From afbb4cc73c44b6321cae39dbe46b97155805097d Mon Sep 17 00:00:00 2001 From: Trygve Laugstøl Date: Sun, 13 Dec 2015 21:03:11 +0100 Subject: wip --- .../RTC/Calendar/readme.txt | 150 +++++++++++++++++++++ 1 file changed, 150 insertions(+) create mode 100644 tmp/STM32F10x_StdPeriph_Lib_V3.5.0/Project/STM32F10x_StdPeriph_Examples/RTC/Calendar/readme.txt (limited to 'tmp/STM32F10x_StdPeriph_Lib_V3.5.0/Project/STM32F10x_StdPeriph_Examples/RTC/Calendar/readme.txt') diff --git a/tmp/STM32F10x_StdPeriph_Lib_V3.5.0/Project/STM32F10x_StdPeriph_Examples/RTC/Calendar/readme.txt b/tmp/STM32F10x_StdPeriph_Lib_V3.5.0/Project/STM32F10x_StdPeriph_Examples/RTC/Calendar/readme.txt new file mode 100644 index 0000000..e63a786 --- /dev/null +++ b/tmp/STM32F10x_StdPeriph_Lib_V3.5.0/Project/STM32F10x_StdPeriph_Examples/RTC/Calendar/readme.txt @@ -0,0 +1,150 @@ +/** + @page RTC_Calendar RTC Calendar example + + @verbatim + ******************** (C) COPYRIGHT 2011 STMicroelectronics ******************* + * @file RTC/Calendar/readme.txt + * @author MCD Application Team + * @version V3.5.0 + * @date 08-April-2011 + * @brief Description of the RTC Calendar example. + ****************************************************************************** + * THE PRESENT FIRMWARE WHICH IS FOR GUIDANCE ONLY AIMS AT PROVIDING CUSTOMERS + * WITH CODING INFORMATION REGARDING THEIR PRODUCTS IN ORDER FOR THEM TO SAVE + * TIME. AS A RESULT, STMICROELECTRONICS SHALL NOT BE HELD LIABLE FOR ANY + * DIRECT, INDIRECT OR CONSEQUENTIAL DAMAGES WITH RESPECT TO ANY CLAIMS ARISING + * FROM THE CONTENT OF SUCH FIRMWARE AND/OR THE USE MADE BY CUSTOMERS OF THE + * CODING INFORMATION CONTAINED HEREIN IN CONNECTION WITH THEIR PRODUCTS. + ****************************************************************************** + @endverbatim + +@par Example Description + +This example demonstrates and explains how to use the RTC peripheral. +As an application example, it demonstrates how to setup the RTC peripheral, in terms +of prescaler and interrupts, to be used to keep time and to generate Second interrupt. + +The Low Speed External (LSE) clock is used as RTC clock source. +The RTC clock can be output on the Tamper pin (PC.13). To enable this functionality, +uncomment the corresponding line: #define RTCClockOutput_Enable in the main.c file. + +The RTC is in the backup (BKP) domain, still powered by VBAT when VDD is switched off, +so the RTC configuration is not lost if a battery is connected to the VBAT pin. +A key value is written in backup data register1 (BKP_DR1) to indicate if the RTC +is already configured. + +The program behaves as follows: + +1. After startup the program checks the backup data register1 value: + - register1 value not correct: (BKP_DR1 value is not correct or has not yet + been programmed when the program is executed for the first time) the RTC is + configured and the user is asked to set the time (entered on HyperTerminal). + + - register1 value correct: this means that the RTC is configured and the time + is displayed on HyperTerminal. + +2. When an External Reset occurs the BKP domain is not reset and the RTC configuration + is not lost. + +3. When power on reset occurs: + - If a battery is connected to the VBAT pin: the BKP domain is not reset and + the RTC configuration is not lost. + + - If no battery is connected to the VBAT pin: the BKP domain is reset and the + RTC configuration is lost. + +In the RTC interrupt service routine, the LED1 toggles every 1 s. +The C library printf function is retargeted to the USART, that is, the printf +message is output to the HyperTerminal using USART1 or USART2 depending on the +EVAL board you are using. + + +@par Directory contents + + - RTC/Calendar/stm32f10x_conf.h Library Configuration file + - RTC/Calendar/stm32f10x_it.c Interrupt handlers + - RTC/Calendar/stm32f10x_it.h Header for stm32f10x_it.c + - RTC/Calendar/main.c Main program + - RTC/Calendar/system_stm32f10x.c STM32F10x system source file + +@par Hardware and Software environment + + - This example runs on STM32F10x Connectivity line, High-Density, High-Density + Value line, Medium-Density, XL-Density, Medium-Density Value line, Low-Density + and Low-Density Value line Devices. + + - This example has been tested with STMicroelectronics STM32100E-EVAL (High-Density + Value line), STM32100B-EVAL (Medium-Density Value line), STM3210C-EVAL (Connectivity line), + STM3210E-EVAL (High-Density and XL-Density) and STM3210B-EVAL (Medium-Density) + evaluation boards and can be easily tailored to any other supported device + and development board. + To select the STMicroelectronics evaluation board used to run the example, + uncomment the corresponding line in stm32_eval.h file (under Utilities\STM32_EVAL) + + - STM32100E-EVAL Set-up + - Use LED1 connected to PF.06. + - Connect a null-modem female/female RS232 cable between the DB9 connector + CN10(when USART1 is used) and PC serial port. + - Make sure that jumper JP1 is in position 1-2 to connect the 3V battery to VBAT pin + + - STM32100B-EVAL Set-up + - Use LED1 connected to PC.06. + - Connect a null-modem female/female RS232 cable between the DB9 connector + CN10(when USART1 is used) and PC serial port. + - Make sure that jumper JP9 is in position 1-2 to connect the 3V battery to VBAT pin + + - STM3210C-EVAL Set-up + - Use LED1 connected to PD.07. + - Connect a null-modem female/female RS232 cable between the DB9 connector + CN6 (USART2) and PC serial port . + @note Make sure that jumpers JP19 and JP18 are open. + - Make sure that jumper JP24 is in position 1-2 to connect the 3V battery to VBAT pin + + - STM3210E-EVAL Set-up + - Use LED1 connected to PF.06. + - Connect a null-modem female/female RS232 cable between the DB9 connector + CN12(when USART1 is used) and PC serial port. + - Make sure that jumper JP1 is in position 1-2 to connect the 3V battery to VBAT pin + + - STM3210B-EVAL Set-up + - Use LED1 connected to PC.06. + - Connect a null-modem female/female RS232 cable between the DB9 connector + CN6(when USART1 is used) and PC serial port. + - Make sure that jumper JP11 is in position 1-2 to connect the 3V battery to VBAT pin + + - Hyperterminal configuration: + - Word Length = 8 Bits + - One Stop Bit + - No parity + - BaudRate = 115200 baud + - flow control: None + + +@par How to use it ? + +In order to make the program work, you must do the following : + - Copy all source files from this example folder to the template folder under + Project\STM32F10x_StdPeriph_Template + - Open your preferred toolchain + - Rebuild all files and load your image into target memory + - Run the example + +@note + - Low-density Value line devices are STM32F100xx microcontrollers where the + Flash memory density ranges between 16 and 32 Kbytes. + - Low-density devices are STM32F101xx, STM32F102xx and STM32F103xx + microcontrollers where the Flash memory density ranges between 16 and 32 Kbytes. + - Medium-density Value line devices are STM32F100xx microcontrollers where + the Flash memory density ranges between 64 and 128 Kbytes. + - Medium-density devices are STM32F101xx, STM32F102xx and STM32F103xx + microcontrollers where the Flash memory density ranges between 64 and 128 Kbytes. + - High-density Value line devices are STM32F100xx microcontrollers where + the Flash memory density ranges between 256 and 512 Kbytes. + - High-density devices are STM32F101xx and STM32F103xx microcontrollers where + the Flash memory density ranges between 256 and 512 Kbytes. + - XL-density devices are STM32F101xx and STM32F103xx microcontrollers where + the Flash memory density ranges between 512 and 1024 Kbytes. + - Connectivity line devices are STM32F105xx and STM32F107xx microcontrollers. + + *

© COPYRIGHT 2011 STMicroelectronics

+ */ -- cgit v1.2.3