } +} + +/** + * @brief This function handles Bus Fault exception. + * @param None + * @retval None + */ +void BusFault_Handler(void) +{ + /* Go to infinite loop when Bus Fault exception occurs */ + while (1) + { + } +} + +/** + * @brief This function handles Usage Fault exception. + * @param None + * @retval None + */ +void UsageFault_Handler(void) +{ + /* Go to infinite loop when Usage Fault exception occurs */ + while (1) + { + } +} + +/** + * @brief This function handles SVCall exception. + * @param None + * @retval None + */ +void SVC_Handler(void) +{ +} + +/** + * @brief This function handles Debug Monitor exception. + * @param None + * @retval None + */ +void DebugMon_Handler(void) +{ +} + +/** + * @brief This function handles PendSV_Handler exception. + * @param None + * @retval None + */ +void PendSV_Handler(void) +{ +} + +/** + * @brief This function handles SysTick Handler. + * @param None + * @retval None + */ +void SysTick_Handler(void) +{ +} + +/******************************************************************************/ +/* STM32F10x Peripherals Interrupt Handlers */ +/* Add here the Interrupt Handler for the used peripheral(s) (PPP), for the */ +/* available peripheral interrupt handler's name please refer to the startup */ +/* file (startup_stm32f10x_xx.s). */ +/******************************************************************************/ + +/** + * @brief This function handles PPP interrupt request. + * @param None + * @retval None + */ +/*void PPP_IRQHandler(void) +{ +}*/ + +/** + * @} + */ + +/** + * @} + */ + +/******************* (C) COPYRIGHT 2011 STMicroelectronics *****END OF FILE****/ diff --git a/tmp/STM32F10x_StdPeriph_Lib_V3.5.0/Project/STM32F10x_StdPeriph_Examples/DMA/ADC_TIM1/stm32f10x_it.h b/tmp/STM32F10x_StdPeriph_Lib_V3.5.0/Project/STM32F10x_StdPeriph_Examples/DMA/ADC_TIM1/stm32f10x_it.h new file mode 100644 index 0000000..5f0cc04 --- /dev/null +++ b/tmp/STM32F10x_StdPeriph_Lib_V3.5.0/Project/STM32F10x_StdPeriph_Examples/DMA/ADC_TIM1/stm32f10x_it.h @@ -0,0 +1,46 @@ +/** + ****************************************************************************** + * @file DMA/ADC_TIM1/stm32f10x_it.h + * @author MCD Application Team + * @version V3.5.0 + * @date 08-April-2011 + * @brief This file contains the headers of the interrupt handlers. + ****************************************************************************** + * @attention + * + * THE PRESENT FIRMWARE WHICH IS FOR GUIDANCE ONLY AIMS AT PROVIDING CUSTOMERS + * WITH CODING INFORMATION REGARDING THEIR PRODUCTS IN ORDER FOR THEM TO SAVE + * TIME. AS A RESULT, STMICROELECTRONICS SHALL NOT BE HELD LIABLE FOR ANY + * DIRECT, INDIRECT OR CONSEQUENTIAL DAMAGES WITH RESPECT TO ANY CLAIMS ARISING + * FROM THE CONTENT OF SUCH FIRMWARE AND/OR THE USE MADE BY CUSTOMERS OF THE + * CODING INFORMATION CONTAINED HEREIN IN CONNECTION WITH THEIR PRODUCTS. + * + *

© COPYRIGHT 2011 STMicroelectronics

+ ****************************************************************************** + */ + +/* Define to prevent recursive inclusion -------------------------------------*/ +#ifndef __STM32F10x_IT_H +#define __STM32F10x_IT_H + +/* Includes ------------------------------------------------------------------*/ +#include "stm32f10x.h" + +/* Exported types ------------------------------------------------------------*/ +/* Exported constants --------------------------------------------------------*/ +/* Exported macro ------------------------------------------------------------*/ +/* Exported functions ------------------------------------------------------- */ + +void NMI_Handler(void); +void HardFault_Handler(void); +void MemManage_Handler(void); +void BusFault_Handler(void); +void UsageFault_Handler(void); +void SVC_Handler(void); +void DebugMon_Handler(void); +void PendSV_Handler(void); +void SysTick_Handler(void); + +#endif /* __STM32F10x_IT_H */ + +/******************* (C) COPYRIGHT 2011 STMicroelectronics *****END OF FILE****/ diff --git a/tmp/STM32F10x_StdPeriph_Lib_V3.5.0/Project/STM32F10x_StdPeriph_Examples/DMA/ADC_TIM1/system_stm32f10x.c b/tmp/STM32F10x_StdPeriph_Lib_V3.5.0/Project/STM32F10x_StdPeriph_Examples/DMA/ADC_TIM1/system_stm32f10x.c new file mode 100644 index 0000000..2670e7b --- /dev/null +++ b/tmp/STM32F10x_StdPeriph_Lib_V3.5.0/Project/STM32F10x_StdPeriph_Examples/DMA/ADC_TIM1/system_stm32f10x.c @@ -0,0 +1,1094 @@ +/** + ****************************************************************************** + * @file DMA/ADC_TIM1/system_stm32f10x.c + * @author MCD Application Team + * @version V3.5.0 + * @date 08-April-2011 + * @brief CMSIS Cortex-M3 Device Peripheral Access Layer System Source File. + * + * 1. This file provides two functions and one global variable to be called from + * user application: + * - SystemInit(): Setups the system clock (System clock source, PLL Multiplier + * factors, AHB/APBx prescalers and Flash settings). + * This function is called at startup just after reset and + * before branch to main program. This call is made inside + * the "startup_stm32f10x_xx.s" file. + * + * - SystemCoreClock variable: Contains the core clock (HCLK), it can be used + * by the user application to setup the SysTick + * timer or configure other parameters. + * + * - SystemCoreClockUpdate(): Updates the variable SystemCoreClock and must + * be called whenever the core clock is changed + * during program execution. + * + * 2. After each device reset the HSI (8 MHz) is used as system clock source. + * Then SystemInit() function is called, in "startup_stm32f10x_xx.s" file, to + * configure the system clock before to branch to main program. + * + * 3. If the system clock source selected by user fails to startup, the SystemInit() + * function will do nothing and HSI still used as system clock source. User can + * add some code to deal with this issue inside the SetSysClock() function. + * + * 4. The default value of HSE crystal is set to 8 MHz (or 25 MHz, depedning on + * the product used), refer to "HSE_VALUE" define in "stm32f10x.h" file. + * When HSE is used as system clock source, directly or through PLL, and you + * are using different crystal you have to adapt the HSE value to your own + * configuration. + * + ****************************************************************************** + * @attention + * + * THE PRESENT FIRMWARE WHICH IS FOR GUIDANCE ONLY AIMS AT PROVIDING CUSTOMERS + * WITH CODING INFORMATION REGARDING THEIR PRODUCTS IN ORDER FOR THEM TO SAVE + * TIME. AS A RESULT, STMICROELECTRONICS SHALL NOT BE HELD LIABLE FOR ANY + * DIRECT, INDIRECT OR CONSEQUENTIAL DAMAGES WITH RESPECT TO ANY CLAIMS ARISING + * FROM THE CONTENT OF SUCH FIRMWARE AND/OR THE USE MADE BY CUSTOMERS OF THE + * CODING INFORMATION CONTAINED HEREIN IN CONNECTION WITH THEIR PRODUCTS. + * + *

© COPYRIGHT 2011 STMicroelectronics

+ ****************************************************************************** + */ + +/** @addtogroup CMSIS + * @{ + */ + +/** @addtogroup stm32f10x_system + * @{ + */ + +/** @addtogroup STM32F10x_System_Private_Includes + * @{ + */ + +#include "stm32f10x.h" + +/** + * @} + */ + +/** @addtogroup STM32F10x_System_Private_TypesDefinitions + * @{ + */ + +/** + * @} + */ + +/** @addtogroup STM32F10x_System_Private_Defines + * @{ + */ + +/*!< Uncomment the line corresponding to the desired System clock (SYSCLK) + frequency (after reset the HSI is used as SYSCLK source) + + IMPORTANT NOTE: + ============== + 1. After each device reset the HSI is used as System clock source. + + 2. Please make sure that the selected System clock doesn't exceed your device's + maximum frequency. + + 3. If none of the define below is enabled, the HSI is used as System clock + source. + + 4. The System clock configuration functions provided within this file assume that: + - For Low, Medium and High density Value line devices an external 8MHz + crystal is used to drive the System clock. + - For Low, Medium and High density devices an external 8MHz crystal is + used to drive the System clock. + - For Connectivity line devices an external 25MHz crystal is used to drive + the System clock. + If you are using different crystal you have to adapt those functions accordingly. + */ + +#if defined (STM32F10X_LD_VL) || (defined STM32F10X_MD_VL) || (defined STM32F10X_HD_VL) +/* #define SYSCLK_FREQ_HSE HSE_VALUE */ + #define SYSCLK_FREQ_24MHz 24000000 +#else +/* #define SYSCLK_FREQ_HSE HSE_VALUE */ +/* #define SYSCLK_FREQ_24MHz 24000000 */ +/* #define SYSCLK_FREQ_36MHz 36000000 */ +/* #define SYSCLK_FREQ_48MHz 48000000 */ +/* #define SYSCLK_FREQ_56MHz 56000000 */ +#define SYSCLK_FREQ_72MHz 72000000 +#endif + +/*!< Uncomment the following line if you need to use external SRAM mounted + on STM3210E-EVAL board (STM32 High density and XL-density devices) or on + STM32100E-EVAL board (STM32 High-density value line devices) as data memory */ +#if defined (STM32F10X_HD) || (defined STM32F10X_XL) || (defined STM32F10X_HD_VL) +/* #define DATA_IN_ExtSRAM */ +#endif + +/*!< Uncomment the following line if you need to relocate your vector Table in + Internal SRAM. */ +/* #define VECT_TAB_SRAM */ +#define VECT_TAB_OFFSET 0x0 /*!< Vector Table base offset field. + This value must be a multiple of 0x200. */ + + +/** + * @} + */ + +/** @addtogroup STM32F10x_System_Private_Macros + * @{ + */ + +/** + * @} + */ + +/** @addtogroup STM32F10x_System_Private_Variables + * @{ + */ + +/******************************************************************************* +* Clock Definitions +*******************************************************************************/ +#ifdef SYSCLK_FREQ_HSE + uint32_t SystemCoreClock = SYSCLK_FREQ_HSE; /*!< System Clock Frequency (Core Clock) */ +#elif defined SYSCLK_FREQ_24MHz + uint32_t SystemCoreClock = SYSCLK_FREQ_24MHz; /*!< System Clock Frequency (Core Clock) */ +#elif defined SYSCLK_FREQ_36MHz + uint32_t SystemCoreClock = SYSCLK_FREQ_36MHz; /*!< System Clock Frequency (Core Clock) */ +#elif defined SYSCLK_FREQ_48MHz + uint32_t SystemCoreClock = SYSCLK_FREQ_48MHz; /*!< System Clock Frequency (Core Clock) */ +#elif defined SYSCLK_FREQ_56MHz + uint32_t SystemCoreClock = SYSCLK_FREQ_56MHz; /*!< System Clock Frequency (Core Clock) */ +#elif defined SYSCLK_FREQ_72MHz + uint32_t SystemCoreClock = SYSCLK_FREQ_72MHz; /*!< System Clock Frequency (Core Clock) */ +#else /*!< HSI Selected as System Clock source */ + uint32_t SystemCoreClock = HSI_VALUE; /*!< System Clock Frequency (Core Clock) */ +#endif + +__I uint8_t AHBPrescTable[16] = {0, 0, 0, 0, 0, 0, 0, 0, 1, 2, 3, 4, 6, 7, 8, 9}; +/** + * @} + */ + +/** @addtogroup STM32F10x_System_Private_FunctionPrototypes + * @{ + */ + +static void SetSysClock(void); + +#ifdef SYSCLK_FREQ_HSE + static void SetSysClockToHSE(void); +#elif defined SYSCLK_FREQ_24MHz + static void SetSysClockTo24(void); +#elif defined SYSCLK_FREQ_36MHz + static void SetSysClockTo36(void); +#elif defined SYSCLK_FREQ_48MHz + static void SetSysClockTo48(void); +#elif defined SYSCLK_FREQ_56MHz + static void SetSysClockTo56(void); +#elif defined SYSCLK_FREQ_72MHz + static void SetSysClockTo72(void); +#endif + +#ifdef DATA_IN_ExtSRAM + static void SystemInit_ExtMemCtl(void); +#endif /* DATA_IN_ExtSRAM */ + +/** + * @} + */ + +/** @addtogroup STM32F10x_System_Private_Functions + * @{ + */ + +/** + * @brief Setup the microcontroller system + * Initialize the Embedded Flash Interface, the PLL and update the + * SystemCoreClock variable. + * @note This function should be used only after reset. + * @param None + * @retval None + */ +void SystemInit (void) +{ + /* Reset the RCC clock configuration to the default reset state(for debug purpose) */ + /* Set HSION bit */ + RCC->CR |= (uint32_t)0x00000001; + + /* Reset SW, HPRE, PPRE1, PPRE2, ADCPRE and MCO bits */ +#ifndef STM32F10X_CL + RCC->CFGR &= (uint32_t)0xF8FF0000; +#else + RCC->CFGR &= (uint32_t)0xF0FF0000; +#endif /* STM32F10X_CL */ + + /* Reset HSEON, CSSON and PLLON bits */ + RCC->CR &= (uint32_t)0xFEF6FFFF; + + /* Reset HSEBYP bit */ + RCC->CR &= (uint32_t)0xFFFBFFFF; + + /* Reset PLLSRC, PLLXTPRE, PLLMUL and USBPRE/OTGFSPRE bits */ + RCC->CFGR &= (uint32_t)0xFF80FFFF; + +#ifdef STM32F10X_CL + /* Reset PLL2ON and PLL3ON bits */ + RCC->CR &= (uint32_t)0xEBFFFFFF; + + /* Disable all interrupts and clear pending bits */ + RCC->CIR = 0x00FF0000; + + /* Reset CFGR2 register */ + RCC->CFGR2 = 0x00000000; +#elif defined (STM32F10X_LD_VL) || defined (STM32F10X_MD_VL) || (defined STM32F10X_HD_VL) + /* Disable all interrupts and clear pending bits */ + RCC->CIR = 0x009F0000; + + /* Reset CFGR2 register */ + RCC->CFGR2 = 0x00000000; +#else + /* Disable all interrupts and clear pending bits */ + RCC->CIR = 0x009F0000; +#endif /* STM32F10X_CL */ + +#if defined (STM32F10X_HD) || (defined STM32F10X_XL) || (defined STM32F10X_HD_VL) + #ifdef DATA_IN_ExtSRAM + SystemInit_ExtMemCtl(); + #endif /* DATA_IN_ExtSRAM */ +#endif + + /* Configure the System clock frequency, HCLK, PCLK2 and PCLK1 prescalers */ + /* Configure the Flash Latency cycles and enable prefetch buffer */ + SetSysClock(); + +#ifdef VECT_TAB_SRAM + SCB->VTOR = SRAM_BASE | VECT_TAB_OFFSET; /* Vector Table Relocation in Internal SRAM. */ +#else + SCB->VTOR = FLASH_BASE | VECT_TAB_OFFSET; /* Vector Table Relocation in Internal FLASH. */ +#endif +} + +/** + * @brief Update SystemCoreClock variable according to Clock Register Values. + * The SystemCoreClock variable contains the core clock (HCLK), it can + * be used by the user application to setup the SysTick timer or configure + * other parameters. + * + * @note Each time the core clock (HCLK) changes, this function must be called + * to update SystemCoreClock variable value. Otherwise, any configuration + * based on this variable will be incorrect. + * + * @note - The system frequency computed by this function is not the real + * frequency in the chip. It is calculated based on the predefined + * constant and the selected clock source: + * + * - If SYSCLK source is HSI, SystemCoreClock will contain the HSI_VALUE(*) + * + * - If SYSCLK source is HSE, SystemCoreClock will contain the HSE_VALUE(**) + * + * - If SYSCLK source is PLL, SystemCoreClock will contain the HSE_VALUE(**) + * or HSI_VALUE(*) multiplied by the PLL factors. + * + * (*) HSI_VALUE is a constant defined in stm32f1xx.h file (default value + * 8 MHz) but the real value may vary depending on the variations + * in voltage and temperature. + * + * (**) HSE_VALUE is a constant defined in stm32f1xx.h file (default value + * 8 MHz or 25 MHz, depedning on the product used), user has to ensure + * that HSE_VALUE is same as the real frequency of the crystal used. + * Otherwise, this function may have wrong result. + * + * - The result of this function could be not correct when using fractional + * value for HSE crystal. + * @param None + * @retval None + */ +void SystemCoreClockUpdate (void) +{ + uint32_t tmp = 0, pllmull = 0, pllsource = 0; + +#ifdef STM32F10X_CL + uint32_t prediv1source = 0, prediv1factor = 0, prediv2factor = 0, pll2mull = 0; +#endif /* STM32F10X_CL */ + +#if defined (STM32F10X_LD_VL) || defined (STM32F10X_MD_VL) || (defined STM32F10X_HD_VL) + uint32_t prediv1factor = 0; +#endif /* STM32F10X_LD_VL or STM32F10X_MD_VL or STM32F10X_HD_VL */ + + /* Get SYSCLK source -------------------------------------------------------*/ + tmp = RCC->CFGR & RCC_CFGR_SWS; + + switch (tmp) + { + case 0x00: /* HSI used as system clock */ + SystemCoreClock = HSI_VALUE; + break; + case 0x04: /* HSE used as system clock */ + SystemCoreClock = HSE_VALUE; + break; + case 0x08: /* PLL used as system clock */ + + /* Get PLL clock source and multiplication factor ----------------------*/ + pllmull = RCC->CFGR & RCC_CFGR_PLLMULL; + pllsource = RCC->CFGR & RCC_CFGR_PLLSRC; + +#ifndef STM32F10X_CL + pllmull = ( pllmull >> 18) + 2; + + if (pllsource == 0x00) + { + /* HSI oscillator clock divided by 2 selected as PLL clock entry */ + SystemCoreClock = (HSI_VALUE >> 1) * pllmull; + } + else + { + #if defined (STM32F10X_LD_VL) || defined (STM32F10X_MD_VL) || (defined STM32F10X_HD_VL) + prediv1factor = (RCC->CFGR2 & RCC_CFGR2_PREDIV1) + 1; + /* HSE oscillator clock selected as PREDIV1 clock entry */ + SystemCoreClock = (HSE_VALUE / prediv1factor) * pllmull; + #else + /* HSE selected as PLL clock entry */ + if ((RCC->CFGR & RCC_CFGR_PLLXTPRE) != (uint32_t)RESET) + {/* HSE oscillator clock divided by 2 */ + SystemCoreClock = (HSE_VALUE >> 1) * pllmull; + } + else + { + SystemCoreClock = HSE_VALUE * pllmull; + } + #endif + } +#else + pllmull = pllmull >> 18; + + if (pllmull != 0x0D) + { + pllmull += 2; + } + else + { /* PLL multiplication factor = PLL input clock * 6.5 */ + pllmull = 13 / 2; + } + + if (pllsource == 0x00) + { + /* HSI oscillator clock divided by 2 selected as PLL clock entry */ + SystemCoreClock = (HSI_VALUE >> 1) * pllmull; + } + else + {/* PREDIV1 selected as PLL clock entry */ + + /* Get PREDIV1 clock source and division factor */ + prediv1source = RCC->CFGR2 & RCC_CFGR2_PREDIV1SRC; + prediv1factor = (RCC->CFGR2 & RCC_CFGR2_PREDIV1) + 1; + + if (prediv1source == 0) + { + /* HSE oscillator clock selected as PREDIV1 clock entry */ + SystemCoreClock = (HSE_VALUE / prediv1factor) * pllmull; + } + else + {/* PLL2 clock selected as PREDIV1 clock entry */ + + /* Get PREDIV2 division factor and PLL2 multiplication factor */ + prediv2factor = ((RCC->CFGR2 & RCC_CFGR2_PREDIV2) >> 4) + 1; + pll2mull = ((RCC->CFGR2 & RCC_CFGR2_PLL2MUL) >> 8 ) + 2; + SystemCoreClock = (((HSE_VALUE / prediv2factor) * pll2mull) / prediv1factor) * pllmull; + } + } +#endif /* STM32F10X_CL */ + break; + + default: + SystemCoreClock = HSI_VALUE; + break; + } + + /* Compute HCLK clock frequency ----------------*/ + /* Get HCLK prescaler */ + tmp = AHBPrescTable[((RCC->CFGR & RCC_CFGR_HPRE) >> 4)]; + /* HCLK clock frequency */ + SystemCoreClock >>= tmp; +} + +/** + * @brief Configures the System clock frequency, HCLK, PCLK2 and PCLK1 prescalers. + * @param None + * @retval None + */ +static void SetSysClock(void) +{ +#ifdef SYSCLK_FREQ_HSE + SetSysClockToHSE(); +#elif defined SYSCLK_FREQ_24MHz + SetSysClockTo24(); +#elif defined SYSCLK_FREQ_36MHz + SetSysClockTo36(); +#elif defined SYSCLK_FREQ_48MHz + SetSysClockTo48(); +#elif defined SYSCLK_FREQ_56MHz + SetSysClockTo56(); +#elif defined SYSCLK_FREQ_72MHz + SetSysClockTo72(); +#endif + + /* If none of the define above is enabled, the HSI is used as System clock + source (default after reset) */ +} + +/** + * @brief Setup the external memory controller. Called in startup_stm32f10x.s + * before jump to __main + * @param None + * @retval None + */ +#ifdef DATA_IN_ExtSRAM +/** + * @brief Setup the external memory controller. + * Called in startup_stm32f10x_xx.s/.c before jump to main. + * This function configures the external SRAM mounted on STM3210E-EVAL + * board (STM32 High density devices). This SRAM will be used as program + * data memory (including heap and stack). + * @param None + * @retval None + */ +void SystemInit_ExtMemCtl(void) +{ +/*!< FSMC Bank1 NOR/SRAM3 is used for the STM3210E-EVAL, if another Bank is + required, then adjust the Register Addresses */ + + /* Enable FSMC clock */ + RCC->AHBENR = 0x00000114; + + /* Enable GPIOD, GPIOE, GPIOF and GPIOG clocks */ + RCC->APB2ENR = 0x000001E0; + +/* --------------- SRAM Data lines, NOE and NWE configuration ---------------*/ +/*---------------- SRAM Address lines configuration -------------------------*/ +/*---------------- NOE and NWE configuration --------------------------------*/ +/*---------------- NE3 configuration ----------------------------------------*/ +/*---------------- NBL0, NBL1 configuration ---------------------------------*/ + + GPIOD->CRL = 0x44BB44BB; + GPIOD->CRH = 0xBBBBBBBB; + + GPIOE->CRL = 0xB44444BB; + GPIOE->CRH = 0xBBBBBBBB; + + GPIOF->CRL = 0x44BBBBBB; + GPIOF->CRH = 0xBBBB4444; + + GPIOG->CRL = 0x44BBBBBB; + GPIOG->CRH = 0x44444B44; + +/*---------------- FSMC Configuration ---------------------------------------*/ +/*---------------- Enable FSMC Bank1_SRAM Bank ------------------------------*/ + + FSMC_Bank1->BTCR[4] = 0x00001011; + FSMC_Bank1->BTCR[5] = 0x00000200; +} +#endif /* DATA_IN_ExtSRAM */ + +#ifdef SYSCLK_FREQ_HSE +/** + * @brief Selects HSE as System clock source and configure HCLK, PCLK2 + * and PCLK1 prescalers. + * @note This function should be used only after reset. + * @param None + * @retval None + */ +static void SetSysClockToHSE(void) +{ + __IO uint32_t StartUpCounter = 0, HSEStatus = 0; + + /* SYSCLK, HCLK, PCLK2 and PCLK1 configuration ---------------------------*/ + /* Enable HSE */ + RCC->CR |= ((uint32_t)RCC_CR_HSEON); + + /* Wait till HSE is ready and if Time out is reached exit */ + do + { + HSEStatus = RCC->CR & RCC_CR_HSERDY; + StartUpCounter++; + } while((HSEStatus == 0) && (StartUpCounter != HSE_STARTUP_TIMEOUT)); + + if ((RCC->CR & RCC_CR_HSERDY) != RESET) + { + HSEStatus = (uint32_t)0x01; + } + else + { + HSEStatus = (uint32_t)0x00; + } + + if (HSEStatus == (uint32_t)0x01) + { + +#if !defined STM32F10X_LD_VL && !defined STM32F10X_MD_VL && !defined STM32F10X_HD_VL + /* Enable Prefetch Buffer */ + FLASH->ACR |= FLASH_ACR_PRFTBE; + + /* Flash 0 wait state */ + FLASH->ACR &= (uint32_t)((uint32_t)~FLASH_ACR_LATENCY); + +#ifndef STM32F10X_CL + FLASH->ACR |= (uint32_t)FLASH_ACR_LATENCY_0; +#else + if (HSE_VALUE <= 24000000) + { + FLASH->ACR |= (uint32_t)FLASH_ACR_LATENCY_0; + } + else + { + FLASH->ACR |= (uint32_t)FLASH_ACR_LATENCY_1; + } +#endif /* STM32F10X_CL */ +#endif + + /* HCLK = SYSCLK */ + RCC->CFGR |= (uint32_t)RCC_CFGR_HPRE_DIV1; + + /* PCLK2 = HCLK */ + RCC->CFGR |= (uint32_t)RCC_CFGR_PPRE2_DIV1; + + /* PCLK1 = HCLK */ + RCC->CFGR |= (uint32_t)RCC_CFGR_PPRE1_DIV1; + + /* Select HSE as system clock source */ + RCC->CFGR &= (uint32_t)((uint32_t)~(RCC_CFGR_SW)); + RCC->CFGR |= (uint32_t)RCC_CFGR_SW_HSE; + + /* Wait till HSE is used as system clock source */ + while ((RCC->CFGR & (uint32_t)RCC_CFGR_SWS) != (uint32_t)0x04) + { + } + } + else + { /* If HSE fails to start-up, the application will have wrong clock + configuration. User can add here some code to deal with this error */ + } +} +#elif defined SYSCLK_FREQ_24MHz +/** + * @brief Sets System clock frequency to 24MHz and configure HCLK, PCLK2 + * and PCLK1 prescalers. + * @note This function should be used only after reset. + * @param None + * @retval None + */ +static void SetSysClockTo24(void) +{ + __IO uint32_t StartUpCounter = 0, HSEStatus = 0; + + /* SYSCLK, HCLK, PCLK2 and PCLK1 configuration ---------------------------*/ + /* Enable HSE */ + RCC->CR |= ((uint32_t)RCC_CR_HSEON); + + /* Wait till HSE is ready and if Time out is reached exit */ + do + { + HSEStatus = RCC->CR & RCC_CR_HSERDY; + StartUpCounter++; + } while((HSEStatus == 0) && (StartUpCounter != HSE_STARTUP_TIMEOUT)); + + if ((RCC->CR & RCC_CR_HSERDY) != RESET) + { + HSEStatus = (uint32_t)0x01; + } + else + { + HSEStatus = (uint32_t)0x00; + } + + if (HSEStatus == (uint32_t)0x01) + { +#if !defined STM32F10X_LD_VL && !defined STM32F10X_MD_VL && !defined STM32F10X_HD_VL + /* Enable Prefetch Buffer */ + FLASH->ACR |= FLASH_ACR_PRFTBE; + + /* Flash 0 wait state */ + FLASH->ACR &= (uint32_t)((uint32_t)~FLASH_ACR_LATENCY); + FLASH->ACR |= (uint32_t)FLASH_ACR_LATENCY_0; +#endif + + /* HCLK = SYSCLK */ + RCC->CFGR |= (uint32_t)RCC_CFGR_HPRE_DIV1; + + /* PCLK2 = HCLK */ + RCC->CFGR |= (uint32_t)RCC_CFGR_PPRE2_DIV1; + + /* PCLK1 = HCLK */ + RCC->CFGR |= (uint32_t)RCC_CFGR_PPRE1_DIV1; + +#ifdef STM32F10X_CL + /* Configure PLLs ------------------------------------------------------*/ + /* PLL configuration: PLLCLK = PREDIV1 * 6 = 24 MHz */ + RCC->CFGR &= (uint32_t)~(RCC_CFGR_PLLXTPRE | RCC_CFGR_PLLSRC | RCC_CFGR_PLLMULL); + RCC->CFGR |= (uint32_t)(RCC_CFGR_PLLXTPRE_PREDIV1 | RCC_CFGR_PLLSRC_PREDIV1 | + RCC_CFGR_PLLMULL6); + + /* PLL2 configuration: PLL2CLK = (HSE / 5) * 8 = 40 MHz */ + /* PREDIV1 configuration: PREDIV1CLK = PLL2 / 10 = 4 MHz */ + RCC->CFGR2 &= (uint32_t)~(RCC_CFGR2_PREDIV2 | RCC_CFGR2_PLL2MUL | + RCC_CFGR2_PREDIV1 | RCC_CFGR2_PREDIV1SRC); + RCC->CFGR2 |= (uint32_t)(RCC_CFGR2_PREDIV2_DIV5 | RCC_CFGR2_PLL2MUL8 | + RCC_CFGR2_PREDIV1SRC_PLL2 | RCC_CFGR2_PREDIV1_DIV10); + + /* Enable PLL2 */ + RCC->CR |= RCC_CR_PLL2ON; + /* Wait till PLL2 is ready */ + while((RCC->CR & RCC_CR_PLL2RDY) == 0) + { + } +#elif defined (STM32F10X_LD_VL) || defined (STM32F10X_MD_VL) || defined (STM32F10X_HD_VL) + /* PLL configuration: = (HSE / 2) * 6 = 24 MHz */ + RCC->CFGR &= (uint32_t)((uint32_t)~(RCC_CFGR_PLLSRC | RCC_CFGR_PLLXTPRE | RCC_CFGR_PLLMULL)); + RCC->CFGR |= (uint32_t)(RCC_CFGR_PLLSRC_PREDIV1 | RCC_CFGR_PLLXTPRE_PREDIV1_Div2 | RCC_CFGR_PLLMULL6); +#else + /* PLL configuration: = (HSE / 2) * 6 = 24 MHz */ + RCC->CFGR &= (uint32_t)((uint32_t)~(RCC_CFGR_PLLSRC | RCC_CFGR_PLLXTPRE | RCC_CFGR_PLLMULL)); + RCC->CFGR |= (uint32_t)(RCC_CFGR_PLLSRC_HSE | RCC_CFGR_PLLXTPRE_HSE_Div2 | RCC_CFGR_PLLMULL6); +#endif /* STM32F10X_CL */ + + /* Enable PLL */ + RCC->CR |= RCC_CR_PLLON; + + /* Wait till PLL is ready */ + while((RCC->CR & RCC_CR_PLLRDY) == 0) + { + } + + /* Select PLL as system clock source */ + RCC->CFGR &= (uint32_t)((uint32_t)~(RCC_CFGR_SW)); + RCC->CFGR |= (uint32_t)RCC_CFGR_SW_PLL; + + /* Wait till PLL is used as system clock source */ + while ((RCC->CFGR & (uint32_t)RCC_CFGR_SWS) != (uint32_t)0x08) + { + } + } + else + { /* If HSE fails to start-up, the application will have wrong clock + configuration. User can add here some code to deal with this error */ + } +} +#elif defined SYSCLK_FREQ_36MHz +/** + * @brief Sets System clock frequency to 36MHz and configure HCLK, PCLK2 + * and PCLK1 prescalers. + * @note This function should be used only after reset. + * @param None + * @retval None + */ +static void SetSysClockTo36(void) +{ + __IO uint32_t StartUpCounter = 0, HSEStatus = 0; + + /* SYSCLK, HCLK, PCLK2 and PCLK1 configuration ---------------------------*/ + /* Enable HSE */ + RCC->CR |= ((uint32_t)RCC_CR_HSEON); + + /* Wait till HSE is ready and if Time out is reached exit */ + do + { + HSEStatus = RCC->CR & RCC_CR_HSERDY; + StartUpCounter++; + } while((HSEStatus == 0) && (StartUpCounter != HSE_STARTUP_TIMEOUT)); + + if ((RCC->CR & RCC_CR_HSERDY) != RESET) + { + HSEStatus = (uint32_t)0x01; + } + else + { + HSEStatus = (uint32_t)0x00; + } + + if (HSEStatus == (uint32_t)0x01) + { + /* Enable Prefetch Buffer */ + FLASH->ACR |= FLASH_ACR_PRFTBE; + + /* Flash 1 wait state */ + FLASH->ACR &= (uint32_t)((uint32_t)~FLASH_ACR_LATENCY); + FLASH->ACR |= (uint32_t)FLASH_ACR_LATENCY_1; + + /* HCLK = SYSCLK */ + RCC->CFGR |= (uint32_t)RCC_CFGR_HPRE_DIV1; + + /* PCLK2 = HCLK */ + RCC->CFGR |= (uint32_t)RCC_CFGR_PPRE2_DIV1; + + /* PCLK1 = HCLK */ + RCC->CFGR |= (uint32_t)RCC_CFGR_PPRE1_DIV1; + +#ifdef STM32F10X_CL + /* Configure PLLs ------------------------------------------------------*/ + + /* PLL configuration: PLLCLK = PREDIV1 * 9 = 36 MHz */ + RCC->CFGR &= (uint32_t)~(RCC_CFGR_PLLXTPRE | RCC_CFGR_PLLSRC | RCC_CFGR_PLLMULL); + RCC->CFGR |= (uint32_t)(RCC_CFGR_PLLXTPRE_PREDIV1 | RCC_CFGR_PLLSRC_PREDIV1 | + RCC_CFGR_PLLMULL9); + + /*!< PLL2 configuration: PLL2CLK = (HSE / 5) * 8 = 40 MHz */ + /* PREDIV1 configuration: PREDIV1CLK = PLL2 / 10 = 4 MHz */ + + RCC->CFGR2 &= (uint32_t)~(RCC_CFGR2_PREDIV2 | RCC_CFGR2_PLL2MUL | + RCC_CFGR2_PREDIV1 | RCC_CFGR2_PREDIV1SRC); + RCC->CFGR2 |= (uint32_t)(RCC_CFGR2_PREDIV2_DIV5 | RCC_CFGR2_PLL2MUL8 | + RCC_CFGR2_PREDIV1SRC_PLL2 | RCC_CFGR2_PREDIV1_DIV10); + + /* Enable PLL2 */ + RCC->CR |= RCC_CR_PLL2ON; + /* Wait till PLL2 is ready */ + while((RCC->CR & RCC_CR_PLL2RDY) == 0) + { + } + +#else + /* PLL configuration: PLLCLK = (HSE / 2) * 9 = 36 MHz */ + RCC->CFGR &= (uint32_t)((uint32_t)~(RCC_CFGR_PLLSRC | RCC_CFGR_PLLXTPRE | RCC_CFGR_PLLMULL)); + RCC->CFGR |= (uint32_t)(RCC_CFGR_PLLSRC_HSE | RCC_CFGR_PLLXTPRE_HSE_Div2 | RCC_CFGR_PLLMULL9); +#endif /* STM32F10X_CL */ + + /* Enable PLL */ + RCC->CR |= RCC_CR_PLLON; + + /* Wait till PLL is ready */ + while((RCC->CR & RCC_CR_PLLRDY) == 0) + { + } + + /* Select PLL as system clock source */ + RCC->CFGR &= (uint32_t)((uint32_t)~(RCC_CFGR_SW)); + RCC->CFGR |= (uint32_t)RCC_CFGR_SW_PLL; + + /* Wait till PLL is used as system clock source */ + while ((RCC->CFGR & (uint32_t)RCC_CFGR_SWS) != (uint32_t)0x08) + { + } + } + else + { /* If HSE fails to start-up, the application will have wrong clock + configuration. User can add here some code to deal with this error */ + } +} +#elif defined SYSCLK_FREQ_48MHz +/** + * @brief Sets System clock frequency to 48MHz and configure HCLK, PCLK2 + * and PCLK1 prescalers. + * @note This function should be used only after reset. + * @param None + * @retval None + */ +static void SetSysClockTo48(void) +{ + __IO uint32_t StartUpCounter = 0, HSEStatus = 0; + + /* SYSCLK, HCLK, PCLK2 and PCLK1 configuration ---------------------------*/ + /* Enable HSE */ + RCC->CR |= ((uint32_t)RCC_CR_HSEON); + + /* Wait till HSE is ready and if Time out is reached exit */ + do + { + HSEStatus = RCC->CR & RCC_CR_HSERDY; + StartUpCounter++; + } while((HSEStatus == 0) && (StartUpCounter != HSE_STARTUP_TIMEOUT)); + + if ((RCC->CR & RCC_CR_HSERDY) != RESET) + { + HSEStatus = (uint32_t)0x01; + } + else + { + HSEStatus = (uint32_t)0x00; + } + + if (HSEStatus == (uint32_t)0x01) + { + /* Enable Prefetch Buffer */ + FLASH->ACR |= FLASH_ACR_PRFTBE; + + /* Flash 1 wait state */ + FLASH->ACR &= (uint32_t)((uint32_t)~FLASH_ACR_LATENCY); + FLASH->ACR |= (uint32_t)FLASH_ACR_LATENCY_1; + + /* HCLK = SYSCLK */ + RCC->CFGR |= (uint32_t)RCC_CFGR_HPRE_DIV1; + + /* PCLK2 = HCLK */ + RCC->CFGR |= (uint32_t)RCC_CFGR_PPRE2_DIV1; + + /* PCLK1 = HCLK */ + RCC->CFGR |= (uint32_t)RCC_CFGR_PPRE1_DIV2; + +#ifdef STM32F10X_CL + /* Configure PLLs ------------------------------------------------------*/ + /* PLL2 configuration: PLL2CLK = (HSE / 5) * 8 = 40 MHz */ + /* PREDIV1 configuration: PREDIV1CLK = PLL2 / 5 = 8 MHz */ + + RCC->CFGR2 &= (uint32_t)~(RCC_CFGR2_PREDIV2 | RCC_CFGR2_PLL2MUL | + RCC_CFGR2_PREDIV1 | RCC_CFGR2_PREDIV1SRC); + RCC->CFGR2 |= (uint32_t)(RCC_CFGR2_PREDIV2_DIV5 | RCC_CFGR2_PLL2MUL8 | + RCC_CFGR2_PREDIV1SRC_PLL2 | RCC_CFGR2_PREDIV1_DIV5); + + /* Enable PLL2 */ + RCC->CR |= RCC_CR_PLL2ON; + /* Wait till PLL2 is ready */ + while((RCC->CR & RCC_CR_PLL2RDY) == 0) + { + } + + + /* PLL configuration: PLLCLK = PREDIV1 * 6 = 48 MHz */ + RCC->CFGR &= (uint32_t)~(RCC_CFGR_PLLXTPRE | RCC_CFGR_PLLSRC | RCC_CFGR_PLLMULL); + RCC->CFGR |= (uint32_t)(RCC_CFGR_PLLXTPRE_PREDIV1 | RCC_CFGR_PLLSRC_PREDIV1 | + RCC_CFGR_PLLMULL6); +#else + /* PLL configuration: PLLCLK = HSE * 6 = 48 MHz */ + RCC->CFGR &= (uint32_t)((uint32_t)~(RCC_CFGR_PLLSRC | RCC_CFGR_PLLXTPRE | RCC_CFGR_PLLMULL)); + RCC->CFGR |= (uint32_t)(RCC_CFGR_PLLSRC_HSE | RCC_CFGR_PLLMULL6); +#endif /* STM32F10X_CL */ + + /* Enable PLL */ + RCC->CR |= RCC_CR_PLLON; + + /* Wait till PLL is ready */ + while((RCC->CR & RCC_CR_PLLRDY) == 0) + { + } + + /* Select PLL as system clock source */ + RCC->CFGR &= (uint32_t)((uint32_t)~(RCC_CFGR_SW)); + RCC->CFGR |= (uint32_t)RCC_CFGR_SW_PLL; + + /* Wait till PLL is used as system clock source */ + while ((RCC->CFGR & (uint32_t)RCC_CFGR_SWS) != (uint32_t)0x08) + { + } + } + else + { /* If HSE fails to start-up, the application will have wrong clock + configuration. User can add here some code to deal with this error */ + } +} + +#elif defined SYSCLK_FREQ_56MHz +/** + * @brief Sets System clock frequency to 56MHz and configure HCLK, PCLK2 + * and PCLK1 prescalers. + * @note This function should be used only after reset. + * @param None + * @retval None + */ +static void SetSysClockTo56(void) +{ + __IO uint32_t StartUpCounter = 0, HSEStatus = 0; + + /* SYSCLK, HCLK, PCLK2 and PCLK1 configuration ---------------------------*/ + /* Enable HSE */ + RCC->CR |= ((uint32_t)RCC_CR_HSEON); + + /* Wait till HSE is ready and if Time out is reached exit */ + do + { + HSEStatus = RCC->CR & RCC_CR_HSERDY; + StartUpCounter++; + } while((HSEStatus == 0) && (StartUpCounter != HSE_STARTUP_TIMEOUT)); + + if ((RCC->CR & RCC_CR_HSERDY) != RESET) + { + HSEStatus = (uint32_t)0x01; + } + else + { + HSEStatus = (uint32_t)0x00; + } + + if (HSEStatus == (uint32_t)0x01) + { + /* Enable Prefetch Buffer */ + FLASH->ACR |= FLASH_ACR_PRFTBE; + + /* Flash 2 wait state */ + FLASH->ACR &= (uint32_t)((uint32_t)~FLASH_ACR_LATENCY); + FLASH->ACR |= (uint32_t)FLASH_ACR_LATENCY_2; + + /* HCLK = SYSCLK */ + RCC->CFGR |= (uint32_t)RCC_CFGR_HPRE_DIV1; + + /* PCLK2 = HCLK */ + RCC->CFGR |= (uint32_t)RCC_CFGR_PPRE2_DIV1; + + /* PCLK1 = HCLK */ + RCC->CFGR |= (uint32_t)RCC_CFGR_PPRE1_DIV2; + +#ifdef STM32F10X_CL + /* Configure PLLs ------------------------------------------------------*/ + /* PLL2 configuration: PLL2CLK = (HSE / 5) * 8 = 40 MHz */ + /* PREDIV1 configuration: PREDIV1CLK = PLL2 / 5 = 8 MHz */ + + RCC->CFGR2 &= (uint32_t)~(RCC_CFGR2_PREDIV2 | RCC_CFGR2_PLL2MUL | + RCC_CFGR2_PREDIV1 | RCC_CFGR2_PREDIV1SRC); + RCC->CFGR2 |= (uint32_t)(RCC_CFGR2_PREDIV2_DIV5 | RCC_CFGR2_PLL2MUL8 | + RCC_CFGR2_PREDIV1SRC_PLL2 | RCC_CFGR2_PREDIV1_DIV5); + + /* Enable PLL2 */ + RCC->CR |= RCC_CR_PLL2ON; + /* Wait till PLL2 is ready */ + while((RCC->CR & RCC_CR_PLL2RDY) == 0) + { + } + + + /* PLL configuration: PLLCLK = PREDIV1 * 7 = 56 MHz */ + RCC->CFGR &= (uint32_t)~(RCC_CFGR_PLLXTPRE | RCC_CFGR_PLLSRC | RCC_CFGR_PLLMULL); + RCC->CFGR |= (uint32_t)(RCC_CFGR_PLLXTPRE_PREDIV1 | RCC_CFGR_PLLSRC_PREDIV1 | + RCC_CFGR_PLLMULL7); +#else + /* PLL configuration: PLLCLK = HSE * 7 = 56 MHz */ + RCC->CFGR &= (uint32_t)((uint32_t)~(RCC_CFGR_PLLSRC | RCC_CFGR_PLLXTPRE | RCC_CFGR_PLLMULL)); + RCC->CFGR |= (uint32_t)(RCC_CFGR_PLLSRC_HSE | RCC_CFGR_PLLMULL7); + +#endif /* STM32F10X_CL */ + + /* Enable PLL */ + RCC->CR |= RCC_CR_PLLON; + + /* Wait till PLL is ready */ + while((RCC->CR & RCC_CR_PLLRDY) == 0) + { + } + + /* Select PLL as system clock source */ + RCC->CFGR &= (uint32_t)((uint32_t)~(RCC_CFGR_SW)); + RCC->CFGR |= (uint32_t)RCC_CFGR_SW_PLL; + + /* Wait till PLL is used as system clock source */ + while ((RCC->CFGR & (uint32_t)RCC_CFGR_SWS) != (uint32_t)0x08) + { + } + } + else + { /* If HSE fails to start-up, the application will have wrong clock + configuration. User can add here some code to deal with this error */ + } +} + +#elif defined SYSCLK_FREQ_72MHz +/** + * @brief Sets System clock frequency to 72MHz and configure HCLK, PCLK2 + * and PCLK1 prescalers. + * @note This function should be used only after reset. + * @param None + * @retval None + */ +static void SetSysClockTo72(void) +{ + __IO uint32_t StartUpCounter = 0, HSEStatus = 0; + + /* SYSCLK, HCLK, PCLK2 and PCLK1 configuration ---------------------------*/ + /* Enable HSE */ + RCC->CR |= ((uint32_t)RCC_CR_HSEON); + + /* Wait till HSE is ready and if Time out is reached exit */ + do + { + HSEStatus = RCC->CR & RCC_CR_HSERDY; + StartUpCounter++; + } while((HSEStatus == 0) && (StartUpCounter != HSE_STARTUP_TIMEOUT)); + + if ((RCC->CR & RCC_CR_HSERDY) != RESET) + { + HSEStatus = (uint32_t)0x01; + } + else + { + HSEStatus = (uint32_t)0x00; + } + + if (HSEStatus == (uint32_t)0x01) + { + /* Enable Prefetch Buffer */ + FLASH->ACR |= FLASH_ACR_PRFTBE; + + /* Flash 2 wait state */ + FLASH->ACR &= (uint32_t)((uint32_t)~FLASH_ACR_LATENCY); + FLASH->ACR |= (uint32_t)FLASH_ACR_LATENCY_2; + + + /* HCLK = SYSCLK */ + RCC->CFGR |= (uint32_t)RCC_CFGR_HPRE_DIV1; + + /* PCLK2 = HCLK */ + RCC->CFGR |= (uint32_t)RCC_CFGR_PPRE2_DIV1; + + /* PCLK1 = HCLK */ + RCC->CFGR |= (uint32_t)RCC_CFGR_PPRE1_DIV2; + +#ifdef STM32F10X_CL + /* Configure PLLs ------------------------------------------------------*/ + /* PLL2 configuration: PLL2CLK = (HSE / 5) * 8 = 40 MHz */ + /* PREDIV1 configuration: PREDIV1CLK = PLL2 / 5 = 8 MHz */ + + RCC->CFGR2 &= (uint32_t)~(RCC_CFGR2_PREDIV2 | RCC_CFGR2_PLL2MUL | + RCC_CFGR2_PREDIV1 | RCC_CFGR2_PREDIV1SRC); + RCC->CFGR2 |= (uint32_t)(RCC_CFGR2_PREDIV2_DIV5 | RCC_CFGR2_PLL2MUL8 | + RCC_CFGR2_PREDIV1SRC_PLL2 | RCC_CFGR2_PREDIV1_DIV5); + + /* Enable PLL2 */ + RCC->CR |= RCC_CR_PLL2ON; + /* Wait till PLL2 is ready */ + while((RCC->CR & RCC_CR_PLL2RDY) == 0) + { + } + + + /* PLL configuration: PLLCLK = PREDIV1 * 9 = 72 MHz */ + RCC->CFGR &= (uint32_t)~(RCC_CFGR_PLLXTPRE | RCC_CFGR_PLLSRC | RCC_CFGR_PLLMULL); + RCC->CFGR |= (uint32_t)(RCC_CFGR_PLLXTPRE_PREDIV1 | RCC_CFGR_PLLSRC_PREDIV1 | + RCC_CFGR_PLLMULL9); +#else + /* PLL configuration: PLLCLK = HSE * 9 = 72 MHz */ + RCC->CFGR &= (uint32_t)((uint32_t)~(RCC_CFGR_PLLSRC | RCC_CFGR_PLLXTPRE | + RCC_CFGR_PLLMULL)); + RCC->CFGR |= (uint32_t)(RCC_CFGR_PLLSRC_HSE | RCC_CFGR_PLLMULL9); +#endif /* STM32F10X_CL */ + + /* Enable PLL */ + RCC->CR |= RCC_CR_PLLON; + + /* Wait till PLL is ready */ + while((RCC->CR & RCC_CR_PLLRDY) == 0) + { + } + + /* Select PLL as system clock source */ + RCC->CFGR &= (uint32_t)((uint32_t)~(RCC_CFGR_SW)); + RCC->CFGR |= (uint32_t)RCC_CFGR_SW_PLL; + + /* Wait till PLL is used as system clock source */ + while ((RCC->CFGR & (uint32_t)RCC_CFGR_SWS) != (uint32_t)0x08) + { + } + } + else + { /* If HSE fails to start-up, the application will have wrong clock + configuration. User can add here some code to deal with this error */ + } +} +#endif + +/** + * @} + */ + +/** + * @} + */ + +/** + * @} + */ +/******************* (C) COPYRIGHT 2011 STMicroelectronics *****END OF FILE****/ diff --git a/tmp/STM32F10x_StdPeriph_Lib_V3.5.0/Project/STM32F10x_StdPeriph_Examples/DMA/Complete list of DMA examples.txt b/tmp/STM32F10x_StdPeriph_Lib_V3.5.0/Project/STM32F10x_StdPeriph_Examples/DMA/Complete list of DMA examples.txt new file mode 100644 index 0000000..5ef0865 --- /dev/null +++ b/tmp/STM32F10x_StdPeriph_Lib_V3.5.0/Project/STM32F10x_StdPeriph_Examples/DMA/Complete list of DMA examples.txt @@ -0,0 +1,61 @@ +/** + @page DMA_EXAMPLES DMA_EXAMPLES + + @verbatim + ******************** (C) COPYRIGHT 2011 STMicroelectronics ******************* + * @file DMA/readme.txt + * @author MCD Application Team + * @version V3.5.0 + * @date 08-April-2011 + * @brief STM32F10x Standard Peripherals DMA Examples List. + ****************************************************************************** + * THE PRESENT FIRMWARE WHICH IS FOR GUIDANCE ONLY AIMS AT PROVIDING CUSTOMERS + * WITH CODING INFORMATION REGARDING THEIR PRODUCTS IN ORDER FOR THEM TO SAVE + * TIME. AS A RESULT, STMICROELECTRONICS SHALL NOT BE HELD LIABLE FOR ANY + * DIRECT, INDIRECT OR CONSEQUENTIAL DAMAGES WITH RESPECT TO ANY CLAIMS ARISING + * FROM THE CONTENT OF SUCH FIRMWARE AND/OR THE USE MADE BY CUSTOMERS OF THE + * CODING INFORMATION CONTAINED HEREIN IN CONNECTION WITH THEIR PRODUCTS. + ****************************************************************************** + @endverbatim + +In addition to these examples, there are other examples using the DMA peripheral: + + * + +@note + - Low-density Value line devices are STM32F100xx microcontrollers where the + Flash memory density ranges between 16 and 32 Kbytes. + - Low-density devices are STM32F101xx, STM32F102xx and STM32F103xx + microcontrollers where the Flash memory density ranges between 16 and 32 Kbytes. + - Medium-density Value line devices are STM32F100xx microcontrollers where + the Flash memory density ranges between 64 and 128 Kbytes. + - Medium-density devices are STM32F101xx, STM32F102xx and STM32F103xx + microcontrollers where the Flash memory density ranges between 64 and 128 Kbytes. + - High-density Value line devices are STM32F100xx microcontrollers where + the Flash memory density ranges between 256 and 512 Kbytes. + - High-density devices are STM32F101xx and STM32F103xx microcontrollers where + the Flash memory density ranges between 256 and 512 Kbytes. + - XL-density devices are STM32F101xx and STM32F103xx microcontrollers where + the Flash memory density ranges between 512 and 1024 Kbytes. + - Connectivity line devices are STM32F105xx and STM32F107xx microcontrollers. + + *

© COPYRIGHT 2011 STMicroelectronics

+ */ diff --git a/tmp/STM32F10x_StdPeriph_Lib_V3.5.0/Project/STM32F10x_StdPeriph_Examples/DMA/FLASH_RAM/main.c b/tmp/STM32F10x_StdPeriph_Lib_V3.5.0/Project/STM32F10x_StdPeriph_Examples/DMA/FLASH_RAM/main.c new file mode 100644 index 0000000..379023d --- /dev/null +++ b/tmp/STM32F10x_StdPeriph_Lib_V3.5.0/Project/STM32F10x_StdPeriph_Examples/DMA/FLASH_RAM/main.c @@ -0,0 +1,206 @@ +/** + ****************************************************************************** + * @file DMA/FLASH_RAM/main.c + * @author MCD Application Team + * @version V3.5.0 + * @date 08-April-2011 + * @brief Main program body + ****************************************************************************** + * @attention + * + * THE PRESENT FIRMWARE WHICH IS FOR GUIDANCE ONLY AIMS AT PROVIDING CUSTOMERS + * WITH CODING INFORMATION REGARDING THEIR PRODUCTS IN ORDER FOR THEM TO SAVE + * TIME. AS A RESULT, STMICROELECTRONICS SHALL NOT BE HELD LIABLE FOR ANY + * DIRECT, INDIRECT OR CONSEQUENTIAL DAMAGES WITH RESPECT TO ANY CLAIMS ARISING + * FROM THE CONTENT OF SUCH FIRMWARE AND/OR THE USE MADE BY CUSTOMERS OF THE + * CODING INFORMATION CONTAINED HEREIN IN CONNECTION WITH THEIR PRODUCTS. + * + *

© COPYRIGHT 2011 STMicroelectronics

+ ****************************************************************************** + */ + +/* Includes ------------------------------------------------------------------*/ +#include "stm32f10x.h" + +/** @addtogroup STM32F10x_StdPeriph_Examples + * @{ + */ + +/** @addtogroup DMA_FLASH_RAM + * @{ + */ + +/* Private typedef -----------------------------------------------------------*/ +typedef enum {FAILED = 0, PASSED = !FAILED} TestStatus; + +/* Private define ------------------------------------------------------------*/ +#define BufferSize 32 + +/* Private macro -------------------------------------------------------------*/ +/* Private variables ---------------------------------------------------------*/ +DMA_InitTypeDef DMA_InitStructure; +__IO uint32_t CurrDataCounterBegin = 0; +__IO uint32_t CurrDataCounterEnd = 0x01; /* This variable should not be initialized to 0 */ + +TestStatus TransferStatus = FAILED; +const uint32_t SRC_Const_Buffer[BufferSize]= { + 0x01020304,0x05060708,0x090A0B0C,0x0D0E0F10, + 0x11121314,0x15161718,0x191A1B1C,0x1D1E1F20, + 0x21222324,0x25262728,0x292A2B2C,0x2D2E2F30, + 0x31323334,0x35363738,0x393A3B3C,0x3D3E3F40, + 0x41424344,0x45464748,0x494A4B4C,0x4D4E4F50, + 0x51525354,0x55565758,0x595A5B5C,0x5D5E5F60, + 0x61626364,0x65666768,0x696A6B6C,0x6D6E6F70, + 0x71727374,0x75767778,0x797A7B7C,0x7D7E7F80}; +uint32_t DST_Buffer[BufferSize]; + +/* Private function prototypes -----------------------------------------------*/ +void RCC_Configuration(void); +void NVIC_Configuration(void); +TestStatus Buffercmp(const uint32_t* pBuffer, uint32_t* pBuffer1, uint16_t BufferLength); + +/* Private functions ---------------------------------------------------------*/ + +/** + * @brief Main program + * @param None + * @retval None + */ +int main(void) +{ + /*!< At this stage the microcontroller clock setting is already configured, + this is done through SystemInit() function which is called from startup + file (startup_stm32f10x_xx.s) before to branch to application main. + To reconfigure the default setting of SystemInit() function, refer to + system_stm32f10x.c file + */ + + /* System Clocks Configuration */ + RCC_Configuration(); + + /* NVIC configuration */ + NVIC_Configuration(); + + /* DMA1 channel6 configuration */ + DMA_DeInit(DMA1_Channel6); + DMA_InitStructure.DMA_PeripheralBaseAddr = (uint32_t)SRC_Const_Buffer; + DMA_InitStructure.DMA_MemoryBaseAddr = (uint32_t)DST_Buffer; + DMA_InitStructure.DMA_DIR = DMA_DIR_PeripheralSRC; + DMA_InitStructure.DMA_BufferSize = BufferSize; + DMA_InitStructure.DMA_PeripheralInc = DMA_PeripheralInc_Enable; + DMA_InitStructure.DMA_MemoryInc = DMA_MemoryInc_Enable; + DMA_InitStructure.DMA_PeripheralDataSize = DMA_PeripheralDataSize_Word; + DMA_InitStructure.DMA_MemoryDataSize = DMA_MemoryDataSize_Word; + DMA_InitStructure.DMA_Mode = DMA_Mode_Normal; + DMA_InitStructure.DMA_Priority = DMA_Priority_High; + DMA_InitStructure.DMA_M2M = DMA_M2M_Enable; + DMA_Init(DMA1_Channel6, &DMA_InitStructure); + + /* Enable DMA1 Channel6 Transfer Complete interrupt */ + DMA_ITConfig(DMA1_Channel6, DMA_IT_TC, ENABLE); + + /* Get Current Data Counter value before transfer begins */ + CurrDataCounterBegin = DMA_GetCurrDataCounter(DMA1_Channel6); + + /* Enable DMA1 Channel6 transfer */ + DMA_Cmd(DMA1_Channel6, ENABLE); + + /* Wait the end of transmission */ + while (CurrDataCounterEnd != 0) + { + } + + /* Check if the transmitted and received data are equal */ + TransferStatus = Buffercmp(SRC_Const_Buffer, DST_Buffer, BufferSize); + /* TransferStatus = PASSED, if the transmitted and received data + are the same */ + /* TransferStatus = FAILED, if the transmitted and received data + are different */ + + while (1) + { + } +} + +/** + * @brief Configures the different system clocks. + * @param None + * @retval None + */ +void RCC_Configuration(void) +{ + /* Enable peripheral clocks ------------------------------------------------*/ + /* Enable DMA1 clock */ + RCC_AHBPeriphClockCmd(RCC_AHBPeriph_DMA1, ENABLE); +} + +/** + * @brief Configure the nested vectored interrupt controller. + * @param None + * @retval None + */ +void NVIC_Configuration(void) +{ + NVIC_InitTypeDef NVIC_InitStructure; + + /* Enable DMA1 channel6 IRQ Channel */ + NVIC_InitStructure.NVIC_IRQChannel = DMA1_Channel6_IRQn; + NVIC_InitStructure.NVIC_IRQChannelPreemptionPriority = 0; + NVIC_InitStructure.NVIC_IRQChannelSubPriority = 0; + NVIC_InitStructure.NVIC_IRQChannelCmd = ENABLE; + NVIC_Init(&NVIC_InitStructure); +} + +/** + * @brief Compares two buffers. + * @param pBuffer, pBuffer1: buffers to be compared. + * @param BufferLength: buffer's length + * @retval PASSED: pBuffer identical to pBuffer1 + * FAILED: pBuffer differs from pBuffer1 + */ +TestStatus Buffercmp(const uint32_t* pBuffer, uint32_t* pBuffer1, uint16_t BufferLength) +{ + while(BufferLength--) + { + if(*pBuffer != *pBuffer1) + { + return FAILED; + } + + pBuffer++; + pBuffer1++; + } + + return PASSED; +} + +#ifdef USE_FULL_ASSERT + +/** + * @brief Reports the name of the source file and the source line number + * where the assert_param error has occurred. + * @param file: pointer to the source file name + * @param line: assert_param error line source number + * @retval None + */ +void assert_failed(uint8_t* file, uint32_t line) +{ + /* User can add his own implementation to report the file name and line number, + ex: printf("Wrong parameters value: file %s on line %d\r\n", file, line) */ + + /* Infinite loop */ + while (1) + { + } +} + +#endif +/** + * @} + */ + +/** + * @} + */ + +/******************* (C) COPYRIGHT 2011 STMicroelectronics *****END OF FILE****/ diff --git a/tmp/STM32F10x_StdPeriph_Lib_V3.5.0/Project/STM32F10x_StdPeriph_Examples/DMA/FLASH_RAM/readme.txt b/tmp/STM32F10x_StdPeriph_Lib_V3.5.0/Project/STM32F10x_StdPeriph_Examples/DMA/FLASH_RAM/readme.txt new file mode 100644 index 0000000..caa5689 --- /dev/null +++ b/tmp/STM32F10x_StdPeriph_Lib_V3.5.0/Project/STM32F10x_StdPeriph_Examples/DMA/FLASH_RAM/readme.txt @@ -0,0 +1,87 @@ +/** + @page DMA_FLASH_RAM DMA FLASH to RAM example + + @verbatim + ******************** (C) COPYRIGHT 2011 STMicroelectronics ******************* + * @file DMA/FLASH_RAM/readme.txt + * @author MCD Application Team + * @version V3.5.0 + * @date 08-April-2011 + * @brief Description of the DMA FLASH to RAM example. + ****************************************************************************** + * THE PRESENT FIRMWARE WHICH IS FOR GUIDANCE ONLY AIMS AT PROVIDING CUSTOMERS + * WITH CODING INFORMATION REGARDING THEIR PRODUCTS IN ORDER FOR THEM TO SAVE + * TIME. AS A RESULT, STMICROELECTRONICS SHALL NOT BE HELD LIABLE FOR ANY + * DIRECT, INDIRECT OR CONSEQUENTIAL DAMAGES WITH RESPECT TO ANY CLAIMS ARISING + * FROM THE CONTENT OF SUCH FIRMWARE AND/OR THE USE MADE BY CUSTOMERS OF THE + * CODING INFORMATION CONTAINED HEREIN IN CONNECTION WITH THEIR PRODUCTS. + ****************************************************************************** + @endverbatim + +@par Example Description + +This example provides a description of how to use a DMA channel to transfer +a word data buffer from FLASH memory to embedded SRAM memory. + +DMA1 Channel6 is configured to transfer the contents of a 32-word data buffer +stored in Flash memory to the reception buffer declared in RAM. + +The start of transfer is triggered by software. DMA1 Channel6 memory-to-memory +transfer is enabled. Source and destination addresses incrementing is also enabled. +The transfer is started by setting the Channel enable bit for DMA1 Channel6. +At the end of the transfer a Transfer Complete interrupt is generated since it +is enabled. Once interrupt is generated, the remaining data to be transferred is +read which must be equal to 0. The Transfer Complete Interrupt pending bit is +then cleared. A comparison between the source and destination buffers is done to +check that all data have been correctly transferred. + + +@par Directory contents + + - DMA/FLASH_RAM/stm32f10x_conf.h Library Configuration file + - DMA/FLASH_RAM/stm32f10x_it.c Interrupt handlers + - DMA/FLASH_RAM/stm32f10x_it.h Interrupt handlers header file + - DMA/FLASH_RAM/main.c Main program + - DMA/FLASH_RAM/system_stm32f10x.c STM32F10x system source file + +@par Hardware and Software environment + + - This example runs on STM32F10x Connectivity line, High-Density, Medium-Density, + XL-Density,High-Density Value line, Medium-Density Value line, Low-Density + and Low-Density Value line Devices. + + - This example has been tested with STMicroelectronics STM32100B-EVAL (Medium-Density + Value line), STM3210C-EVAL (Connectivity line), STM3210E-EVAL (High-Density + and XL-Density), STM32100E-EVAL (High-Density Value line) and STM3210B-EVAL + (Medium-Density) evaluation boards and can be easily tailored to any other + supported device and development board. + + +@par How to use it ? + +In order to make the program work, you must do the following : + - Copy all source files from this example folder to the template folder under + Project\STM32F10x_StdPeriph_Template + - Open your preferred toolchain + - Rebuild all files and load your image into target memory + - Run the example + +@note + - Low-density Value line devices are STM32F100xx microcontrollers where the + Flash memory density ranges between 16 and 32 Kbytes. + - Low-density devices are STM32F101xx, STM32F102xx and STM32F103xx + microcontrollers where the Flash memory density ranges between 16 and 32 Kbytes. + - Medium-density Value line devices are STM32F100xx microcontrollers where + the Flash memory density ranges between 64 and 128 Kbytes. + - Medium-density devices are STM32F101xx, STM32F102xx and STM32F103xx + microcontrollers where the Flash memory density ranges between 64 and 128 Kbytes. + - High-density Value line devices are STM32F100xx microcontrollers where + the Flash memory density ranges between 256 and 512 Kbytes. + - High-density devices are STM32F101xx and STM32F103xx microcontrollers where + the Flash memory density ranges between 256 and 512 Kbytes. + - XL-density devices are STM32F101xx and STM32F103xx microcontrollers where + the Flash memory density ranges between 512 and 1024 Kbytes. + - Connectivity line devices are STM32F105xx and STM32F107xx microcontrollers. + + *

© COPYRIGHT 2011 STMicroelectronics

+ */ diff --git a/tmp/STM32F10x_StdPeriph_Lib_V3.5.0/Project/STM32F10x_StdPeriph_Examples/DMA/FLASH_RAM/stm32f10x_conf.h b/tmp/STM32F10x_StdPeriph_Lib_V3.5.0/Project/STM32F10x_StdPeriph_Examples/DMA/FLASH_RAM/stm32f10x_conf.h new file mode 100644 index 0000000..474afcc --- /dev/null +++ b/tmp/STM32F10x_StdPeriph_Lib_V3.5.0/Project/STM32F10x_StdPeriph_Examples/DMA/FLASH_RAM/stm32f10x_conf.h @@ -0,0 +1,78 @@ +/** + ****************************************************************************** + * @file DMA/FLASH_RAM/stm32f10x_conf.h + * @author MCD Application Team + * @version V3.5.0 + * @date 08-April-2011 + * @brief Library configuration file. + ****************************************************************************** + * @attention + * + * THE PRESENT FIRMWARE WHICH IS FOR GUIDANCE ONLY AIMS AT PROVIDING CUSTOMERS + * WITH CODING INFORMATION REGARDING THEIR PRODUCTS IN ORDER FOR THEM TO SAVE + * TIME. AS A RESULT, STMICROELECTRONICS SHALL NOT BE HELD LIABLE FOR ANY + * DIRECT, INDIRECT OR CONSEQUENTIAL DAMAGES WITH RESPECT TO ANY CLAIMS ARISING + * FROM THE CONTENT OF SUCH FIRMWARE AND/OR THE USE MADE BY CUSTOMERS OF THE + * CODING INFORMATION CONTAINED HEREIN IN CONNECTION WITH THEIR PRODUCTS. + * + *

© COPYRIGHT 2011 STMicroelectronics

+ ****************************************************************************** + */ + +/* Define to prevent recursive inclusion -------------------------------------*/ +#ifndef __STM32F10x_CONF_H +#define __STM32F10x_CONF_H + +/* Includes ------------------------------------------------------------------*/ +/* Uncomment/Comment the line below to enable/disable peripheral header file inclusion */ +#include "stm32f10x_adc.h" +#include "stm32f10x_bkp.h" +#include "stm32f10x_can.h" +#include "stm32f10x_cec.h" +#include "stm32f10x_crc.h" +#include "stm32f10x_dac.h" +#include "stm32f10x_dbgmcu.h" +#include "stm32f10x_dma.h" +#include "stm32f10x_exti.h" +#include "stm32f10x_flash.h" +#include "stm32f10x_fsmc.h" +#include "stm32f10x_gpio.h" +#include "stm32f10x_i2c.h" +#include "stm32f10x_iwdg.h" +#include "stm32f10x_pwr.h" +#include "stm32f10x_rcc.h" +#include "stm32f10x_rtc.h" +#include "stm32f10x_sdio.h" +#include "stm32f10x_spi.h" +#include "stm32f10x_tim.h" +#include "stm32f10x_usart.h" +#include "stm32f10x_wwdg.h" +#include "misc.h" /* High level functions for NVIC and SysTick (add-on to CMSIS functions) */ + + +/* Exported types ------------------------------------------------------------*/ +/* Exported constants --------------------------------------------------------*/ +/* Uncomment the line below to expanse the "assert_param" macro in the + Standard Peripheral Library drivers code */ +/* #define USE_FULL_ASSERT 1 */ + +/* Exported macro ------------------------------------------------------------*/ +#ifdef USE_FULL_ASSERT + +/** + * @brief The assert_param macro is used for function's parameters check. + * @param expr: If expr is false, it calls assert_failed function which reports + * the name of the source file and the source line number of the call + * that failed. If expr is true, it returns no value. + * @retval None + */ + #define assert_param(expr) ((expr) ? (void)0 : assert_failed((uint8_t *)__FILE__, __LINE__)) +/* Exported functions ------------------------------------------------------- */ + void assert_failed(uint8_t* file, uint32_t line); +#else + #define assert_param(expr) ((void)0) +#endif /* USE_FULL_ASSERT */ + +#endif /* __STM32F10x_CONF_H */ + +/******************* (C) COPYRIGHT 2011 STMicroelectronics *****END OF FILE****/ diff --git a/tmp/STM32F10x_StdPeriph_Lib_V3.5.0/Project/STM32F10x_StdPeriph_Examples/DMA/FLASH_RAM/stm32f10x_it.c b/tmp/STM32F10x_StdPeriph_Lib_V3.5.0/Project/STM32F10x_StdPeriph_Examples/DMA/FLASH_RAM/stm32f10x_it.c new file mode 100644 index 0000000..4288f07 --- /dev/null +++ b/tmp/STM32F10x_StdPeriph_Lib_V3.5.0/Project/STM32F10x_StdPeriph_Examples/DMA/FLASH_RAM/stm32f10x_it.c @@ -0,0 +1,190 @@ +/** + ****************************************************************************** + * @file DMA/FLASH_RAM/stm32f10x_it.c + * @author MCD Application Team + * @version V3.5.0 + * @date 08-April-2011 + * @brief Main Interrupt Service Routines. + * This file provides template for all exceptions handler and peripherals + * interrupt service routine. + ****************************************************************************** + * @attention + * + * THE PRESENT FIRMWARE WHICH IS FOR GUIDANCE ONLY AIMS AT PROVIDING CUSTOMERS + * WITH CODING INFORMATION REGARDING THEIR PRODUCTS IN ORDER FOR THEM TO SAVE + * TIME. AS A RESULT, STMICROELECTRONICS SHALL NOT BE HELD LIABLE FOR ANY + * DIRECT, INDIRECT OR CONSEQUENTIAL DAMAGES WITH RESPECT TO ANY CLAIMS ARISING + * FROM THE CONTENT OF SUCH FIRMWARE AND/OR THE USE MADE BY CUSTOMERS OF THE + * CODING INFORMATION CONTAINED HEREIN IN CONNECTION WITH THEIR PRODUCTS. + * + *

© COPYRIGHT 2011 STMicroelectronics

+ ****************************************************************************** + */ + +/* Includes ------------------------------------------------------------------*/ +#include "stm32f10x_it.h" + +/** @addtogroup STM32F10x_StdPeriph_Examples + * @{ + */ + +/** @addtogroup DMA_FLASH_RAM + * @{ + */ + +/* Private typedef -----------------------------------------------------------*/ +/* Private define ------------------------------------------------------------*/ +/* Private macro -------------------------------------------------------------*/ +/* Private variables ---------------------------------------------------------*/ +extern __IO uint16_t CurrDataCounterEnd; + +/* Private function prototypes -----------------------------------------------*/ +/* Private functions ---------------------------------------------------------*/ + +/******************************************************************************/ +/* Cortex-M3 Processor Exceptions Handlers */ +/******************************************************************************/ + +/** + * @brief This function handles NMI exception. + * @param None + * @retval None + */ +void NMI_Handler(void) +{ +} + +/** + * @brief This function handles Hard Fault exception. + * @param None + * @retval None + */ +void HardFault_Handler(void) +{ + /* Go to infinite loop when Hard Fault exception occurs */ + while (1) + { + } +} + +/** + * @brief This function handles Memory Manage exception. + * @param None + * @retval None + */ +void MemManage_Handler(void) +{ + /* Go to infinite loop when Memory Manage exception occurs */ + while (1) + { + } +} + +/** + * @brief This function handles Bus Fault exception. + * @param None + * @retval None + */ +void BusFault_Handler(void) +{ + /* Go to infinite loop when Bus Fault exception occurs */ + while (1) + { + } +} + +/** + * @brief This function handles Usage Fault exception. + * @param None + * @retval None + */ +void UsageFault_Handler(void) +{ + /* Go to infinite loop when Usage Fault exception occurs */ + while (1) + { + } +} + +/** + * @brief This function handles SVCall exception. + * @param None + * @retval None + */ +void SVC_Handler(void) +{ +} + +/** + * @brief This function handles Debug Monitor exception. + * @param None + * @retval None + */ +void DebugMon_Handler(void) +{ +} + +/** + * @brief This function handles PendSV_Handler exception. + * @param None + * @retval None + */ +void PendSV_Handler(void) +{ +} + +/** + * @brief This function handles SysTick Handler. + * @param None + * @retval None + */ +void SysTick_Handler(void) +{ +} + +/******************************************************************************/ +/* STM32F10x Peripherals Interrupt Handlers */ +/******************************************************************************/ + +/** + * @brief This function handles DMA1 Channel 6 interrupt request. + * @param None + * @retval None + */ +void DMA1_Channel6_IRQHandler(void) +{ + /* Test on DMA1 Channel6 Transfer Complete interrupt */ + if(DMA_GetITStatus(DMA1_IT_TC6)) + { + /* Get Current Data Counter value after complete transfer */ + CurrDataCounterEnd = DMA_GetCurrDataCounter(DMA1_Channel6); + /* Clear DMA1 Channel6 Half Transfer, Transfer Complete and Global interrupt pending bits */ + DMA_ClearITPendingBit(DMA1_IT_GL6); + } +} + +/******************************************************************************/ +/* STM32F10x Peripherals Interrupt Handlers */ +/* Add here the Interrupt Handler for the used peripheral(s) (PPP), for the */ +/* available peripheral interrupt handler's name please refer to the startup */ +/* file (startup_stm32f10x_xx.s). */ +/******************************************************************************/ + +/** + * @brief This function handles PPP interrupt request. + * @param None + * @retval None + */ +/*void PPP_IRQHandler(void) +{ +}*/ + +/** + * @} + */ + +/** + * @} + */ + +/******************* (C) COPYRIGHT 2011 STMicroelectronics *****END OF FILE****/ diff --git a/tmp/STM32F10x_StdPeriph_Lib_V3.5.0/Project/STM32F10x_StdPeriph_Examples/DMA/FLASH_RAM/stm32f10x_it.h b/tmp/STM32F10x_StdPeriph_Lib_V3.5.0/Project/STM32F10x_StdPeriph_Examples/DMA/FLASH_RAM/stm32f10x_it.h new file mode 100644 index 0000000..e90099f --- /dev/null +++ b/tmp/STM32F10x_StdPeriph_Lib_V3.5.0/Project/STM32F10x_StdPeriph_Examples/DMA/FLASH_RAM/stm32f10x_it.h @@ -0,0 +1,47 @@ +/** + ****************************************************************************** + * @file DMA/FLASH_RAM/stm32f10x_it.h + * @author MCD Application Team + * @version V3.5.0 + * @date 08-April-2011 + * @brief This file contains the headers of the interrupt handlers. + ****************************************************************************** + * @attention + * + * THE PRESENT FIRMWARE WHICH IS FOR GUIDANCE ONLY AIMS AT PROVIDING CUSTOMERS + * WITH CODING INFORMATION REGARDING THEIR PRODUCTS IN ORDER FOR THEM TO SAVE + * TIME. AS A RESULT, STMICROELECTRONICS SHALL NOT BE HELD LIABLE FOR ANY + * DIRECT, INDIRECT OR CONSEQUENTIAL DAMAGES WITH RESPECT TO ANY CLAIMS ARISING + * FROM THE CONTENT OF SUCH FIRMWARE AND/OR THE USE MADE BY CUSTOMERS OF THE + * CODING INFORMATION CONTAINED HEREIN IN CONNECTION WITH THEIR PRODUCTS. + * + *

© COPYRIGHT 2011 STMicroelectronics

+ ****************************************************************************** + */ + +/* Define to prevent recursive inclusion -------------------------------------*/ +#ifndef __STM32F10x_IT_H +#define __STM32F10x_IT_H + +/* Includes ------------------------------------------------------------------*/ +#include "stm32f10x.h" + +/* Exported types ------------------------------------------------------------*/ +/* Exported constants --------------------------------------------------------*/ +/* Exported macro ------------------------------------------------------------*/ +/* Exported functions ------------------------------------------------------- */ + +void NMI_Handler(void); +void HardFault_Handler(void); +void MemManage_Handler(void); +void BusFault_Handler(void); +void UsageFault_Handler(void); +void SVC_Handler(void); +void DebugMon_Handler(void); +void PendSV_Handler(void); +void SysTick_Handler(void); +void DMA1_Channel6_IRQHandler(void); + +#endif /* __STM32F10x_IT_H */ + +/******************* (C) COPYRIGHT 2011 STMicroelectronics *****END OF FILE****/ diff --git a/tmp/STM32F10x_StdPeriph_Lib_V3.5.0/Project/STM32F10x_StdPeriph_Examples/DMA/FLASH_RAM/system_stm32f10x.c b/tmp/STM32F10x_StdPeriph_Lib_V3.5.0/Project/STM32F10x_StdPeriph_Examples/DMA/FLASH_RAM/system_stm32f10x.c new file mode 100644 index 0000000..8e7f882 --- /dev/null +++ b/tmp/STM32F10x_StdPeriph_Lib_V3.5.0/Project/STM32F10x_StdPeriph_Examples/DMA/FLASH_RAM/system_stm32f10x.c @@ -0,0 +1,1094 @@ +/** + ****************************************************************************** + * @file DMA/FLASH_RAM/system_stm32f10x.c + * @author MCD Application Team + * @version V3.5.0 + * @date 08-April-2011 + * @brief CMSIS Cortex-M3 Device Peripheral Access Layer System Source File. + * + * 1. This file provides two functions and one global variable to be called from + * user application: + * - SystemInit(): Setups the system clock (System clock source, PLL Multiplier + * factors, AHB/APBx prescalers and Flash settings). + * This function is called at startup just after reset and + * before branch to main program. This call is made inside + * the "startup_stm32f10x_xx.s" file. + * + * - SystemCoreClock variable: Contains the core clock (HCLK), it can be used + * by the user application to setup the SysTick + * timer or configure other parameters. + * + * - SystemCoreClockUpdate(): Updates the variable SystemCoreClock and must + * be called whenever the core clock is changed + * during program execution. + * + * 2. After each device reset the HSI (8 MHz) is used as system clock source. + * Then SystemInit() function is called, in "startup_stm32f10x_xx.s" file, to + * configure the system clock before to branch to main program. + * + * 3. If the system clock source selected by user fails to startup, the SystemInit() + * function will do nothing and HSI still used as system clock source. User can + * add some code to deal with this issue inside the SetSysClock() function. + * + * 4. The default value of HSE crystal is set to 8 MHz (or 25 MHz, depedning on + * the product used), refer to "HSE_VALUE" define in "stm32f10x.h" file. + * When HSE is used as system clock source, directly or through PLL, and you + * are using different crystal you have to adapt the HSE value to your own + * configuration. + * + ****************************************************************************** + * @attention + * + * THE PRESENT FIRMWARE WHICH IS FOR GUIDANCE ONLY AIMS AT PROVIDING CUSTOMERS + * WITH CODING INFORMATION REGARDING THEIR PRODUCTS IN ORDER FOR THEM TO SAVE + * TIME. AS A RESULT, STMICROELECTRONICS SHALL NOT BE HELD LIABLE FOR ANY + * DIRECT, INDIRECT OR CONSEQUENTIAL DAMAGES WITH RESPECT TO ANY CLAIMS ARISING + * FROM THE CONTENT OF SUCH FIRMWARE AND/OR THE USE MADE BY CUSTOMERS OF THE + * CODING INFORMATION CONTAINED HEREIN IN CONNECTION WITH THEIR PRODUCTS. + * + *

© COPYRIGHT 2011 STMicroelectronics

+ ****************************************************************************** + */ + +/** @addtogroup CMSIS + * @{ + */ + +/** @addtogroup stm32f10x_system + * @{ + */ + +/** @addtogroup STM32F10x_System_Private_Includes + * @{ + */ + +#include "stm32f10x.h" + +/** + * @} + */ + +/** @addtogroup STM32F10x_System_Private_TypesDefinitions + * @{ + */ + +/** + * @} + */ + +/** @addtogroup STM32F10x_System_Private_Defines + * @{ + */ + +/*!< Uncomment the line corresponding to the desired System clock (SYSCLK) + frequency (after reset the HSI is used as SYSCLK source) + + IMPORTANT NOTE: + ============== + 1. After each device reset the HSI is used as System clock source. + + 2. Please make sure that the selected System clock doesn't exceed your device's + maximum frequency. + + 3. If none of the define below is enabled, the HSI is used as System clock + source. + + 4. The System clock configuration functions provided within this file assume that: + - For Low, Medium and High density Value line devices an external 8MHz + crystal is used to drive the System clock. + - For Low, Medium and High density devices an external 8MHz crystal is + used to drive the System clock. + - For Connectivity line devices an external 25MHz crystal is used to drive + the System clock. + If you are using different crystal you have to adapt those functions accordingly. + */ + +#if defined (STM32F10X_LD_VL) || (defined STM32F10X_MD_VL) || (defined STM32F10X_HD_VL) +/* #define SYSCLK_FREQ_HSE HSE_VALUE */ + #define SYSCLK_FREQ_24MHz 24000000 +#else +/* #define SYSCLK_FREQ_HSE HSE_VALUE */ +/* #define SYSCLK_FREQ_24MHz 24000000 */ +/* #define SYSCLK_FREQ_36MHz 36000000 */ +/* #define SYSCLK_FREQ_48MHz 48000000 */ +/* #define SYSCLK_FREQ_56MHz 56000000 */ +#define SYSCLK_FREQ_72MHz 72000000 +#endif + +/*!< Uncomment the following line if you need to use external SRAM mounted + on STM3210E-EVAL board (STM32 High density and XL-density devices) or on + STM32100E-EVAL board (STM32 High-density value line devices) as data memory */ +#if defined (STM32F10X_HD) || (defined STM32F10X_XL) || (defined STM32F10X_HD_VL) +/* #define DATA_IN_ExtSRAM */ +#endif + +/*!< Uncomment the following line if you need to relocate your vector Table in + Internal SRAM. */ +/* #define VECT_TAB_SRAM */ +#define VECT_TAB_OFFSET 0x0 /*!< Vector Table base offset field. + This value must be a multiple of 0x200. */ + + +/** + * @} + */ + +/** @addtogroup STM32F10x_System_Private_Macros + * @{ + */ + +/** + * @} + */ + +/** @addtogroup STM32F10x_System_Private_Variables + * @{ + */ + +/******************************************************************************* +* Clock Definitions +*******************************************************************************/ +#ifdef SYSCLK_FREQ_HSE + uint32_t SystemCoreClock = SYSCLK_FREQ_HSE; /*!< System Clock Frequency (Core Clock) */ +#elif defined SYSCLK_FREQ_24MHz + uint32_t SystemCoreClock = SYSCLK_FREQ_24MHz; /*!< System Clock Frequency (Core Clock) */ +#elif defined SYSCLK_FREQ_36MHz + uint32_t SystemCoreClock = SYSCLK_FREQ_36MHz; /*!< System Clock Frequency (Core Clock) */ +#elif defined SYSCLK_FREQ_48MHz + uint32_t SystemCoreClock = SYSCLK_FREQ_48MHz; /*!< System Clock Frequency (Core Clock) */ +#elif defined SYSCLK_FREQ_56MHz + uint32_t SystemCoreClock = SYSCLK_FREQ_56MHz; /*!< System Clock Frequency (Core Clock) */ +#elif defined SYSCLK_FREQ_72MHz + uint32_t SystemCoreClock = SYSCLK_FREQ_72MHz; /*!< System Clock Frequency (Core Clock) */ +#else /*!< HSI Selected as System Clock source */ + uint32_t SystemCoreClock = HSI_VALUE; /*!< System Clock Frequency (Core Clock) */ +#endif + +__I uint8_t AHBPrescTable[16] = {0, 0, 0, 0, 0, 0, 0, 0, 1, 2, 3, 4, 6, 7, 8, 9}; +/** + * @} + */ + +/** @addtogroup STM32F10x_System_Private_FunctionPrototypes + * @{ + */ + +static void SetSysClock(void); + +#ifdef SYSCLK_FREQ_HSE + static void SetSysClockToHSE(void); +#elif defined SYSCLK_FREQ_24MHz + static void SetSysClockTo24(void); +#elif defined SYSCLK_FREQ_36MHz + static void SetSysClockTo36(void); +#elif defined SYSCLK_FREQ_48MHz + static void SetSysClockTo48(void); +#elif defined SYSCLK_FREQ_56MHz + static void SetSysClockTo56(void); +#elif defined SYSCLK_FREQ_72MHz + static void SetSysClockTo72(void); +#endif + +#ifdef DATA_IN_ExtSRAM + static void SystemInit_ExtMemCtl(void); +#endif /* DATA_IN_ExtSRAM */ + +/** + * @} + */ + +/** @addtogroup STM32F10x_System_Private_Functions + * @{ + */ + +/** + * @brief Setup the microcontroller system + * Initialize the Embedded Flash Interface, the PLL and update the + * SystemCoreClock variable. + * @note This function should be used only after reset. + * @param None + * @retval None + */ +void SystemInit (void) +{ + /* Reset the RCC clock configuration to the default reset state(for debug purpose) */ + /* Set HSION bit */ + RCC->CR |= (uint32_t)0x00000001; + + /* Reset SW, HPRE, PPRE1, PPRE2, ADCPRE and MCO bits */ +#ifndef STM32F10X_CL + RCC->CFGR &= (uint32_t)0xF8FF0000; +#else + RCC->CFGR &= (uint32_t)0xF0FF0000; +#endif /* STM32F10X_CL */ + + /* Reset HSEON, CSSON and PLLON bits */ + RCC->CR &= (uint32_t)0xFEF6FFFF; + + /* Reset HSEBYP bit */ + RCC->CR &= (uint32_t)0xFFFBFFFF; + + /* Reset PLLSRC, PLLXTPRE, PLLMUL and USBPRE/OTGFSPRE bits */ + RCC->CFGR &= (uint32_t)0xFF80FFFF; + +#ifdef STM32F10X_CL + /* Reset PLL2ON and PLL3ON bits */ + RCC->CR &= (uint32_t)0xEBFFFFFF; + + /* Disable all interrupts and clear pending bits */ + RCC->CIR = 0x00FF0000; + + /* Reset CFGR2 register */ + RCC->CFGR2 = 0x00000000; +#elif defined (STM32F10X_LD_VL) || defined (STM32F10X_MD_VL) || (defined STM32F10X_HD_VL) + /* Disable all interrupts and clear pending bits */ + RCC->CIR = 0x009F0000; + + /* Reset CFGR2 register */ + RCC->CFGR2 = 0x00000000; +#else + /* Disable all interrupts and clear pending bits */ + RCC->CIR = 0x009F0000; +#endif /* STM32F10X_CL */ + +#if defined (STM32F10X_HD) || (defined STM32F10X_XL) || (defined STM32F10X_HD_VL) + #ifdef DATA_IN_ExtSRAM + SystemInit_ExtMemCtl(); + #endif /* DATA_IN_ExtSRAM */ +#endif + + /* Configure the System clock frequency, HCLK, PCLK2 and PCLK1 prescalers */ + /* Configure the Flash Latency cycles and enable prefetch buffer */ + SetSysClock(); + +#ifdef VECT_TAB_SRAM + SCB->VTOR = SRAM_BASE | VECT_TAB_OFFSET; /* Vector Table Relocation in Internal SRAM. */ +#else + SCB->VTOR = FLASH_BASE | VECT_TAB_OFFSET; /* Vector Table Relocation in Internal FLASH. */ +#endif +} + +/** + * @brief Update SystemCoreClock variable according to Clock Register Values. + * The SystemCoreClock variable contains the core clock (HCLK), it can + * be used by the user application to setup the SysTick timer or configure + * other parameters. + * + * @note Each time the core clock (HCLK) changes, this function must be called + * to update SystemCoreClock variable value. Otherwise, any configuration + * based on this variable will be incorrect. + * + * @note - The system frequency computed by this function is not the real + * frequency in the chip. It is calculated based on the predefined + * constant and the selected clock source: + * + * - If SYSCLK source is HSI, SystemCoreClock will contain the HSI_VALUE(*) + * + * - If SYSCLK source is HSE, SystemCoreClock will contain the HSE_VALUE(**) + * + * - If SYSCLK source is PLL, SystemCoreClock will contain the HSE_VALUE(**) + * or HSI_VALUE(*) multiplied by the PLL factors. + * + * (*) HSI_VALUE is a constant defined in stm32f1xx.h file (default value + * 8 MHz) but the real value may vary depending on the variations + * in voltage and temperature. + * + * (**) HSE_VALUE is a constant defined in stm32f1xx.h file (default value + * 8 MHz or 25 MHz, depedning on the product used), user has to ensure + * that HSE_VALUE is same as the real frequency of the crystal used. + * Otherwise, this function may have wrong result. + * + * - The result of this function could be not correct when using fractional + * value for HSE crystal. + * @param None + * @retval None + */ +void SystemCoreClockUpdate (void) +{ + uint32_t tmp = 0, pllmull = 0, pllsource = 0; + +#ifdef STM32F10X_CL + uint32_t prediv1source = 0, prediv1factor = 0, prediv2factor = 0, pll2mull = 0; +#endif /* STM32F10X_CL */ + +#if defined (STM32F10X_LD_VL) || defined (STM32F10X_MD_VL) || (defined STM32F10X_HD_VL) + uint32_t prediv1factor = 0; +#endif /* STM32F10X_LD_VL or STM32F10X_MD_VL or STM32F10X_HD_VL */ + + /* Get SYSCLK source -------------------------------------------------------*/ + tmp = RCC->CFGR & RCC_CFGR_SWS; + + switch (tmp) + { + case 0x00: /* HSI used as system clock */ + SystemCoreClock = HSI_VALUE; + break; + case 0x04: /* HSE used as system clock */ + SystemCoreClock = HSE_VALUE; + break; + case 0x08: /* PLL used as system clock */ + + /* Get PLL clock source and multiplication factor ----------------------*/ + pllmull = RCC->CFGR & RCC_CFGR_PLLMULL; + pllsource = RCC->CFGR & RCC_CFGR_PLLSRC; + +#ifndef STM32F10X_CL + pllmull = ( pllmull >> 18) + 2; + + if (pllsource == 0x00) + { + /* HSI oscillator clock divided by 2 selected as PLL clock entry */ + SystemCoreClock = (HSI_VALUE >> 1) * pllmull; + } + else + { + #if defined (STM32F10X_LD_VL) || defined (STM32F10X_MD_VL) || (defined STM32F10X_HD_VL) + prediv1factor = (RCC->CFGR2 & RCC_CFGR2_PREDIV1) + 1; + /* HSE oscillator clock selected as PREDIV1 clock entry */ + SystemCoreClock = (HSE_VALUE / prediv1factor) * pllmull; + #else + /* HSE selected as PLL clock entry */ + if ((RCC->CFGR & RCC_CFGR_PLLXTPRE) != (uint32_t)RESET) + {/* HSE oscillator clock divided by 2 */ + SystemCoreClock = (HSE_VALUE >> 1) * pllmull; + } + else + { + SystemCoreClock = HSE_VALUE * pllmull; + } + #endif + } +#else + pllmull = pllmull >> 18; + + if (pllmull != 0x0D) + { + pllmull += 2; + } + else + { /* PLL multiplication factor = PLL input clock * 6.5 */ + pllmull = 13 / 2; + } + + if (pllsource == 0x00) + { + /* HSI oscillator clock divided by 2 selected as PLL clock entry */ + SystemCoreClock = (HSI_VALUE >> 1) * pllmull; + } + else + {/* PREDIV1 selected as PLL clock entry */ + + /* Get PREDIV1 clock source and division factor */ + prediv1source = RCC->CFGR2 & RCC_CFGR2_PREDIV1SRC; + prediv1factor = (RCC->CFGR2 & RCC_CFGR2_PREDIV1) + 1; + + if (prediv1source == 0) + { + /* HSE oscillator clock selected as PREDIV1 clock entry */ + SystemCoreClock = (HSE_VALUE / prediv1factor) * pllmull; + } + else + {/* PLL2 clock selected as PREDIV1 clock entry */ + + /* Get PREDIV2 division factor and PLL2 multiplication factor */ + prediv2factor = ((RCC->CFGR2 & RCC_CFGR2_PREDIV2) >> 4) + 1; + pll2mull = ((RCC->CFGR2 & RCC_CFGR2_PLL2MUL) >> 8 ) + 2; + SystemCoreClock = (((HSE_VALUE / prediv2factor) * pll2mull) / prediv1factor) * pllmull; + } + } +#endif /* STM32F10X_CL */ + break; + + default: + SystemCoreClock = HSI_VALUE; + break; + } + + /* Compute HCLK clock frequency ----------------*/ + /* Get HCLK prescaler */ + tmp = AHBPrescTable[((RCC->CFGR & RCC_CFGR_HPRE) >> 4)]; + /* HCLK clock frequency */ + SystemCoreClock >>= tmp; +} + +/** + * @brief Configures the System clock frequency, HCLK, PCLK2 and PCLK1 prescalers. + * @param None + * @retval None + */ +static void SetSysClock(void) +{ +#ifdef SYSCLK_FREQ_HSE + SetSysClockToHSE(); +#elif defined SYSCLK_FREQ_24MHz + SetSysClockTo24(); +#elif defined SYSCLK_FREQ_36MHz + SetSysClockTo36(); +#elif defined SYSCLK_FREQ_48MHz + SetSysClockTo48(); +#elif defined SYSCLK_FREQ_56MHz + SetSysClockTo56(); +#elif defined SYSCLK_FREQ_72MHz + SetSysClockTo72(); +#endif + + /* If none of the define above is enabled, the HSI is used as System clock + source (default after reset) */ +} + +/** + * @brief Setup the external memory controller. Called in startup_stm32f10x.s + * before jump to __main + * @param None + * @retval None + */ +#ifdef DATA_IN_ExtSRAM +/** + * @brief Setup the external memory controller. + * Called in startup_stm32f10x_xx.s/.c before jump to main. + * This function configures the external SRAM mounted on STM3210E-EVAL + * board (STM32 High density devices). This SRAM will be used as program + * data memory (including heap and stack). + * @param None + * @retval None + */ +void SystemInit_ExtMemCtl(void) +{ +/*!< FSMC Bank1 NOR/SRAM3 is used for the STM3210E-EVAL, if another Bank is + required, then adjust the Register Addresses */ + + /* Enable FSMC clock */ + RCC->AHBENR = 0x00000114; + + /* Enable GPIOD, GPIOE, GPIOF and GPIOG clocks */ + RCC->APB2ENR = 0x000001E0; + +/* --------------- SRAM Data lines, NOE and NWE configuration ---------------*/ +/*---------------- SRAM Address lines configuration -------------------------*/ +/*---------------- NOE and NWE configuration --------------------------------*/ +/*---------------- NE3 configuration ----------------------------------------*/ +/*---------------- NBL0, NBL1 configuration ---------------------------------*/ + + GPIOD->CRL = 0x44BB44BB; + GPIOD->CRH = 0xBBBBBBBB; + + GPIOE->CRL = 0xB44444BB; + GPIOE->CRH = 0xBBBBBBBB; + + GPIOF->CRL = 0x44BBBBBB; + GPIOF->CRH = 0xBBBB4444; + + GPIOG->CRL = 0x44BBBBBB; + GPIOG->CRH = 0x44444B44; + +/*---------------- FSMC Configuration ---------------------------------------*/ +/*---------------- Enable FSMC Bank1_SRAM Bank ------------------------------*/ + + FSMC_Bank1->BTCR[4] = 0x00001011; + FSMC_Bank1->BTCR[5] = 0x00000200; +} +#endif /* DATA_IN_ExtSRAM */ + +#ifdef SYSCLK_FREQ_HSE +/** + * @brief Selects HSE as System clock source and configure HCLK, PCLK2 + * and PCLK1 prescalers. + * @note This function should be used only after reset. + * @param None + * @retval None + */ +static void SetSysClockToHSE(void) +{ + __IO uint32_t StartUpCounter = 0, HSEStatus = 0; + + /* SYSCLK, HCLK, PCLK2 and PCLK1 configuration ---------------------------*/ + /* Enable HSE */ + RCC->CR |= ((uint32_t)RCC_CR_HSEON); + + /* Wait till HSE is ready and if Time out is reached exit */ + do + { + HSEStatus = RCC->CR & RCC_CR_HSERDY; + StartUpCounter++; + } while((HSEStatus == 0) && (StartUpCounter != HSE_STARTUP_TIMEOUT)); + + if ((RCC->CR & RCC_CR_HSERDY) != RESET) + { + HSEStatus = (uint32_t)0x01; + } + else + { + HSEStatus = (uint32_t)0x00; + } + + if (HSEStatus == (uint32_t)0x01) + { + +#if !defined STM32F10X_LD_VL && !defined STM32F10X_MD_VL && !defined STM32F10X_HD_VL + /* Enable Prefetch Buffer */ + FLASH->ACR |= FLASH_ACR_PRFTBE; + + /* Flash 0 wait state */ + FLASH->ACR &= (uint32_t)((uint32_t)~FLASH_ACR_LATENCY); + +#ifndef STM32F10X_CL + FLASH->ACR |= (uint32_t)FLASH_ACR_LATENCY_0; +#else + if (HSE_VALUE <= 24000000) + { + FLASH->ACR |= (uint32_t)FLASH_ACR_LATENCY_0; + } + else + { + FLASH->ACR |= (uint32_t)FLASH_ACR_LATENCY_1; + } +#endif /* STM32F10X_CL */ +#endif + + /* HCLK = SYSCLK */ + RCC->CFGR |= (uint32_t)RCC_CFGR_HPRE_DIV1; + + /* PCLK2 = HCLK */ + RCC->CFGR |= (uint32_t)RCC_CFGR_PPRE2_DIV1; + + /* PCLK1 = HCLK */ + RCC->CFGR |= (uint32_t)RCC_CFGR_PPRE1_DIV1; + + /* Select HSE as system clock source */ + RCC->CFGR &= (uint32_t)((uint32_t)~(RCC_CFGR_SW)); + RCC->CFGR |= (uint32_t)RCC_CFGR_SW_HSE; + + /* Wait till HSE is used as system clock source */ + while ((RCC->CFGR & (uint32_t)RCC_CFGR_SWS) != (uint32_t)0x04) + { + } + } + else + { /* If HSE fails to start-up, the application will have wrong clock + configuration. User can add here some code to deal with this error */ + } +} +#elif defined SYSCLK_FREQ_24MHz +/** + * @brief Sets System clock frequency to 24MHz and configure HCLK, PCLK2 + * and PCLK1 prescalers. + * @note This function should be used only after reset. + * @param None + * @retval None + */ +static void SetSysClockTo24(void) +{ + __IO uint32_t StartUpCounter = 0, HSEStatus = 0; + + /* SYSCLK, HCLK, PCLK2 and PCLK1 configuration ---------------------------*/ + /* Enable HSE */ + RCC->CR |= ((uint32_t)RCC_CR_HSEON); + + /* Wait till HSE is ready and if Time out is reached exit */ + do + { + HSEStatus = RCC->CR & RCC_CR_HSERDY; + StartUpCounter++; + } while((HSEStatus == 0) && (StartUpCounter != HSE_STARTUP_TIMEOUT)); + + if ((RCC->CR & RCC_CR_HSERDY) != RESET) + { + HSEStatus = (uint32_t)0x01; + } + else + { + HSEStatus = (uint32_t)0x00; + } + + if (HSEStatus == (uint32_t)0x01) + { +#if !defined STM32F10X_LD_VL && !defined STM32F10X_MD_VL && !defined STM32F10X_HD_VL + /* Enable Prefetch Buffer */ + FLASH->ACR |= FLASH_ACR_PRFTBE; + + /* Flash 0 wait state */ + FLASH->ACR &= (uint32_t)((uint32_t)~FLASH_ACR_LATENCY); + FLASH->ACR |= (uint32_t)FLASH_ACR_LATENCY_0; +#endif + + /* HCLK = SYSCLK */ + RCC->CFGR |= (uint32_t)RCC_CFGR_HPRE_DIV1; + + /* PCLK2 = HCLK */ + RCC->CFGR |= (uint32_t)RCC_CFGR_PPRE2_DIV1; + + /* PCLK1 = HCLK */ + RCC->CFGR |= (uint32_t)RCC_CFGR_PPRE1_DIV1; + +#ifdef STM32F10X_CL + /* Configure PLLs ------------------------------------------------------*/ + /* PLL configuration: PLLCLK = PREDIV1 * 6 = 24 MHz */ + RCC->CFGR &= (uint32_t)~(RCC_CFGR_PLLXTPRE | RCC_CFGR_PLLSRC | RCC_CFGR_PLLMULL); + RCC->CFGR |= (uint32_t)(RCC_CFGR_PLLXTPRE_PREDIV1 | RCC_CFGR_PLLSRC_PREDIV1 | + RCC_CFGR_PLLMULL6); + + /* PLL2 configuration: PLL2CLK = (HSE / 5) * 8 = 40 MHz */ + /* PREDIV1 configuration: PREDIV1CLK = PLL2 / 10 = 4 MHz */ + RCC->CFGR2 &= (uint32_t)~(RCC_CFGR2_PREDIV2 | RCC_CFGR2_PLL2MUL | + RCC_CFGR2_PREDIV1 | RCC_CFGR2_PREDIV1SRC); + RCC->CFGR2 |= (uint32_t)(RCC_CFGR2_PREDIV2_DIV5 | RCC_CFGR2_PLL2MUL8 | + RCC_CFGR2_PREDIV1SRC_PLL2 | RCC_CFGR2_PREDIV1_DIV10); + + /* Enable PLL2 */ + RCC->CR |= RCC_CR_PLL2ON; + /* Wait till PLL2 is ready */ + while((RCC->CR & RCC_CR_PLL2RDY) == 0) + { + } +#elif defined (STM32F10X_LD_VL) || defined (STM32F10X_MD_VL) || defined (STM32F10X_HD_VL) + /* PLL configuration: = (HSE / 2) * 6 = 24 MHz */ + RCC->CFGR &= (uint32_t)((uint32_t)~(RCC_CFGR_PLLSRC | RCC_CFGR_PLLXTPRE | RCC_CFGR_PLLMULL)); + RCC->CFGR |= (uint32_t)(RCC_CFGR_PLLSRC_PREDIV1 | RCC_CFGR_PLLXTPRE_PREDIV1_Div2 | RCC_CFGR_PLLMULL6); +#else + /* PLL configuration: = (HSE / 2) * 6 = 24 MHz */ + RCC->CFGR &= (uint32_t)((uint32_t)~(RCC_CFGR_PLLSRC | RCC_CFGR_PLLXTPRE | RCC_CFGR_PLLMULL)); + RCC->CFGR |= (uint32_t)(RCC_CFGR_PLLSRC_HSE | RCC_CFGR_PLLXTPRE_HSE_Div2 | RCC_CFGR_PLLMULL6); +#endif /* STM32F10X_CL */ + + /* Enable PLL */ + RCC->CR |= RCC_CR_PLLON; + + /* Wait till PLL is ready */ + while((RCC->CR & RCC_CR_PLLRDY) == 0) + { + } + + /* Select PLL as system clock source */ + RCC->CFGR &= (uint32_t)((uint32_t)~(RCC_CFGR_SW)); + RCC->CFGR |= (uint32_t)RCC_CFGR_SW_PLL; + + /* Wait till PLL is used as system clock source */ + while ((RCC->CFGR & (uint32_t)RCC_CFGR_SWS) != (uint32_t)0x08) + { + } + } + else + { /* If HSE fails to start-up, the application will have wrong clock + configuration. User can add here some code to deal with this error */ + } +} +#elif defined SYSCLK_FREQ_36MHz +/** + * @brief Sets System clock frequency to 36MHz and configure HCLK, PCLK2 + * and PCLK1 prescalers. + * @note This function should be used only after reset. + * @param None + * @retval None + */ +static void SetSysClockTo36(void) +{ + __IO uint32_t StartUpCounter = 0, HSEStatus = 0; + + /* SYSCLK, HCLK, PCLK2 and PCLK1 configuration ---------------------------*/ + /* Enable HSE */ + RCC->CR |= ((uint32_t)RCC_CR_HSEON); + + /* Wait till HSE is ready and if Time out is reached exit */ + do + { + HSEStatus = RCC->CR & RCC_CR_HSERDY; + StartUpCounter++; + } while((HSEStatus == 0) && (StartUpCounter != HSE_STARTUP_TIMEOUT)); + + if ((RCC->CR & RCC_CR_HSERDY) != RESET) + { + HSEStatus = (uint32_t)0x01; + } + else + { + HSEStatus = (uint32_t)0x00; + } + + if (HSEStatus == (uint32_t)0x01) + { + /* Enable Prefetch Buffer */ + FLASH->ACR |= FLASH_ACR_PRFTBE; + + /* Flash 1 wait state */ + FLASH->ACR &= (uint32_t)((uint32_t)~FLASH_ACR_LATENCY); + FLASH->ACR |= (uint32_t)FLASH_ACR_LATENCY_1; + + /* HCLK = SYSCLK */ + RCC->CFGR |= (uint32_t)RCC_CFGR_HPRE_DIV1; + + /* PCLK2 = HCLK */ + RCC->CFGR |= (uint32_t)RCC_CFGR_PPRE2_DIV1; + + /* PCLK1 = HCLK */ + RCC->CFGR |= (uint32_t)RCC_CFGR_PPRE1_DIV1; + +#ifdef STM32F10X_CL + /* Configure PLLs ------------------------------------------------------*/ + + /* PLL configuration: PLLCLK = PREDIV1 * 9 = 36 MHz */ + RCC->CFGR &= (uint32_t)~(RCC_CFGR_PLLXTPRE | RCC_CFGR_PLLSRC | RCC_CFGR_PLLMULL); + RCC->CFGR |= (uint32_t)(RCC_CFGR_PLLXTPRE_PREDIV1 | RCC_CFGR_PLLSRC_PREDIV1 | + RCC_CFGR_PLLMULL9); + + /*!< PLL2 configuration: PLL2CLK = (HSE / 5) * 8 = 40 MHz */ + /* PREDIV1 configuration: PREDIV1CLK = PLL2 / 10 = 4 MHz */ + + RCC->CFGR2 &= (uint32_t)~(RCC_CFGR2_PREDIV2 | RCC_CFGR2_PLL2MUL | + RCC_CFGR2_PREDIV1 | RCC_CFGR2_PREDIV1SRC); + RCC->CFGR2 |= (uint32_t)(RCC_CFGR2_PREDIV2_DIV5 | RCC_CFGR2_PLL2MUL8 | + RCC_CFGR2_PREDIV1SRC_PLL2 | RCC_CFGR2_PREDIV1_DIV10); + + /* Enable PLL2 */ + RCC->CR |= RCC_CR_PLL2ON; + /* Wait till PLL2 is ready */ + while((RCC->CR & RCC_CR_PLL2RDY) == 0) + { + } + +#else + /* PLL configuration: PLLCLK = (HSE / 2) * 9 = 36 MHz */ + RCC->CFGR &= (uint32_t)((uint32_t)~(RCC_CFGR_PLLSRC | RCC_CFGR_PLLXTPRE | RCC_CFGR_PLLMULL)); + RCC->CFGR |= (uint32_t)(RCC_CFGR_PLLSRC_HSE | RCC_CFGR_PLLXTPRE_HSE_Div2 | RCC_CFGR_PLLMULL9); +#endif /* STM32F10X_CL */ + + /* Enable PLL */ + RCC->CR |= RCC_CR_PLLON; + + /* Wait till PLL is ready */ + while((RCC->CR & RCC_CR_PLLRDY) == 0) + { + } + + /* Select PLL as system clock source */ + RCC->CFGR &= (uint32_t)((uint32_t)~(RCC_CFGR_SW)); + RCC->CFGR |= (uint32_t)RCC_CFGR_SW_PLL; + + /* Wait till PLL is used as system clock source */ + while ((RCC->CFGR & (uint32_t)RCC_CFGR_SWS) != (uint32_t)0x08) + { + } + } + else + { /* If HSE fails to start-up, the application will have wrong clock + configuration. User can add here some code to deal with this error */ + } +} +#elif defined SYSCLK_FREQ_48MHz +/** + * @brief Sets System clock frequency to 48MHz and configure HCLK, PCLK2 + * and PCLK1 prescalers. + * @note This function should be used only after reset. + * @param None + * @retval None + */ +static void SetSysClockTo48(void) +{ + __IO uint32_t StartUpCounter = 0, HSEStatus = 0; + + /* SYSCLK, HCLK, PCLK2 and PCLK1 configuration ---------------------------*/ + /* Enable HSE */ + RCC->CR |= ((uint32_t)RCC_CR_HSEON); + + /* Wait till HSE is ready and if Time out is reached exit */ + do + { + HSEStatus = RCC->CR & RCC_CR_HSERDY; + StartUpCounter++; + } while((HSEStatus == 0) && (StartUpCounter != HSE_STARTUP_TIMEOUT)); + + if ((RCC->CR & RCC_CR_HSERDY) != RESET) + { + HSEStatus = (uint32_t)0x01; + } + else + { + HSEStatus = (uint32_t)0x00; + } + + if (HSEStatus == (uint32_t)0x01) + { + /* Enable Prefetch Buffer */ + FLASH->ACR |= FLASH_ACR_PRFTBE; + + /* Flash 1 wait state */ + FLASH->ACR &= (uint32_t)((uint32_t)~FLASH_ACR_LATENCY); + FLASH->ACR |= (uint32_t)FLASH_ACR_LATENCY_1; + + /* HCLK = SYSCLK */ + RCC->CFGR |= (uint32_t)RCC_CFGR_HPRE_DIV1; + + /* PCLK2 = HCLK */ + RCC->CFGR |= (uint32_t)RCC_CFGR_PPRE2_DIV1; + + /* PCLK1 = HCLK */ + RCC->CFGR |= (uint32_t)RCC_CFGR_PPRE1_DIV2; + +#ifdef STM32F10X_CL + /* Configure PLLs ------------------------------------------------------*/ + /* PLL2 configuration: PLL2CLK = (HSE / 5) * 8 = 40 MHz */ + /* PREDIV1 configuration: PREDIV1CLK = PLL2 / 5 = 8 MHz */ + + RCC->CFGR2 &= (uint32_t)~(RCC_CFGR2_PREDIV2 | RCC_CFGR2_PLL2MUL | + RCC_CFGR2_PREDIV1 | RCC_CFGR2_PREDIV1SRC); + RCC->CFGR2 |= (uint32_t)(RCC_CFGR2_PREDIV2_DIV5 | RCC_CFGR2_PLL2MUL8 | + RCC_CFGR2_PREDIV1SRC_PLL2 | RCC_CFGR2_PREDIV1_DIV5); + + /* Enable PLL2 */ + RCC->CR |= RCC_CR_PLL2ON; + /* Wait till PLL2 is ready */ + while((RCC->CR & RCC_CR_PLL2RDY) == 0) + { + } + + + /* PLL configuration: PLLCLK = PREDIV1 * 6 = 48 MHz */ + RCC->CFGR &= (uint32_t)~(RCC_CFGR_PLLXTPRE | RCC_CFGR_PLLSRC | RCC_CFGR_PLLMULL); + RCC->CFGR |= (uint32_t)(RCC_CFGR_PLLXTPRE_PREDIV1 | RCC_CFGR_PLLSRC_PREDIV1 | + RCC_CFGR_PLLMULL6); +#else + /* PLL configuration: PLLCLK = HSE * 6 = 48 MHz */ + RCC->CFGR &= (uint32_t)((uint32_t)~(RCC_CFGR_PLLSRC | RCC_CFGR_PLLXTPRE | RCC_CFGR_PLLMULL)); + RCC->CFGR |= (uint32_t)(RCC_CFGR_PLLSRC_HSE | RCC_CFGR_PLLMULL6); +#endif /* STM32F10X_CL */ + + /* Enable PLL */ + RCC->CR |= RCC_CR_PLLON; + + /* Wait till PLL is ready */ + while((RCC->CR & RCC_CR_PLLRDY) == 0) + { + } + + /* Select PLL as system clock source */ + RCC->CFGR &= (uint32_t)((uint32_t)~(RCC_CFGR_SW)); + RCC->CFGR |= (uint32_t)RCC_CFGR_SW_PLL; + + /* Wait till PLL is used as system clock source */ + while ((RCC->CFGR & (uint32_t)RCC_CFGR_SWS) != (uint32_t)0x08) + { + } + } + else + { /* If HSE fails to start-up, the application will have wrong clock + configuration. User can add here some code to deal with this error */ + } +} + +#elif defined SYSCLK_FREQ_56MHz +/** + * @brief Sets System clock frequency to 56MHz and configure HCLK, PCLK2 + * and PCLK1 prescalers. + * @note This function should be used only after reset. + * @param None + * @retval None + */ +static void SetSysClockTo56(void) +{ + __IO uint32_t StartUpCounter = 0, HSEStatus = 0; + + /* SYSCLK, HCLK, PCLK2 and PCLK1 configuration ---------------------------*/ + /* Enable HSE */ + RCC->CR |= ((uint32_t)RCC_CR_HSEON); + + /* Wait till HSE is ready and if Time out is reached exit */ + do + { + HSEStatus = RCC->CR & RCC_CR_HSERDY; + StartUpCounter++; + } while((HSEStatus == 0) && (StartUpCounter != HSE_STARTUP_TIMEOUT)); + + if ((RCC->CR & RCC_CR_HSERDY) != RESET) + { + HSEStatus = (uint32_t)0x01; + } + else + { + HSEStatus = (uint32_t)0x00; + } + + if (HSEStatus == (uint32_t)0x01) + { + /* Enable Prefetch Buffer */ + FLASH->ACR |= FLASH_ACR_PRFTBE; + + /* Flash 2 wait state */ + FLASH->ACR &= (uint32_t)((uint32_t)~FLASH_ACR_LATENCY); + FLASH->ACR |= (uint32_t)FLASH_ACR_LATENCY_2; + + /* HCLK = SYSCLK */ + RCC->CFGR |= (uint32_t)RCC_CFGR_HPRE_DIV1; + + /* PCLK2 = HCLK */ + RCC->CFGR |= (uint32_t)RCC_CFGR_PPRE2_DIV1; + + /* PCLK1 = HCLK */ + RCC->CFGR |= (uint32_t)RCC_CFGR_PPRE1_DIV2; + +#ifdef STM32F10X_CL + /* Configure PLLs ------------------------------------------------------*/ + /* PLL2 configuration: PLL2CLK = (HSE / 5) * 8 = 40 MHz */ + /* PREDIV1 configuration: PREDIV1CLK = PLL2 / 5 = 8 MHz */ + + RCC->CFGR2 &= (uint32_t)~(RCC_CFGR2_PREDIV2 | RCC_CFGR2_PLL2MUL | + RCC_CFGR2_PREDIV1 | RCC_CFGR2_PREDIV1SRC); + RCC->CFGR2 |= (uint32_t)(RCC_CFGR2_PREDIV2_DIV5 | RCC_CFGR2_PLL2MUL8 | + RCC_CFGR2_PREDIV1SRC_PLL2 | RCC_CFGR2_PREDIV1_DIV5); + + /* Enable PLL2 */ + RCC->CR |= RCC_CR_PLL2ON; + /* Wait till PLL2 is ready */ + while((RCC->CR & RCC_CR_PLL2RDY) == 0) + { + } + + + /* PLL configuration: PLLCLK = PREDIV1 * 7 = 56 MHz */ + RCC->CFGR &= (uint32_t)~(RCC_CFGR_PLLXTPRE | RCC_CFGR_PLLSRC | RCC_CFGR_PLLMULL); + RCC->CFGR |= (uint32_t)(RCC_CFGR_PLLXTPRE_PREDIV1 | RCC_CFGR_PLLSRC_PREDIV1 | + RCC_CFGR_PLLMULL7); +#else + /* PLL configuration: PLLCLK = HSE * 7 = 56 MHz */ + RCC->CFGR &= (uint32_t)((uint32_t)~(RCC_CFGR_PLLSRC | RCC_CFGR_PLLXTPRE | RCC_CFGR_PLLMULL)); + RCC->CFGR |= (uint32_t)(RCC_CFGR_PLLSRC_HSE | RCC_CFGR_PLLMULL7); + +#endif /* STM32F10X_CL */ + + /* Enable PLL */ + RCC->CR |= RCC_CR_PLLON; + + /* Wait till PLL is ready */ + while((RCC->CR & RCC_CR_PLLRDY) == 0) + { + } + + /* Select PLL as system clock source */ + RCC->CFGR &= (uint32_t)((uint32_t)~(RCC_CFGR_SW)); + RCC->CFGR |= (uint32_t)RCC_CFGR_SW_PLL; + + /* Wait till PLL is used as system clock source */ + while ((RCC->CFGR & (uint32_t)RCC_CFGR_SWS) != (uint32_t)0x08) + { + } + } + else + { /* If HSE fails to start-up, the application will have wrong clock + configuration. User can add here some code to deal with this error */ + } +} + +#elif defined SYSCLK_FREQ_72MHz +/** + * @brief Sets System clock frequency to 72MHz and configure HCLK, PCLK2 + * and PCLK1 prescalers. + * @note This function should be used only after reset. + * @param None + * @retval None + */ +static void SetSysClockTo72(void) +{ + __IO uint32_t StartUpCounter = 0, HSEStatus = 0; + + /* SYSCLK, HCLK, PCLK2 and PCLK1 configuration ---------------------------*/ + /* Enable HSE */ + RCC->CR |= ((uint32_t)RCC_CR_HSEON); + + /* Wait till HSE is ready and if Time out is reached exit */ + do + { + HSEStatus = RCC->CR & RCC_CR_HSERDY; + StartUpCounter++; + } while((HSEStatus == 0) && (StartUpCounter != HSE_STARTUP_TIMEOUT)); + + if ((RCC->CR & RCC_CR_HSERDY) != RESET) + { + HSEStatus = (uint32_t)0x01; + } + else + { + HSEStatus = (uint32_t)0x00; + } + + if (HSEStatus == (uint32_t)0x01) + { + /* Enable Prefetch Buffer */ + FLASH->ACR |= FLASH_ACR_PRFTBE; + + /* Flash 2 wait state */ + FLASH->ACR &= (uint32_t)((uint32_t)~FLASH_ACR_LATENCY); + FLASH->ACR |= (uint32_t)FLASH_ACR_LATENCY_2; + + + /* HCLK = SYSCLK */ + RCC->CFGR |= (uint32_t)RCC_CFGR_HPRE_DIV1; + + /* PCLK2 = HCLK */ + RCC->CFGR |= (uint32_t)RCC_CFGR_PPRE2_DIV1; + + /* PCLK1 = HCLK */ + RCC->CFGR |= (uint32_t)RCC_CFGR_PPRE1_DIV2; + +#ifdef STM32F10X_CL + /* Configure PLLs ------------------------------------------------------*/ + /* PLL2 configuration: PLL2CLK = (HSE / 5) * 8 = 40 MHz */ + /* PREDIV1 configuration: PREDIV1CLK = PLL2 / 5 = 8 MHz */ + + RCC->CFGR2 &= (uint32_t)~(RCC_CFGR2_PREDIV2 | RCC_CFGR2_PLL2MUL | + RCC_CFGR2_PREDIV1 | RCC_CFGR2_PREDIV1SRC); + RCC->CFGR2 |= (uint32_t)(RCC_CFGR2_PREDIV2_DIV5 | RCC_CFGR2_PLL2MUL8 | + RCC_CFGR2_PREDIV1SRC_PLL2 | RCC_CFGR2_PREDIV1_DIV5); + + /* Enable PLL2 */ + RCC->CR |= RCC_CR_PLL2ON; + /* Wait till PLL2 is ready */ + while((RCC->CR & RCC_CR_PLL2RDY) == 0) + { + } + + + /* PLL configuration: PLLCLK = PREDIV1 * 9 = 72 MHz */ + RCC->CFGR &= (uint32_t)~(RCC_CFGR_PLLXTPRE | RCC_CFGR_PLLSRC | RCC_CFGR_PLLMULL); + RCC->CFGR |= (uint32_t)(RCC_CFGR_PLLXTPRE_PREDIV1 | RCC_CFGR_PLLSRC_PREDIV1 | + RCC_CFGR_PLLMULL9); +#else + /* PLL configuration: PLLCLK = HSE * 9 = 72 MHz */ + RCC->CFGR &= (uint32_t)((uint32_t)~(RCC_CFGR_PLLSRC | RCC_CFGR_PLLXTPRE | + RCC_CFGR_PLLMULL)); + RCC->CFGR |= (uint32_t)(RCC_CFGR_PLLSRC_HSE | RCC_CFGR_PLLMULL9); +#endif /* STM32F10X_CL */ + + /* Enable PLL */ + RCC->CR |= RCC_CR_PLLON; + + /* Wait till PLL is ready */ + while((RCC->CR & RCC_CR_PLLRDY) == 0) + { + } + + /* Select PLL as system clock source */ + RCC->CFGR &= (uint32_t)((uint32_t)~(RCC_CFGR_SW)); + RCC->CFGR |= (uint32_t)RCC_CFGR_SW_PLL; + + /* Wait till PLL is used as system clock source */ + while ((RCC->CFGR & (uint32_t)RCC_CFGR_SWS) != (uint32_t)0x08) + { + } + } + else + { /* If HSE fails to start-up, the application will have wrong clock + configuration. User can add here some code to deal with this error */ + } +} +#endif + +/** + * @} + */ + +/** + * @} + */ + +/** + * @} + */ +/******************* (C) COPYRIGHT 2011 STMicroelectronics *****END OF FILE****/ diff --git a/tmp/STM32F10x_StdPeriph_Lib_V3.5.0/Project/STM32F10x_StdPeriph_Examples/DMA/FSMC/main.c b/tmp/STM32F10x_StdPeriph_Lib_V3.5.0/Project/STM32F10x_StdPeriph_Examples/DMA/FSMC/main.c new file mode 100644 index 0000000..d982167 --- /dev/null +++ b/tmp/STM32F10x_StdPeriph_Lib_V3.5.0/Project/STM32F10x_StdPeriph_Examples/DMA/FSMC/main.c @@ -0,0 +1,218 @@ +/** + ****************************************************************************** + * @file DMA/FSMC/main.c + * @author MCD Application Team + * @version V3.5.0 + * @date 08-April-2011 + * @brief Main program body. + ****************************************************************************** + * @attention + * + * THE PRESENT FIRMWARE WHICH IS FOR GUIDANCE ONLY AIMS AT PROVIDING CUSTOMERS + * WITH CODING INFORMATION REGARDING THEIR PRODUCTS IN ORDER FOR THEM TO SAVE + * TIME. AS A RESULT, STMICROELECTRONICS SHALL NOT BE HELD LIABLE FOR ANY + * DIRECT, INDIRECT OR CONSEQUENTIAL DAMAGES WITH RESPECT TO ANY CLAIMS ARISING + * FROM THE CONTENT OF SUCH FIRMWARE AND/OR THE USE MADE BY CUSTOMERS OF THE + * CODING INFORMATION CONTAINED HEREIN IN CONNECTION WITH THEIR PRODUCTS. + * + *

© COPYRIGHT 2011 STMicroelectronics

+ ****************************************************************************** + */ + +/* Includes ------------------------------------------------------------------*/ +#ifdef STM32F10X_HD_VL /* High-density Value line devices */ + #include "stm32100e_eval_fsmc_sram.h" +#else /* High- and XL-density */ + #include "stm3210e_eval_fsmc_sram.h" +#endif + +/** @addtogroup STM32F10x_StdPeriph_Examples + * @{ + */ + +/** @addtogroup DMA_FSMC + * @{ + */ + +/* Private typedef -----------------------------------------------------------*/ +typedef enum {FAILED = 0, PASSED = !FAILED} TestStatus; + +/* Private define ------------------------------------------------------------*/ +#define BufferSize 32 +#define Bank1_SRAM3_ADDR ((uint32_t)0x68000000) + +/* Private macro -------------------------------------------------------------*/ +/* Private variables ---------------------------------------------------------*/ +DMA_InitTypeDef DMA_InitStructure; +volatile TestStatus TransferStatus; +const uint32_t SRC_Const_Buffer[BufferSize]= { + 0x01020304,0x05060708,0x090A0B0C,0x0D0E0F10, + 0x11121314,0x15161718,0x191A1B1C,0x1D1E1F20, + 0x21222324,0x25262728,0x292A2B2C,0x2D2E2F30, + 0x31323334,0x35363738,0x393A3B3C,0x3D3E3F40, + 0x41424344,0x45464748,0x494A4B4C,0x4D4E4F50, + 0x51525354,0x55565758,0x595A5B5C,0x5D5E5F60, + 0x61626364,0x65666768,0x696A6B6C,0x6D6E6F70, + 0x71727374,0x75767778,0x797A7B7C,0x7D7E7F80}; +uint8_t DST_Buffer[4*BufferSize]; +uint32_t Idx = 0; + +/* Private function prototypes -----------------------------------------------*/ +void RCC_Configuration(void); +TestStatus Buffercmp(const uint32_t* pBuffer, uint32_t* pBuffer1, uint16_t BufferLength); + +/* Private functions ---------------------------------------------------------*/ + +/** + * @brief Main program. + * @param None + * @retval None + */ +int main(void) +{ + /*!< At this stage the microcontroller clock setting is already configured, + this is done through SystemInit() function which is called from startup + file (startup_stm32f10x_xx.s) before to branch to application main. + To reconfigure the default setting of SystemInit() function, refer to + system_stm32f10x.c file + */ + + /* System Clocks Configuration */ + RCC_Configuration(); + + /* FSMC for SRAM and SRAM pins configuration */ + SRAM_Init(); + + /* Write to FSMC -----------------------------------------------------------*/ + /* DMA2 channel5 configuration */ + DMA_DeInit(DMA2_Channel5); + DMA_InitStructure.DMA_PeripheralBaseAddr = (uint32_t)SRC_Const_Buffer; + DMA_InitStructure.DMA_MemoryBaseAddr = (uint32_t)Bank1_SRAM3_ADDR; + DMA_InitStructure.DMA_DIR = DMA_DIR_PeripheralSRC; + DMA_InitStructure.DMA_BufferSize = 32; + DMA_InitStructure.DMA_PeripheralInc = DMA_PeripheralInc_Enable; + DMA_InitStructure.DMA_MemoryInc = DMA_MemoryInc_Enable; + DMA_InitStructure.DMA_PeripheralDataSize = DMA_PeripheralDataSize_Word; + DMA_InitStructure.DMA_MemoryDataSize = DMA_MemoryDataSize_Word; + DMA_InitStructure.DMA_Mode = DMA_Mode_Normal; + DMA_InitStructure.DMA_Priority = DMA_Priority_High; + DMA_InitStructure.DMA_M2M = DMA_M2M_Enable; + DMA_Init(DMA2_Channel5, &DMA_InitStructure); + + /* Enable DMA2 channel5 */ + DMA_Cmd(DMA2_Channel5, ENABLE); + + /* Check if DMA2 channel5 transfer is finished */ + while(!DMA_GetFlagStatus(DMA2_FLAG_TC5)); + + /* Clear DMA2 channel5 transfer complete flag bit */ + DMA_ClearFlag(DMA2_FLAG_TC5); + + /* Read from FSMC ----------------------------------------------------------*/ + /* Destination buffer initialization */ + for(Idx=0; Idx<128; Idx++) DST_Buffer[Idx]=0; + + /* DMA1 channel3 configuration */ + DMA_DeInit(DMA1_Channel3); + DMA_InitStructure.DMA_PeripheralBaseAddr = (uint32_t)Bank1_SRAM3_ADDR; + DMA_InitStructure.DMA_MemoryBaseAddr = (uint32_t)DST_Buffer; + DMA_InitStructure.DMA_DIR = DMA_DIR_PeripheralSRC; + DMA_InitStructure.DMA_BufferSize = 128; + DMA_InitStructure.DMA_PeripheralInc = DMA_PeripheralInc_Enable; + DMA_InitStructure.DMA_MemoryInc = DMA_MemoryInc_Enable; + DMA_InitStructure.DMA_PeripheralDataSize = DMA_PeripheralDataSize_Byte; + DMA_InitStructure.DMA_MemoryDataSize = DMA_MemoryDataSize_Byte; + DMA_InitStructure.DMA_Mode = DMA_Mode_Normal; + DMA_InitStructure.DMA_Priority = DMA_Priority_High; + DMA_InitStructure.DMA_M2M = DMA_M2M_Enable; + DMA_Init(DMA1_Channel3, &DMA_InitStructure); + + /* Enable DMA1 channel3 */ + DMA_Cmd(DMA1_Channel3, ENABLE); + + /* Check if DMA1 channel3 transfer is finished */ + while(!DMA_GetFlagStatus(DMA1_FLAG_TC3)); + + /* Clear DMA1 channel3 transfer complete flag bit */ + DMA_ClearFlag(DMA1_FLAG_TC3); + + /* Check if the transmitted and received data are equal */ + TransferStatus = Buffercmp(SRC_Const_Buffer, (uint32_t*)DST_Buffer, BufferSize); + /* TransferStatus = PASSED, if the transmitted and received data + are the same */ + /* TransferStatus = FAILED, if the transmitted and received data + are different */ + + while (1) + { + } +} + +/** + * @brief Configures the different system clocks. + * @param None + * @retval None + */ +void RCC_Configuration(void) +{ + /* Enable peripheral clocks ------------------------------------------------*/ + /* DMA1 and DMA2 clock enable */ + RCC_AHBPeriphClockCmd(RCC_AHBPeriph_DMA1 | RCC_AHBPeriph_DMA2, ENABLE); + /* FSMC clock enable */ + RCC_AHBPeriphClockCmd(RCC_AHBPeriph_FSMC, ENABLE); +} + +/** + * @brief Compares two buffers. + * @param pBuffer, pBuffer1: buffers to be compared. + * @param BufferLength: buffer's length + * @retval PASSED: pBuffer identical to pBuffer1 + * FAILED: pBuffer differs from pBuffer1 + */ +TestStatus Buffercmp(const uint32_t* pBuffer, uint32_t* pBuffer1, uint16_t BufferLength) +{ + while(BufferLength--) + { + if(*pBuffer != *pBuffer1) + { + return FAILED; + } + + pBuffer++; + pBuffer1++; + } + + return PASSED; +} + +#ifdef USE_FULL_ASSERT + +/** + * @brief Reports the name of the source file and the source line number + * where the assert_param error has occurred. + * @param file: pointer to the source file name + * @param line: assert_param error line source number + * @retval None + */ +void assert_failed(uint8_t* file, uint32_t line) +{ + /* User can add his own implementation to report the file name and line number, + ex: printf("Wrong parameters value: file %s on line %d\r\n", file, line) */ + + /* Infinite loop */ + while (1) + { + } +} + +#endif + +/** + * @} + */ + +/** + * @} + */ + +/******************* (C) COPYRIGHT 2011 STMicroelectronics *****END OF FILE****/ diff --git a/tmp/STM32F10x_StdPeriph_Lib_V3.5.0/Project/STM32F10x_StdPeriph_Examples/DMA/FSMC/readme.txt b/tmp/STM32F10x_StdPeriph_Lib_V3.5.0/Project/STM32F10x_StdPeriph_Examples/DMA/FSMC/readme.txt new file mode 100644 index 0000000..d53bfe6 --- /dev/null +++ b/tmp/STM32F10x_StdPeriph_Lib_V3.5.0/Project/STM32F10x_StdPeriph_Examples/DMA/FSMC/readme.txt @@ -0,0 +1,92 @@ +/** + @page DMA_FSMC DMA FSMC example + + @verbatim + ******************** (C) COPYRIGHT 2011 STMicroelectronics ******************* + * @file DMA/FSMC/readme.txt + * @author MCD Application Team + * @version V3.5.0 + * @date 08-April-2011 + * @brief Description of the DMA FSMC example. + ****************************************************************************** + * THE PRESENT FIRMWARE WHICH IS FOR GUIDANCE ONLY AIMS AT PROVIDING CUSTOMERS + * WITH CODING INFORMATION REGARDING THEIR PRODUCTS IN ORDER FOR THEM TO SAVE + * TIME. AS A RESULT, STMICROELECTRONICS SHALL NOT BE HELD LIABLE FOR ANY + * DIRECT, INDIRECT OR CONSEQUENTIAL DAMAGES WITH RESPECT TO ANY CLAIMS ARISING + * FROM THE CONTENT OF SUCH FIRMWARE AND/OR THE USE MADE BY CUSTOMERS OF THE + * CODING INFORMATION CONTAINED HEREIN IN CONNECTION WITH THEIR PRODUCTS. + ****************************************************************************** + @endverbatim + +@par Example Description + +This example provides a description of how to use two DMA channels to transfer +a word data buffer from Flash memory to external SRAM memory and to recuperate +the written data from external SRAM to be stored in internal SRAM. + +DMA2 Channel5 is configured to transfer, word by word, the contents of a 32-word data +buffer stored in Flash memory to the external SRAM memory interfaced by FSMC. +The start of transfer is triggered by software. DMA2 Channel5 memory-to-memory +transfer is enabled. +Source and destination address incrementing is also enabled. The transfer is started +by setting the Channel enable bit for DMA2 Channel5. A polling on the Transfer Complete +flag is done to check the end of transfer. The DMA2 Channel5 Transfer complete flag +is then cleared. + +DMA1 Channel3 is configured to transfer, byte by byte, the contents of the first +128Bytes of external SRAM to the internal SRAM memory. The start of transfer is +triggered by software. DMA1 Channel3 memory-to-memory transfer is enabled. +Source and destination address incrementing is also enabled. The transfer is started +by setting the Channel enable bit for DMA1 Channel3. A polling on the Transfer Complete +flag is done to check the end of transfer. + +A comparison between the source and destination buffers is done to check that all data +have been correctly transferred. + + +@par Directory contents + + - DMA/FSMC/stm32f10x_conf.h Library Configuration file + - DMA/FSMC/stm32f10x_it.c Interrupt handlers + - DMA/FSMC/stm32f10x_it.h Interrupt handlers header file + - DMA/FSMC/main.c Main program + - DMA/FSMC/system_stm32f10x.c STM32F10x system source file + +@par Hardware and Software environment + + - This example runs only on STM32F10x High-Density, High-Density Value line + and XL-Density Devices. + + - This example has been tested with STMicroelectronics STM32100E-EVAL (High-Density + Value line) and STM3210E-EVAL (High-Density and XL-Density) evaluation boards + and can be easily tailored to any other supported device and development board. + + +@par How to use it ? + +In order to make the program work, you must do the following : + - Copy all source files from this example folder to the template folder under + Project\STM32F10x_StdPeriph_Template + - Open your preferred toolchain + - Rebuild all files and load your image into target memory + - Run the example + +@note + - Low-density Value line devices are STM32F100xx microcontrollers where the + Flash memory density ranges between 16 and 32 Kbytes. + - Low-density devices are STM32F101xx, STM32F102xx and STM32F103xx + microcontrollers where the Flash memory density ranges between 16 and 32 Kbytes. + - Medium-density Value line devices are STM32F100xx microcontrollers where + the Flash memory density ranges between 64 and 128 Kbytes. + - Medium-density devices are STM32F101xx, STM32F102xx and STM32F103xx + microcontrollers where the Flash memory density ranges between 64 and 128 Kbytes. + - High-density devices are STM32F101xx and STM32F103xx microcontrollers where + the Flash memory density ranges between 256 and 512 Kbytes. + - High-density Value line devices are STM32F100xx microcontrollers where + the Flash memory density ranges between 256 and 512 Kbytes. + - XL-density devices are STM32F101xx and STM32F103xx microcontrollers where + the Flash memory density ranges between 512 and 1024 Kbytes. + - Connectivity line devices are STM32F105xx and STM32F107xx microcontrollers. + + *

© COPYRIGHT 2011 STMicroelectronics

+ */ diff --git a/tmp/STM32F10x_StdPeriph_Lib_V3.5.0/Project/STM32F10x_StdPeriph_Examples/DMA/FSMC/stm32f10x_conf.h b/tmp/STM32F10x_StdPeriph_Lib_V3.5.0/Project/STM32F10x_StdPeriph_Examples/DMA/FSMC/stm32f10x_conf.h new file mode 100644 index 0000000..119260e --- /dev/null +++ b/tmp/STM32F10x_StdPeriph_Lib_V3.5.0/Project/STM32F10x_StdPeriph_Examples/DMA/FSMC/stm32f10x_conf.h @@ -0,0 +1,77 @@ +/** + ****************************************************************************** + * @file DMA/FSMC/stm32f10x_conf.h + * @author MCD Application Team + * @version V3.5.0 + * @date 08-April-2011 + * @brief Library configuration file. + ****************************************************************************** + * @attention + * + * THE PRESENT FIRMWARE WHICH IS FOR GUIDANCE ONLY AIMS AT PROVIDING CUSTOMERS + * WITH CODING INFORMATION REGARDING THEIR PRODUCTS IN ORDER FOR THEM TO SAVE + * TIME. AS A RESULT, STMICROELECTRONICS SHALL NOT BE HELD LIABLE FOR ANY + * DIRECT, INDIRECT OR CONSEQUENTIAL DAMAGES WITH RESPECT TO ANY CLAIMS ARISING + * FROM THE CONTENT OF SUCH FIRMWARE AND/OR THE USE MADE BY CUSTOMERS OF THE + * CODING INFORMATION CONTAINED HEREIN IN CONNECTION WITH THEIR PRODUCTS. + * + *

© COPYRIGHT 2011 STMicroelectronics

+ ****************************************************************************** + */ + +/* Define to prevent recursive inclusion -------------------------------------*/ +#ifndef __STM32F10x_CONF_H +#define __STM32F10x_CONF_H + +/* Includes ------------------------------------------------------------------*/ +/* Uncomment/Comment the line below to enable/disable peripheral header file inclusion */ +#include "stm32f10x_adc.h" +#include "stm32f10x_bkp.h" +#include "stm32f10x_can.h" +#include "stm32f10x_cec.h" +#include "stm32f10x_crc.h" +#include "stm32f10x_dac.h" +#include "stm32f10x_dbgmcu.h" +#include "stm32f10x_dma.h" +#include "stm32f10x_exti.h" +#include "stm32f10x_flash.h" +#include "stm32f10x_fsmc.h" +#include "stm32f10x_gpio.h" +#include "stm32f10x_i2c.h" +#include "stm32f10x_iwdg.h" +#include "stm32f10x_pwr.h" +#include "stm32f10x_rcc.h" +#include "stm32f10x_rtc.h" +#include "stm32f10x_sdio.h" +#include "stm32f10x_spi.h" +#include "stm32f10x_tim.h" +#include "stm32f10x_usart.h" +#include "stm32f10x_wwdg.h" +#include "misc.h" /* High level functions for NVIC and SysTick (add-on to CMSIS functions) */ + +/* Exported types ------------------------------------------------------------*/ +/* Exported constants --------------------------------------------------------*/ +/* Uncomment the line below to expanse the "assert_param" macro in the + Standard Peripheral Library drivers code */ +/* #define USE_FULL_ASSERT 1 */ + +/* Exported macro ------------------------------------------------------------*/ +#ifdef USE_FULL_ASSERT + +/** + * @brief The assert_param macro is used for function's parameters check. + * @param expr: If expr is false, it calls assert_failed function which reports + * the name of the source file and the source line number of the call + * that failed. If expr is true, it returns no value. + * @retval None + */ + #define assert_param(expr) ((expr) ? (void)0 : assert_failed((uint8_t *)__FILE__, __LINE__)) +/* Exported functions ------------------------------------------------------- */ + void assert_failed(uint8_t* file, uint32_t line); +#else + #define assert_param(expr) ((void)0) +#endif /* USE_FULL_ASSERT */ + +#endif /* __STM32F10x_CONF_H */ + +/******************* (C) COPYRIGHT 2011 STMicroelectronics *****END OF FILE****/ diff --git a/tmp/STM32F10x_StdPeriph_Lib_V3.5.0/Project/STM32F10x_StdPeriph_Examples/DMA/FSMC/stm32f10x_it.c b/tmp/STM32F10x_StdPeriph_Lib_V3.5.0/Project/STM32F10x_StdPeriph_Examples/DMA/FSMC/stm32f10x_it.c new file mode 100644 index 0000000..b5ab495 --- /dev/null +++ b/tmp/STM32F10x_StdPeriph_Lib_V3.5.0/Project/STM32F10x_StdPeriph_Examples/DMA/FSMC/stm32f10x_it.c @@ -0,0 +1,167 @@ +/** + ****************************************************************************** + * @file DMA/FSMC/stm32f10x_it.c + * @author MCD Application Team + * @version V3.5.0 + * @date 08-April-2011 + * @brief Main Interrupt Service Routines. + * This file provides template for all exceptions handler and peripherals + * interrupt service routine. + ****************************************************************************** + * @attention + * + * THE PRESENT FIRMWARE WHICH IS FOR GUIDANCE ONLY AIMS AT PROVIDING CUSTOMERS + * WITH CODING INFORMATION REGARDING THEIR PRODUCTS IN ORDER FOR THEM TO SAVE + * TIME. AS A RESULT, STMICROELECTRONICS SHALL NOT BE HELD LIABLE FOR ANY + * DIRECT, INDIRECT OR CONSEQUENTIAL DAMAGES WITH RESPECT TO ANY CLAIMS ARISING + * FROM THE CONTENT OF SUCH FIRMWARE AND/OR THE USE MADE BY CUSTOMERS OF THE + * CODING INFORMATION CONTAINED HEREIN IN CONNECTION WITH THEIR PRODUCTS. + * + *

© COPYRIGHT 2011 STMicroelectronics

+ ****************************************************************************** + */ + +/* Includes ------------------------------------------------------------------*/ +#include "stm32f10x_it.h" + +/** @addtogroup STM32F10x_StdPeriph_Examples + * @{ + */ + +/** @addtogroup DMA_FSMC + * @{ + */ + +/* Private typedef -----------------------------------------------------------*/ +/* Private define ------------------------------------------------------------*/ +/* Private macro -------------------------------------------------------------*/ +/* Private variables ---------------------------------------------------------*/ +/* Private function prototypes -----------------------------------------------*/ +/* Private functions ---------------------------------------------------------*/ + +/******************************************************************************/ +/* Cortex-M3 Processor Exceptions Handlers */ +/******************************************************************************/ + +/** + * @brief This function handles NMI exception. + * @param None + * @retval None + */ +void NMI_Handler(void) +{ +} + +/** + * @brief This function handles Hard Fault exception. + * @param None + * @retval None + */ +void HardFault_Handler(void) +{ + /* Go to infinite loop when Hard Fault exception occurs */ + while (1) + { + } +} + +/** + * @brief This function handles Memory Manage exception. + * @param None + * @retval None + */ +void MemManage_Handler(void) +{ + /* Go to infinite loop when Memory Manage exception occurs */ + while (1) + { + } +} + +/** + * @brief This function handles Bus Fault exception. + * @param None + * @retval None + */ +void BusFault_Handler(void) +{ + /* Go to infinite loop when Bus Fault exception occurs */ + while (1) + { + } +} + +/** + * @brief This function handles Usage Fault exception. + * @param None + * @retval None + */ +void UsageFault_Handler(void) +{ + /* Go to infinite loop when Usage Fault exception occurs */ + while (1) + { + } +} + +/** + * @brief This function handles SVCall exception. + * @param None + * @retval None + */ +void SVC_Handler(void) +{ +} + +/** + * @brief This function handles Debug Monitor exception. + * @param None + * @retval None + */ +void DebugMon_Handler(void) +{ +} + +/** + * @brief This function handles PendSV_Handler exception. + * @param None + * @retval None + */ +void PendSV_Handler(void) +{ +} + +/** + * @brief This function handles SysTick Handler. + * @param None + * @retval None + */ +void SysTick_Handler(void) +{ +} + +/******************************************************************************/ +/* STM32F10x Peripherals Interrupt Handlers */ +/* Add here the Interrupt Handler for the used peripheral(s) (PPP), for the */ +/* available peripheral interrupt handler's name please refer to the startup */ +/* file (startup_stm32f10x_xx.s). */ +/******************************************************************************/ + +/** + * @brief This function handles PPP interrupt request. + * @param None + * @retval None + */ +/*void PPP_IRQHandler(void) +{ +}*/ + +/** + * @} + */ + +/** + * @} + */ + +/******************* (C) COPYRIGHT 2011 STMicroelectronics *****END OF FILE****/ diff --git a/tmp/STM32F10x_StdPeriph_Lib_V3.5.0/Project/STM32F10x_StdPeriph_Examples/DMA/FSMC/stm32f10x_it.h b/tmp/STM32F10x_StdPeriph_Lib_V3.5.0/Project/STM32F10x_StdPeriph_Examples/DMA/FSMC/stm32f10x_it.h new file mode 100644 index 0000000..7de2e62 --- /dev/null +++ b/tmp/STM32F10x_StdPeriph_Lib_V3.5.0/Project/STM32F10x_StdPeriph_Examples/DMA/FSMC/stm32f10x_it.h @@ -0,0 +1,46 @@ +/** + ****************************************************************************** + * @file DMA/FSMC/stm32f10x_it.h + * @author MCD Application Team + * @version V3.5.0 + * @date 08-April-2011 + * @brief This file contains the headers of the interrupt handlers. + ****************************************************************************** + * @attention + * + * THE PRESENT FIRMWARE WHICH IS FOR GUIDANCE ONLY AIMS AT PROVIDING CUSTOMERS + * WITH CODING INFORMATION REGARDING THEIR PRODUCTS IN ORDER FOR THEM TO SAVE + * TIME. AS A RESULT, STMICROELECTRONICS SHALL NOT BE HELD LIABLE FOR ANY + * DIRECT, INDIRECT OR CONSEQUENTIAL DAMAGES WITH RESPECT TO ANY CLAIMS ARISING + * FROM THE CONTENT OF SUCH FIRMWARE AND/OR THE USE MADE BY CUSTOMERS OF THE + * CODING INFORMATION CONTAINED HEREIN IN CONNECTION WITH THEIR PRODUCTS. + * + *

© COPYRIGHT 2011 STMicroelectronics

+ ****************************************************************************** + */ + +/* Define to prevent recursive inclusion -------------------------------------*/ +#ifndef __STM32F10x_IT_H +#define __STM32F10x_IT_H + +/* Includes ------------------------------------------------------------------*/ +#include "stm32f10x.h" + +/* Exported types ------------------------------------------------------------*/ +/* Exported constants --------------------------------------------------------*/ +/* Exported macro ------------------------------------------------------------*/ +/* Exported functions ------------------------------------------------------- */ + +void NMI_Handler(void); +void HardFault_Handler(void); +void MemManage_Handler(void); +void BusFault_Handler(void); +void UsageFault_Handler(void); +void SVC_Handler(void); +void DebugMon_Handler(void); +void PendSV_Handler(void); +void SysTick_Handler(void); + +#endif /* __STM32F10x_IT_H */ + +/******************* (C) COPYRIGHT 2011 STMicroelectronics *****END OF FILE****/ diff --git a/tmp/STM32F10x_StdPeriph_Lib_V3.5.0/Project/STM32F10x_StdPeriph_Examples/DMA/FSMC/system_stm32f10x.c b/tmp/STM32F10x_StdPeriph_Lib_V3.5.0/Project/STM32F10x_StdPeriph_Examples/DMA/FSMC/system_stm32f10x.c new file mode 100644 index 0000000..2ac6698 --- /dev/null +++ b/tmp/STM32F10x_StdPeriph_Lib_V3.5.0/Project/STM32F10x_StdPeriph_Examples/DMA/FSMC/system_stm32f10x.c @@ -0,0 +1,1094 @@ +/** + ****************************************************************************** + * @file DMA/FSMC/system_stm32f10x.c + * @author MCD Application Team + * @version V3.5.0 + * @date 08-April-2011 + * @brief CMSIS Cortex-M3 Device Peripheral Access Layer System Source File. + * + * 1. This file provides two functions and one global variable to be called from + * user application: + * - SystemInit(): Setups the system clock (System clock source, PLL Multiplier + * factors, AHB/APBx prescalers and Flash settings). + * This function is called at startup just after reset and + * before branch to main program. This call is made inside + * the "startup_stm32f10x_xx.s" file. + * + * - SystemCoreClock variable: Contains the core clock (HCLK), it can be used + * by the user application to setup the SysTick + * timer or configure other parameters. + * + * - SystemCoreClockUpdate(): Updates the variable SystemCoreClock and must + * be called whenever the core clock is changed + * during program execution. + * + * 2. After each device reset the HSI (8 MHz) is used as system clock source. + * Then SystemInit() function is called, in "startup_stm32f10x_xx.s" file, to + * configure the system clock before to branch to main program. + * + * 3. If the system clock source selected by user fails to startup, the SystemInit() + * function will do nothing and HSI still used as system clock source. User can + * add some code to deal with this issue inside the SetSysClock() function. + * + * 4. The default value of HSE crystal is set to 8 MHz (or 25 MHz, depedning on + * the product used), refer to "HSE_VALUE" define in "stm32f10x.h" file. + * When HSE is used as system clock source, directly or through PLL, and you + * are using different crystal you have to adapt the HSE value to your own + * configuration. + * + ****************************************************************************** + * @attention + * + * THE PRESENT FIRMWARE WHICH IS FOR GUIDANCE ONLY AIMS AT PROVIDING CUSTOMERS + * WITH CODING INFORMATION REGARDING THEIR PRODUCTS IN ORDER FOR THEM TO SAVE + * TIME. AS A RESULT, STMICROELECTRONICS SHALL NOT BE HELD LIABLE FOR ANY + * DIRECT, INDIRECT OR CONSEQUENTIAL DAMAGES WITH RESPECT TO ANY CLAIMS ARISING + * FROM THE CONTENT OF SUCH FIRMWARE AND/OR THE USE MADE BY CUSTOMERS OF THE + * CODING INFORMATION CONTAINED HEREIN IN CONNECTION WITH THEIR PRODUCTS. + * + *

© COPYRIGHT 2011 STMicroelectronics

+ ****************************************************************************** + */ + +/** @addtogroup CMSIS + * @{ + */ + +/** @addtogroup stm32f10x_system + * @{ + */ + +/** @addtogroup STM32F10x_System_Private_Includes + * @{ + */ + +#include "stm32f10x.h" + +/** + * @} + */ + +/** @addtogroup STM32F10x_System_Private_TypesDefinitions + * @{ + */ + +/** + * @} + */ + +/** @addtogroup STM32F10x_System_Private_Defines + * @{ + */ + +/*!< Uncomment the line corresponding to the desired System clock (SYSCLK) + frequency (after reset the HSI is used as SYSCLK source) + + IMPORTANT NOTE: + ============== + 1. After each device reset the HSI is used as System clock source. + + 2. Please make sure that the selected System clock doesn't exceed your device's + maximum frequency. + + 3. If none of the define below is enabled, the HSI is used as System clock + source. + + 4. The System clock configuration functions provided within this file assume that: + - For Low, Medium and High density Value line devices an external 8MHz + crystal is used to drive the System clock. + - For Low, Medium and High density devices an external 8MHz crystal is + used to drive the System clock. + - For Connectivity line devices an external 25MHz crystal is used to drive + the System clock. + If you are using different crystal you have to adapt those functions accordingly. + */ + +#if defined (STM32F10X_LD_VL) || (defined STM32F10X_MD_VL) || (defined STM32F10X_HD_VL) +/* #define SYSCLK_FREQ_HSE HSE_VALUE */ + #define SYSCLK_FREQ_24MHz 24000000 +#else +/* #define SYSCLK_FREQ_HSE HSE_VALUE */ +/* #define SYSCLK_FREQ_24MHz 24000000 */ +/* #define SYSCLK_FREQ_36MHz 36000000 */ +/* #define SYSCLK_FREQ_48MHz 48000000 */ +/* #define SYSCLK_FREQ_56MHz 56000000 */ +#define SYSCLK_FREQ_72MHz 72000000 +#endif + +/*!< Uncomment the following line if you need to use external SRAM mounted + on STM3210E-EVAL board (STM32 High density and XL-density devices) or on + STM32100E-EVAL board (STM32 High-density value line devices) as data memory */ +#if defined (STM32F10X_HD) || (defined STM32F10X_XL) || (defined STM32F10X_HD_VL) +/* #define DATA_IN_ExtSRAM */ +#endif + +/*!< Uncomment the following line if you need to relocate your vector Table in + Internal SRAM. */ +/* #define VECT_TAB_SRAM */ +#define VECT_TAB_OFFSET 0x0 /*!< Vector Table base offset field. + This value must be a multiple of 0x200. */ + + +/** + * @} + */ + +/** @addtogroup STM32F10x_System_Private_Macros + * @{ + */ + +/** + * @} + */ + +/** @addtogroup STM32F10x_System_Private_Variables + * @{ + */ + +/******************************************************************************* +* Clock Definitions +*******************************************************************************/ +#ifdef SYSCLK_FREQ_HSE + uint32_t SystemCoreClock = SYSCLK_FREQ_HSE; /*!< System Clock Frequency (Core Clock) */ +#elif defined SYSCLK_FREQ_24MHz + uint32_t SystemCoreClock = SYSCLK_FREQ_24MHz; /*!< System Clock Frequency (Core Clock) */ +#elif defined SYSCLK_FREQ_36MHz + uint32_t SystemCoreClock = SYSCLK_FREQ_36MHz; /*!< System Clock Frequency (Core Clock) */ +#elif defined SYSCLK_FREQ_48MHz + uint32_t SystemCoreClock = SYSCLK_FREQ_48MHz; /*!< System Clock Frequency (Core Clock) */ +#elif defined SYSCLK_FREQ_56MHz + uint32_t SystemCoreClock = SYSCLK_FREQ_56MHz; /*!< System Clock Frequency (Core Clock) */ +#elif defined SYSCLK_FREQ_72MHz + uint32_t SystemCoreClock = SYSCLK_FREQ_72MHz; /*!< System Clock Frequency (Core Clock) */ +#else /*!< HSI Selected as System Clock source */ + uint32_t SystemCoreClock = HSI_VALUE; /*!< System Clock Frequency (Core Clock) */ +#endif + +__I uint8_t AHBPrescTable[16] = {0, 0, 0, 0, 0, 0, 0, 0, 1, 2, 3, 4, 6, 7, 8, 9}; +/** + * @} + */ + +/** @addtogroup STM32F10x_System_Private_FunctionPrototypes + * @{ + */ + +static void SetSysClock(void); + +#ifdef SYSCLK_FREQ_HSE + static void SetSysClockToHSE(void); +#elif defined SYSCLK_FREQ_24MHz + static void SetSysClockTo24(void); +#elif defined SYSCLK_FREQ_36MHz + static void SetSysClockTo36(void); +#elif defined SYSCLK_FREQ_48MHz + static void SetSysClockTo48(void); +#elif defined SYSCLK_FREQ_56MHz + static void SetSysClockTo56(void); +#elif defined SYSCLK_FREQ_72MHz + static void SetSysClockTo72(void); +#endif + +#ifdef DATA_IN_ExtSRAM + static void SystemInit_ExtMemCtl(void); +#endif /* DATA_IN_ExtSRAM */ + +/** + * @} + */ + +/** @addtogroup STM32F10x_System_Private_Functions + * @{ + */ + +/** + * @brief Setup the microcontroller system + * Initialize the Embedded Flash Interface, the PLL and update the + * SystemCoreClock variable. + * @note This function should be used only after reset. + * @param None + * @retval None + */ +void SystemInit (void) +{ + /* Reset the RCC clock configuration to the default reset state(for debug purpose) */ + /* Set HSION bit */ + RCC->CR |= (uint32_t)0x00000001; + + /* Reset SW, HPRE, PPRE1, PPRE2, ADCPRE and MCO bits */ +#ifndef STM32F10X_CL + RCC->CFGR &= (uint32_t)0xF8FF0000; +#else + RCC->CFGR &= (uint32_t)0xF0FF0000; +#endif /* STM32F10X_CL */ + + /* Reset HSEON, CSSON and PLLON bits */ + RCC->CR &= (uint32_t)0xFEF6FFFF; + + /* Reset HSEBYP bit */ + RCC->CR &= (uint32_t)0xFFFBFFFF; + + /* Reset PLLSRC, PLLXTPRE, PLLMUL and USBPRE/OTGFSPRE bits */ + RCC->CFGR &= (uint32_t)0xFF80FFFF; + +#ifdef STM32F10X_CL + /* Reset PLL2ON and PLL3ON bits */ + RCC->CR &= (uint32_t)0xEBFFFFFF; + + /* Disable all interrupts and clear pending bits */ + RCC->CIR = 0x00FF0000; + + /* Reset CFGR2 register */ + RCC->CFGR2 = 0x00000000; +#elif defined (STM32F10X_LD_VL) || defined (STM32F10X_MD_VL) || (defined STM32F10X_HD_VL) + /* Disable all interrupts and clear pending bits */ + RCC->CIR = 0x009F0000; + + /* Reset CFGR2 register */ + RCC->CFGR2 = 0x00000000; +#else + /* Disable all interrupts and clear pending bits */ + RCC->CIR = 0x009F0000; +#endif /* STM32F10X_CL */ + +#if defined (STM32F10X_HD) || (defined STM32F10X_XL) || (defined STM32F10X_HD_VL) + #ifdef DATA_IN_ExtSRAM + SystemInit_ExtMemCtl(); + #endif /* DATA_IN_ExtSRAM */ +#endif + + /* Configure the System clock frequency, HCLK, PCLK2 and PCLK1 prescalers */ + /* Configure the Flash Latency cycles and enable prefetch buffer */ + SetSysClock(); + +#ifdef VECT_TAB_SRAM + SCB->VTOR = SRAM_BASE | VECT_TAB_OFFSET; /* Vector Table Relocation in Internal SRAM. */ +#else + SCB->VTOR = FLASH_BASE | VECT_TAB_OFFSET; /* Vector Table Relocation in Internal FLASH. */ +#endif +} + +/** + * @brief Update SystemCoreClock variable according to Clock Register Values. + * The SystemCoreClock variable contains the core clock (HCLK), it can + * be used by the user application to setup the SysTick timer or configure + * other parameters. + * + * @note Each time the core clock (HCLK) changes, this function must be called + * to update SystemCoreClock variable value. Otherwise, any configuration + * based on this variable will be incorrect. + * + * @note - The system frequency computed by this function is not the real + * frequency in the chip. It is calculated based on the predefined + * constant and the selected clock source: + * + * - If SYSCLK source is HSI, SystemCoreClock will contain the HSI_VALUE(*) + * + * - If SYSCLK source is HSE, SystemCoreClock will contain the HSE_VALUE(**) + * + * - If SYSCLK source is PLL, SystemCoreClock will contain the HSE_VALUE(**) + * or HSI_VALUE(*) multiplied by the PLL factors. + * + * (*) HSI_VALUE is a constant defined in stm32f1xx.h file (default value + * 8 MHz) but the real value may vary depending on the variations + * in voltage and temperature. + * + * (**) HSE_VALUE is a constant defined in stm32f1xx.h file (default value + * 8 MHz or 25 MHz, depedning on the product used), user has to ensure + * that HSE_VALUE is same as the real frequency of the crystal used. + * Otherwise, this function may have wrong result. + * + * - The result of this function could be not correct when using fractional + * value for HSE crystal. + * @param None + * @retval None + */ +void SystemCoreClockUpdate (void) +{ + uint32_t tmp = 0, pllmull = 0, pllsource = 0; + +#ifdef STM32F10X_CL + uint32_t prediv1source = 0, prediv1factor = 0, prediv2factor = 0, pll2mull = 0; +#endif /* STM32F10X_CL */ + +#if defined (STM32F10X_LD_VL) || defined (STM32F10X_MD_VL) || (defined STM32F10X_HD_VL) + uint32_t prediv1factor = 0; +#endif /* STM32F10X_LD_VL or STM32F10X_MD_VL or STM32F10X_HD_VL */ + + /* Get SYSCLK source -------------------------------------------------------*/ + tmp = RCC->CFGR & RCC_CFGR_SWS; + + switch (tmp) + { + case 0x00: /* HSI used as system clock */ + SystemCoreClock = HSI_VALUE; + break; + case 0x04: /* HSE used as system clock */ + SystemCoreClock = HSE_VALUE; + break; + case 0x08: /* PLL used as system clock */ + + /* Get PLL clock source and multiplication factor ----------------------*/ + pllmull = RCC->CFGR & RCC_CFGR_PLLMULL; + pllsource = RCC->CFGR & RCC_CFGR_PLLSRC; + +#ifndef STM32F10X_CL + pllmull = ( pllmull >> 18) + 2; + + if (pllsource == 0x00) + { + /* HSI oscillator clock divided by 2 selected as PLL clock entry */ + SystemCoreClock = (HSI_VALUE >> 1) * pllmull; + } + else + { + #if defined (STM32F10X_LD_VL) || defined (STM32F10X_MD_VL) || (defined STM32F10X_HD_VL) + prediv1factor = (RCC->CFGR2 & RCC_CFGR2_PREDIV1) + 1; + /* HSE oscillator clock selected as PREDIV1 clock entry */ + SystemCoreClock = (HSE_VALUE / prediv1factor) * pllmull; + #else + /* HSE selected as PLL clock entry */ + if ((RCC->CFGR & RCC_CFGR_PLLXTPRE) != (uint32_t)RESET) + {/* HSE oscillator clock divided by 2 */ + SystemCoreClock = (HSE_VALUE >> 1) * pllmull; + } + else + { + SystemCoreClock = HSE_VALUE * pllmull; + } + #endif + } +#else + pllmull = pllmull >> 18; + + if (pllmull != 0x0D) + { + pllmull += 2; + } + else + { /* PLL multiplication factor = PLL input clock * 6.5 */ + pllmull = 13 / 2; + } + + if (pllsource == 0x00) + { + /* HSI oscillator clock divided by 2 selected as PLL clock entry */ + SystemCoreClock = (HSI_VALUE >> 1) * pllmull; + } + else + {/* PREDIV1 selected as PLL clock entry */ + + /* Get PREDIV1 clock source and division factor */ + prediv1source = RCC->CFGR2 & RCC_CFGR2_PREDIV1SRC; + prediv1factor = (RCC->CFGR2 & RCC_CFGR2_PREDIV1) + 1; + + if (prediv1source == 0) + { + /* HSE oscillator clock selected as PREDIV1 clock entry */ + SystemCoreClock = (HSE_VALUE / prediv1factor) * pllmull; + } + else + {/* PLL2 clock selected as PREDIV1 clock entry */ + + /* Get PREDIV2 division factor and PLL2 multiplication factor */ + prediv2factor = ((RCC->CFGR2 & RCC_CFGR2_PREDIV2) >> 4) + 1; + pll2mull = ((RCC->CFGR2 & RCC_CFGR2_PLL2MUL) >> 8 ) + 2; + SystemCoreClock = (((HSE_VALUE / prediv2factor) * pll2mull) / prediv1factor) * pllmull; + } + } +#endif /* STM32F10X_CL */ + break; + + default: + SystemCoreClock = HSI_VALUE; + break; + } + + /* Compute HCLK clock frequency ----------------*/ + /* Get HCLK prescaler */ + tmp = AHBPrescTable[((RCC->CFGR & RCC_CFGR_HPRE) >> 4)]; + /* HCLK clock frequency */ + SystemCoreClock >>= tmp; +} + +/** + * @brief Configures the System clock frequency, HCLK, PCLK2 and PCLK1 prescalers. + * @param None + * @retval None + */ +static void SetSysClock(void) +{ +#ifdef SYSCLK_FREQ_HSE + SetSysClockToHSE(); +#elif defined SYSCLK_FREQ_24MHz + SetSysClockTo24(); +#elif defined SYSCLK_FREQ_36MHz + SetSysClockTo36(); +#elif defined SYSCLK_FREQ_48MHz + SetSysClockTo48(); +#elif defined SYSCLK_FREQ_56MHz + SetSysClockTo56(); +#elif defined SYSCLK_FREQ_72MHz + SetSysClockTo72(); +#endif + + /* If none of the define above is enabled, the HSI is used as System clock + source (default after reset) */ +} + +/** + * @brief Setup the external memory controller. Called in startup_stm32f10x.s + * before jump to __main + * @param None + * @retval None + */ +#ifdef DATA_IN_ExtSRAM +/** + * @brief Setup the external memory controller. + * Called in startup_stm32f10x_xx.s/.c before jump to main. + * This function configures the external SRAM mounted on STM3210E-EVAL + * board (STM32 High density devices). This SRAM will be used as program + * data memory (including heap and stack). + * @param None + * @retval None + */ +void SystemInit_ExtMemCtl(void) +{ +/*!< FSMC Bank1 NOR/SRAM3 is used for the STM3210E-EVAL, if another Bank is + required, then adjust the Register Addresses */ + + /* Enable FSMC clock */ + RCC->AHBENR = 0x00000114; + + /* Enable GPIOD, GPIOE, GPIOF and GPIOG clocks */ + RCC->APB2ENR = 0x000001E0; + +/* --------------- SRAM Data lines, NOE and NWE configuration ---------------*/ +/*---------------- SRAM Address lines configuration -------------------------*/ +/*---------------- NOE and NWE configuration --------------------------------*/ +/*---------------- NE3 configuration ----------------------------------------*/ +/*---------------- NBL0, NBL1 configuration ---------------------------------*/ + + GPIOD->CRL = 0x44BB44BB; + GPIOD->CRH = 0xBBBBBBBB; + + GPIOE->CRL = 0xB44444BB; + GPIOE->CRH = 0xBBBBBBBB; + + GPIOF->CRL = 0x44BBBBBB; + GPIOF->CRH = 0xBBBB4444; + + GPIOG->CRL = 0x44BBBBBB; + GPIOG->CRH = 0x44444B44; + +/*---------------- FSMC Configuration ---------------------------------------*/ +/*---------------- Enable FSMC Bank1_SRAM Bank ------------------------------*/ + + FSMC_Bank1->BTCR[4] = 0x00001011; + FSMC_Bank1->BTCR[5] = 0x00000200; +} +#endif /* DATA_IN_ExtSRAM */ + +#ifdef SYSCLK_FREQ_HSE +/** + * @brief Selects HSE as System clock source and configure HCLK, PCLK2 + * and PCLK1 prescalers. + * @note This function should be used only after reset. + * @param None + * @retval None + */ +static void SetSysClockToHSE(void) +{ + __IO uint32_t StartUpCounter = 0, HSEStatus = 0; + + /* SYSCLK, HCLK, PCLK2 and PCLK1 configuration ---------------------------*/ + /* Enable HSE */ + RCC->CR |= ((uint32_t)RCC_CR_HSEON); + + /* Wait till HSE is ready and if Time out is reached exit */ + do + { + HSEStatus = RCC->CR & RCC_CR_HSERDY; + StartUpCounter++; + } while((HSEStatus == 0) && (StartUpCounter != HSE_STARTUP_TIMEOUT)); + + if ((RCC->CR & RCC_CR_HSERDY) != RESET) + { + HSEStatus = (uint32_t)0x01; + } + else + { + HSEStatus = (uint32_t)0x00; + } + + if (HSEStatus == (uint32_t)0x01) + { + +#if !defined STM32F10X_LD_VL && !defined STM32F10X_MD_VL && !defined STM32F10X_HD_VL + /* Enable Prefetch Buffer */ + FLASH->ACR |= FLASH_ACR_PRFTBE; + + /* Flash 0 wait state */ + FLASH->ACR &= (uint32_t)((uint32_t)~FLASH_ACR_LATENCY); + +#ifndef STM32F10X_CL + FLASH->ACR |= (uint32_t)FLASH_ACR_LATENCY_0; +#else + if (HSE_VALUE <= 24000000) + { + FLASH->ACR |= (uint32_t)FLASH_ACR_LATENCY_0; + } + else + { + FLASH->ACR |= (uint32_t)FLASH_ACR_LATENCY_1; + } +#endif /* STM32F10X_CL */ +#endif + + /* HCLK = SYSCLK */ + RCC->CFGR |= (uint32_t)RCC_CFGR_HPRE_DIV1; + + /* PCLK2 = HCLK */ + RCC->CFGR |= (uint32_t)RCC_CFGR_PPRE2_DIV1; + + /* PCLK1 = HCLK */ + RCC->CFGR |= (uint32_t)RCC_CFGR_PPRE1_DIV1; + + /* Select HSE as system clock source */ + RCC->CFGR &= (uint32_t)((uint32_t)~(RCC_CFGR_SW)); + RCC->CFGR |= (uint32_t)RCC_CFGR_SW_HSE; + + /* Wait till HSE is used as system clock source */ + while ((RCC->CFGR & (uint32_t)RCC_CFGR_SWS) != (uint32_t)0x04) + { + } + } + else + { /* If HSE fails to start-up, the application will have wrong clock + configuration. User can add here some code to deal with this error */ + } +} +#elif defined SYSCLK_FREQ_24MHz +/** + * @brief Sets System clock frequency to 24MHz and configure HCLK, PCLK2 + * and PCLK1 prescalers. + * @note This function should be used only after reset. + * @param None + * @retval None + */ +static void SetSysClockTo24(void) +{ + __IO uint32_t StartUpCounter = 0, HSEStatus = 0; + + /* SYSCLK, HCLK, PCLK2 and PCLK1 configuration ---------------------------*/ + /* Enable HSE */ + RCC->CR |= ((uint32_t)RCC_CR_HSEON); + + /* Wait till HSE is ready and if Time out is reached exit */ + do + { + HSEStatus = RCC->CR & RCC_CR_HSERDY; + StartUpCounter++; + } while((HSEStatus == 0) && (StartUpCounter != HSE_STARTUP_TIMEOUT)); + + if ((RCC->CR & RCC_CR_HSERDY) != RESET) + { + HSEStatus = (uint32_t)0x01; + } + else + { + HSEStatus = (uint32_t)0x00; + } + + if (HSEStatus == (uint32_t)0x01) + { +#if !defined STM32F10X_LD_VL && !defined STM32F10X_MD_VL && !defined STM32F10X_HD_VL + /* Enable Prefetch Buffer */ + FLASH->ACR |= FLASH_ACR_PRFTBE; + + /* Flash 0 wait state */ + FLASH->ACR &= (uint32_t)((uint32_t)~FLASH_ACR_LATENCY); + FLASH->ACR |= (uint32_t)FLASH_ACR_LATENCY_0; +#endif + + /* HCLK = SYSCLK */ + RCC->CFGR |= (uint32_t)RCC_CFGR_HPRE_DIV1; + + /* PCLK2 = HCLK */ + RCC->CFGR |= (uint32_t)RCC_CFGR_PPRE2_DIV1; + + /* PCLK1 = HCLK */ + RCC->CFGR |= (uint32_t)RCC_CFGR_PPRE1_DIV1; + +#ifdef STM32F10X_CL + /* Configure PLLs ------------------------------------------------------*/ + /* PLL configuration: PLLCLK = PREDIV1 * 6 = 24 MHz */ + RCC->CFGR &= (uint32_t)~(RCC_CFGR_PLLXTPRE | RCC_CFGR_PLLSRC | RCC_CFGR_PLLMULL); + RCC->CFGR |= (uint32_t)(RCC_CFGR_PLLXTPRE_PREDIV1 | RCC_CFGR_PLLSRC_PREDIV1 | + RCC_CFGR_PLLMULL6); + + /* PLL2 configuration: PLL2CLK = (HSE / 5) * 8 = 40 MHz */ + /* PREDIV1 configuration: PREDIV1CLK = PLL2 / 10 = 4 MHz */ + RCC->CFGR2 &= (uint32_t)~(RCC_CFGR2_PREDIV2 | RCC_CFGR2_PLL2MUL | + RCC_CFGR2_PREDIV1 | RCC_CFGR2_PREDIV1SRC); + RCC->CFGR2 |= (uint32_t)(RCC_CFGR2_PREDIV2_DIV5 | RCC_CFGR2_PLL2MUL8 | + RCC_CFGR2_PREDIV1SRC_PLL2 | RCC_CFGR2_PREDIV1_DIV10); + + /* Enable PLL2 */ + RCC->CR |= RCC_CR_PLL2ON; + /* Wait till PLL2 is ready */ + while((RCC->CR & RCC_CR_PLL2RDY) == 0) + { + } +#elif defined (STM32F10X_LD_VL) || defined (STM32F10X_MD_VL) || defined (STM32F10X_HD_VL) + /* PLL configuration: = (HSE / 2) * 6 = 24 MHz */ + RCC->CFGR &= (uint32_t)((uint32_t)~(RCC_CFGR_PLLSRC | RCC_CFGR_PLLXTPRE | RCC_CFGR_PLLMULL)); + RCC->CFGR |= (uint32_t)(RCC_CFGR_PLLSRC_PREDIV1 | RCC_CFGR_PLLXTPRE_PREDIV1_Div2 | RCC_CFGR_PLLMULL6); +#else + /* PLL configuration: = (HSE / 2) * 6 = 24 MHz */ + RCC->CFGR &= (uint32_t)((uint32_t)~(RCC_CFGR_PLLSRC | RCC_CFGR_PLLXTPRE | RCC_CFGR_PLLMULL)); + RCC->CFGR |= (uint32_t)(RCC_CFGR_PLLSRC_HSE | RCC_CFGR_PLLXTPRE_HSE_Div2 | RCC_CFGR_PLLMULL6); +#endif /* STM32F10X_CL */ + + /* Enable PLL */ + RCC->CR |= RCC_CR_PLLON; + + /* Wait till PLL is ready */ + while((RCC->CR & RCC_CR_PLLRDY) == 0) + { + } + + /* Select PLL as system clock source */ + RCC->CFGR &= (uint32_t)((uint32_t)~(RCC_CFGR_SW)); + RCC->CFGR |= (uint32_t)RCC_CFGR_SW_PLL; + + /* Wait till PLL is used as system clock source */ + while ((RCC->CFGR & (uint32_t)RCC_CFGR_SWS) != (uint32_t)0x08) + { + } + } + else + { /* If HSE fails to start-up, the application will have wrong clock + configuration. User can add here some code to deal with this error */ + } +} +#elif defined SYSCLK_FREQ_36MHz +/** + * @brief Sets System clock frequency to 36MHz and configure HCLK, PCLK2 + * and PCLK1 prescalers. + * @note This function should be used only after reset. + * @param None + * @retval None + */ +static void SetSysClockTo36(void) +{ + __IO uint32_t StartUpCounter = 0, HSEStatus = 0; + + /* SYSCLK, HCLK, PCLK2 and PCLK1 configuration ---------------------------*/ + /* Enable HSE */ + RCC->CR |= ((uint32_t)RCC_CR_HSEON); + + /* Wait till HSE is ready and if Time out is reached exit */ + do + { + HSEStatus = RCC->CR & RCC_CR_HSERDY; + StartUpCounter++; + } while((HSEStatus == 0) && (StartUpCounter != HSE_STARTUP_TIMEOUT)); + + if ((RCC->CR & RCC_CR_HSERDY) != RESET) + { + HSEStatus = (uint32_t)0x01; + } + else + { + HSEStatus = (uint32_t)0x00; + } + + if (HSEStatus == (uint32_t)0x01) + { + /* Enable Prefetch Buffer */ + FLASH->ACR |= FLASH_ACR_PRFTBE; + + /* Flash 1 wait state */ + FLASH->ACR &= (uint32_t)((uint32_t)~FLASH_ACR_LATENCY); + FLASH->ACR |= (uint32_t)FLASH_ACR_LATENCY_1; + + /* HCLK = SYSCLK */ + RCC->CFGR |= (uint32_t)RCC_CFGR_HPRE_DIV1; + + /* PCLK2 = HCLK */ + RCC->CFGR |= (uint32_t)RCC_CFGR_PPRE2_DIV1; + + /* PCLK1 = HCLK */ + RCC->CFGR |= (uint32_t)RCC_CFGR_PPRE1_DIV1; + +#ifdef STM32F10X_CL + /* Configure PLLs ------------------------------------------------------*/ + + /* PLL configuration: PLLCLK = PREDIV1 * 9 = 36 MHz */ + RCC->CFGR &= (uint32_t)~(RCC_CFGR_PLLXTPRE | RCC_CFGR_PLLSRC | RCC_CFGR_PLLMULL); + RCC->CFGR |= (uint32_t)(RCC_CFGR_PLLXTPRE_PREDIV1 | RCC_CFGR_PLLSRC_PREDIV1 | + RCC_CFGR_PLLMULL9); + + /*!< PLL2 configuration: PLL2CLK = (HSE / 5) * 8 = 40 MHz */ + /* PREDIV1 configuration: PREDIV1CLK = PLL2 / 10 = 4 MHz */ + + RCC->CFGR2 &= (uint32_t)~(RCC_CFGR2_PREDIV2 | RCC_CFGR2_PLL2MUL | + RCC_CFGR2_PREDIV1 | RCC_CFGR2_PREDIV1SRC); + RCC->CFGR2 |= (uint32_t)(RCC_CFGR2_PREDIV2_DIV5 | RCC_CFGR2_PLL2MUL8 | + RCC_CFGR2_PREDIV1SRC_PLL2 | RCC_CFGR2_PREDIV1_DIV10); + + /* Enable PLL2 */ + RCC->CR |= RCC_CR_PLL2ON; + /* Wait till PLL2 is ready */ + while((RCC->CR & RCC_CR_PLL2RDY) == 0) + { + } + +#else + /* PLL configuration: PLLCLK = (HSE / 2) * 9 = 36 MHz */ + RCC->CFGR &= (uint32_t)((uint32_t)~(RCC_CFGR_PLLSRC | RCC_CFGR_PLLXTPRE | RCC_CFGR_PLLMULL)); + RCC->CFGR |= (uint32_t)(RCC_CFGR_PLLSRC_HSE | RCC_CFGR_PLLXTPRE_HSE_Div2 | RCC_CFGR_PLLMULL9); +#endif /* STM32F10X_CL */ + + /* Enable PLL */ + RCC->CR |= RCC_CR_PLLON; + + /* Wait till PLL is ready */ + while((RCC->CR & RCC_CR_PLLRDY) == 0) + { + } + + /* Select PLL as system clock source */ + RCC->CFGR &= (uint32_t)((uint32_t)~(RCC_CFGR_SW)); + RCC->CFGR |= (uint32_t)RCC_CFGR_SW_PLL; + + /* Wait till PLL is used as system clock source */ + while ((RCC->CFGR & (uint32_t)RCC_CFGR_SWS) != (uint32_t)0x08) + { + } + } + else + { /* If HSE fails to start-up, the application will have wrong clock + configuration. User can add here some code to deal with this error */ + } +} +#elif defined SYSCLK_FREQ_48MHz +/** + * @brief Sets System clock frequency to 48MHz and configure HCLK, PCLK2 + * and PCLK1 prescalers. + * @note This function should be used only after reset. + * @param None + * @retval None + */ +static void SetSysClockTo48(void) +{ + __IO uint32_t StartUpCounter = 0, HSEStatus = 0; + + /* SYSCLK, HCLK, PCLK2 and PCLK1 configuration ---------------------------*/ + /* Enable HSE */ + RCC->CR |= ((uint32_t)RCC_CR_HSEON); + + /* Wait till HSE is ready and if Time out is reached exit */ + do + { + HSEStatus = RCC->CR & RCC_CR_HSERDY; + StartUpCounter++; + } while((HSEStatus == 0) && (StartUpCounter != HSE_STARTUP_TIMEOUT)); + + if ((RCC->CR & RCC_CR_HSERDY) != RESET) + { + HSEStatus = (uint32_t)0x01; + } + else + { + HSEStatus = (uint32_t)0x00; + } + + if (HSEStatus == (uint32_t)0x01) + { + /* Enable Prefetch Buffer */ + FLASH->ACR |= FLASH_ACR_PRFTBE; + + /* Flash 1 wait state */ + FLASH->ACR &= (uint32_t)((uint32_t)~FLASH_ACR_LATENCY); + FLASH->ACR |= (uint32_t)FLASH_ACR_LATENCY_1; + + /* HCLK = SYSCLK */ + RCC->CFGR |= (uint32_t)RCC_CFGR_HPRE_DIV1; + + /* PCLK2 = HCLK */ + RCC->CFGR |= (uint32_t)RCC_CFGR_PPRE2_DIV1; + + /* PCLK1 = HCLK */ + RCC->CFGR |= (uint32_t)RCC_CFGR_PPRE1_DIV2; + +#ifdef STM32F10X_CL + /* Configure PLLs ------------------------------------------------------*/ + /* PLL2 configuration: PLL2CLK = (HSE / 5) * 8 = 40 MHz */ + /* PREDIV1 configuration: PREDIV1CLK = PLL2 / 5 = 8 MHz */ + + RCC->CFGR2 &= (uint32_t)~(RCC_CFGR2_PREDIV2 | RCC_CFGR2_PLL2MUL | + RCC_CFGR2_PREDIV1 | RCC_CFGR2_PREDIV1SRC); + RCC->CFGR2 |= (uint32_t)(RCC_CFGR2_PREDIV2_DIV5 | RCC_CFGR2_PLL2MUL8 | + RCC_CFGR2_PREDIV1SRC_PLL2 | RCC_CFGR2_PREDIV1_DIV5); + + /* Enable PLL2 */ + RCC->CR |= RCC_CR_PLL2ON; + /* Wait till PLL2 is ready */ + while((RCC->CR & RCC_CR_PLL2RDY) == 0) + { + } + + + /* PLL configuration: PLLCLK = PREDIV1 * 6 = 48 MHz */ + RCC->CFGR &= (uint32_t)~(RCC_CFGR_PLLXTPRE | RCC_CFGR_PLLSRC | RCC_CFGR_PLLMULL); + RCC->CFGR |= (uint32_t)(RCC_CFGR_PLLXTPRE_PREDIV1 | RCC_CFGR_PLLSRC_PREDIV1 | + RCC_CFGR_PLLMULL6); +#else + /* PLL configuration: PLLCLK = HSE * 6 = 48 MHz */ + RCC->CFGR &= (uint32_t)((uint32_t)~(RCC_CFGR_PLLSRC | RCC_CFGR_PLLXTPRE | RCC_CFGR_PLLMULL)); + RCC->CFGR |= (uint32_t)(RCC_CFGR_PLLSRC_HSE | RCC_CFGR_PLLMULL6); +#endif /* STM32F10X_CL */ + + /* Enable PLL */ + RCC->CR |= RCC_CR_PLLON; + + /* Wait till PLL is ready */ + while((RCC->CR & RCC_CR_PLLRDY) == 0) + { + } + + /* Select PLL as system clock source */ + RCC->CFGR &= (uint32_t)((uint32_t)~(RCC_CFGR_SW)); + RCC->CFGR |= (uint32_t)RCC_CFGR_SW_PLL; + + /* Wait till PLL is used as system clock source */ + while ((RCC->CFGR & (uint32_t)RCC_CFGR_SWS) != (uint32_t)0x08) + { + } + } + else + { /* If HSE fails to start-up, the application will have wrong clock + configuration. User can add here some code to deal with this error */ + } +} + +#elif defined SYSCLK_FREQ_56MHz +/** + * @brief Sets System clock frequency to 56MHz and configure HCLK, PCLK2 + * and PCLK1 prescalers. + * @note This function should be used only after reset. + * @param None + * @retval None + */ +static void SetSysClockTo56(void) +{ + __IO uint32_t StartUpCounter = 0, HSEStatus = 0; + + /* SYSCLK, HCLK, PCLK2 and PCLK1 configuration ---------------------------*/ + /* Enable HSE */ + RCC->CR |= ((uint32_t)RCC_CR_HSEON); + + /* Wait till HSE is ready and if Time out is reached exit */ + do + { + HSEStatus = RCC->CR & RCC_CR_HSERDY; + StartUpCounter++; + } while((HSEStatus == 0) && (StartUpCounter != HSE_STARTUP_TIMEOUT)); + + if ((RCC->CR & RCC_CR_HSERDY) != RESET) + { + HSEStatus = (uint32_t)0x01; + } + else + { + HSEStatus = (uint32_t)0x00; + } + + if (HSEStatus == (uint32_t)0x01) + { + /* Enable Prefetch Buffer */ + FLASH->ACR |= FLASH_ACR_PRFTBE; + + /* Flash 2 wait state */ + FLASH->ACR &= (uint32_t)((uint32_t)~FLASH_ACR_LATENCY); + FLASH->ACR |= (uint32_t)FLASH_ACR_LATENCY_2; + + /* HCLK = SYSCLK */ + RCC->CFGR |= (uint32_t)RCC_CFGR_HPRE_DIV1; + + /* PCLK2 = HCLK */ + RCC->CFGR |= (uint32_t)RCC_CFGR_PPRE2_DIV1; + + /* PCLK1 = HCLK */ + RCC->CFGR |= (uint32_t)RCC_CFGR_PPRE1_DIV2; + +#ifdef STM32F10X_CL + /* Configure PLLs ------------------------------------------------------*/ + /* PLL2 configuration: PLL2CLK = (HSE / 5) * 8 = 40 MHz */ + /* PREDIV1 configuration: PREDIV1CLK = PLL2 / 5 = 8 MHz */ + + RCC->CFGR2 &= (uint32_t)~(RCC_CFGR2_PREDIV2 | RCC_CFGR2_PLL2MUL | + RCC_CFGR2_PREDIV1 | RCC_CFGR2_PREDIV1SRC); + RCC->CFGR2 |= (uint32_t)(RCC_CFGR2_PREDIV2_DIV5 | RCC_CFGR2_PLL2MUL8 | + RCC_CFGR2_PREDIV1SRC_PLL2 | RCC_CFGR2_PREDIV1_DIV5); + + /* Enable PLL2 */ + RCC->CR |= RCC_CR_PLL2ON; + /* Wait till PLL2 is ready */ + while((RCC->CR & RCC_CR_PLL2RDY) == 0) + { + } + + + /* PLL configuration: PLLCLK = PREDIV1 * 7 = 56 MHz */ + RCC->CFGR &= (uint32_t)~(RCC_CFGR_PLLXTPRE | RCC_CFGR_PLLSRC | RCC_CFGR_PLLMULL); + RCC->CFGR |= (uint32_t)(RCC_CFGR_PLLXTPRE_PREDIV1 | RCC_CFGR_PLLSRC_PREDIV1 | + RCC_CFGR_PLLMULL7); +#else + /* PLL configuration: PLLCLK = HSE * 7 = 56 MHz */ + RCC->CFGR &= (uint32_t)((uint32_t)~(RCC_CFGR_PLLSRC | RCC_CFGR_PLLXTPRE | RCC_CFGR_PLLMULL)); + RCC->CFGR |= (uint32_t)(RCC_CFGR_PLLSRC_HSE | RCC_CFGR_PLLMULL7); + +#endif /* STM32F10X_CL */ + + /* Enable PLL */ + RCC->CR |= RCC_CR_PLLON; + + /* Wait till PLL is ready */ + while((RCC->CR & RCC_CR_PLLRDY) == 0) + { + } + + /* Select PLL as system clock source */ + RCC->CFGR &= (uint32_t)((uint32_t)~(RCC_CFGR_SW)); + RCC->CFGR |= (uint32_t)RCC_CFGR_SW_PLL; + + /* Wait till PLL is used as system clock source */ + while ((RCC->CFGR & (uint32_t)RCC_CFGR_SWS) != (uint32_t)0x08) + { + } + } + else + { /* If HSE fails to start-up, the application will have wrong clock + configuration. User can add here some code to deal with this error */ + } +} + +#elif defined SYSCLK_FREQ_72MHz +/** + * @brief Sets System clock frequency to 72MHz and configure HCLK, PCLK2 + * and PCLK1 prescalers. + * @note This function should be used only after reset. + * @param None + * @retval None + */ +static void SetSysClockTo72(void) +{ + __IO uint32_t StartUpCounter = 0, HSEStatus = 0; + + /* SYSCLK, HCLK, PCLK2 and PCLK1 configuration ---------------------------*/ + /* Enable HSE */ + RCC->CR |= ((uint32_t)RCC_CR_HSEON); + + /* Wait till HSE is ready and if Time out is reached exit */ + do + { + HSEStatus = RCC->CR & RCC_CR_HSERDY; + StartUpCounter++; + } while((HSEStatus == 0) && (StartUpCounter != HSE_STARTUP_TIMEOUT)); + + if ((RCC->CR & RCC_CR_HSERDY) != RESET) + { + HSEStatus = (uint32_t)0x01; + } + else + { + HSEStatus = (uint32_t)0x00; + } + + if (HSEStatus == (uint32_t)0x01) + { + /* Enable Prefetch Buffer */ + FLASH->ACR |= FLASH_ACR_PRFTBE; + + /* Flash 2 wait state */ + FLASH->ACR &= (uint32_t)((uint32_t)~FLASH_ACR_LATENCY); + FLASH->ACR |= (uint32_t)FLASH_ACR_LATENCY_2; + + + /* HCLK = SYSCLK */ + RCC->CFGR |= (uint32_t)RCC_CFGR_HPRE_DIV1; + + /* PCLK2 = HCLK */ + RCC->CFGR |= (uint32_t)RCC_CFGR_PPRE2_DIV1; + + /* PCLK1 = HCLK */ + RCC->CFGR |= (uint32_t)RCC_CFGR_PPRE1_DIV2; + +#ifdef STM32F10X_CL + /* Configure PLLs ------------------------------------------------------*/ + /* PLL2 configuration: PLL2CLK = (HSE / 5) * 8 = 40 MHz */ + /* PREDIV1 configuration: PREDIV1CLK = PLL2 / 5 = 8 MHz */ + + RCC->CFGR2 &= (uint32_t)~(RCC_CFGR2_PREDIV2 | RCC_CFGR2_PLL2MUL | + RCC_CFGR2_PREDIV1 | RCC_CFGR2_PREDIV1SRC); + RCC->CFGR2 |= (uint32_t)(RCC_CFGR2_PREDIV2_DIV5 | RCC_CFGR2_PLL2MUL8 | + RCC_CFGR2_PREDIV1SRC_PLL2 | RCC_CFGR2_PREDIV1_DIV5); + + /* Enable PLL2 */ + RCC->CR |= RCC_CR_PLL2ON; + /* Wait till PLL2 is ready */ + while((RCC->CR & RCC_CR_PLL2RDY) == 0) + { + } + + + /* PLL configuration: PLLCLK = PREDIV1 * 9 = 72 MHz */ + RCC->CFGR &= (uint32_t)~(RCC_CFGR_PLLXTPRE | RCC_CFGR_PLLSRC | RCC_CFGR_PLLMULL); + RCC->CFGR |= (uint32_t)(RCC_CFGR_PLLXTPRE_PREDIV1 | RCC_CFGR_PLLSRC_PREDIV1 | + RCC_CFGR_PLLMULL9); +#else + /* PLL configuration: PLLCLK = HSE * 9 = 72 MHz */ + RCC->CFGR &= (uint32_t)((uint32_t)~(RCC_CFGR_PLLSRC | RCC_CFGR_PLLXTPRE | + RCC_CFGR_PLLMULL)); + RCC->CFGR |= (uint32_t)(RCC_CFGR_PLLSRC_HSE | RCC_CFGR_PLLMULL9); +#endif /* STM32F10X_CL */ + + /* Enable PLL */ + RCC->CR |= RCC_CR_PLLON; + + /* Wait till PLL is ready */ + while((RCC->CR & RCC_CR_PLLRDY) == 0) + { + } + + /* Select PLL as system clock source */ + RCC->CFGR &= (uint32_t)((uint32_t)~(RCC_CFGR_SW)); + RCC->CFGR |= (uint32_t)RCC_CFGR_SW_PLL; + + /* Wait till PLL is used as system clock source */ + while ((RCC->CFGR & (uint32_t)RCC_CFGR_SWS) != (uint32_t)0x08) + { + } + } + else + { /* If HSE fails to start-up, the application will have wrong clock + configuration. User can add here some code to deal with this error */ + } +} +#endif + +/** + * @} + */ + +/** + * @} + */ + +/** + * @} + */ +/******************* (C) COPYRIGHT 2011 STMicroelectronics *****END OF FILE****/ diff --git a/tmp/STM32F10x_StdPeriph_Lib_V3.5.0/Project/STM32F10x_StdPeriph_Examples/DMA/I2C_RAM/main.c b/tmp/STM32F10x_StdPeriph_Lib_V3.5.0/Project/STM32F10x_StdPeriph_Examples/DMA/I2C_RAM/main.c new file mode 100644 index 0000000..56a6480 --- /dev/null +++ b/tmp/STM32F10x_StdPeriph_Lib_V3.5.0/Project/STM32F10x_StdPeriph_Examples/DMA/I2C_RAM/main.c @@ -0,0 +1,256 @@ +/** + ****************************************************************************** + * @file DMA/I2C_RAM/main.c + * @author MCD Application Team + * @version V3.5.0 + * @date 08-April-2011 + * @brief Main program body + ****************************************************************************** + * @attention + * + * THE PRESENT FIRMWARE WHICH IS FOR GUIDANCE ONLY AIMS AT PROVIDING CUSTOMERS + * WITH CODING INFORMATION REGARDING THEIR PRODUCTS IN ORDER FOR THEM TO SAVE + * TIME. AS A RESULT, STMICROELECTRONICS SHALL NOT BE HELD LIABLE FOR ANY + * DIRECT, INDIRECT OR CONSEQUENTIAL DAMAGES WITH RESPECT TO ANY CLAIMS ARISING + * FROM THE CONTENT OF SUCH FIRMWARE AND/OR THE USE MADE BY CUSTOMERS OF THE + * CODING INFORMATION CONTAINED HEREIN IN CONNECTION WITH THEIR PRODUCTS. + * + *

© COPYRIGHT 2011 STMicroelectronics

+ ****************************************************************************** + */ + +/* Includes ------------------------------------------------------------------*/ +#include "stm32f10x.h" + +/** @addtogroup STM32F10x_StdPeriph_Examples + * @{ + */ + +/** @addtogroup DMA_I2C_RAM + * @{ + */ + +/* Private typedef -----------------------------------------------------------*/ +typedef enum { FAILED = 0, PASSED = !FAILED} TestStatus; + +/* Private define ------------------------------------------------------------*/ +#define I2C1_DR_Address 0x40005410 +#define I2C2_DR_Address 0x40005810 +#define I2C1_SLAVE_ADDRESS7 0x30 +#define I2C2_SLAVE_ADDRESS7 0x30 +#define BufferSize 8 +#define ClockSpeed 100000 + +/* Private macro -------------------------------------------------------------*/ +/* Private variables ---------------------------------------------------------*/ +I2C_InitTypeDef I2C_InitStructure; +DMA_InitTypeDef DMA_InitStructure; +uint8_t I2C1_Buffer_Tx[BufferSize] = {1, 2, 3, 4, 5, 6, 7, 8}; +uint8_t I2C2_Buffer_Rx[BufferSize]; +uint8_t Tx_Idx = 0, Rx_Idx = 0; +volatile TestStatus TransferStatus; + +/* Private function prototypes -----------------------------------------------*/ +void RCC_Configuration(void); +void GPIO_Configuration(void); +TestStatus Buffercmp(uint8_t* pBuffer, uint8_t* pBuffer1, uint16_t BufferLength); + +/* Private functions ---------------------------------------------------------*/ + +/** + * @brief Main program + * @param None + * @retval None + */ +int main(void) +{ + /*!< At this stage the microcontroller clock setting is already configured, + this is done through SystemInit() function which is called from startup + file (startup_stm32f10x_xx.s) before to branch to application main. + To reconfigure the default setting of SystemInit() function, refer to + system_stm32f10x.c file + */ + + /* System Clocks Configuration */ + RCC_Configuration(); + + /* Configure the GPIO ports */ + GPIO_Configuration(); + + /* DMA1 channel5 configuration ----------------------------------------------*/ + DMA_DeInit(DMA1_Channel5); + DMA_InitStructure.DMA_PeripheralBaseAddr = (uint32_t)I2C2_DR_Address; + DMA_InitStructure.DMA_MemoryBaseAddr = (uint32_t)I2C2_Buffer_Rx; + DMA_InitStructure.DMA_DIR = DMA_DIR_PeripheralSRC; + DMA_InitStructure.DMA_BufferSize = BufferSize; + DMA_InitStructure.DMA_PeripheralInc = DMA_PeripheralInc_Disable; + DMA_InitStructure.DMA_MemoryInc = DMA_MemoryInc_Enable; + DMA_InitStructure.DMA_PeripheralDataSize = DMA_MemoryDataSize_Byte; + DMA_InitStructure.DMA_MemoryDataSize = DMA_MemoryDataSize_Byte; + DMA_InitStructure.DMA_Mode = DMA_Mode_Normal; + DMA_InitStructure.DMA_Priority = DMA_Priority_VeryHigh; + DMA_InitStructure.DMA_M2M = DMA_M2M_Disable; + DMA_Init(DMA1_Channel5, &DMA_InitStructure); + + /* DMA1 channel6 configuration ----------------------------------------------*/ + DMA_DeInit(DMA1_Channel6); + DMA_InitStructure.DMA_PeripheralBaseAddr = (uint32_t)I2C1_DR_Address; + DMA_InitStructure.DMA_MemoryBaseAddr = (uint32_t)I2C1_Buffer_Tx; + DMA_InitStructure.DMA_DIR = DMA_DIR_PeripheralDST; + DMA_InitStructure.DMA_Priority = DMA_Priority_High; + DMA_Init(DMA1_Channel6, &DMA_InitStructure); + + /* Enable I2C1 and I2C2 ----------------------------------------------------*/ + I2C_Cmd(I2C1, ENABLE); + I2C_Cmd(I2C2, ENABLE); + + /* I2C1 configuration ------------------------------------------------------*/ + I2C_InitStructure.I2C_Mode = I2C_Mode_I2C; + I2C_InitStructure.I2C_DutyCycle = I2C_DutyCycle_2; + I2C_InitStructure.I2C_OwnAddress1 = I2C1_SLAVE_ADDRESS7; + I2C_InitStructure.I2C_Ack = I2C_Ack_Enable; + I2C_InitStructure.I2C_AcknowledgedAddress = I2C_AcknowledgedAddress_7bit; + I2C_InitStructure.I2C_ClockSpeed = ClockSpeed; + I2C_Init(I2C1, &I2C_InitStructure); + /* I2C2 configuration ------------------------------------------------------*/ + I2C_InitStructure.I2C_OwnAddress1 = I2C2_SLAVE_ADDRESS7; + I2C_Init(I2C2, &I2C_InitStructure); + + /*----- Transmission Phase -----*/ + /* Send I2C1 START condition */ + I2C_GenerateSTART(I2C1, ENABLE); + /* Test on I2C1 EV5 and clear it */ + while(!I2C_CheckEvent(I2C1, I2C_EVENT_MASTER_MODE_SELECT)); + /* Send I2C2 slave Address for write */ + I2C_Send7bitAddress(I2C1, I2C2_SLAVE_ADDRESS7, I2C_Direction_Transmitter); + /* Test on I2C2 EV1 and clear it */ + while(!I2C_CheckEvent(I2C2, I2C_EVENT_SLAVE_RECEIVER_ADDRESS_MATCHED)); + /* Test on I2C1 EV6 and clear it */ + while(!I2C_CheckEvent(I2C1, I2C_EVENT_MASTER_TRANSMITTER_MODE_SELECTED)); + + /* Enable I2C2 DMA */ + I2C_DMACmd(I2C2, ENABLE); + /* Enable I2C1 DMA */ + I2C_DMACmd(I2C1, ENABLE); + + /* Enable DMA1 Channel5 */ + DMA_Cmd(DMA1_Channel5, ENABLE); + /* Enable DMA1 Channel6 */ + DMA_Cmd(DMA1_Channel6, ENABLE); + + /* DMA1 Channel5 transfer complete test */ + while(!DMA_GetFlagStatus(DMA1_FLAG_TC5)); + /* DMA1 Channel6 transfer complete test */ + while(!DMA_GetFlagStatus(DMA1_FLAG_TC6)); + + /* Send I2C1 STOP Condition */ + I2C_GenerateSTOP(I2C1, ENABLE); + /* Test on I2C2 EV4 */ + while(!I2C_CheckEvent(I2C2, I2C_EVENT_SLAVE_STOP_DETECTED)); + /* Clear I2C2 STOPF flag: read operation to I2C_SR1 followed by a + write operation to I2C_CR1 */ + (void)(I2C_GetFlagStatus(I2C2, I2C_FLAG_STOPF)); + I2C_Cmd(I2C2, ENABLE); + + + /* Check if the transmitted and received data are equal */ + TransferStatus = Buffercmp(I2C1_Buffer_Tx, I2C2_Buffer_Rx, BufferSize); + /* TransferStatus = PASSED, if the transmitted and received data + are the same */ + /* TransferStatus = FAILED, if the transmitted and received data + are different */ + + while (1) + { + } +} + +/** + * @brief Configures the different system clocks. + * @param None + * @retval None + */ +void RCC_Configuration(void) +{ + /* Enable DMA1 clock */ + RCC_AHBPeriphClockCmd(RCC_AHBPeriph_DMA1, ENABLE); + /* Enable GPIOB clock */ + RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOB, ENABLE); + /* Enable I2C1 and I2C2 clock */ + RCC_APB1PeriphClockCmd(RCC_APB1Periph_I2C1 | RCC_APB1Periph_I2C2, ENABLE); +} + +/** + * @brief Configures the different GPIO ports. + * @param None + * @retval None + */ +void GPIO_Configuration(void) +{ + GPIO_InitTypeDef GPIO_InitStructure; + + /* Configure I2C1 pins: SCL and SDA */ + GPIO_InitStructure.GPIO_Pin = GPIO_Pin_6 | GPIO_Pin_7; + GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz; + GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AF_OD; + GPIO_Init(GPIOB, &GPIO_InitStructure); + + /* Configure I2C2 pins: SCL and SDA */ + GPIO_InitStructure.GPIO_Pin = GPIO_Pin_10 | GPIO_Pin_11; + GPIO_Init(GPIOB, &GPIO_InitStructure); +} + +/** + * @brief Compares two buffers. + * @param pBuffer, pBuffer1: buffers to be compared. + * @param BufferLength: buffer's length + * @retval PASSED: pBuffer identical to pBuffer1 + * FAILED: pBuffer differs from pBuffer1 + */ +TestStatus Buffercmp(uint8_t* pBuffer, uint8_t* pBuffer1, uint16_t BufferLength) +{ + while(BufferLength--) + { + if(*pBuffer != *pBuffer1) + { + return FAILED; + } + + pBuffer++; + pBuffer1++; + } + + return PASSED; +} + +#ifdef USE_FULL_ASSERT + +/** + * @brief Reports the name of the source file and the source line number + * where the assert_param error has occurred. + * @param file: pointer to the source file name + * @param line: assert_param error line source number + * @retval None + */ +void assert_failed(uint8_t* file, uint32_t line) +{ + /* User can add his own implementation to report the file name and line number, + ex: printf("Wrong parameters value: file %s on line %d\r\n", file, line) */ + + /* Infinite loop */ + while (1) + { + } +} + +#endif + +/** + * @} + */ + +/** + * @} + */ + +/******************* (C) COPYRIGHT 2011 STMicroelectronics *****END OF FILE****/ diff --git a/tmp/STM32F10x_StdPeriph_Lib_V3.5.0/Project/STM32F10x_StdPeriph_Examples/DMA/I2C_RAM/readme.txt b/tmp/STM32F10x_StdPeriph_Lib_V3.5.0/Project/STM32F10x_StdPeriph_Examples/DMA/I2C_RAM/readme.txt new file mode 100644 index 0000000..f5118ec --- /dev/null +++ b/tmp/STM32F10x_StdPeriph_Lib_V3.5.0/Project/STM32F10x_StdPeriph_Examples/DMA/I2C_RAM/readme.txt @@ -0,0 +1,103 @@ +/** + @page DMA_I2C_RAM DMA I2C to RAM example + + @verbatim + ******************** (C) COPYRIGHT 2011 STMicroelectronics ******************* + * @file DMA/I2C_RAM/readme.txt + * @author MCD Application Team + * @version V3.5.0 + * @date 08-April-2011 + * @brief Description of the DMA I2C to RAM example. + ****************************************************************************** + * THE PRESENT FIRMWARE WHICH IS FOR GUIDANCE ONLY AIMS AT PROVIDING CUSTOMERS + * WITH CODING INFORMATION REGARDING THEIR PRODUCTS IN ORDER FOR THEM TO SAVE + * TIME. AS A RESULT, STMICROELECTRONICS SHALL NOT BE HELD LIABLE FOR ANY + * DIRECT, INDIRECT OR CONSEQUENTIAL DAMAGES WITH RESPECT TO ANY CLAIMS ARISING + * FROM THE CONTENT OF SUCH FIRMWARE AND/OR THE USE MADE BY CUSTOMERS OF THE + * CODING INFORMATION CONTAINED HEREIN IN CONNECTION WITH THEIR PRODUCTS. + ****************************************************************************** + @endverbatim + +@par Example Description + +This example provides a description of how to use two DMA channels to transfer a +data buffer from memory to I2C2 through I2C1. + +I2C1 is set as the master transmitter and I2C2 as the slave receiver. DMA1 Channel5 is +configured to store the data received from I2C2 into the Rx buffer (reception buffer). +DMA1 Channel6 is configured to transfer data from the Tx buffer (transmission buffer) +to the I2C1 DR register. After the generation of the Start condition and once the slave +address has been acknowledged, DMA capability is enabled for both I2C1 and I2C2. +As soon as the two I2C DMAEN bits are set in the I2C1_CR2 and I2C2_CR2 registers, +the transmission of the Tx buffer is started by DMA1 Channel5 and at the same time the +data received on I2C2 is stored in Rx buffer using DMA1 Channel6 . +The transmitted and the received buffers are compared to check that all data have been +correctly transferred. + + +@par Directory contents + + - DMA/I2C_RAM/stm32f10x_conf.h Library Configuration file + - DMA/I2C_RAM/stm32f10x_it.c Interrupt handlers + - DMA/I2C_RAM/stm32f10x_it.h Interrupt handlers header file + - DMA/I2C_RAM/main.c Main program + - DMA/I2C_RAM/system_stm32f10x.c STM32F10x system source file + + +@par Hardware and Software environment + + - This example runs on STM32F10x Connectivity line, High-Density, Medium-Density, + XL-Density, High-Density Value line, Medium-Density Value line, Low-Density + and Low-Density Value line Devices. + + - This example has been tested with STMicroelectronics STM3210E-EVAL (High-Density + and XL-Density) and STM3210B-EVAL (Medium-Density) evaluation boards and can + be easily tailored to any other supported device and development board. + This example can't be tested with STMicroelectronics STM3210C-EVAL (STM32F10x + Connectivity-Line) evaluation boards since the I2C2 pins (PB10 and PB11) are + already used by Ethernet PHY module. + This example can't be tested with STMicroelectronics STM32100B-EVAL (STM32F10x + Medium-Density Value line) and STM32100E-EVAL (High-Density Value line) + evaluation boards since the I2C1/I2C2 pins (PB6/PB10 and PB7/PB11) are already + used by HDMI-CEC module. + + - STM3210E-EVAL Set-up + - Connect I2C1 SCL pin (PB.06) to I2C2 SCL pin (PB.10) + - Connect I2C1 SDA pin (PB.07) to I2C2 SDA pin (PB.11) + - Check that a pull-up resistor is connected on one I2C SDA pin + - Check that a pull-up resistor is connected on one I2C SCL pin + + - STM3210B-EVAL Set-up + - Connect I2C1 SCL pin (PB.06) to I2C2 SCL pin (PB.10) + - Connect I2C1 SDA pin (PB.07) to I2C2 SDA pin (PB.11) + - Check that a pull-up resistor is connected on one I2C SDA pin + - Check that a pull-up resistor is connected on one I2C SCL pin + +@par How to use it ? + +In order to make the program work, you must do the following : + - Copy all source files from this example folder to the template folder under + Project\STM32F10x_StdPeriph_Template + - Open your preferred toolchain + - Rebuild all files and load your image into target memory + - Run the example + +@note + - Low-density Value line devices are STM32F100xx microcontrollers where the + Flash memory density ranges between 16 and 32 Kbytes. + - Low-density devices are STM32F101xx, STM32F102xx and STM32F103xx + microcontrollers where the Flash memory density ranges between 16 and 32 Kbytes. + - Medium-density Value line devices are STM32F100xx microcontrollers where + the Flash memory density ranges between 64 and 128 Kbytes. + - Medium-density devices are STM32F101xx, STM32F102xx and STM32F103xx + microcontrollers where the Flash memory density ranges between 64 and 128 Kbytes. + - High-density Value line devices are STM32F100xx microcontrollers where + the Flash memory density ranges between 256 and 512 Kbytes. + - High-density devices are STM32F101xx and STM32F103xx microcontrollers where + the Flash memory density ranges between 256 and 512 Kbytes. + - XL-density devices are STM32F101xx and STM32F103xx microcontrollers where + the Flash memory density ranges between 512 and 1024 Kbytes. + - Connectivity line devices are STM32F105xx and STM32F107xx microcontrollers. + + *

© COPYRIGHT 2011 STMicroelectronics

+ */ diff --git a/tmp/STM32F10x_StdPeriph_Lib_V3.5.0/Project/STM32F10x_StdPeriph_Examples/DMA/I2C_RAM/stm32f10x_conf.h b/tmp/STM32F10x_StdPeriph_Lib_V3.5.0/Project/STM32F10x_StdPeriph_Examples/DMA/I2C_RAM/stm32f10x_conf.h new file mode 100644 index 0000000..2926b30 --- /dev/null +++ b/tmp/STM32F10x_StdPeriph_Lib_V3.5.0/Project/STM32F10x_StdPeriph_Examples/DMA/I2C_RAM/stm32f10x_conf.h @@ -0,0 +1,77 @@ +/** + ****************************************************************************** + * @file DMA/I2C_RAM/stm32f10x_conf.h + * @author MCD Application Team + * @version V3.5.0 + * @date 08-April-2011 + * @brief Library configuration file. + ****************************************************************************** + * @attention + * + * THE PRESENT FIRMWARE WHICH IS FOR GUIDANCE ONLY AIMS AT PROVIDING CUSTOMERS + * WITH CODING INFORMATION REGARDING THEIR PRODUCTS IN ORDER FOR THEM TO SAVE + * TIME. AS A RESULT, STMICROELECTRONICS SHALL NOT BE HELD LIABLE FOR ANY + * DIRECT, INDIRECT OR CONSEQUENTIAL DAMAGES WITH RESPECT TO ANY CLAIMS ARISING + * FROM THE CONTENT OF SUCH FIRMWARE AND/OR THE USE MADE BY CUSTOMERS OF THE + * CODING INFORMATION CONTAINED HEREIN IN CONNECTION WITH THEIR PRODUCTS. + * + *

© COPYRIGHT 2011 STMicroelectronics

+ ****************************************************************************** + */ + +/* Define to prevent recursive inclusion -------------------------------------*/ +#ifndef __STM32F10x_CONF_H +#define __STM32F10x_CONF_H + +/* Includes ------------------------------------------------------------------*/ +/* Uncomment/Comment the line below to enable/disable peripheral header file inclusion */ +#include "stm32f10x_adc.h" +#include "stm32f10x_bkp.h" +#include "stm32f10x_can.h" +#include "stm32f10x_cec.h" +#include "stm32f10x_crc.h" +#include "stm32f10x_dac.h" +#include "stm32f10x_dbgmcu.h" +#include "stm32f10x_dma.h" +#include "stm32f10x_exti.h" +#include "stm32f10x_flash.h" +#include "stm32f10x_fsmc.h" +#include "stm32f10x_gpio.h" +#include "stm32f10x_i2c.h" +#include "stm32f10x_iwdg.h" +#include "stm32f10x_pwr.h" +#include "stm32f10x_rcc.h" +#include "stm32f10x_rtc.h" +#include "stm32f10x_sdio.h" +#include "stm32f10x_spi.h" +#include "stm32f10x_tim.h" +#include "stm32f10x_usart.h" +#include "stm32f10x_wwdg.h" +#include "misc.h" /* High level functions for NVIC and SysTick (add-on to CMSIS functions) */ + +/* Exported types ------------------------------------------------------------*/ +/* Exported constants --------------------------------------------------------*/ +/* Uncomment the line below to expanse the "assert_param" macro in the + Standard Peripheral Library drivers code */ +/* #define USE_FULL_ASSERT 1 */ + +/* Exported macro ------------------------------------------------------------*/ +#ifdef USE_FULL_ASSERT + +/** + * @brief The assert_param macro is used for function's parameters check. + * @param expr: If expr is false, it calls assert_failed function which reports + * the name of the source file and the source line number of the call + * that failed. If expr is true, it returns no value. + * @retval None + */ + #define assert_param(expr) ((expr) ? (void)0 : assert_failed((uint8_t *)__FILE__, __LINE__)) +/* Exported functions ------------------------------------------------------- */ + void assert_failed(uint8_t* file, uint32_t line); +#else + #define assert_param(expr) ((void)0) +#endif /* USE_FULL_ASSERT */ + +#endif /* __STM32F10x_CONF_H */ + +/******************* (C) COPYRIGHT 2011 STMicroelectronics *****END OF FILE****/ diff --git a/tmp/STM32F10x_StdPeriph_Lib_V3.5.0/Project/STM32F10x_StdPeriph_Examples/DMA/I2C_RAM/stm32f10x_it.c b/tmp/STM32F10x_StdPeriph_Lib_V3.5.0/Project/STM32F10x_StdPeriph_Examples/DMA/I2C_RAM/stm32f10x_it.c new file mode 100644 index 0000000..9536c56 --- /dev/null +++ b/tmp/STM32F10x_StdPeriph_Lib_V3.5.0/Project/STM32F10x_StdPeriph_Examples/DMA/I2C_RAM/stm32f10x_it.c @@ -0,0 +1,167 @@ +/** + ****************************************************************************** + * @file DMA/I2C_RAM/stm32f10x_it.c + * @author MCD Application Team + * @version V3.5.0 + * @date 08-April-2011 + * @brief Main Interrupt Service Routines. + * This file provides template for all exceptions handler and peripherals + * interrupt service routine. + ****************************************************************************** + * @attention + * + * THE PRESENT FIRMWARE WHICH IS FOR GUIDANCE ONLY AIMS AT PROVIDING CUSTOMERS + * WITH CODING INFORMATION REGARDING THEIR PRODUCTS IN ORDER FOR THEM TO SAVE + * TIME. AS A RESULT, STMICROELECTRONICS SHALL NOT BE HELD LIABLE FOR ANY + * DIRECT, INDIRECT OR CONSEQUENTIAL DAMAGES WITH RESPECT TO ANY CLAIMS ARISING + * FROM THE CONTENT OF SUCH FIRMWARE AND/OR THE USE MADE BY CUSTOMERS OF THE + * CODING INFORMATION CONTAINED HEREIN IN CONNECTION WITH THEIR PRODUCTS. + * + *

© COPYRIGHT 2011 STMicroelectronics

+ ****************************************************************************** + */ + +/* Includes ------------------------------------------------------------------*/ +#include "stm32f10x_it.h" + +/** @addtogroup STM32F10x_StdPeriph_Examples + * @{ + */ + +/** @addtogroup DMA_I2C_RAM + * @{ + */ + +/* Private typedef -----------------------------------------------------------*/ +/* Private define ------------------------------------------------------------*/ +/* Private macro -------------------------------------------------------------*/ +/* Private variables ---------------------------------------------------------*/ +/* Private function prototypes -----------------------------------------------*/ +/* Private functions ---------------------------------------------------------*/ + +/******************************************************************************/ +/* Cortex-M3 Processor Exceptions Handlers */ +/******************************************************************************/ + +/** + * @brief This function handles NMI exception. + * @param None + * @retval None + */ +void NMI_Handler(void) +{ +} + +/** + * @brief This function handles Hard Fault exception. + * @param None + * @retval None + */ +void HardFault_Handler(void) +{ + /* Go to infinite loop when Hard Fault exception occurs */ + while (1) + { + } +} + +/** + * @brief This function handles Memory Manage exception. + * @param None + * @retval None + */ +void MemManage_Handler(void) +{ + /* Go to infinite loop when Memory Manage exception occurs */ + while (1) + { + } +} + +/** + * @brief This function handles Bus Fault exception. + * @param None + * @retval None + */ +void BusFault_Handler(void) +{ + /* Go to infinite loop when Bus Fault exception occurs */ + while (1) + { + } +} + +/** + * @brief This function handles Usage Fault exception. + * @param None + * @retval None + */ +void UsageFault_Handler(void) +{ + /* Go to infinite loop when Usage Fault exception occurs */ + while (1) + { + } +} + +/** + * @brief This function handles SVCall exception. + * @param None + * @retval None + */ +void SVC_Handler(void) +{ +} + +/** + * @brief This function handles Debug Monitor exception. + * @param None + * @retval None + */ +void DebugMon_Handler(void) +{ +} + +/** + * @brief This function handles PendSV_Handler exception. + * @param None + * @retval None + */ +void PendSV_Handler(void) +{ +} + +/** + * @brief This function handles SysTick Handler. + * @param None + * @retval None + */ +void SysTick_Handler(void) +{ +} + +/******************************************************************************/ +/* STM32F10x Peripherals Interrupt Handlers */ +/* Add here the Interrupt Handler for the used peripheral(s) (PPP), for the */ +/* available peripheral interrupt handler's name please refer to the startup */ +/* file (startup_stm32f10x_xx.s). */ +/******************************************************************************/ + +/** + * @brief This function handles PPP interrupt request. + * @param None + * @retval None + */ +/*void PPP_IRQHandler(void) +{ +}*/ + +/** + * @} + */ + +/** + * @} + */ + +/******************* (C) COPYRIGHT 2011 STMicroelectronics *****END OF FILE****/ diff --git a/tmp/STM32F10x_StdPeriph_Lib_V3.5.0/Project/STM32F10x_StdPeriph_Examples/DMA/I2C_RAM/stm32f10x_it.h b/tmp/STM32F10x_StdPeriph_Lib_V3.5.0/Project/STM32F10x_StdPeriph_Examples/DMA/I2C_RAM/stm32f10x_it.h new file mode 100644 index 0000000..94c49d4 --- /dev/null +++ b/tmp/STM32F10x_StdPeriph_Lib_V3.5.0/Project/STM32F10x_StdPeriph_Examples/DMA/I2C_RAM/stm32f10x_it.h @@ -0,0 +1,46 @@ +/** + ****************************************************************************** + * @file DMA/I2C_RAM/stm32f10x_it.h + * @author MCD Application Team + * @version V3.5.0 + * @date 08-April-2011 + * @brief This file contains the headers of the interrupt handlers. + ****************************************************************************** + * @attention + * + * THE PRESENT FIRMWARE WHICH IS FOR GUIDANCE ONLY AIMS AT PROVIDING CUSTOMERS + * WITH CODING INFORMATION REGARDING THEIR PRODUCTS IN ORDER FOR THEM TO SAVE + * TIME. AS A RESULT, STMICROELECTRONICS SHALL NOT BE HELD LIABLE FOR ANY + * DIRECT, INDIRECT OR CONSEQUENTIAL DAMAGES WITH RESPECT TO ANY CLAIMS ARISING + * FROM THE CONTENT OF SUCH FIRMWARE AND/OR THE USE MADE BY CUSTOMERS OF THE + * CODING INFORMATION CONTAINED HEREIN IN CONNECTION WITH THEIR PRODUCTS. + * + *

© COPYRIGHT 2011 STMicroelectronics

+ ****************************************************************************** + */ + +/* Define to prevent recursive inclusion -------------------------------------*/ +#ifndef __STM32F10x_IT_H +#define __STM32F10x_IT_H + +/* Includes ------------------------------------------------------------------*/ +#include "stm32f10x.h" + +/* Exported types ------------------------------------------------------------*/ +/* Exported constants --------------------------------------------------------*/ +/* Exported macro ------------------------------------------------------------*/ +/* Exported functions ------------------------------------------------------- */ + +void NMI_Handler(void); +void HardFault_Handler(void); +void MemManage_Handler(void); +void BusFault_Handler(void); +void UsageFault_Handler(void); +void SVC_Handler(void); +void DebugMon_Handler(void); +void PendSV_Handler(void); +void SysTick_Handler(void); + +#endif /* __STM32F10x_IT_H */ + +/******************* (C) COPYRIGHT 2011 STMicroelectronics *****END OF FILE****/ diff --git a/tmp/STM32F10x_StdPeriph_Lib_V3.5.0/Project/STM32F10x_StdPeriph_Examples/DMA/I2C_RAM/system_stm32f10x.c b/tmp/STM32F10x_StdPeriph_Lib_V3.5.0/Project/STM32F10x_StdPeriph_Examples/DMA/I2C_RAM/system_stm32f10x.c new file mode 100644 index 0000000..f281d1a --- /dev/null +++ b/tmp/STM32F10x_StdPeriph_Lib_V3.5.0/Project/STM32F10x_StdPeriph_Examples/DMA/I2C_RAM/system_stm32f10x.c @@ -0,0 +1,1094 @@ +/** + ****************************************************************************** + * @file DMA/I2C_RAM/system_stm32f10x.c + * @author MCD Application Team + * @version V3.5.0 + * @date 08-April-2011 + * @brief CMSIS Cortex-M3 Device Peripheral Access Layer System Source File. + * + * 1. This file provides two functions and one global variable to be called from + * user application: + * - SystemInit(): Setups the system clock (System clock source, PLL Multiplier + * factors, AHB/APBx prescalers and Flash settings). + * This function is called at startup just after reset and + * before branch to main program. This call is made inside + * the "startup_stm32f10x_xx.s" file. + * + * - SystemCoreClock variable: Contains the core clock (HCLK), it can be used + * by the user application to setup the SysTick + * timer or configure other parameters. + * + * - SystemCoreClockUpdate(): Updates the variable SystemCoreClock and must + * be called whenever the core clock is changed + * during program execution. + * + * 2. After each device reset the HSI (8 MHz) is used as system clock source. + * Then SystemInit() function is called, in "startup_stm32f10x_xx.s" file, to + * configure the system clock before to branch to main program. + * + * 3. If the system clock source selected by user fails to startup, the SystemInit() + * function will do nothing and HSI still used as system clock source. User can + * add some code to deal with this issue inside the SetSysClock() function. + * + * 4. The default value of HSE crystal is set to 8 MHz (or 25 MHz, depedning on + * the product used), refer to "HSE_VALUE" define in "stm32f10x.h" file. + * When HSE is used as system clock source, directly or through PLL, and you + * are using different crystal you have to adapt the HSE value to your own + * configuration. + * + ****************************************************************************** + * @attention + * + * THE PRESENT FIRMWARE WHICH IS FOR GUIDANCE ONLY AIMS AT PROVIDING CUSTOMERS + * WITH CODING INFORMATION REGARDING THEIR PRODUCTS IN ORDER FOR THEM TO SAVE + * TIME. AS A RESULT, STMICROELECTRONICS SHALL NOT BE HELD LIABLE FOR ANY + * DIRECT, INDIRECT OR CONSEQUENTIAL DAMAGES WITH RESPECT TO ANY CLAIMS ARISING + * FROM THE CONTENT OF SUCH FIRMWARE AND/OR THE USE MADE BY CUSTOMERS OF THE + * CODING INFORMATION CONTAINED HEREIN IN CONNECTION WITH THEIR PRODUCTS. + * + *

© COPYRIGHT 2011 STMicroelectronics

+ ****************************************************************************** + */ + +/** @addtogroup CMSIS + * @{ + */ + +/** @addtogroup stm32f10x_system + * @{ + */ + +/** @addtogroup STM32F10x_System_Private_Includes + * @{ + */ + +#include "stm32f10x.h" + +/** + * @} + */ + +/** @addtogroup STM32F10x_System_Private_TypesDefinitions + * @{ + */ + +/** + * @} + */ + +/** @addtogroup STM32F10x_System_Private_Defines + * @{ + */ + +/*!< Uncomment the line corresponding to the desired System clock (SYSCLK) + frequency (after reset the HSI is used as SYSCLK source) + + IMPORTANT NOTE: + ============== + 1. After each device reset the HSI is used as System clock source. + + 2. Please make sure that the selected System clock doesn't exceed your device's + maximum frequency. + + 3. If none of the define below is enabled, the HSI is used as System clock + source. + + 4. The System clock configuration functions provided within this file assume that: + - For Low, Medium and High density Value line devices an external 8MHz + crystal is used to drive the System clock. + - For Low, Medium and High density devices an external 8MHz crystal is + used to drive the System clock. + - For Connectivity line devices an external 25MHz crystal is used to drive + the System clock. + If you are using different crystal you have to adapt those functions accordingly. + */ + +#if defined (STM32F10X_LD_VL) || (defined STM32F10X_MD_VL) || (defined STM32F10X_HD_VL) +/* #define SYSCLK_FREQ_HSE HSE_VALUE */ + #define SYSCLK_FREQ_24MHz 24000000 +#else +/* #define SYSCLK_FREQ_HSE HSE_VALUE */ +/* #define SYSCLK_FREQ_24MHz 24000000 */ +/* #define SYSCLK_FREQ_36MHz 36000000 */ +/* #define SYSCLK_FREQ_48MHz 48000000 */ +/* #define SYSCLK_FREQ_56MHz 56000000 */ +#define SYSCLK_FREQ_72MHz 72000000 +#endif + +/*!< Uncomment the following line if you need to use external SRAM mounted + on STM3210E-EVAL board (STM32 High density and XL-density devices) or on + STM32100E-EVAL board (STM32 High-density value line devices) as data memory */ +#if defined (STM32F10X_HD) || (defined STM32F10X_XL) || (defined STM32F10X_HD_VL) +/* #define DATA_IN_ExtSRAM */ +#endif + +/*!< Uncomment the following line if you need to relocate your vector Table in + Internal SRAM. */ +/* #define VECT_TAB_SRAM */ +#define VECT_TAB_OFFSET 0x0 /*!< Vector Table base offset field. + This value must be a multiple of 0x200. */ + + +/** + * @} + */ + +/** @addtogroup STM32F10x_System_Private_Macros + * @{ + */ + +/** + * @} + */ + +/** @addtogroup STM32F10x_System_Private_Variables + * @{ + */ + +/******************************************************************************* +* Clock Definitions +*******************************************************************************/ +#ifdef SYSCLK_FREQ_HSE + uint32_t SystemCoreClock = SYSCLK_FREQ_HSE; /*!< System Clock Frequency (Core Clock) */ +#elif defined SYSCLK_FREQ_24MHz + uint32_t SystemCoreClock = SYSCLK_FREQ_24MHz; /*!< System Clock Frequency (Core Clock) */ +#elif defined SYSCLK_FREQ_36MHz + uint32_t SystemCoreClock = SYSCLK_FREQ_36MHz; /*!< System Clock Frequency (Core Clock) */ +#elif defined SYSCLK_FREQ_48MHz + uint32_t SystemCoreClock = SYSCLK_FREQ_48MHz; /*!< System Clock Frequency (Core Clock) */ +#elif defined SYSCLK_FREQ_56MHz + uint32_t SystemCoreClock = SYSCLK_FREQ_56MHz; /*!< System Clock Frequency (Core Clock) */ +#elif defined SYSCLK_FREQ_72MHz + uint32_t SystemCoreClock = SYSCLK_FREQ_72MHz; /*!< System Clock Frequency (Core Clock) */ +#else /*!< HSI Selected as System Clock source */ + uint32_t SystemCoreClock = HSI_VALUE; /*!< System Clock Frequency (Core Clock) */ +#endif + +__I uint8_t AHBPrescTable[16] = {0, 0, 0, 0, 0, 0, 0, 0, 1, 2, 3, 4, 6, 7, 8, 9}; +/** + * @} + */ + +/** @addtogroup STM32F10x_System_Private_FunctionPrototypes + * @{ + */ + +static void SetSysClock(void); + +#ifdef SYSCLK_FREQ_HSE + static void SetSysClockToHSE(void); +#elif defined SYSCLK_FREQ_24MHz + static void SetSysClockTo24(void); +#elif defined SYSCLK_FREQ_36MHz + static void SetSysClockTo36(void); +#elif defined SYSCLK_FREQ_48MHz + static void SetSysClockTo48(void); +#elif defined SYSCLK_FREQ_56MHz + static void SetSysClockTo56(void); +#elif defined SYSCLK_FREQ_72MHz + static void SetSysClockTo72(void); +#endif + +#ifdef DATA_IN_ExtSRAM + static void SystemInit_ExtMemCtl(void); +#endif /* DATA_IN_ExtSRAM */ + +/** + * @} + */ + +/** @addtogroup STM32F10x_System_Private_Functions + * @{ + */ + +/** + * @brief Setup the microcontroller system + * Initialize the Embedded Flash Interface, the PLL and update the + * SystemCoreClock variable. + * @note This function should be used only after reset. + * @param None + * @retval None + */ +void SystemInit (void) +{ + /* Reset the RCC clock configuration to the default reset state(for debug purpose) */ + /* Set HSION bit */ + RCC->CR |= (uint32_t)0x00000001; + + /* Reset SW, HPRE, PPRE1, PPRE2, ADCPRE and MCO bits */ +#ifndef STM32F10X_CL + RCC->CFGR &= (uint32_t)0xF8FF0000; +#else + RCC->CFGR &= (uint32_t)0xF0FF0000; +#endif /* STM32F10X_CL */ + + /* Reset HSEON, CSSON and PLLON bits */ + RCC->CR &= (uint32_t)0xFEF6FFFF; + + /* Reset HSEBYP bit */ + RCC->CR &= (uint32_t)0xFFFBFFFF; + + /* Reset PLLSRC, PLLXTPRE, PLLMUL and USBPRE/OTGFSPRE bits */ + RCC->CFGR &= (uint32_t)0xFF80FFFF; + +#ifdef STM32F10X_CL + /* Reset PLL2ON and PLL3ON bits */ + RCC->CR &= (uint32_t)0xEBFFFFFF; + + /* Disable all interrupts and clear pending bits */ + RCC->CIR = 0x00FF0000; + + /* Reset CFGR2 register */ + RCC->CFGR2 = 0x00000000; +#elif defined (STM32F10X_LD_VL) || defined (STM32F10X_MD_VL) || (defined STM32F10X_HD_VL) + /* Disable all interrupts and clear pending bits */ + RCC->CIR = 0x009F0000; + + /* Reset CFGR2 register */ + RCC->CFGR2 = 0x00000000; +#else + /* Disable all interrupts and clear pending bits */ + RCC->CIR = 0x009F0000; +#endif /* STM32F10X_CL */ + +#if defined (STM32F10X_HD) || (defined STM32F10X_XL) || (defined STM32F10X_HD_VL) + #ifdef DATA_IN_ExtSRAM + SystemInit_ExtMemCtl(); + #endif /* DATA_IN_ExtSRAM */ +#endif + + /* Configure the System clock frequency, HCLK, PCLK2 and PCLK1 prescalers */ + /* Configure the Flash Latency cycles and enable prefetch buffer */ + SetSysClock(); + +#ifdef VECT_TAB_SRAM + SCB->VTOR = SRAM_BASE | VECT_TAB_OFFSET; /* Vector Table Relocation in Internal SRAM. */ +#else + SCB->VTOR = FLASH_BASE | VECT_TAB_OFFSET; /* Vector Table Relocation in Internal FLASH. */ +#endif +} + +/** + * @brief Update SystemCoreClock variable according to Clock Register Values. + * The SystemCoreClock variable contains the core clock (HCLK), it can + * be used by the user application to setup the SysTick timer or configure + * other parameters. + * + * @note Each time the core clock (HCLK) changes, this function must be called + * to update SystemCoreClock variable value. Otherwise, any configuration + * based on this variable will be incorrect. + * + * @note - The system frequency computed by this function is not the real + * frequency in the chip. It is calculated based on the predefined + * constant and the selected clock source: + * + * - If SYSCLK source is HSI, SystemCoreClock will contain the HSI_VALUE(*) + * + * - If SYSCLK source is HSE, SystemCoreClock will contain the HSE_VALUE(**) + * + * - If SYSCLK source is PLL, SystemCoreClock will contain the HSE_VALUE(**) + * or HSI_VALUE(*) multiplied by the PLL factors. + * + * (*) HSI_VALUE is a constant defined in stm32f1xx.h file (default value + * 8 MHz) but the real value may vary depending on the variations + * in voltage and temperature. + * + * (**) HSE_VALUE is a constant defined in stm32f1xx.h file (default value + * 8 MHz or 25 MHz, depedning on the product used), user has to ensure + * that HSE_VALUE is same as the real frequency of the crystal used. + * Otherwise, this function may have wrong result. + * + * - The result of this function could be not correct when using fractional + * value for HSE crystal. + * @param None + * @retval None + */ +void SystemCoreClockUpdate (void) +{ + uint32_t tmp = 0, pllmull = 0, pllsource = 0; + +#ifdef STM32F10X_CL + uint32_t prediv1source = 0, prediv1factor = 0, prediv2factor = 0, pll2mull = 0; +#endif /* STM32F10X_CL */ + +#if defined (STM32F10X_LD_VL) || defined (STM32F10X_MD_VL) || (defined STM32F10X_HD_VL) + uint32_t prediv1factor = 0; +#endif /* STM32F10X_LD_VL or STM32F10X_MD_VL or STM32F10X_HD_VL */ + + /* Get SYSCLK source -------------------------------------------------------*/ + tmp = RCC->CFGR & RCC_CFGR_SWS; + + switch (tmp) + { + case 0x00: /* HSI used as system clock */ + SystemCoreClock = HSI_VALUE; + break; + case 0x04: /* HSE used as system clock */ + SystemCoreClock = HSE_VALUE; + break; + case 0x08: /* PLL used as system clock */ + + /* Get PLL clock source and multiplication factor ----------------------*/ + pllmull = RCC->CFGR & RCC_CFGR_PLLMULL; + pllsource = RCC->CFGR & RCC_CFGR_PLLSRC; + +#ifndef STM32F10X_CL + pllmull = ( pllmull >> 18) + 2; + + if (pllsource == 0x00) + { + /* HSI oscillator clock divided by 2 selected as PLL clock entry */ + SystemCoreClock = (HSI_VALUE >> 1) * pllmull; + } + else + { + #if defined (STM32F10X_LD_VL) || defined (STM32F10X_MD_VL) || (defined STM32F10X_HD_VL) + prediv1factor = (RCC->CFGR2 & RCC_CFGR2_PREDIV1) + 1; + /* HSE oscillator clock selected as PREDIV1 clock entry */ + SystemCoreClock = (HSE_VALUE / prediv1factor) * pllmull; + #else + /* HSE selected as PLL clock entry */ + if ((RCC->CFGR & RCC_CFGR_PLLXTPRE) != (uint32_t)RESET) + {/* HSE oscillator clock divided by 2 */ + SystemCoreClock = (HSE_VALUE >> 1) * pllmull; + } + else + { + SystemCoreClock = HSE_VALUE * pllmull; + } + #endif + } +#else + pllmull = pllmull >> 18; + + if (pllmull != 0x0D) + { + pllmull += 2; + } + else + { /* PLL multiplication factor = PLL input clock * 6.5 */ + pllmull = 13 / 2; + } + + if (pllsource == 0x00) + { + /* HSI oscillator clock divided by 2 selected as PLL clock entry */ + SystemCoreClock = (HSI_VALUE >> 1) * pllmull; + } + else + {/* PREDIV1 selected as PLL clock entry */ + + /* Get PREDIV1 clock source and division factor */ + prediv1source = RCC->CFGR2 & RCC_CFGR2_PREDIV1SRC; + prediv1factor = (RCC->CFGR2 & RCC_CFGR2_PREDIV1) + 1; + + if (prediv1source == 0) + { + /* HSE oscillator clock selected as PREDIV1 clock entry */ + SystemCoreClock = (HSE_VALUE / prediv1factor) * pllmull; + } + else + {/* PLL2 clock selected as PREDIV1 clock entry */ + + /* Get PREDIV2 division factor and PLL2 multiplication factor */ + prediv2factor = ((RCC->CFGR2 & RCC_CFGR2_PREDIV2) >> 4) + 1; + pll2mull = ((RCC->CFGR2 & RCC_CFGR2_PLL2MUL) >> 8 ) + 2; + SystemCoreClock = (((HSE_VALUE / prediv2factor) * pll2mull) / prediv1factor) * pllmull; + } + } +#endif /* STM32F10X_CL */ + break; + + default: + SystemCoreClock = HSI_VALUE; + break; + } + + /* Compute HCLK clock frequency ----------------*/ + /* Get HCLK prescaler */ + tmp = AHBPrescTable[((RCC->CFGR & RCC_CFGR_HPRE) >> 4)]; + /* HCLK clock frequency */ + SystemCoreClock >>= tmp; +} + +/** + * @brief Configures the System clock frequency, HCLK, PCLK2 and PCLK1 prescalers. + * @param None + * @retval None + */ +static void SetSysClock(void) +{ +#ifdef SYSCLK_FREQ_HSE + SetSysClockToHSE(); +#elif defined SYSCLK_FREQ_24MHz + SetSysClockTo24(); +#elif defined SYSCLK_FREQ_36MHz + SetSysClockTo36(); +#elif defined SYSCLK_FREQ_48MHz + SetSysClockTo48(); +#elif defined SYSCLK_FREQ_56MHz + SetSysClockTo56(); +#elif defined SYSCLK_FREQ_72MHz + SetSysClockTo72(); +#endif + + /* If none of the define above is enabled, the HSI is used as System clock + source (default after reset) */ +} + +/** + * @brief Setup the external memory controller. Called in startup_stm32f10x.s + * before jump to __main + * @param None + * @retval None + */ +#ifdef DATA_IN_ExtSRAM +/** + * @brief Setup the external memory controller. + * Called in startup_stm32f10x_xx.s/.c before jump to main. + * This function configures the external SRAM mounted on STM3210E-EVAL + * board (STM32 High density devices). This SRAM will be used as program + * data memory (including heap and stack). + * @param None + * @retval None + */ +void SystemInit_ExtMemCtl(void) +{ +/*!< FSMC Bank1 NOR/SRAM3 is used for the STM3210E-EVAL, if another Bank is + required, then adjust the Register Addresses */ + + /* Enable FSMC clock */ + RCC->AHBENR = 0x00000114; + + /* Enable GPIOD, GPIOE, GPIOF and GPIOG clocks */ + RCC->APB2ENR = 0x000001E0; + +/* --------------- SRAM Data lines, NOE and NWE configuration ---------------*/ +/*---------------- SRAM Address lines configuration -------------------------*/ +/*---------------- NOE and NWE configuration --------------------------------*/ +/*---------------- NE3 configuration ----------------------------------------*/ +/*---------------- NBL0, NBL1 configuration ---------------------------------*/ + + GPIOD->CRL = 0x44BB44BB; + GPIOD->CRH = 0xBBBBBBBB; + + GPIOE->CRL = 0xB44444BB; + GPIOE->CRH = 0xBBBBBBBB; + + GPIOF->CRL = 0x44BBBBBB; + GPIOF->CRH = 0xBBBB4444; + + GPIOG->CRL = 0x44BBBBBB; + GPIOG->CRH = 0x44444B44; + +/*---------------- FSMC Configuration ---------------------------------------*/ +/*---------------- Enable FSMC Bank1_SRAM Bank ------------------------------*/ + + FSMC_Bank1->BTCR[4] = 0x00001011; + FSMC_Bank1->BTCR[5] = 0x00000200; +} +#endif /* DATA_IN_ExtSRAM */ + +#ifdef SYSCLK_FREQ_HSE +/** + * @brief Selects HSE as System clock source and configure HCLK, PCLK2 + * and PCLK1 prescalers. + * @note This function should be used only after reset. + * @param None + * @retval None + */ +static void SetSysClockToHSE(void) +{ + __IO uint32_t StartUpCounter = 0, HSEStatus = 0; + + /* SYSCLK, HCLK, PCLK2 and PCLK1 configuration ---------------------------*/ + /* Enable HSE */ + RCC->CR |= ((uint32_t)RCC_CR_HSEON); + + /* Wait till HSE is ready and if Time out is reached exit */ + do + { + HSEStatus = RCC->CR & RCC_CR_HSERDY; + StartUpCounter++; + } while((HSEStatus == 0) && (StartUpCounter != HSE_STARTUP_TIMEOUT)); + + if ((RCC->CR & RCC_CR_HSERDY) != RESET) + { + HSEStatus = (uint32_t)0x01; + } + else + { + HSEStatus = (uint32_t)0x00; + } + + if (HSEStatus == (uint32_t)0x01) + { + +#if !defined STM32F10X_LD_VL && !defined STM32F10X_MD_VL && !defined STM32F10X_HD_VL + /* Enable Prefetch Buffer */ + FLASH->ACR |= FLASH_ACR_PRFTBE; + + /* Flash 0 wait state */ + FLASH->ACR &= (uint32_t)((uint32_t)~FLASH_ACR_LATENCY); + +#ifndef STM32F10X_CL + FLASH->ACR |= (uint32_t)FLASH_ACR_LATENCY_0; +#else + if (HSE_VALUE <= 24000000) + { + FLASH->ACR |= (uint32_t)FLASH_ACR_LATENCY_0; + } + else + { + FLASH->ACR |= (uint32_t)FLASH_ACR_LATENCY_1; + } +#endif /* STM32F10X_CL */ +#endif + + /* HCLK = SYSCLK */ + RCC->CFGR |= (uint32_t)RCC_CFGR_HPRE_DIV1; + + /* PCLK2 = HCLK */ + RCC->CFGR |= (uint32_t)RCC_CFGR_PPRE2_DIV1; + + /* PCLK1 = HCLK */ + RCC->CFGR |= (uint32_t)RCC_CFGR_PPRE1_DIV1; + + /* Select HSE as system clock source */ + RCC->CFGR &= (uint32_t)((uint32_t)~(RCC_CFGR_SW)); + RCC->CFGR |= (uint32_t)RCC_CFGR_SW_HSE; + + /* Wait till HSE is used as system clock source */ + while ((RCC->CFGR & (uint32_t)RCC_CFGR_SWS) != (uint32_t)0x04) + { + } + } + else + { /* If HSE fails to start-up, the application will have wrong clock + configuration. User can add here some code to deal with this error */ + } +} +#elif defined SYSCLK_FREQ_24MHz +/** + * @brief Sets System clock frequency to 24MHz and configure HCLK, PCLK2 + * and PCLK1 prescalers. + * @note This function should be used only after reset. + * @param None + * @retval None + */ +static void SetSysClockTo24(void) +{ + __IO uint32_t StartUpCounter = 0, HSEStatus = 0; + + /* SYSCLK, HCLK, PCLK2 and PCLK1 configuration ---------------------------*/ + /* Enable HSE */ + RCC->CR |= ((uint32_t)RCC_CR_HSEON); + + /* Wait till HSE is ready and if Time out is reached exit */ + do + { + HSEStatus = RCC->CR & RCC_CR_HSERDY; + StartUpCounter++; + } while((HSEStatus == 0) && (StartUpCounter != HSE_STARTUP_TIMEOUT)); + + if ((RCC->CR & RCC_CR_HSERDY) != RESET) + { + HSEStatus = (uint32_t)0x01; + } + else + { + HSEStatus = (uint32_t)0x00; + } + + if (HSEStatus == (uint32_t)0x01) + { +#if !defined STM32F10X_LD_VL && !defined STM32F10X_MD_VL && !defined STM32F10X_HD_VL + /* Enable Prefetch Buffer */ + FLASH->ACR |= FLASH_ACR_PRFTBE; + + /* Flash 0 wait state */ + FLASH->ACR &= (uint32_t)((uint32_t)~FLASH_ACR_LATENCY); + FLASH->ACR |= (uint32_t)FLASH_ACR_LATENCY_0; +#endif + + /* HCLK = SYSCLK */ + RCC->CFGR |= (uint32_t)RCC_CFGR_HPRE_DIV1; + + /* PCLK2 = HCLK */ + RCC->CFGR |= (uint32_t)RCC_CFGR_PPRE2_DIV1; + + /* PCLK1 = HCLK */ + RCC->CFGR |= (uint32_t)RCC_CFGR_PPRE1_DIV1; + +#ifdef STM32F10X_CL + /* Configure PLLs ------------------------------------------------------*/ + /* PLL configuration: PLLCLK = PREDIV1 * 6 = 24 MHz */ + RCC->CFGR &= (uint32_t)~(RCC_CFGR_PLLXTPRE | RCC_CFGR_PLLSRC | RCC_CFGR_PLLMULL); + RCC->CFGR |= (uint32_t)(RCC_CFGR_PLLXTPRE_PREDIV1 | RCC_CFGR_PLLSRC_PREDIV1 | + RCC_CFGR_PLLMULL6); + + /* PLL2 configuration: PLL2CLK = (HSE / 5) * 8 = 40 MHz */ + /* PREDIV1 configuration: PREDIV1CLK = PLL2 / 10 = 4 MHz */ + RCC->CFGR2 &= (uint32_t)~(RCC_CFGR2_PREDIV2 | RCC_CFGR2_PLL2MUL | + RCC_CFGR2_PREDIV1 | RCC_CFGR2_PREDIV1SRC); + RCC->CFGR2 |= (uint32_t)(RCC_CFGR2_PREDIV2_DIV5 | RCC_CFGR2_PLL2MUL8 | + RCC_CFGR2_PREDIV1SRC_PLL2 | RCC_CFGR2_PREDIV1_DIV10); + + /* Enable PLL2 */ + RCC->CR |= RCC_CR_PLL2ON; + /* Wait till PLL2 is ready */ + while((RCC->CR & RCC_CR_PLL2RDY) == 0) + { + } +#elif defined (STM32F10X_LD_VL) || defined (STM32F10X_MD_VL) || defined (STM32F10X_HD_VL) + /* PLL configuration: = (HSE / 2) * 6 = 24 MHz */ + RCC->CFGR &= (uint32_t)((uint32_t)~(RCC_CFGR_PLLSRC | RCC_CFGR_PLLXTPRE | RCC_CFGR_PLLMULL)); + RCC->CFGR |= (uint32_t)(RCC_CFGR_PLLSRC_PREDIV1 | RCC_CFGR_PLLXTPRE_PREDIV1_Div2 | RCC_CFGR_PLLMULL6); +#else + /* PLL configuration: = (HSE / 2) * 6 = 24 MHz */ + RCC->CFGR &= (uint32_t)((uint32_t)~(RCC_CFGR_PLLSRC | RCC_CFGR_PLLXTPRE | RCC_CFGR_PLLMULL)); + RCC->CFGR |= (uint32_t)(RCC_CFGR_PLLSRC_HSE | RCC_CFGR_PLLXTPRE_HSE_Div2 | RCC_CFGR_PLLMULL6); +#endif /* STM32F10X_CL */ + + /* Enable PLL */ + RCC->CR |= RCC_CR_PLLON; + + /* Wait till PLL is ready */ + while((RCC->CR & RCC_CR_PLLRDY) == 0) + { + } + + /* Select PLL as system clock source */ + RCC->CFGR &= (uint32_t)((uint32_t)~(RCC_CFGR_SW)); + RCC->CFGR |= (uint32_t)RCC_CFGR_SW_PLL; + + /* Wait till PLL is used as system clock source */ + while ((RCC->CFGR & (uint32_t)RCC_CFGR_SWS) != (uint32_t)0x08) + { + } + } + else + { /* If HSE fails to start-up, the application will have wrong clock + configuration. User can add here some code to deal with this error */ + } +} +#elif defined SYSCLK_FREQ_36MHz +/** + * @brief Sets System clock frequency to 36MHz and configure HCLK, PCLK2 + * and PCLK1 prescalers. + * @note This function should be used only after reset. + * @param None + * @retval None + */ +static void SetSysClockTo36(void) +{ + __IO uint32_t StartUpCounter = 0, HSEStatus = 0; + + /* SYSCLK, HCLK, PCLK2 and PCLK1 configuration ---------------------------*/ + /* Enable HSE */ + RCC->CR |= ((uint32_t)RCC_CR_HSEON); + + /* Wait till HSE is ready and if Time out is reached exit */ + do + { + HSEStatus = RCC->CR & RCC_CR_HSERDY; + StartUpCounter++; + } while((HSEStatus == 0) && (StartUpCounter != HSE_STARTUP_TIMEOUT)); + + if ((RCC->CR & RCC_CR_HSERDY) != RESET) + { + HSEStatus = (uint32_t)0x01; + } + else + { + HSEStatus = (uint32_t)0x00; + } + + if (HSEStatus == (uint32_t)0x01) + { + /* Enable Prefetch Buffer */ + FLASH->ACR |= FLASH_ACR_PRFTBE; + + /* Flash 1 wait state */ + FLASH->ACR &= (uint32_t)((uint32_t)~FLASH_ACR_LATENCY); + FLASH->ACR |= (uint32_t)FLASH_ACR_LATENCY_1; + + /* HCLK = SYSCLK */ + RCC->CFGR |= (uint32_t)RCC_CFGR_HPRE_DIV1; + + /* PCLK2 = HCLK */ + RCC->CFGR |= (uint32_t)RCC_CFGR_PPRE2_DIV1; + + /* PCLK1 = HCLK */ + RCC->CFGR |= (uint32_t)RCC_CFGR_PPRE1_DIV1; + +#ifdef STM32F10X_CL + /* Configure PLLs ------------------------------------------------------*/ + + /* PLL configuration: PLLCLK = PREDIV1 * 9 = 36 MHz */ + RCC->CFGR &= (uint32_t)~(RCC_CFGR_PLLXTPRE | RCC_CFGR_PLLSRC | RCC_CFGR_PLLMULL); + RCC->CFGR |= (uint32_t)(RCC_CFGR_PLLXTPRE_PREDIV1 | RCC_CFGR_PLLSRC_PREDIV1 | + RCC_CFGR_PLLMULL9); + + /*!< PLL2 configuration: PLL2CLK = (HSE / 5) * 8 = 40 MHz */ + /* PREDIV1 configuration: PREDIV1CLK = PLL2 / 10 = 4 MHz */ + + RCC->CFGR2 &= (uint32_t)~(RCC_CFGR2_PREDIV2 | RCC_CFGR2_PLL2MUL | + RCC_CFGR2_PREDIV1 | RCC_CFGR2_PREDIV1SRC); + RCC->CFGR2 |= (uint32_t)(RCC_CFGR2_PREDIV2_DIV5 | RCC_CFGR2_PLL2MUL8 | + RCC_CFGR2_PREDIV1SRC_PLL2 | RCC_CFGR2_PREDIV1_DIV10); + + /* Enable PLL2 */ + RCC->CR |= RCC_CR_PLL2ON; + /* Wait till PLL2 is ready */ + while((RCC->CR & RCC_CR_PLL2RDY) == 0) + { + } + +#else + /* PLL configuration: PLLCLK = (HSE / 2) * 9 = 36 MHz */ + RCC->CFGR &= (uint32_t)((uint32_t)~(RCC_CFGR_PLLSRC | RCC_CFGR_PLLXTPRE | RCC_CFGR_PLLMULL)); + RCC->CFGR |= (uint32_t)(RCC_CFGR_PLLSRC_HSE | RCC_CFGR_PLLXTPRE_HSE_Div2 | RCC_CFGR_PLLMULL9); +#endif /* STM32F10X_CL */ + + /* Enable PLL */ + RCC->CR |= RCC_CR_PLLON; + + /* Wait till PLL is ready */ + while((RCC->CR & RCC_CR_PLLRDY) == 0) + { + } + + /* Select PLL as system clock source */ + RCC->CFGR &= (uint32_t)((uint32_t)~(RCC_CFGR_SW)); + RCC->CFGR |= (uint32_t)RCC_CFGR_SW_PLL; + + /* Wait till PLL is used as system clock source */ + while ((RCC->CFGR & (uint32_t)RCC_CFGR_SWS) != (uint32_t)0x08) + { + } + } + else + { /* If HSE fails to start-up, the application will have wrong clock + configuration. User can add here some code to deal with this error */ + } +} +#elif defined SYSCLK_FREQ_48MHz +/** + * @brief Sets System clock frequency to 48MHz and configure HCLK, PCLK2 + * and PCLK1 prescalers. + * @note This function should be used only after reset. + * @param None + * @retval None + */ +static void SetSysClockTo48(void) +{ + __IO uint32_t StartUpCounter = 0, HSEStatus = 0; + + /* SYSCLK, HCLK, PCLK2 and PCLK1 configuration ---------------------------*/ + /* Enable HSE */ + RCC->CR |= ((uint32_t)RCC_CR_HSEON); + + /* Wait till HSE is ready and if Time out is reached exit */ + do + { + HSEStatus = RCC->CR & RCC_CR_HSERDY; + StartUpCounter++; + } while((HSEStatus == 0) && (StartUpCounter != HSE_STARTUP_TIMEOUT)); + + if ((RCC->CR & RCC_CR_HSERDY) != RESET) + { + HSEStatus = (uint32_t)0x01; + } + else + { + HSEStatus = (uint32_t)0x00; + } + + if (HSEStatus == (uint32_t)0x01) + { + /* Enable Prefetch Buffer */ + FLASH->ACR |= FLASH_ACR_PRFTBE; + + /* Flash 1 wait state */ + FLASH->ACR &= (uint32_t)((uint32_t)~FLASH_ACR_LATENCY); + FLASH->ACR |= (uint32_t)FLASH_ACR_LATENCY_1; + + /* HCLK = SYSCLK */ + RCC->CFGR |= (uint32_t)RCC_CFGR_HPRE_DIV1; + + /* PCLK2 = HCLK */ + RCC->CFGR |= (uint32_t)RCC_CFGR_PPRE2_DIV1; + + /* PCLK1 = HCLK */ + RCC->CFGR |= (uint32_t)RCC_CFGR_PPRE1_DIV2; + +#ifdef STM32F10X_CL + /* Configure PLLs ------------------------------------------------------*/ + /* PLL2 configuration: PLL2CLK = (HSE / 5) * 8 = 40 MHz */ + /* PREDIV1 configuration: PREDIV1CLK = PLL2 / 5 = 8 MHz */ + + RCC->CFGR2 &= (uint32_t)~(RCC_CFGR2_PREDIV2 | RCC_CFGR2_PLL2MUL | + RCC_CFGR2_PREDIV1 | RCC_CFGR2_PREDIV1SRC); + RCC->CFGR2 |= (uint32_t)(RCC_CFGR2_PREDIV2_DIV5 | RCC_CFGR2_PLL2MUL8 | + RCC_CFGR2_PREDIV1SRC_PLL2 | RCC_CFGR2_PREDIV1_DIV5); + + /* Enable PLL2 */ + RCC->CR |= RCC_CR_PLL2ON; + /* Wait till PLL2 is ready */ + while((RCC->CR & RCC_CR_PLL2RDY) == 0) + { + } + + + /* PLL configuration: PLLCLK = PREDIV1 * 6 = 48 MHz */ + RCC->CFGR &= (uint32_t)~(RCC_CFGR_PLLXTPRE | RCC_CFGR_PLLSRC | RCC_CFGR_PLLMULL); + RCC->CFGR |= (uint32_t)(RCC_CFGR_PLLXTPRE_PREDIV1 | RCC_CFGR_PLLSRC_PREDIV1 | + RCC_CFGR_PLLMULL6); +#else + /* PLL configuration: PLLCLK = HSE * 6 = 48 MHz */ + RCC->CFGR &= (uint32_t)((uint32_t)~(RCC_CFGR_PLLSRC | RCC_CFGR_PLLXTPRE | RCC_CFGR_PLLMULL)); + RCC->CFGR |= (uint32_t)(RCC_CFGR_PLLSRC_HSE | RCC_CFGR_PLLMULL6); +#endif /* STM32F10X_CL */ + + /* Enable PLL */ + RCC->CR |= RCC_CR_PLLON; + + /* Wait till PLL is ready */ + while((RCC->CR & RCC_CR_PLLRDY) == 0) + { + } + + /* Select PLL as system clock source */ + RCC->CFGR &= (uint32_t)((uint32_t)~(RCC_CFGR_SW)); + RCC->CFGR |= (uint32_t)RCC_CFGR_SW_PLL; + + /* Wait till PLL is used as system clock source */ + while ((RCC->CFGR & (uint32_t)RCC_CFGR_SWS) != (uint32_t)0x08) + { + } + } + else + { /* If HSE fails to start-up, the application will have wrong clock + configuration. User can add here some code to deal with this error */ + } +} + +#elif defined SYSCLK_FREQ_56MHz +/** + * @brief Sets System clock frequency to 56MHz and configure HCLK, PCLK2 + * and PCLK1 prescalers. + * @note This function should be used only after reset. + * @param None + * @retval None + */ +static void SetSysClockTo56(void) +{ + __IO uint32_t StartUpCounter = 0, HSEStatus = 0; + + /* SYSCLK, HCLK, PCLK2 and PCLK1 configuration ---------------------------*/ + /* Enable HSE */ + RCC->CR |= ((uint32_t)RCC_CR_HSEON); + + /* Wait till HSE is ready and if Time out is reached exit */ + do + { + HSEStatus = RCC->CR & RCC_CR_HSERDY; + StartUpCounter++; + } while((HSEStatus == 0) && (StartUpCounter != HSE_STARTUP_TIMEOUT)); + + if ((RCC->CR & RCC_CR_HSERDY) != RESET) + { + HSEStatus = (uint32_t)0x01; + } + else + { + HSEStatus = (uint32_t)0x00; + } + + if (HSEStatus == (uint32_t)0x01) + { + /* Enable Prefetch Buffer */ + FLASH->ACR |= FLASH_ACR_PRFTBE; + + /* Flash 2 wait state */ + FLASH->ACR &= (uint32_t)((uint32_t)~FLASH_ACR_LATENCY); + FLASH->ACR |= (uint32_t)FLASH_ACR_LATENCY_2; + + /* HCLK = SYSCLK */ + RCC->CFGR |= (uint32_t)RCC_CFGR_HPRE_DIV1; + + /* PCLK2 = HCLK */ + RCC->CFGR |= (uint32_t)RCC_CFGR_PPRE2_DIV1; + + /* PCLK1 = HCLK */ + RCC->CFGR |= (uint32_t)RCC_CFGR_PPRE1_DIV2; + +#ifdef STM32F10X_CL + /* Configure PLLs ------------------------------------------------------*/ + /* PLL2 configuration: PLL2CLK = (HSE / 5) * 8 = 40 MHz */ + /* PREDIV1 configuration: PREDIV1CLK = PLL2 / 5 = 8 MHz */ + + RCC->CFGR2 &= (uint32_t)~(RCC_CFGR2_PREDIV2 | RCC_CFGR2_PLL2MUL | + RCC_CFGR2_PREDIV1 | RCC_CFGR2_PREDIV1SRC); + RCC->CFGR2 |= (uint32_t)(RCC_CFGR2_PREDIV2_DIV5 | RCC_CFGR2_PLL2MUL8 | + RCC_CFGR2_PREDIV1SRC_PLL2 | RCC_CFGR2_PREDIV1_DIV5); + + /* Enable PLL2 */ + RCC->CR |= RCC_CR_PLL2ON; + /* Wait till PLL2 is ready */ + while((RCC->CR & RCC_CR_PLL2RDY) == 0) + { + } + + + /* PLL configuration: PLLCLK = PREDIV1 * 7 = 56 MHz */ + RCC->CFGR &= (uint32_t)~(RCC_CFGR_PLLXTPRE | RCC_CFGR_PLLSRC | RCC_CFGR_PLLMULL); + RCC->CFGR |= (uint32_t)(RCC_CFGR_PLLXTPRE_PREDIV1 | RCC_CFGR_PLLSRC_PREDIV1 | + RCC_CFGR_PLLMULL7); +#else + /* PLL configuration: PLLCLK = HSE * 7 = 56 MHz */ + RCC->CFGR &= (uint32_t)((uint32_t)~(RCC_CFGR_PLLSRC | RCC_CFGR_PLLXTPRE | RCC_CFGR_PLLMULL)); + RCC->CFGR |= (uint32_t)(RCC_CFGR_PLLSRC_HSE | RCC_CFGR_PLLMULL7); + +#endif /* STM32F10X_CL */ + + /* Enable PLL */ + RCC->CR |= RCC_CR_PLLON; + + /* Wait till PLL is ready */ + while((RCC->CR & RCC_CR_PLLRDY) == 0) + { + } + + /* Select PLL as system clock source */ + RCC->CFGR &= (uint32_t)((uint32_t)~(RCC_CFGR_SW)); + RCC->CFGR |= (uint32_t)RCC_CFGR_SW_PLL; + + /* Wait till PLL is used as system clock source */ + while ((RCC->CFGR & (uint32_t)RCC_CFGR_SWS) != (uint32_t)0x08) + { + } + } + else + { /* If HSE fails to start-up, the application will have wrong clock + configuration. User can add here some code to deal with this error */ + } +} + +#elif defined SYSCLK_FREQ_72MHz +/** + * @brief Sets System clock frequency to 72MHz and configure HCLK, PCLK2 + * and PCLK1 prescalers. + * @note This function should be used only after reset. + * @param None + * @retval None + */ +static void SetSysClockTo72(void) +{ + __IO uint32_t StartUpCounter = 0, HSEStatus = 0; + + /* SYSCLK, HCLK, PCLK2 and PCLK1 configuration ---------------------------*/ + /* Enable HSE */ + RCC->CR |= ((uint32_t)RCC_CR_HSEON); + + /* Wait till HSE is ready and if Time out is reached exit */ + do + { + HSEStatus = RCC->CR & RCC_CR_HSERDY; + StartUpCounter++; + } while((HSEStatus == 0) && (StartUpCounter != HSE_STARTUP_TIMEOUT)); + + if ((RCC->CR & RCC_CR_HSERDY) != RESET) + { + HSEStatus = (uint32_t)0x01; + } + else + { + HSEStatus = (uint32_t)0x00; + } + + if (HSEStatus == (uint32_t)0x01) + { + /* Enable Prefetch Buffer */ + FLASH->ACR |= FLASH_ACR_PRFTBE; + + /* Flash 2 wait state */ + FLASH->ACR &= (uint32_t)((uint32_t)~FLASH_ACR_LATENCY); + FLASH->ACR |= (uint32_t)FLASH_ACR_LATENCY_2; + + + /* HCLK = SYSCLK */ + RCC->CFGR |= (uint32_t)RCC_CFGR_HPRE_DIV1; + + /* PCLK2 = HCLK */ + RCC->CFGR |= (uint32_t)RCC_CFGR_PPRE2_DIV1; + + /* PCLK1 = HCLK */ + RCC->CFGR |= (uint32_t)RCC_CFGR_PPRE1_DIV2; + +#ifdef STM32F10X_CL + /* Configure PLLs ------------------------------------------------------*/ + /* PLL2 configuration: PLL2CLK = (HSE / 5) * 8 = 40 MHz */ + /* PREDIV1 configuration: PREDIV1CLK = PLL2 / 5 = 8 MHz */ + + RCC->CFGR2 &= (uint32_t)~(RCC_CFGR2_PREDIV2 | RCC_CFGR2_PLL2MUL | + RCC_CFGR2_PREDIV1 | RCC_CFGR2_PREDIV1SRC); + RCC->CFGR2 |= (uint32_t)(RCC_CFGR2_PREDIV2_DIV5 | RCC_CFGR2_PLL2MUL8 | + RCC_CFGR2_PREDIV1SRC_PLL2 | RCC_CFGR2_PREDIV1_DIV5); + + /* Enable PLL2 */ + RCC->CR |= RCC_CR_PLL2ON; + /* Wait till PLL2 is ready */ + while((RCC->CR & RCC_CR_PLL2RDY) == 0) + { + } + + + /* PLL configuration: PLLCLK = PREDIV1 * 9 = 72 MHz */ + RCC->CFGR &= (uint32_t)~(RCC_CFGR_PLLXTPRE | RCC_CFGR_PLLSRC | RCC_CFGR_PLLMULL); + RCC->CFGR |= (uint32_t)(RCC_CFGR_PLLXTPRE_PREDIV1 | RCC_CFGR_PLLSRC_PREDIV1 | + RCC_CFGR_PLLMULL9); +#else + /* PLL configuration: PLLCLK = HSE * 9 = 72 MHz */ + RCC->CFGR &= (uint32_t)((uint32_t)~(RCC_CFGR_PLLSRC | RCC_CFGR_PLLXTPRE | + RCC_CFGR_PLLMULL)); + RCC->CFGR |= (uint32_t)(RCC_CFGR_PLLSRC_HSE | RCC_CFGR_PLLMULL9); +#endif /* STM32F10X_CL */ + + /* Enable PLL */ + RCC->CR |= RCC_CR_PLLON; + + /* Wait till PLL is ready */ + while((RCC->CR & RCC_CR_PLLRDY) == 0) + { + } + + /* Select PLL as system clock source */ + RCC->CFGR &= (uint32_t)((uint32_t)~(RCC_CFGR_SW)); + RCC->CFGR |= (uint32_t)RCC_CFGR_SW_PLL; + + /* Wait till PLL is used as system clock source */ + while ((RCC->CFGR & (uint32_t)RCC_CFGR_SWS) != (uint32_t)0x08) + { + } + } + else + { /* If HSE fails to start-up, the application will have wrong clock + configuration. User can add here some code to deal with this error */ + } +} +#endif + +/** + * @} + */ + +/** + * @} + */ + +/** + * @} + */ +/******************* (C) COPYRIGHT 2011 STMicroelectronics *****END OF FILE****/ diff --git a/tmp/STM32F10x_StdPeriph_Lib_V3.5.0/Project/STM32F10x_StdPeriph_Examples/DMA/SPI_RAM/main.c b/tmp/STM32F10x_StdPeriph_Lib_V3.5.0/Project/STM32F10x_StdPeriph_Examples/DMA/SPI_RAM/main.c new file mode 100644 index 0000000..2448236 --- /dev/null +++ b/tmp/STM32F10x_StdPeriph_Lib_V3.5.0/Project/STM32F10x_StdPeriph_Examples/DMA/SPI_RAM/main.c @@ -0,0 +1,358 @@ +/** + ****************************************************************************** + * @file DMA/SPI_RAM/main.c + * @author MCD Application Team + * @version V3.5.0 + * @date 08-April-2011 + * @brief Main program body + ****************************************************************************** + * @attention + * + * THE PRESENT FIRMWARE WHICH IS FOR GUIDANCE ONLY AIMS AT PROVIDING CUSTOMERS + * WITH CODING INFORMATION REGARDING THEIR PRODUCTS IN ORDER FOR THEM TO SAVE + * TIME. AS A RESULT, STMICROELECTRONICS SHALL NOT BE HELD LIABLE FOR ANY + * DIRECT, INDIRECT OR CONSEQUENTIAL DAMAGES WITH RESPECT TO ANY CLAIMS ARISING + * FROM THE CONTENT OF SUCH FIRMWARE AND/OR THE USE MADE BY CUSTOMERS OF THE + * CODING INFORMATION CONTAINED HEREIN IN CONNECTION WITH THEIR PRODUCTS. + * + *

© COPYRIGHT 2011 STMicroelectronics

+ ****************************************************************************** + */ + +/* Includes ------------------------------------------------------------------*/ +#include "stm32f10x.h" +#include "platform_config.h" +#include "stm32_eval.h" + +/** @addtogroup STM32F10x_StdPeriph_Examples + * @{ + */ + +/** @addtogroup DMA_SPI_RAM + * @{ + */ + +/* Private typedef -----------------------------------------------------------*/ +typedef enum { FAILED = 0, PASSED = !FAILED} TestStatus; + +/* Private define ------------------------------------------------------------*/ +#define BufferSize 32 +#define CRCPolynomial 7 + +/* Private macro -------------------------------------------------------------*/ +/* Private variables ---------------------------------------------------------*/ +SPI_InitTypeDef SPI_InitStructure; +DMA_InitTypeDef DMA_InitStructure; +uint8_t SPI_MASTER_Buffer_Rx[BufferSize], SPI_SLAVE_Buffer_Rx[BufferSize]; +volatile uint8_t SPI_MASTERCRCValue = 0, SPI_SLAVECRCValue = 0; +volatile TestStatus TransferStatus1 = FAILED, TransferStatus2 = FAILED; + +uint8_t SPI_MASTER_Buffer_Tx[BufferSize] = {0x01,0x02,0x03,0x04,0x05,0x06,0x07,0x08, + 0x09,0x0A,0x0B,0x0C,0x0D,0x0E,0x0F,0x10, + 0x11,0x12,0x13,0x14,0x15,0x16,0x17,0x18, + 0x19,0x1A,0x1B,0x1C,0x1D,0x1E,0x1F,0x20}; + +uint8_t SPI_SLAVE_Buffer_Tx[BufferSize] = {0x51,0x52,0x53,0x54,0x55,0x56,0x57,0x58, + 0x59,0x5A,0x5B,0x5C,0x5D,0x5E,0x5F,0x60, + 0x61,0x62,0x63,0x64,0x65,0x66,0x67,0x68, + 0x69,0x6A,0x6B,0x6C,0x6D,0x6E,0x6F,0x70}; + +/* Private function prototypes -----------------------------------------------*/ +void RCC_Configuration(void); +void GPIO_Configuration(void); +TestStatus Buffercmp(uint8_t* pBuffer, uint8_t* pBuffer1, uint16_t BufferLength); + +/* Private functions ---------------------------------------------------------*/ + +/** + * @brief Main program + * @param None + * @retval None + */ +int main(void) +{ + /*!< At this stage the microcontroller clock setting is already configured, + this is done through SystemInit() function which is called from startup + file (startup_stm32f10x_xx.s) before to branch to application main. + To reconfigure the default setting of SystemInit() function, refer to + system_stm32f10x.c file + */ + + /* Configure the STM32_EVAL LED */ + STM_EVAL_LEDInit(LED1); + STM_EVAL_LEDInit(LED2); + /* Turn Off LED1 and LED2 */ + STM_EVAL_LEDOff(LED1); + STM_EVAL_LEDOff(LED2); + + /* System Clocks Configuration */ + RCC_Configuration(); + + /* Configure the GPIO ports */ + GPIO_Configuration(); + + /* SPI_MASTER configuration ------------------------------------------------*/ + SPI_InitStructure.SPI_Direction = SPI_Direction_2Lines_FullDuplex; + SPI_InitStructure.SPI_Mode = SPI_Mode_Master; + SPI_InitStructure.SPI_DataSize = SPI_DataSize_8b; + SPI_InitStructure.SPI_CPOL = SPI_CPOL_Low; + SPI_InitStructure.SPI_CPHA = SPI_CPHA_2Edge; + SPI_InitStructure.SPI_NSS = SPI_NSS_Soft; + SPI_InitStructure.SPI_BaudRatePrescaler = SPI_BaudRatePrescaler_8; + SPI_InitStructure.SPI_FirstBit = SPI_FirstBit_MSB; + SPI_InitStructure.SPI_CRCPolynomial = CRCPolynomial; + SPI_Init(SPI_MASTER, &SPI_InitStructure); + + /* SPI_SLAVE configuration -------------------------------------------------*/ + SPI_InitStructure.SPI_Mode = SPI_Mode_Slave; + SPI_Init(SPI_SLAVE, &SPI_InitStructure); + + /* SPI_MASTER_Rx_DMA_Channel configuration ---------------------------------*/ + DMA_DeInit(SPI_MASTER_Rx_DMA_Channel); + DMA_InitStructure.DMA_PeripheralBaseAddr = (uint32_t)SPI_MASTER_DR_Base; + DMA_InitStructure.DMA_MemoryBaseAddr = (uint32_t)SPI_MASTER_Buffer_Rx; + DMA_InitStructure.DMA_DIR = DMA_DIR_PeripheralSRC; + DMA_InitStructure.DMA_BufferSize = BufferSize; + DMA_InitStructure.DMA_PeripheralInc = DMA_PeripheralInc_Disable; + DMA_InitStructure.DMA_MemoryInc = DMA_MemoryInc_Enable; + DMA_InitStructure.DMA_PeripheralDataSize = DMA_PeripheralDataSize_Byte; + DMA_InitStructure.DMA_MemoryDataSize = DMA_MemoryDataSize_Byte; + DMA_InitStructure.DMA_Mode = DMA_Mode_Normal; + DMA_InitStructure.DMA_Priority = DMA_Priority_High; + DMA_InitStructure.DMA_M2M = DMA_M2M_Disable; + DMA_Init(SPI_MASTER_Rx_DMA_Channel, &DMA_InitStructure); + + /* SPI_MASTER_Tx_DMA_Channel configuration ---------------------------------*/ + DMA_DeInit(SPI_MASTER_Tx_DMA_Channel); + DMA_InitStructure.DMA_PeripheralBaseAddr = (uint32_t)SPI_MASTER_DR_Base; + DMA_InitStructure.DMA_MemoryBaseAddr = (uint32_t)SPI_MASTER_Buffer_Tx; + DMA_InitStructure.DMA_DIR = DMA_DIR_PeripheralDST; + DMA_InitStructure.DMA_Priority = DMA_Priority_Low; + DMA_Init(SPI_MASTER_Tx_DMA_Channel, &DMA_InitStructure); + + /* SPI_SLAVE_Rx_DMA_Channel configuration ----------------------------------*/ + DMA_DeInit(SPI_SLAVE_Rx_DMA_Channel); + DMA_InitStructure.DMA_PeripheralBaseAddr = (uint32_t)SPI_SLAVE_DR_Base; + DMA_InitStructure.DMA_MemoryBaseAddr = (uint32_t)SPI_SLAVE_Buffer_Rx; + DMA_InitStructure.DMA_DIR = DMA_DIR_PeripheralSRC; + DMA_InitStructure.DMA_Priority = DMA_Priority_VeryHigh; + DMA_Init(SPI_SLAVE_Rx_DMA_Channel, &DMA_InitStructure); + + /* SPI_SLAVE_Tx_DMA_Channel configuration ----------------------------------*/ + DMA_DeInit(SPI_SLAVE_Tx_DMA_Channel); + DMA_InitStructure.DMA_PeripheralBaseAddr = (uint32_t)SPI_SLAVE_DR_Base; + DMA_InitStructure.DMA_MemoryBaseAddr = (uint32_t)SPI_SLAVE_Buffer_Tx; + DMA_InitStructure.DMA_DIR = DMA_DIR_PeripheralDST; + DMA_InitStructure.DMA_Priority = DMA_Priority_Medium; + DMA_Init(SPI_SLAVE_Tx_DMA_Channel, &DMA_InitStructure); + + /* Enable SPI_MASTER DMA Tx request */ + SPI_I2S_DMACmd(SPI_MASTER, SPI_I2S_DMAReq_Tx, ENABLE); + /* Enable SPI_MASTER DMA Rx request */ + SPI_I2S_DMACmd(SPI_MASTER, SPI_I2S_DMAReq_Rx, ENABLE); + /* Enable SPI_SLAVE DMA Tx request */ + SPI_I2S_DMACmd(SPI_SLAVE, SPI_I2S_DMAReq_Tx, ENABLE); + /* Enable SPI_SLAVE DMA Rx request */ + SPI_I2S_DMACmd(SPI_SLAVE, SPI_I2S_DMAReq_Rx, ENABLE); + + /* Enable SPI_MASTER CRC calculation */ + SPI_CalculateCRC(SPI_MASTER, ENABLE); + /* Enable SPI_SLAVE CRC calculation */ + SPI_CalculateCRC(SPI_SLAVE, ENABLE); + + /* Enable SPI_SLAVE */ + SPI_Cmd(SPI_SLAVE, ENABLE); + /* Enable SPI_MASTER */ + SPI_Cmd(SPI_MASTER, ENABLE); + + /* Enable DMA channels */ + DMA_Cmd(SPI_MASTER_Rx_DMA_Channel, ENABLE); + DMA_Cmd(SPI_SLAVE_Rx_DMA_Channel, ENABLE); + DMA_Cmd(SPI_SLAVE_Tx_DMA_Channel, ENABLE); + DMA_Cmd(SPI_MASTER_Tx_DMA_Channel, ENABLE); + + /* Transfer complete */ + while(!DMA_GetFlagStatus(SPI_MASTER_Rx_DMA_FLAG)); + while(!DMA_GetFlagStatus(SPI_SLAVE_Rx_DMA_FLAG)); + while(!DMA_GetFlagStatus(SPI_SLAVE_Tx_DMA_FLAG)); + while(!DMA_GetFlagStatus(SPI_MASTER_Tx_DMA_FLAG)); + + /* Wait for SPI_MASTER data reception: CRC transmitted by SPI_SLAVE */ + while(SPI_I2S_GetFlagStatus(SPI_MASTER, SPI_I2S_FLAG_RXNE) == RESET); + /* Wait for SPI_SLAVE data reception: CRC transmitted by SPI_MASTER */ + while(SPI_I2S_GetFlagStatus(SPI_SLAVE, SPI_I2S_FLAG_RXNE) == RESET); + + /* Check the correctness of written dada */ + TransferStatus1 = Buffercmp(SPI_SLAVE_Buffer_Rx, SPI_MASTER_Buffer_Tx, BufferSize); + TransferStatus2 = Buffercmp(SPI_MASTER_Buffer_Rx, SPI_SLAVE_Buffer_Tx, BufferSize); + /* TransferStatus1, TransferStatus2 = PASSED, if the data transmitted and received + are correct */ + /* TransferStatus1, TransferStatus2 = FAILED, if the data transmitted and received + are different */ + + /* Test on the SPI_MASTER CRCR ERROR flag */ + if ((SPI_I2S_GetFlagStatus(SPI_MASTER, SPI_FLAG_CRCERR)) != RESET) + { + TransferStatus1 = FAILED; + } + /* Test on the SPI_SLAVE CRCR ERROR flag */ + if ((SPI_I2S_GetFlagStatus(SPI_SLAVE, SPI_FLAG_CRCERR)) != RESET) + { + TransferStatus2 = FAILED; + } + + /* Read SPI_MASTER received CRC value */ + SPI_MASTERCRCValue = SPI_I2S_ReceiveData(SPI_MASTER); + /* Read SPI_SLAVE received CRC value */ + SPI_SLAVECRCValue = SPI_I2S_ReceiveData(SPI_SLAVE); + + if (TransferStatus1 != FAILED) + { + /* OK */ + /* Turn on LD1 */ + STM_EVAL_LEDOn(LED1); + } + else + { + /* KO */ + /* Turn Off LD1 */ + STM_EVAL_LEDOff(LED1); + } + + if (TransferStatus2 != FAILED) + { + /* OK */ + /* Turn on LD2 */ + STM_EVAL_LEDOn(LED2); + } + else + { + /* KO */ + /* Turn Off LD2 */ + STM_EVAL_LEDOff(LED2); + } + + while (1) + { + } +} + +/** + * @brief Configures the different system clocks. + * @param None + * @retval None + */ +void RCC_Configuration(void) +{ + /* PCLK2 = HCLK/2 */ + RCC_PCLK2Config(RCC_HCLK_Div2); + + /* Enable peripheral clocks ------------------------------------------------*/ + /* Enable DMA1 or/and DMA2 clock */ + RCC_AHBPeriphClockCmd(SPI_MASTER_DMA_CLK | SPI_SLAVE_DMA_CLK, ENABLE); + +#ifdef USE_STM3210C_EVAL + /* Enable GPIO clock for SPI_MASTER and SPI_SLAVE */ + RCC_APB2PeriphClockCmd(SPI_MASTER_GPIO_CLK | SPI_SLAVE_GPIO_CLK | + RCC_APB2Periph_AFIO, ENABLE); + + /* Enable SPI_MASTER Periph clock */ + RCC_APB1PeriphClockCmd(SPI_MASTER_CLK, ENABLE); + +#else + /* Enable SPI_MASTER clock and GPIO clock for SPI_MASTER and SPI_SLAVE */ + RCC_APB2PeriphClockCmd(SPI_MASTER_GPIO_CLK | SPI_SLAVE_GPIO_CLK | + SPI_MASTER_CLK, ENABLE); +#endif + /* Enable SPI_SLAVE Periph clock */ + RCC_APB1PeriphClockCmd(SPI_SLAVE_CLK, ENABLE); +} + +/** + * @brief Configures the different GPIO ports. + * @param None + * @retval None + */ +void GPIO_Configuration(void) +{ + GPIO_InitTypeDef GPIO_InitStructure; + +#ifdef USE_STM3210C_EVAL + /* Enable SPI3 Pins Software Remapping */ + GPIO_PinRemapConfig(GPIO_Remap_SPI3, ENABLE); +#endif + + /* Configure SPI_MASTER pins: SCK and MOSI */ + GPIO_InitStructure.GPIO_Pin = SPI_MASTER_PIN_SCK | SPI_MASTER_PIN_MOSI; + GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz; + GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AF_PP; + GPIO_Init(SPI_MASTER_GPIO, &GPIO_InitStructure); + /* Configure SPI_MASTER pins: MISO */ + GPIO_InitStructure.GPIO_Pin = SPI_MASTER_PIN_MISO; + GPIO_InitStructure.GPIO_Mode = GPIO_Mode_IN_FLOATING; + GPIO_Init(SPI_MASTER_GPIO, &GPIO_InitStructure); + + /* Configure SPI_SLAVE pins: SCK and MOSI */ + GPIO_InitStructure.GPIO_Pin = SPI_SLAVE_PIN_SCK | SPI_SLAVE_PIN_MOSI; + GPIO_InitStructure.GPIO_Mode = GPIO_Mode_IN_FLOATING; + GPIO_Init(SPI_SLAVE_GPIO, &GPIO_InitStructure); + /* Configure SPI_SLAVE pins: MISO */ + GPIO_InitStructure.GPIO_Pin = SPI_SLAVE_PIN_MISO ; + GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AF_PP; + GPIO_Init(SPI_SLAVE_GPIO, &GPIO_InitStructure); +} + +/** + * @brief Compares two buffers. + * @param pBuffer, pBuffer1: buffers to be compared. + * @param BufferLength: buffer's length + * @retval PASSED: pBuffer identical to pBuffer1 + * FAILED: pBuffer differs from pBuffer1 + */ +TestStatus Buffercmp(uint8_t* pBuffer, uint8_t* pBuffer1, uint16_t BufferLength) +{ + while(BufferLength--) + { + if(*pBuffer != *pBuffer1) + { + return FAILED; + } + + pBuffer++; + pBuffer1++; + } + + return PASSED; +} + +#ifdef USE_FULL_ASSERT + +/** + * @brief Reports the name of the source file and the source line number + * where the assert_param error has occurred. + * @param file: pointer to the source file name + * @param line: assert_param error line source number + * @retval None + */ +void assert_failed(uint8_t* file, uint32_t line) +{ + /* User can add his own implementation to report the file name and line number, + ex: printf("Wrong parameters value: file %s on line %d\r\n", file, line) */ + + /* Infinite loop */ + while (1) + { + } +} + +#endif + +/** + * @} + */ + +/** + * @} + */ + +/******************* (C) COPYRIGHT 2011 STMicroelectronics *****END OF FILE****/ diff --git a/tmp/STM32F10x_StdPeriph_Lib_V3.5.0/Project/STM32F10x_StdPeriph_Examples/DMA/SPI_RAM/platform_config.h b/tmp/STM32F10x_StdPeriph_Lib_V3.5.0/Project/STM32F10x_StdPeriph_Examples/DMA/SPI_RAM/platform_config.h new file mode 100644 index 0000000..a9e96a5 --- /dev/null +++ b/tmp/STM32F10x_StdPeriph_Lib_V3.5.0/Project/STM32F10x_StdPeriph_Examples/DMA/SPI_RAM/platform_config.h @@ -0,0 +1,110 @@ +/** + ****************************************************************************** + * @file DMA/SPI_RAM/platform_config.h + * @author MCD Application Team + * @version V3.5.0 + * @date 08-April-2011 + * @brief Evaluation board specific configuration file. + ****************************************************************************** + * @attention + * + * THE PRESENT FIRMWARE WHICH IS FOR GUIDANCE ONLY AIMS AT PROVIDING CUSTOMERS + * WITH CODING INFORMATION REGARDING THEIR PRODUCTS IN ORDER FOR THEM TO SAVE + * TIME. AS A RESULT, STMICROELECTRONICS SHALL NOT BE HELD LIABLE FOR ANY + * DIRECT, INDIRECT OR CONSEQUENTIAL DAMAGES WITH RESPECT TO ANY CLAIMS ARISING + * FROM THE CONTENT OF SUCH FIRMWARE AND/OR THE USE MADE BY CUSTOMERS OF THE + * CODING INFORMATION CONTAINED HEREIN IN CONNECTION WITH THEIR PRODUCTS. + * + *

© COPYRIGHT 2011 STMicroelectronics

+ ****************************************************************************** + */ + +/* Define to prevent recursive inclusion -------------------------------------*/ +#ifndef __PLATFORM_CONFIG_H +#define __PLATFORM_CONFIG_H + +/* Includes ------------------------------------------------------------------*/ + +/* Exported types ------------------------------------------------------------*/ +/* Exported constants --------------------------------------------------------*/ +/* Uncomment the line corresponding to the STMicroelectronics evaluation board + used to run the example */ +#if !defined (USE_STM32100E_EVAL) && !defined (USE_STM32100B_EVAL) && !defined (USE_STM3210B_EVAL) && !defined (USE_STM3210E_EVAL) && !defined (USE_STM3210C_EVAL) + //#define USE_STM32100B_EVAL + //#define USE_STM3210B_EVAL + //#define USE_STM3210E_EVAL + //#define USE_STM32100E_EVAL + #define USE_STM3210C_EVAL +#endif + +/* Define the STM32F10x hardware depending on the used evaluation board */ +#if defined (USE_STM3210B_EVAL) || defined (USE_STM3210E_EVAL) || defined(USE_STM32100B_EVAL) || defined (USE_STM32100E_EVAL) + #define SPI_MASTER SPI1 + #define SPI_MASTER_CLK RCC_APB2Periph_SPI1 + #define SPI_MASTER_GPIO GPIOA + #define SPI_MASTER_GPIO_CLK RCC_APB2Periph_GPIOA + #define SPI_MASTER_PIN_SCK GPIO_Pin_5 + #define SPI_MASTER_PIN_MISO GPIO_Pin_6 + #define SPI_MASTER_PIN_MOSI GPIO_Pin_7 + #define SPI_MASTER_DMA DMA1 + #define SPI_MASTER_DMA_CLK RCC_AHBPeriph_DMA1 + #define SPI_MASTER_Rx_DMA_Channel DMA1_Channel2 + #define SPI_MASTER_Rx_DMA_FLAG DMA1_FLAG_TC2 + #define SPI_MASTER_Tx_DMA_Channel DMA1_Channel3 + #define SPI_MASTER_Tx_DMA_FLAG DMA1_FLAG_TC3 + #define SPI_MASTER_DR_Base 0x4001300C + + #define SPI_SLAVE SPI2 + #define SPI_SLAVE_CLK RCC_APB1Periph_SPI2 + #define SPI_SLAVE_GPIO GPIOB + #define SPI_SLAVE_GPIO_CLK RCC_APB2Periph_GPIOB + #define SPI_SLAVE_PIN_SCK GPIO_Pin_13 + #define SPI_SLAVE_PIN_MISO GPIO_Pin_14 + #define SPI_SLAVE_PIN_MOSI GPIO_Pin_15 + #define SPI_SLAVE_DMA DMA1 + #define SPI_SLAVE_DMA_CLK RCC_AHBPeriph_DMA1 + #define SPI_SLAVE_Rx_DMA_Channel DMA1_Channel4 + #define SPI_SLAVE_Rx_DMA_FLAG DMA1_FLAG_TC4 + #define SPI_SLAVE_Tx_DMA_Channel DMA1_Channel5 + #define SPI_SLAVE_Tx_DMA_FLAG DMA1_FLAG_TC5 + #define SPI_SLAVE_DR_Base 0x4000380C + +#elif defined (USE_STM3210C_EVAL) + #define SPI_MASTER SPI3 /* SPI pins are remapped by software */ + #define SPI_MASTER_CLK RCC_APB1Periph_SPI3 + #define SPI_MASTER_GPIO GPIOC + #define SPI_MASTER_GPIO_CLK RCC_APB2Periph_GPIOC + #define SPI_MASTER_PIN_SCK GPIO_Pin_10 + #define SPI_MASTER_PIN_MISO GPIO_Pin_11 + #define SPI_MASTER_PIN_MOSI GPIO_Pin_12 + #define SPI_MASTER_DMA DMA2 + #define SPI_MASTER_DMA_CLK RCC_AHBPeriph_DMA2 + #define SPI_MASTER_Rx_DMA_Channel DMA2_Channel1 + #define SPI_MASTER_Rx_DMA_FLAG DMA2_FLAG_TC1 + #define SPI_MASTER_Tx_DMA_Channel DMA2_Channel2 + #define SPI_MASTER_Tx_DMA_FLAG DMA2_FLAG_TC2 + #define SPI_MASTER_DR_Base 0x40003C0C + + #define SPI_SLAVE SPI2 + #define SPI_SLAVE_CLK RCC_APB1Periph_SPI2 + #define SPI_SLAVE_GPIO GPIOB + #define SPI_SLAVE_GPIO_CLK RCC_APB2Periph_GPIOB + #define SPI_SLAVE_PIN_SCK GPIO_Pin_13 + #define SPI_SLAVE_PIN_MISO GPIO_Pin_14 + #define SPI_SLAVE_PIN_MOSI GPIO_Pin_15 + #define SPI_SLAVE_DMA DMA1 + #define SPI_SLAVE_DMA_CLK RCC_AHBPeriph_DMA1 + #define SPI_SLAVE_Rx_DMA_Channel DMA1_Channel4 + #define SPI_SLAVE_Rx_DMA_FLAG DMA1_FLAG_TC4 + #define SPI_SLAVE_Tx_DMA_Channel DMA1_Channel5 + #define SPI_SLAVE_Tx_DMA_FLAG DMA1_FLAG_TC5 + #define SPI_SLAVE_DR_Base 0x4000380C + +#endif + +/* Exported macro ------------------------------------------------------------*/ +/* Exported functions ------------------------------------------------------- */ + +#endif /* __PLATFORM_CONFIG_H */ + +/******************* (C) COPYRIGHT 2011 STMicroelectronics *****END OF FILE****/ diff --git a/tmp/STM32F10x_StdPeriph_Lib_V3.5.0/Project/STM32F10x_StdPeriph_Examples/DMA/SPI_RAM/readme.txt b/tmp/STM32F10x_StdPeriph_Lib_V3.5.0/Project/STM32F10x_StdPeriph_Examples/DMA/SPI_RAM/readme.txt new file mode 100644 index 0000000..7bcbeb8 --- /dev/null +++ b/tmp/STM32F10x_StdPeriph_Lib_V3.5.0/Project/STM32F10x_StdPeriph_Examples/DMA/SPI_RAM/readme.txt @@ -0,0 +1,121 @@ +/** + @page DMA_SPI_RAM DMA SPI to RAM example + + @verbatim + ******************** (C) COPYRIGHT 2011 STMicroelectronics ******************* + * @file DMA/SPI_RAM/readme.txt + * @author MCD Application Team + * @version V3.5.0 + * @date 08-April-2011 + * @brief Description of the DMA SPI to RAM example. + ****************************************************************************** + * THE PRESENT FIRMWARE WHICH IS FOR GUIDANCE ONLY AIMS AT PROVIDING CUSTOMERS + * WITH CODING INFORMATION REGARDING THEIR PRODUCTS IN ORDER FOR THEM TO SAVE + * TIME. AS A RESULT, STMICROELECTRONICS SHALL NOT BE HELD LIABLE FOR ANY + * DIRECT, INDIRECT OR CONSEQUENTIAL DAMAGES WITH RESPECT TO ANY CLAIMS ARISING + * FROM THE CONTENT OF SUCH FIRMWARE AND/OR THE USE MADE BY CUSTOMERS OF THE + * CODING INFORMATION CONTAINED HEREIN IN CONNECTION WITH THEIR PRODUCTS. + ****************************************************************************** + @endverbatim + +@par Example Description + +This example provides a description of how to use four DMA channels to transfer +a data buffer from memory to SPI_SLAVE through SPI_MASTER and a second data buffer +from memory to SPI_MASTER through SPI_SLAVE in full-duplex mode. +SPI_MASTER and SPI_SLAVE can be SPI1 and SPI2 or SPI3 and SPI2, depending on the +STMicroelectronics EVAL board you are using. + +For each SPI the NSS pin is configured by software (thus NSS pin is free for GPIO use) +and DMA Tx/Rx requests are enabled. + +In this example both transmission and reception are managed through DMA and the +received data are stored into buffers declared in the SRAM. The DMA channels +involved in this transfer depend on the used SPIs (for more details please refer +to platform_config.h file). + +A polling on all Transfer complete flags are done for all used DMA channels to +check the end of all DMA channels transfers. The last received data on SPI_MASTER +and SPI_SLAVE are the CRC values sent by each SPI to the other. +The transmitted and received buffers are compared to check that all data have +been correctly transferred. + + +@par Directory contents + + - DMA/SPI_RAM/platform_config.h Evaluation board specific configuration file + - DMA/SPI_RAM/stm32f10x_conf.h Library Configuration file + - DMA/SPI_RAM/stm32f10x_it.c Interrupt handlers + - DMA/SPI_RAM/stm32f10x_it.h Interrupt handlers header file + - DMA/SPI_RAM/main.c Main program + - DMA/SPI_RAM/system_stm32f10x.c STM32F10x system source file + +@par Hardware and Software environment + + - This example runs on STM32F10x Connectivity line, High-Density, Medium-Density, + XL-Density, High-Density Value line, Medium-Density Value line, Low-Density + and Low-Density Value line Devices. + + - This example has been tested with STMicroelectronics STM32100E-EVAL (High-Density Value line) + STM32100B-EVAL (Medium-Density Value line), STM32100E-EVAL (High-Density Value line), STM3210C-EVAL + (Connectivity line), STM3210E-EVAL (High-Density and XL-Density) and STM3210B-EVAL + (Medium-Density) evaluation boards and can be easily tailored to any other + supported device and development board. + + - STM32100E-EVAL Set-up + - Connect SPI1 SCK pin (PA.05) to SPI2 SCK pin (PB.13) + - Connect SPI1 MISO pin (PA.06) to SPI2 MISO pin (PB.14) + - Connect SPI1 MOSI pin (PA.07) to SPI2 MOSI pin (PB.15) + + - STM32100B-EVAL Set-up + - Connect SPI1 SCK pin (PA.05) to SPI2 SCK pin (PB.13) + - Connect SPI1 MISO pin (PA.06) to SPI2 MISO pin (PB.14) + - Connect SPI1 MOSI pin (PA.07) to SPI2 MOSI pin (PB.15) + + - STM3210C-EVAL Set-up + - Connect SPI3 SCK pin (PC.10) to SPI2 SCK pin (PB.13) + - Connect SPI3 MISO pin (PC.11) to SPI2 MISO pin (PB.14) + - Connect SPI3 MOSI pin (PC.12) to SPI2 MOSI pin (PB.15) + @note In this case SPI3 pins are remapped by software. + + - STM3210E-EVAL Set-up + - Connect SPI1 SCK pin (PA.05) to SPI2 SCK pin (PB.13) + - Connect SPI1 MISO pin (PA.06) to SPI2 MISO pin (PB.14) + - Connect SPI1 MOSI pin (PA.07) to SPI2 MOSI pin (PB.15) + @note The jumper 14 (USB Disconnect) must be set in position 1<->2 in order + to not interfer with SPI2 MISO pin PB14. + + - STM3210B-EVAL Set-up + - Connect SPI1 SCK pin (PA.05) to SPI2 SCK pin (PB.13) + - Connect SPI1 MISO pin (PA.06) to SPI2 MISO pin (PB.14) + - Connect SPI1 MOSI pin (PA.07) to SPI2 MOSI pin (PB.15) + + +@par How to use it ? + +In order to make the program work, you must do the following : + - Copy all source files from this example folder to the template folder under + Project\STM32F10x_StdPeriph_Template + - Open your preferred toolchain + - Rebuild all files and load your image into target memory + - Run the example + +@note + - Low-density Value line devices are STM32F100xx microcontrollers where the + Flash memory density ranges between 16 and 32 Kbytes. + - Low-density devices are STM32F101xx, STM32F102xx and STM32F103xx + microcontrollers where the Flash memory density ranges between 16 and 32 Kbytes. + - Medium-density Value line devices are STM32F100xx microcontrollers where + the Flash memory density ranges between 64 and 128 Kbytes. + - Medium-density devices are STM32F101xx, STM32F102xx and STM32F103xx + microcontrollers where the Flash memory density ranges between 64 and 128 Kbytes. + - High-density Value line devices are STM32F100xx microcontrollers where + the Flash memory density ranges between 256 and 512 Kbytes. + - High-density devices are STM32F101xx and STM32F103xx microcontrollers where + the Flash memory density ranges between 256 and 512 Kbytes. + - XL-density devices are STM32F101xx and STM32F103xx microcontrollers where + the Flash memory density ranges between 512 and 1024 Kbytes. + - Connectivity line devices are STM32F105xx and STM32F107xx microcontrollers. + + *

© COPYRIGHT 2011 STMicroelectronics

+ */ diff --git a/tmp/STM32F10x_StdPeriph_Lib_V3.5.0/Project/STM32F10x_StdPeriph_Examples/DMA/SPI_RAM/stm32f10x_conf.h b/tmp/STM32F10x_StdPeriph_Lib_V3.5.0/Project/STM32F10x_StdPeriph_Examples/DMA/SPI_RAM/stm32f10x_conf.h new file mode 100644 index 0000000..d9edf7c --- /dev/null +++ b/tmp/STM32F10x_StdPeriph_Lib_V3.5.0/Project/STM32F10x_StdPeriph_Examples/DMA/SPI_RAM/stm32f10x_conf.h @@ -0,0 +1,77 @@ +/** + ****************************************************************************** + * @file DMA/SPI_RAM/stm32f10x_conf.h + * @author MCD Application Team + * @version V3.5.0 + * @date 08-April-2011 + * @brief Library configuration file. + ****************************************************************************** + * @attention + * + * THE PRESENT FIRMWARE WHICH IS FOR GUIDANCE ONLY AIMS AT PROVIDING CUSTOMERS + * WITH CODING INFORMATION REGARDING THEIR PRODUCTS IN ORDER FOR THEM TO SAVE + * TIME. AS A RESULT, STMICROELECTRONICS SHALL NOT BE HELD LIABLE FOR ANY + * DIRECT, INDIRECT OR CONSEQUENTIAL DAMAGES WITH RESPECT TO ANY CLAIMS ARISING + * FROM THE CONTENT OF SUCH FIRMWARE AND/OR THE USE MADE BY CUSTOMERS OF THE + * CODING INFORMATION CONTAINED HEREIN IN CONNECTION WITH THEIR PRODUCTS. + * + *

© COPYRIGHT 2011 STMicroelectronics

+ ****************************************************************************** + */ + +/* Define to prevent recursive inclusion -------------------------------------*/ +#ifndef __STM32F10x_CONF_H +#define __STM32F10x_CONF_H + +/* Includes ------------------------------------------------------------------*/ +/* Uncomment/Comment the line below to enable/disable peripheral header file inclusion */ +#include "stm32f10x_adc.h" +#include "stm32f10x_bkp.h" +#include "stm32f10x_can.h" +#include "stm32f10x_cec.h" +#include "stm32f10x_crc.h" +#include "stm32f10x_dac.h" +#include "stm32f10x_dbgmcu.h" +#include "stm32f10x_dma.h" +#include "stm32f10x_exti.h" +#include "stm32f10x_flash.h" +#include "stm32f10x_fsmc.h" +#include "stm32f10x_gpio.h" +#include "stm32f10x_i2c.h" +#include "stm32f10x_iwdg.h" +#include "stm32f10x_pwr.h" +#include "stm32f10x_rcc.h" +#include "stm32f10x_rtc.h" +#include "stm32f10x_sdio.h" +#include "stm32f10x_spi.h" +#include "stm32f10x_tim.h" +#include "stm32f10x_usart.h" +#include "stm32f10x_wwdg.h" +#include "misc.h" /* High level functions for NVIC and SysTick (add-on to CMSIS functions) */ + +/* Exported types ------------------------------------------------------------*/ +/* Exported constants --------------------------------------------------------*/ +/* Uncomment the line below to expanse the "assert_param" macro in the + Standard Peripheral Library drivers code */ +/* #define USE_FULL_ASSERT 1 */ + +/* Exported macro ------------------------------------------------------------*/ +#ifdef USE_FULL_ASSERT + +/** + * @brief The assert_param macro is used for function's parameters check. + * @param expr: If expr is false, it calls assert_failed function which reports + * the name of the source file and the source line number of the call + * that failed. If expr is true, it returns no value. + * @retval None + */ + #define assert_param(expr) ((expr) ? (void)0 : assert_failed((uint8_t *)__FILE__, __LINE__)) +/* Exported functions ------------------------------------------------------- */ + void assert_failed(uint8_t* file, uint32_t line); +#else + #define assert_param(expr) ((void)0) +#endif /* USE_FULL_ASSERT */ + +#endif /* __STM32F10x_CONF_H */ + +/******************* (C) COPYRIGHT 2011 STMicroelectronics *****END OF FILE****/ diff --git a/tmp/STM32F10x_StdPeriph_Lib_V3.5.0/Project/STM32F10x_StdPeriph_Examples/DMA/SPI_RAM/stm32f10x_it.c b/tmp/STM32F10x_StdPeriph_Lib_V3.5.0/Project/STM32F10x_StdPeriph_Examples/DMA/SPI_RAM/stm32f10x_it.c new file mode 100644 index 0000000..758668e --- /dev/null +++ b/tmp/STM32F10x_StdPeriph_Lib_V3.5.0/Project/STM32F10x_StdPeriph_Examples/DMA/SPI_RAM/stm32f10x_it.c @@ -0,0 +1,167 @@ +/** + ****************************************************************************** + * @file DMA/SPI_RAM/stm32f10x_it.c + * @author MCD Application Team + * @version V3.5.0 + * @date 08-April-2011 + * @brief Main Interrupt Service Routines. + * This file provides template for all exceptions handler and peripherals + * interrupt service routine. + ****************************************************************************** + * @attention + * + * THE PRESENT FIRMWARE WHICH IS FOR GUIDANCE ONLY AIMS AT PROVIDING CUSTOMERS + * WITH CODING INFORMATION REGARDING THEIR PRODUCTS IN ORDER FOR THEM TO SAVE + * TIME. AS A RESULT, STMICROELECTRONICS SHALL NOT BE HELD LIABLE FOR ANY + * DIRECT, INDIRECT OR CONSEQUENTIAL DAMAGES WITH RESPECT TO ANY CLAIMS ARISING + * FROM THE CONTENT OF SUCH FIRMWARE AND/OR THE USE MADE BY CUSTOMERS OF THE + * CODING INFORMATION CONTAINED HEREIN IN CONNECTION WITH THEIR PRODUCTS. + * + *

© COPYRIGHT 2011 STMicroelectronics

+ ****************************************************************************** + */ + +/* Includes ------------------------------------------------------------------*/ +#include "stm32f10x_it.h" + +/** @addtogroup STM32F10x_StdPeriph_Examples + * @{ + */ + +/** @addtogroup DMA_SPI_RAM + * @{ + */ + +/* Private typedef -----------------------------------------------------------*/ +/* Private define ------------------------------------------------------------*/ +/* Private macro -------------------------------------------------------------*/ +/* Private variables ---------------------------------------------------------*/ +/* Private function prototypes -----------------------------------------------*/ +/* Private functions ---------------------------------------------------------*/ + +/******************************************************************************/ +/* Cortex-M3 Processor Exceptions Handlers */ +/******************************************************************************/ + +/** + * @brief This function handles NMI exception. + * @param None + * @retval None + */ +void NMI_Handler(void) +{ +} + +/** + * @brief This function handles Hard Fault exception. + * @param None + * @retval None + */ +void HardFault_Handler(void) +{ + /* Go to infinite loop when Hard Fault exception occurs */ + while (1) + { + } +} + +/** + * @brief This function handles Memory Manage exception. + * @param None + * @retval None + */ +void MemManage_Handler(void) +{ + /* Go to infinite loop when Memory Manage exception occurs */ + while (1) + { + } +} + +/** + * @brief This function handles Bus Fault exception. + * @param None + * @retval None + */ +void BusFault_Handler(void) +{ + /* Go to infinite loop when Bus Fault exception occurs */ + while (1) + { + } +} + +/** + * @brief This function handles Usage Fault exception. + * @param None + * @retval None + */ +void UsageFault_Handler(void) +{ + /* Go to infinite loop when Usage Fault exception occurs */ + while (1) + { + } +} + +/** + * @brief This function handles SVCall exception. + * @param None + * @retval None + */ +void SVC_Handler(void) +{ +} + +/** + * @brief This function handles Debug Monitor exception. + * @param None + * @retval None + */ +void DebugMon_Handler(void) +{ +} + +/** + * @brief This function handles PendSV_Handler exception. + * @param None + * @retval None + */ +void PendSV_Handler(void) +{ +} + +/** + * @brief This function handles SysTick Handler. + * @param None + * @retval None + */ +void SysTick_Handler(void) +{ +} + +/******************************************************************************/ +/* STM32F10x Peripherals Interrupt Handlers */ +/* Add here the Interrupt Handler for the used peripheral(s) (PPP), for the */ +/* available peripheral interrupt handler's name please refer to the startup */ +/* file (startup_stm32f10x_xx.s). */ +/******************************************************************************/ + +/** + * @brief This function handles PPP interrupt request. + * @param None + * @retval None + */ +/*void PPP_IRQHandler(void) +{ +}*/ + +/** + * @} + */ + +/** + * @} + */ + +/******************* (C) COPYRIGHT 2011 STMicroelectronics *****END OF FILE****/ diff --git a/tmp/STM32F10x_StdPeriph_Lib_V3.5.0/Project/STM32F10x_StdPeriph_Examples/DMA/SPI_RAM/stm32f10x_it.h b/tmp/STM32F10x_StdPeriph_Lib_V3.5.0/Project/STM32F10x_StdPeriph_Examples/DMA/SPI_RAM/stm32f10x_it.h new file mode 100644 index 0000000..2f4dfa4 --- /dev/null +++ b/tmp/STM32F10x_StdPeriph_Lib_V3.5.0/Project/STM32F10x_StdPeriph_Examples/DMA/SPI_RAM/stm32f10x_it.h @@ -0,0 +1,46 @@ +/** + ****************************************************************************** + * @file DMA/SPI_RAM/stm32f10x_it.h + * @author MCD Application Team + * @version V3.5.0 + * @date 08-April-2011 + * @brief This file contains the headers of the interrupt handlers. + ****************************************************************************** + * @attention + * + * THE PRESENT FIRMWARE WHICH IS FOR GUIDANCE ONLY AIMS AT PROVIDING CUSTOMERS + * WITH CODING INFORMATION REGARDING THEIR PRODUCTS IN ORDER FOR THEM TO SAVE + * TIME. AS A RESULT, STMICROELECTRONICS SHALL NOT BE HELD LIABLE FOR ANY + * DIRECT, INDIRECT OR CONSEQUENTIAL DAMAGES WITH RESPECT TO ANY CLAIMS ARISING + * FROM THE CONTENT OF SUCH FIRMWARE AND/OR THE USE MADE BY CUSTOMERS OF THE + * CODING INFORMATION CONTAINED HEREIN IN CONNECTION WITH THEIR PRODUCTS. + * + *

© COPYRIGHT 2011 STMicroelectronics

+ ****************************************************************************** + */ + +/* Define to prevent recursive inclusion -------------------------------------*/ +#ifndef __STM32F10x_IT_H +#define __STM32F10x_IT_H + +/* Includes ------------------------------------------------------------------*/ +#include "stm32f10x.h" + +/* Exported types ------------------------------------------------------------*/ +/* Exported constants --------------------------------------------------------*/ +/* Exported macro ------------------------------------------------------------*/ +/* Exported functions ------------------------------------------------------- */ + +void NMI_Handler(void); +void HardFault_Handler(void); +void MemManage_Handler(void); +void BusFault_Handler(void); +void UsageFault_Handler(void); +void SVC_Handler(void); +void DebugMon_Handler(void); +void PendSV_Handler(void); +void SysTick_Handler(void); + +#endif /* __STM32F10x_IT_H */ + +/******************* (C) COPYRIGHT 2011 STMicroelectronics *****END OF FILE****/ diff --git a/tmp/STM32F10x_StdPeriph_Lib_V3.5.0/Project/STM32F10x_StdPeriph_Examples/DMA/SPI_RAM/system_stm32f10x.c b/tmp/STM32F10x_StdPeriph_Lib_V3.5.0/Project/STM32F10x_StdPeriph_Examples/DMA/SPI_RAM/system_stm32f10x.c new file mode 100644 index 0000000..33a0bc0 --- /dev/null +++ b/tmp/STM32F10x_StdPeriph_Lib_V3.5.0/Project/STM32F10x_StdPeriph_Examples/DMA/SPI_RAM/system_stm32f10x.c @@ -0,0 +1,1094 @@ +/** + ****************************************************************************** + * @file DMA/SPI_RAM/system_stm32f10x.c + * @author MCD Application Team + * @version V3.5.0 + * @date 08-April-2011 + * @brief CMSIS Cortex-M3 Device Peripheral Access Layer System Source File. + * + * 1. This file provides two functions and one global variable to be called from + * user application: + * - SystemInit(): Setups the system clock (System clock source, PLL Multiplier + * factors, AHB/APBx prescalers and Flash settings). + * This function is called at startup just after reset and + * before branch to main program. This call is made inside + * the "startup_stm32f10x_xx.s" file. + * + * - SystemCoreClock variable: Contains the core clock (HCLK), it can be used + * by the user application to setup the SysTick + * timer or configure other parameters. + * + * - SystemCoreClockUpdate(): Updates the variable SystemCoreClock and must + * be called whenever the core clock is changed + * during program execution. + * + * 2. After each device reset the HSI (8 MHz) is used as system clock source. + * Then SystemInit() function is called, in "startup_stm32f10x_xx.s" file, to + * configure the system clock before to branch to main program. + * + * 3. If the system clock source selected by user fails to startup, the SystemInit() + * function will do nothing and HSI still used as system clock source. User can + * add some code to deal with this issue inside the SetSysClock() function. + * + * 4. The default value of HSE crystal is set to 8 MHz (or 25 MHz, depedning on + * the product used), refer to "HSE_VALUE" define in "stm32f10x.h" file. + * When HSE is used as system clock source, directly or through PLL, and you + * are using different crystal you have to adapt the HSE value to your own + * configuration. + * + ****************************************************************************** + * @attention + * + * THE PRESENT FIRMWARE WHICH IS FOR GUIDANCE ONLY AIMS AT PROVIDING CUSTOMERS + * WITH CODING INFORMATION REGARDING THEIR PRODUCTS IN ORDER FOR THEM TO SAVE + * TIME. AS A RESULT, STMICROELECTRONICS SHALL NOT BE HELD LIABLE FOR ANY + * DIRECT, INDIRECT OR CONSEQUENTIAL DAMAGES WITH RESPECT TO ANY CLAIMS ARISING + * FROM THE CONTENT OF SUCH FIRMWARE AND/OR THE USE MADE BY CUSTOMERS OF THE + * CODING INFORMATION CONTAINED HEREIN IN CONNECTION WITH THEIR PRODUCTS. + * + *

© COPYRIGHT 2011 STMicroelectronics

+ ****************************************************************************** + */ + +/** @addtogroup CMSIS + * @{ + */ + +/** @addtogroup stm32f10x_system + * @{ + */ + +/** @addtogroup STM32F10x_System_Private_Includes + * @{ + */ + +#include "stm32f10x.h" + +/** + * @} + */ + +/** @addtogroup STM32F10x_System_Private_TypesDefinitions + * @{ + */ + +/** + * @} + */ + +/** @addtogroup STM32F10x_System_Private_Defines + * @{ + */ + +/*!< Uncomment the line corresponding to the desired System clock (SYSCLK) + frequency (after reset the HSI is used as SYSCLK source) + + IMPORTANT NOTE: + ============== + 1. After each device reset the HSI is used as System clock source. + + 2. Please make sure that the selected System clock doesn't exceed your device's + maximum frequency. + + 3. If none of the define below is enabled, the HSI is used as System clock + source. + + 4. The System clock configuration functions provided within this file assume that: + - For Low, Medium and High density Value line devices an external 8MHz + crystal is used to drive the System clock. + - For Low, Medium and High density devices an external 8MHz crystal is + used to drive the System clock. + - For Connectivity line devices an external 25MHz crystal is used to drive + the System clock. + If you are using different crystal you have to adapt those functions accordingly. + */ + +#if defined (STM32F10X_LD_VL) || (defined STM32F10X_MD_VL) || (defined STM32F10X_HD_VL) +/* #define SYSCLK_FREQ_HSE HSE_VALUE */ + #define SYSCLK_FREQ_24MHz 24000000 +#else +/* #define SYSCLK_FREQ_HSE HSE_VALUE */ +/* #define SYSCLK_FREQ_24MHz 24000000 */ +/* #define SYSCLK_FREQ_36MHz 36000000 */ +/* #define SYSCLK_FREQ_48MHz 48000000 */ +/* #define SYSCLK_FREQ_56MHz 56000000 */ +#define SYSCLK_FREQ_72MHz 72000000 +#endif + +/*!< Uncomment the following line if you need to use external SRAM mounted + on STM3210E-EVAL board (STM32 High density and XL-density devices) or on + STM32100E-EVAL board (STM32 High-density value line devices) as data memory */ +#if defined (STM32F10X_HD) || (defined STM32F10X_XL) || (defined STM32F10X_HD_VL) +/* #define DATA_IN_ExtSRAM */ +#endif + +/*!< Uncomment the following line if you need to relocate your vector Table in + Internal SRAM. */ +/* #define VECT_TAB_SRAM */ +#define VECT_TAB_OFFSET 0x0 /*!< Vector Table base offset field. + This value must be a multiple of 0x200. */ + + +/** + * @} + */ + +/** @addtogroup STM32F10x_System_Private_Macros + * @{ + */ + +/** + * @} + */ + +/** @addtogroup STM32F10x_System_Private_Variables + * @{ + */ + +/******************************************************************************* +* Clock Definitions +*******************************************************************************/ +#ifdef SYSCLK_FREQ_HSE + uint32_t SystemCoreClock = SYSCLK_FREQ_HSE; /*!< System Clock Frequency (Core Clock) */ +#elif defined SYSCLK_FREQ_24MHz + uint32_t SystemCoreClock = SYSCLK_FREQ_24MHz; /*!< System Clock Frequency (Core Clock) */ +#elif defined SYSCLK_FREQ_36MHz + uint32_t SystemCoreClock = SYSCLK_FREQ_36MHz; /*!< System Clock Frequency (Core Clock) */ +#elif defined SYSCLK_FREQ_48MHz + uint32_t SystemCoreClock = SYSCLK_FREQ_48MHz; /*!< System Clock Frequency (Core Clock) */ +#elif defined SYSCLK_FREQ_56MHz + uint32_t SystemCoreClock = SYSCLK_FREQ_56MHz; /*!< System Clock Frequency (Core Clock) */ +#elif defined SYSCLK_FREQ_72MHz + uint32_t SystemCoreClock = SYSCLK_FREQ_72MHz; /*!< System Clock Frequency (Core Clock) */ +#else /*!< HSI Selected as System Clock source */ + uint32_t SystemCoreClock = HSI_VALUE; /*!< System Clock Frequency (Core Clock) */ +#endif + +__I uint8_t AHBPrescTable[16] = {0, 0, 0, 0, 0, 0, 0, 0, 1, 2, 3, 4, 6, 7, 8, 9}; +/** + * @} + */ + +/** @addtogroup STM32F10x_System_Private_FunctionPrototypes + * @{ + */ + +static void SetSysClock(void); + +#ifdef SYSCLK_FREQ_HSE + static void SetSysClockToHSE(void); +#elif defined SYSCLK_FREQ_24MHz + static void SetSysClockTo24(void); +#elif defined SYSCLK_FREQ_36MHz + static void SetSysClockTo36(void); +#elif defined SYSCLK_FREQ_48MHz + static void SetSysClockTo48(void); +#elif defined SYSCLK_FREQ_56MHz + static void SetSysClockTo56(void); +#elif defined SYSCLK_FREQ_72MHz + static void SetSysClockTo72(void); +#endif + +#ifdef DATA_IN_ExtSRAM + static void SystemInit_ExtMemCtl(void); +#endif /* DATA_IN_ExtSRAM */ + +/** + * @} + */ + +/** @addtogroup STM32F10x_System_Private_Functions + * @{ + */ + +/** + * @brief Setup the microcontroller system + * Initialize the Embedded Flash Interface, the PLL and update the + * SystemCoreClock variable. + * @note This function should be used only after reset. + * @param None + * @retval None + */ +void SystemInit (void) +{ + /* Reset the RCC clock configuration to the default reset state(for debug purpose) */ + /* Set HSION bit */ + RCC->CR |= (uint32_t)0x00000001; + + /* Reset SW, HPRE, PPRE1, PPRE2, ADCPRE and MCO bits */ +#ifndef STM32F10X_CL + RCC->CFGR &= (uint32_t)0xF8FF0000; +#else + RCC->CFGR &= (uint32_t)0xF0FF0000; +#endif /* STM32F10X_CL */ + + /* Reset HSEON, CSSON and PLLON bits */ + RCC->CR &= (uint32_t)0xFEF6FFFF; + + /* Reset HSEBYP bit */ + RCC->CR &= (uint32_t)0xFFFBFFFF; + + /* Reset PLLSRC, PLLXTPRE, PLLMUL and USBPRE/OTGFSPRE bits */ + RCC->CFGR &= (uint32_t)0xFF80FFFF; + +#ifdef STM32F10X_CL + /* Reset PLL2ON and PLL3ON bits */ + RCC->CR &= (uint32_t)0xEBFFFFFF; + + /* Disable all interrupts and clear pending bits */ + RCC->CIR = 0x00FF0000; + + /* Reset CFGR2 register */ + RCC->CFGR2 = 0x00000000; +#elif defined (STM32F10X_LD_VL) || defined (STM32F10X_MD_VL) || (defined STM32F10X_HD_VL) + /* Disable all interrupts and clear pending bits */ + RCC->CIR = 0x009F0000; + + /* Reset CFGR2 register */ + RCC->CFGR2 = 0x00000000; +#else + /* Disable all interrupts and clear pending bits */ + RCC->CIR = 0x009F0000; +#endif /* STM32F10X_CL */ + +#if defined (STM32F10X_HD) || (defined STM32F10X_XL) || (defined STM32F10X_HD_VL) + #ifdef DATA_IN_ExtSRAM + SystemInit_ExtMemCtl(); + #endif /* DATA_IN_ExtSRAM */ +#endif + + /* Configure the System clock frequency, HCLK, PCLK2 and PCLK1 prescalers */ + /* Configure the Flash Latency cycles and enable prefetch buffer */ + SetSysClock(); + +#ifdef VECT_TAB_SRAM + SCB->VTOR = SRAM_BASE | VECT_TAB_OFFSET; /* Vector Table Relocation in Internal SRAM. */ +#else + SCB->VTOR = FLASH_BASE | VECT_TAB_OFFSET; /* Vector Table Relocation in Internal FLASH. */ +#endif +} + +/** + * @brief Update SystemCoreClock variable according to Clock Register Values. + * The SystemCoreClock variable contains the core clock (HCLK), it can + * be used by the user application to setup the SysTick timer or configure + * other parameters. + * + * @note Each time the core clock (HCLK) changes, this function must be called + * to update SystemCoreClock variable value. Otherwise, any configuration + * based on this variable will be incorrect. + * + * @note - The system frequency computed by this function is not the real + * frequency in the chip. It is calculated based on the predefined + * constant and the selected clock source: + * + * - If SYSCLK source is HSI, SystemCoreClock will contain the HSI_VALUE(*) + * + * - If SYSCLK source is HSE, SystemCoreClock will contain the HSE_VALUE(**) + * + * - If SYSCLK source is PLL, SystemCoreClock will contain the HSE_VALUE(**) + * or HSI_VALUE(*) multiplied by the PLL factors. + * + * (*) HSI_VALUE is a constant defined in stm32f1xx.h file (default value + * 8 MHz) but the real value may vary depending on the variations + * in voltage and temperature. + * + * (**) HSE_VALUE is a constant defined in stm32f1xx.h file (default value + * 8 MHz or 25 MHz, depedning on the product used), user has to ensure + * that HSE_VALUE is same as the real frequency of the crystal used. + * Otherwise, this function may have wrong result. + * + * - The result of this function could be not correct when using fractional + * value for HSE crystal. + * @param None + * @retval None + */ +void SystemCoreClockUpdate (void) +{ + uint32_t tmp = 0, pllmull = 0, pllsource = 0; + +#ifdef STM32F10X_CL + uint32_t prediv1source = 0, prediv1factor = 0, prediv2factor = 0, pll2mull = 0; +#endif /* STM32F10X_CL */ + +#if defined (STM32F10X_LD_VL) || defined (STM32F10X_MD_VL) || (defined STM32F10X_HD_VL) + uint32_t prediv1factor = 0; +#endif /* STM32F10X_LD_VL or STM32F10X_MD_VL or STM32F10X_HD_VL */ + + /* Get SYSCLK source -------------------------------------------------------*/ + tmp = RCC->CFGR & RCC_CFGR_SWS; + + switch (tmp) + { + case 0x00: /* HSI used as system clock */ + SystemCoreClock = HSI_VALUE; + break; + case 0x04: /* HSE used as system clock */ + SystemCoreClock = HSE_VALUE; + break; + case 0x08: /* PLL used as system clock */ + + /* Get PLL clock source and multiplication factor ----------------------*/ + pllmull = RCC->CFGR & RCC_CFGR_PLLMULL; + pllsource = RCC->CFGR & RCC_CFGR_PLLSRC; + +#ifndef STM32F10X_CL + pllmull = ( pllmull >> 18) + 2; + + if (pllsource == 0x00) + { + /* HSI oscillator clock divided by 2 selected as PLL clock entry */ + SystemCoreClock = (HSI_VALUE >> 1) * pllmull; + } + else + { + #if defined (STM32F10X_LD_VL) || defined (STM32F10X_MD_VL) || (defined STM32F10X_HD_VL) + prediv1factor = (RCC->CFGR2 & RCC_CFGR2_PREDIV1) + 1; + /* HSE oscillator clock selected as PREDIV1 clock entry */ + SystemCoreClock = (HSE_VALUE / prediv1factor) * pllmull; + #else + /* HSE selected as PLL clock entry */ + if ((RCC->CFGR & RCC_CFGR_PLLXTPRE) != (uint32_t)RESET) + {/* HSE oscillator clock divided by 2 */ + SystemCoreClock = (HSE_VALUE >> 1) * pllmull; + } + else + { + SystemCoreClock = HSE_VALUE * pllmull; + } + #endif + } +#else + pllmull = pllmull >> 18; + + if (pllmull != 0x0D) + { + pllmull += 2; + } + else + { /* PLL multiplication factor = PLL input clock * 6.5 */ + pllmull = 13 / 2; + } + + if (pllsource == 0x00) + { + /* HSI oscillator clock divided by 2 selected as PLL clock entry */ + SystemCoreClock = (HSI_VALUE >> 1) * pllmull; + } + else + {/* PREDIV1 selected as PLL clock entry */ + + /* Get PREDIV1 clock source and division factor */ + prediv1source = RCC->CFGR2 & RCC_CFGR2_PREDIV1SRC; + prediv1factor = (RCC->CFGR2 & RCC_CFGR2_PREDIV1) + 1; + + if (prediv1source == 0) + { + /* HSE oscillator clock selected as PREDIV1 clock entry */ + SystemCoreClock = (HSE_VALUE / prediv1factor) * pllmull; + } + else + {/* PLL2 clock selected as PREDIV1 clock entry */ + + /* Get PREDIV2 division factor and PLL2 multiplication factor */ + prediv2factor = ((RCC->CFGR2 & RCC_CFGR2_PREDIV2) >> 4) + 1; + pll2mull = ((RCC->CFGR2 & RCC_CFGR2_PLL2MUL) >> 8 ) + 2; + SystemCoreClock = (((HSE_VALUE / prediv2factor) * pll2mull) / prediv1factor) * pllmull; + } + } +#endif /* STM32F10X_CL */ + break; + + default: + SystemCoreClock = HSI_VALUE; + break; + } + + /* Compute HCLK clock frequency ----------------*/ + /* Get HCLK prescaler */ + tmp = AHBPrescTable[((RCC->CFGR & RCC_CFGR_HPRE) >> 4)]; + /* HCLK clock frequency */ + SystemCoreClock >>= tmp; +} + +/** + * @brief Configures the System clock frequency, HCLK, PCLK2 and PCLK1 prescalers. + * @param None + * @retval None + */ +static void SetSysClock(void) +{ +#ifdef SYSCLK_FREQ_HSE + SetSysClockToHSE(); +#elif defined SYSCLK_FREQ_24MHz + SetSysClockTo24(); +#elif defined SYSCLK_FREQ_36MHz + SetSysClockTo36(); +#elif defined SYSCLK_FREQ_48MHz + SetSysClockTo48(); +#elif defined SYSCLK_FREQ_56MHz + SetSysClockTo56(); +#elif defined SYSCLK_FREQ_72MHz + SetSysClockTo72(); +#endif + + /* If none of the define above is enabled, the HSI is used as System clock + source (default after reset) */ +} + +/** + * @brief Setup the external memory controller. Called in startup_stm32f10x.s + * before jump to __main + * @param None + * @retval None + */ +#ifdef DATA_IN_ExtSRAM +/** + * @brief Setup the external memory controller. + * Called in startup_stm32f10x_xx.s/.c before jump to main. + * This function configures the external SRAM mounted on STM3210E-EVAL + * board (STM32 High density devices). This SRAM will be used as program + * data memory (including heap and stack). + * @param None + * @retval None + */ +void SystemInit_ExtMemCtl(void) +{ +/*!< FSMC Bank1 NOR/SRAM3 is used for the STM3210E-EVAL, if another Bank is + required, then adjust the Register Addresses */ + + /* Enable FSMC clock */ + RCC->AHBENR = 0x00000114; + + /* Enable GPIOD, GPIOE, GPIOF and GPIOG clocks */ + RCC->APB2ENR = 0x000001E0; + +/* --------------- SRAM Data lines, NOE and NWE configuration ---------------*/ +/*---------------- SRAM Address lines configuration -------------------------*/ +/*---------------- NOE and NWE configuration --------------------------------*/ +/*---------------- NE3 configuration ----------------------------------------*/ +/*---------------- NBL0, NBL1 configuration ---------------------------------*/ + + GPIOD->CRL = 0x44BB44BB; + GPIOD->CRH = 0xBBBBBBBB; + + GPIOE->CRL = 0xB44444BB; + GPIOE->CRH = 0xBBBBBBBB; + + GPIOF->CRL = 0x44BBBBBB; + GPIOF->CRH = 0xBBBB4444; + + GPIOG->CRL = 0x44BBBBBB; + GPIOG->CRH = 0x44444B44; + +/*---------------- FSMC Configuration ---------------------------------------*/ +/*---------------- Enable FSMC Bank1_SRAM Bank ------------------------------*/ + + FSMC_Bank1->BTCR[4] = 0x00001011; + FSMC_Bank1->BTCR[5] = 0x00000200; +} +#endif /* DATA_IN_ExtSRAM */ + +#ifdef SYSCLK_FREQ_HSE +/** + * @brief Selects HSE as System clock source and configure HCLK, PCLK2 + * and PCLK1 prescalers. + * @note This function should be used only after reset. + * @param None + * @retval None + */ +static void SetSysClockToHSE(void) +{ + __IO uint32_t StartUpCounter = 0, HSEStatus = 0; + + /* SYSCLK, HCLK, PCLK2 and PCLK1 configuration ---------------------------*/ + /* Enable HSE */ + RCC->CR |= ((uint32_t)RCC_CR_HSEON); + + /* Wait till HSE is ready and if Time out is reached exit */ + do + { + HSEStatus = RCC->CR & RCC_CR_HSERDY; + StartUpCounter++; + } while((HSEStatus == 0) && (StartUpCounter != HSE_STARTUP_TIMEOUT)); + + if ((RCC->CR & RCC_CR_HSERDY) != RESET) + { + HSEStatus = (uint32_t)0x01; + } + else + { + HSEStatus = (uint32_t)0x00; + } + + if (HSEStatus == (uint32_t)0x01) + { + +#if !defined STM32F10X_LD_VL && !defined STM32F10X_MD_VL && !defined STM32F10X_HD_VL + /* Enable Prefetch Buffer */ + FLASH->ACR |= FLASH_ACR_PRFTBE; + + /* Flash 0 wait state */ + FLASH->ACR &= (uint32_t)((uint32_t)~FLASH_ACR_LATENCY); + +#ifndef STM32F10X_CL + FLASH->ACR |= (uint32_t)FLASH_ACR_LATENCY_0; +#else + if (HSE_VALUE <= 24000000) + { + FLASH->ACR |= (uint32_t)FLASH_ACR_LATENCY_0; + } + else + { + FLASH->ACR |= (uint32_t)FLASH_ACR_LATENCY_1; + } +#endif /* STM32F10X_CL */ +#endif + + /* HCLK = SYSCLK */ + RCC->CFGR |= (uint32_t)RCC_CFGR_HPRE_DIV1; + + /* PCLK2 = HCLK */ + RCC->CFGR |= (uint32_t)RCC_CFGR_PPRE2_DIV1; + + /* PCLK1 = HCLK */ + RCC->CFGR |= (uint32_t)RCC_CFGR_PPRE1_DIV1; + + /* Select HSE as system clock source */ + RCC->CFGR &= (uint32_t)((uint32_t)~(RCC_CFGR_SW)); + RCC->CFGR |= (uint32_t)RCC_CFGR_SW_HSE; + + /* Wait till HSE is used as system clock source */ + while ((RCC->CFGR & (uint32_t)RCC_CFGR_SWS) != (uint32_t)0x04) + { + } + } + else + { /* If HSE fails to start-up, the application will have wrong clock + configuration. User can add here some code to deal with this error */ + } +} +#elif defined SYSCLK_FREQ_24MHz +/** + * @brief Sets System clock frequency to 24MHz and configure HCLK, PCLK2 + * and PCLK1 prescalers. + * @note This function should be used only after reset. + * @param None + * @retval None + */ +static void SetSysClockTo24(void) +{ + __IO uint32_t StartUpCounter = 0, HSEStatus = 0; + + /* SYSCLK, HCLK, PCLK2 and PCLK1 configuration ---------------------------*/ + /* Enable HSE */ + RCC->CR |= ((uint32_t)RCC_CR_HSEON); + + /* Wait till HSE is ready and if Time out is reached exit */ + do + { + HSEStatus = RCC->CR & RCC_CR_HSERDY; + StartUpCounter++; + } while((HSEStatus == 0) && (StartUpCounter != HSE_STARTUP_TIMEOUT)); + + if ((RCC->CR & RCC_CR_HSERDY) != RESET) + { + HSEStatus = (uint32_t)0x01; + } + else + { + HSEStatus = (uint32_t)0x00; + } + + if (HSEStatus == (uint32_t)0x01) + { +#if !defined STM32F10X_LD_VL && !defined STM32F10X_MD_VL && !defined STM32F10X_HD_VL + /* Enable Prefetch Buffer */ + FLASH->ACR |= FLASH_ACR_PRFTBE; + + /* Flash 0 wait state */ + FLASH->ACR &= (uint32_t)((uint32_t)~FLASH_ACR_LATENCY); + FLASH->ACR |= (uint32_t)FLASH_ACR_LATENCY_0; +#endif + + /* HCLK = SYSCLK */ + RCC->CFGR |= (uint32_t)RCC_CFGR_HPRE_DIV1; + + /* PCLK2 = HCLK */ + RCC->CFGR |= (uint32_t)RCC_CFGR_PPRE2_DIV1; + + /* PCLK1 = HCLK */ + RCC->CFGR |= (uint32_t)RCC_CFGR_PPRE1_DIV1; + +#ifdef STM32F10X_CL + /* Configure PLLs ------------------------------------------------------*/ + /* PLL configuration: PLLCLK = PREDIV1 * 6 = 24 MHz */ + RCC->CFGR &= (uint32_t)~(RCC_CFGR_PLLXTPRE | RCC_CFGR_PLLSRC | RCC_CFGR_PLLMULL); + RCC->CFGR |= (uint32_t)(RCC_CFGR_PLLXTPRE_PREDIV1 | RCC_CFGR_PLLSRC_PREDIV1 | + RCC_CFGR_PLLMULL6); + + /* PLL2 configuration: PLL2CLK = (HSE / 5) * 8 = 40 MHz */ + /* PREDIV1 configuration: PREDIV1CLK = PLL2 / 10 = 4 MHz */ + RCC->CFGR2 &= (uint32_t)~(RCC_CFGR2_PREDIV2 | RCC_CFGR2_PLL2MUL | + RCC_CFGR2_PREDIV1 | RCC_CFGR2_PREDIV1SRC); + RCC->CFGR2 |= (uint32_t)(RCC_CFGR2_PREDIV2_DIV5 | RCC_CFGR2_PLL2MUL8 | + RCC_CFGR2_PREDIV1SRC_PLL2 | RCC_CFGR2_PREDIV1_DIV10); + + /* Enable PLL2 */ + RCC->CR |= RCC_CR_PLL2ON; + /* Wait till PLL2 is ready */ + while((RCC->CR & RCC_CR_PLL2RDY) == 0) + { + } +#elif defined (STM32F10X_LD_VL) || defined (STM32F10X_MD_VL) || defined (STM32F10X_HD_VL) + /* PLL configuration: = (HSE / 2) * 6 = 24 MHz */ + RCC->CFGR &= (uint32_t)((uint32_t)~(RCC_CFGR_PLLSRC | RCC_CFGR_PLLXTPRE | RCC_CFGR_PLLMULL)); + RCC->CFGR |= (uint32_t)(RCC_CFGR_PLLSRC_PREDIV1 | RCC_CFGR_PLLXTPRE_PREDIV1_Div2 | RCC_CFGR_PLLMULL6); +#else + /* PLL configuration: = (HSE / 2) * 6 = 24 MHz */ + RCC->CFGR &= (uint32_t)((uint32_t)~(RCC_CFGR_PLLSRC | RCC_CFGR_PLLXTPRE | RCC_CFGR_PLLMULL)); + RCC->CFGR |= (uint32_t)(RCC_CFGR_PLLSRC_HSE | RCC_CFGR_PLLXTPRE_HSE_Div2 | RCC_CFGR_PLLMULL6); +#endif /* STM32F10X_CL */ + + /* Enable PLL */ + RCC->CR |= RCC_CR_PLLON; + + /* Wait till PLL is ready */ + while((RCC->CR & RCC_CR_PLLRDY) == 0) + { + } + + /* Select PLL as system clock source */ + RCC->CFGR &= (uint32_t)((uint32_t)~(RCC_CFGR_SW)); + RCC->CFGR |= (uint32_t)RCC_CFGR_SW_PLL; + + /* Wait till PLL is used as system clock source */ + while ((RCC->CFGR & (uint32_t)RCC_CFGR_SWS) != (uint32_t)0x08) + { + } + } + else + { /* If HSE fails to start-up, the application will have wrong clock + configuration. User can add here some code to deal with this error */ + } +} +#elif defined SYSCLK_FREQ_36MHz +/** + * @brief Sets System clock frequency to 36MHz and configure HCLK, PCLK2 + * and PCLK1 prescalers. + * @note This function should be used only after reset. + * @param None + * @retval None + */ +static void SetSysClockTo36(void) +{ + __IO uint32_t StartUpCounter = 0, HSEStatus = 0; + + /* SYSCLK, HCLK, PCLK2 and PCLK1 configuration ---------------------------*/ + /* Enable HSE */ + RCC->CR |= ((uint32_t)RCC_CR_HSEON); + + /* Wait till HSE is ready and if Time out is reached exit */ + do + { + HSEStatus = RCC->CR & RCC_CR_HSERDY; + StartUpCounter++; + } while((HSEStatus == 0) && (StartUpCounter != HSE_STARTUP_TIMEOUT)); + + if ((RCC->CR & RCC_CR_HSERDY) != RESET) + { + HSEStatus = (uint32_t)0x01; + } + else + { + HSEStatus = (uint32_t)0x00; + } + + if (HSEStatus == (uint32_t)0x01) + { + /* Enable Prefetch Buffer */ + FLASH->ACR |= FLASH_ACR_PRFTBE; + + /* Flash 1 wait state */ + FLASH->ACR &= (uint32_t)((uint32_t)~FLASH_ACR_LATENCY); + FLASH->ACR |= (uint32_t)FLASH_ACR_LATENCY_1; + + /* HCLK = SYSCLK */ + RCC->CFGR |= (uint32_t)RCC_CFGR_HPRE_DIV1; + + /* PCLK2 = HCLK */ + RCC->CFGR |= (uint32_t)RCC_CFGR_PPRE2_DIV1; + + /* PCLK1 = HCLK */ + RCC->CFGR |= (uint32_t)RCC_CFGR_PPRE1_DIV1; + +#ifdef STM32F10X_CL + /* Configure PLLs ------------------------------------------------------*/ + + /* PLL configuration: PLLCLK = PREDIV1 * 9 = 36 MHz */ + RCC->CFGR &= (uint32_t)~(RCC_CFGR_PLLXTPRE | RCC_CFGR_PLLSRC | RCC_CFGR_PLLMULL); + RCC->CFGR |= (uint32_t)(RCC_CFGR_PLLXTPRE_PREDIV1 | RCC_CFGR_PLLSRC_PREDIV1 | + RCC_CFGR_PLLMULL9); + + /*!< PLL2 configuration: PLL2CLK = (HSE / 5) * 8 = 40 MHz */ + /* PREDIV1 configuration: PREDIV1CLK = PLL2 / 10 = 4 MHz */ + + RCC->CFGR2 &= (uint32_t)~(RCC_CFGR2_PREDIV2 | RCC_CFGR2_PLL2MUL | + RCC_CFGR2_PREDIV1 | RCC_CFGR2_PREDIV1SRC); + RCC->CFGR2 |= (uint32_t)(RCC_CFGR2_PREDIV2_DIV5 | RCC_CFGR2_PLL2MUL8 | + RCC_CFGR2_PREDIV1SRC_PLL2 | RCC_CFGR2_PREDIV1_DIV10); + + /* Enable PLL2 */ + RCC->CR |= RCC_CR_PLL2ON; + /* Wait till PLL2 is ready */ + while((RCC->CR & RCC_CR_PLL2RDY) == 0) + { + } + +#else + /* PLL configuration: PLLCLK = (HSE / 2) * 9 = 36 MHz */ + RCC->CFGR &= (uint32_t)((uint32_t)~(RCC_CFGR_PLLSRC | RCC_CFGR_PLLXTPRE | RCC_CFGR_PLLMULL)); + RCC->CFGR |= (uint32_t)(RCC_CFGR_PLLSRC_HSE | RCC_CFGR_PLLXTPRE_HSE_Div2 | RCC_CFGR_PLLMULL9); +#endif /* STM32F10X_CL */ + + /* Enable PLL */ + RCC->CR |= RCC_CR_PLLON; + + /* Wait till PLL is ready */ + while((RCC->CR & RCC_CR_PLLRDY) == 0) + { + } + + /* Select PLL as system clock source */ + RCC->CFGR &= (uint32_t)((uint32_t)~(RCC_CFGR_SW)); + RCC->CFGR |= (uint32_t)RCC_CFGR_SW_PLL; + + /* Wait till PLL is used as system clock source */ + while ((RCC->CFGR & (uint32_t)RCC_CFGR_SWS) != (uint32_t)0x08) + { + } + } + else + { /* If HSE fails to start-up, the application will have wrong clock + configuration. User can add here some code to deal with this error */ + } +} +#elif defined SYSCLK_FREQ_48MHz +/** + * @brief Sets System clock frequency to 48MHz and configure HCLK, PCLK2 + * and PCLK1 prescalers. + * @note This function should be used only after reset. + * @param None + * @retval None + */ +static void SetSysClockTo48(void) +{ + __IO uint32_t StartUpCounter = 0, HSEStatus = 0; + + /* SYSCLK, HCLK, PCLK2 and PCLK1 configuration ---------------------------*/ + /* Enable HSE */ + RCC->CR |= ((uint32_t)RCC_CR_HSEON); + + /* Wait till HSE is ready and if Time out is reached exit */ + do + { + HSEStatus = RCC->CR & RCC_CR_HSERDY; + StartUpCounter++; + } while((HSEStatus == 0) && (StartUpCounter != HSE_STARTUP_TIMEOUT)); + + if ((RCC->CR & RCC_CR_HSERDY) != RESET) + { + HSEStatus = (uint32_t)0x01; + } + else + { + HSEStatus = (uint32_t)0x00; + } + + if (HSEStatus == (uint32_t)0x01) + { + /* Enable Prefetch Buffer */ + FLASH->ACR |= FLASH_ACR_PRFTBE; + + /* Flash 1 wait state */ + FLASH->ACR &= (uint32_t)((uint32_t)~FLASH_ACR_LATENCY); + FLASH->ACR |= (uint32_t)FLASH_ACR_LATENCY_1; + + /* HCLK = SYSCLK */ + RCC->CFGR |= (uint32_t)RCC_CFGR_HPRE_DIV1; + + /* PCLK2 = HCLK */ + RCC->CFGR |= (uint32_t)RCC_CFGR_PPRE2_DIV1; + + /* PCLK1 = HCLK */ + RCC->CFGR |= (uint32_t)RCC_CFGR_PPRE1_DIV2; + +#ifdef STM32F10X_CL + /* Configure PLLs ------------------------------------------------------*/ + /* PLL2 configuration: PLL2CLK = (HSE / 5) * 8 = 40 MHz */ + /* PREDIV1 configuration: PREDIV1CLK = PLL2 / 5 = 8 MHz */ + + RCC->CFGR2 &= (uint32_t)~(RCC_CFGR2_PREDIV2 | RCC_CFGR2_PLL2MUL | + RCC_CFGR2_PREDIV1 | RCC_CFGR2_PREDIV1SRC); + RCC->CFGR2 |= (uint32_t)(RCC_CFGR2_PREDIV2_DIV5 | RCC_CFGR2_PLL2MUL8 | + RCC_CFGR2_PREDIV1SRC_PLL2 | RCC_CFGR2_PREDIV1_DIV5); + + /* Enable PLL2 */ + RCC->CR |= RCC_CR_PLL2ON; + /* Wait till PLL2 is ready */ + while((RCC->CR & RCC_CR_PLL2RDY) == 0) + { + } + + + /* PLL configuration: PLLCLK = PREDIV1 * 6 = 48 MHz */ + RCC->CFGR &= (uint32_t)~(RCC_CFGR_PLLXTPRE | RCC_CFGR_PLLSRC | RCC_CFGR_PLLMULL); + RCC->CFGR |= (uint32_t)(RCC_CFGR_PLLXTPRE_PREDIV1 | RCC_CFGR_PLLSRC_PREDIV1 | + RCC_CFGR_PLLMULL6); +#else + /* PLL configuration: PLLCLK = HSE * 6 = 48 MHz */ + RCC->CFGR &= (uint32_t)((uint32_t)~(RCC_CFGR_PLLSRC | RCC_CFGR_PLLXTPRE | RCC_CFGR_PLLMULL)); + RCC->CFGR |= (uint32_t)(RCC_CFGR_PLLSRC_HSE | RCC_CFGR_PLLMULL6); +#endif /* STM32F10X_CL */ + + /* Enable PLL */ + RCC->CR |= RCC_CR_PLLON; + + /* Wait till PLL is ready */ + while((RCC->CR & RCC_CR_PLLRDY) == 0) + { + } + + /* Select PLL as system clock source */ + RCC->CFGR &= (uint32_t)((uint32_t)~(RCC_CFGR_SW)); + RCC->CFGR |= (uint32_t)RCC_CFGR_SW_PLL; + + /* Wait till PLL is used as system clock source */ + while ((RCC->CFGR & (uint32_t)RCC_CFGR_SWS) != (uint32_t)0x08) + { + } + } + else + { /* If HSE fails to start-up, the application will have wrong clock + configuration. User can add here some code to deal with this error */ + } +} + +#elif defined SYSCLK_FREQ_56MHz +/** + * @brief Sets System clock frequency to 56MHz and configure HCLK, PCLK2 + * and PCLK1 prescalers. + * @note This function should be used only after reset. + * @param None + * @retval None + */ +static void SetSysClockTo56(void) +{ + __IO uint32_t StartUpCounter = 0, HSEStatus = 0; + + /* SYSCLK, HCLK, PCLK2 and PCLK1 configuration ---------------------------*/ + /* Enable HSE */ + RCC->CR |= ((uint32_t)RCC_CR_HSEON); + + /* Wait till HSE is ready and if Time out is reached exit */ + do + { + HSEStatus = RCC->CR & RCC_CR_HSERDY; + StartUpCounter++; + } while((HSEStatus == 0) && (StartUpCounter != HSE_STARTUP_TIMEOUT)); + + if ((RCC->CR & RCC_CR_HSERDY) != RESET) + { + HSEStatus = (uint32_t)0x01; + } + else + { + HSEStatus = (uint32_t)0x00; + } + + if (HSEStatus == (uint32_t)0x01) + { + /* Enable Prefetch Buffer */ + FLASH->ACR |= FLASH_ACR_PRFTBE; + + /* Flash 2 wait state */ + FLASH->ACR &= (uint32_t)((uint32_t)~FLASH_ACR_LATENCY); + FLASH->ACR |= (uint32_t)FLASH_ACR_LATENCY_2; + + /* HCLK = SYSCLK */ + RCC->CFGR |= (uint32_t)RCC_CFGR_HPRE_DIV1; + + /* PCLK2 = HCLK */ + RCC->CFGR |= (uint32_t)RCC_CFGR_PPRE2_DIV1; + + /* PCLK1 = HCLK */ + RCC->CFGR |= (uint32_t)RCC_CFGR_PPRE1_DIV2; + +#ifdef STM32F10X_CL + /* Configure PLLs ------------------------------------------------------*/ + /* PLL2 configuration: PLL2CLK = (HSE / 5) * 8 = 40 MHz */ + /* PREDIV1 configuration: PREDIV1CLK = PLL2 / 5 = 8 MHz */ + + RCC->CFGR2 &= (uint32_t)~(RCC_CFGR2_PREDIV2 | RCC_CFGR2_PLL2MUL | + RCC_CFGR2_PREDIV1 | RCC_CFGR2_PREDIV1SRC); + RCC->CFGR2 |= (uint32_t)(RCC_CFGR2_PREDIV2_DIV5 | RCC_CFGR2_PLL2MUL8 | + RCC_CFGR2_PREDIV1SRC_PLL2 | RCC_CFGR2_PREDIV1_DIV5); + + /* Enable PLL2 */ + RCC->CR |= RCC_CR_PLL2ON; + /* Wait till PLL2 is ready */ + while((RCC->CR & RCC_CR_PLL2RDY) == 0) + { + } + + + /* PLL configuration: PLLCLK = PREDIV1 * 7 = 56 MHz */ + RCC->CFGR &= (uint32_t)~(RCC_CFGR_PLLXTPRE | RCC_CFGR_PLLSRC | RCC_CFGR_PLLMULL); + RCC->CFGR |= (uint32_t)(RCC_CFGR_PLLXTPRE_PREDIV1 | RCC_CFGR_PLLSRC_PREDIV1 | + RCC_CFGR_PLLMULL7); +#else + /* PLL configuration: PLLCLK = HSE * 7 = 56 MHz */ + RCC->CFGR &= (uint32_t)((uint32_t)~(RCC_CFGR_PLLSRC | RCC_CFGR_PLLXTPRE | RCC_CFGR_PLLMULL)); + RCC->CFGR |= (uint32_t)(RCC_CFGR_PLLSRC_HSE | RCC_CFGR_PLLMULL7); + +#endif /* STM32F10X_CL */ + + /* Enable PLL */ + RCC->CR |= RCC_CR_PLLON; + + /* Wait till PLL is ready */ + while((RCC->CR & RCC_CR_PLLRDY) == 0) + { + } + + /* Select PLL as system clock source */ + RCC->CFGR &= (uint32_t)((uint32_t)~(RCC_CFGR_SW)); + RCC->CFGR |= (uint32_t)RCC_CFGR_SW_PLL; + + /* Wait till PLL is used as system clock source */ + while ((RCC->CFGR & (uint32_t)RCC_CFGR_SWS) != (uint32_t)0x08) + { + } + } + else + { /* If HSE fails to start-up, the application will have wrong clock + configuration. User can add here some code to deal with this error */ + } +} + +#elif defined SYSCLK_FREQ_72MHz +/** + * @brief Sets System clock frequency to 72MHz and configure HCLK, PCLK2 + * and PCLK1 prescalers. + * @note This function should be used only after reset. + * @param None + * @retval None + */ +static void SetSysClockTo72(void) +{ + __IO uint32_t StartUpCounter = 0, HSEStatus = 0; + + /* SYSCLK, HCLK, PCLK2 and PCLK1 configuration ---------------------------*/ + /* Enable HSE */ + RCC->CR |= ((uint32_t)RCC_CR_HSEON); + + /* Wait till HSE is ready and if Time out is reached exit */ + do + { + HSEStatus = RCC->CR & RCC_CR_HSERDY; + StartUpCounter++; + } while((HSEStatus == 0) && (StartUpCounter != HSE_STARTUP_TIMEOUT)); + + if ((RCC->CR & RCC_CR_HSERDY) != RESET) + { + HSEStatus = (uint32_t)0x01; + } + else + { + HSEStatus = (uint32_t)0x00; + } + + if (HSEStatus == (uint32_t)0x01) + { + /* Enable Prefetch Buffer */ + FLASH->ACR |= FLASH_ACR_PRFTBE; + + /* Flash 2 wait state */ + FLASH->ACR &= (uint32_t)((uint32_t)~FLASH_ACR_LATENCY); + FLASH->ACR |= (uint32_t)FLASH_ACR_LATENCY_2; + + + /* HCLK = SYSCLK */ + RCC->CFGR |= (uint32_t)RCC_CFGR_HPRE_DIV1; + + /* PCLK2 = HCLK */ + RCC->CFGR |= (uint32_t)RCC_CFGR_PPRE2_DIV1; + + /* PCLK1 = HCLK */ + RCC->CFGR |= (uint32_t)RCC_CFGR_PPRE1_DIV2; + +#ifdef STM32F10X_CL + /* Configure PLLs ------------------------------------------------------*/ + /* PLL2 configuration: PLL2CLK = (HSE / 5) * 8 = 40 MHz */ + /* PREDIV1 configuration: PREDIV1CLK = PLL2 / 5 = 8 MHz */ + + RCC->CFGR2 &= (uint32_t)~(RCC_CFGR2_PREDIV2 | RCC_CFGR2_PLL2MUL | + RCC_CFGR2_PREDIV1 | RCC_CFGR2_PREDIV1SRC); + RCC->CFGR2 |= (uint32_t)(RCC_CFGR2_PREDIV2_DIV5 | RCC_CFGR2_PLL2MUL8 | + RCC_CFGR2_PREDIV1SRC_PLL2 | RCC_CFGR2_PREDIV1_DIV5); + + /* Enable PLL2 */ + RCC->CR |= RCC_CR_PLL2ON; + /* Wait till PLL2 is ready */ + while((RCC->CR & RCC_CR_PLL2RDY) == 0) + { + } + + + /* PLL configuration: PLLCLK = PREDIV1 * 9 = 72 MHz */ + RCC->CFGR &= (uint32_t)~(RCC_CFGR_PLLXTPRE | RCC_CFGR_PLLSRC | RCC_CFGR_PLLMULL); + RCC->CFGR |= (uint32_t)(RCC_CFGR_PLLXTPRE_PREDIV1 | RCC_CFGR_PLLSRC_PREDIV1 | + RCC_CFGR_PLLMULL9); +#else + /* PLL configuration: PLLCLK = HSE * 9 = 72 MHz */ + RCC->CFGR &= (uint32_t)((uint32_t)~(RCC_CFGR_PLLSRC | RCC_CFGR_PLLXTPRE | + RCC_CFGR_PLLMULL)); + RCC->CFGR |= (uint32_t)(RCC_CFGR_PLLSRC_HSE | RCC_CFGR_PLLMULL9); +#endif /* STM32F10X_CL */ + + /* Enable PLL */ + RCC->CR |= RCC_CR_PLLON; + + /* Wait till PLL is ready */ + while((RCC->CR & RCC_CR_PLLRDY) == 0) + { + } + + /* Select PLL as system clock source */ + RCC->CFGR &= (uint32_t)((uint32_t)~(RCC_CFGR_SW)); + RCC->CFGR |= (uint32_t)RCC_CFGR_SW_PLL; + + /* Wait till PLL is used as system clock source */ + while ((RCC->CFGR & (uint32_t)RCC_CFGR_SWS) != (uint32_t)0x08) + { + } + } + else + { /* If HSE fails to start-up, the application will have wrong clock + configuration. User can add here some code to deal with this error */ + } +} +#endif + +/** + * @} + */ + +/** + * @} + */ + +/** + * @} + */ +/******************* (C) COPYRIGHT 2011 STMicroelectronics *****END OF FILE****/ -- cgit v1.2.3