/**
  ******************************************************************************
  * @file    usb_conf.h
  * @author  MCD Application Team
  * @version V4.0.0
  * @date    21-January-2013
  * @brief   Device Firmware Upgrade (DFU) configuration file
  ******************************************************************************
  * @attention
  *
  * <h2><center>&copy; COPYRIGHT 2013 STMicroelectronics</center></h2>
  *
  * Licensed under MCD-ST Liberty SW License Agreement V2, (the "License");
  * You may not use this file except in compliance with the License.
  * You may obtain a copy of the License at:
  *
  *        http://www.st.com/software_license_agreement_liberty_v2
  *
  * Unless required by applicable law or agreed to in writing, software 
  * distributed under the License is distributed on an "AS IS" BASIS, 
  * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
  * See the License for the specific language governing permissions and
  * limitations under the License.
  *
  ******************************************************************************
  */


/* Define to prevent recursive inclusion -------------------------------------*/
#ifndef __USB_CONF_H
#define __USB_CONF_H

/* Includes ------------------------------------------------------------------*/
/* Exported types ------------------------------------------------------------*/
/* Exported constants --------------------------------------------------------*/

/* These timings will be returned to the host when it checks the device
   status during a write or erase operation to know how much time the host
   should wait before issuing the next get status request. 
   These defines are set in usb_conf.h file.
   The values of this table should be extracted from relative memories 
   datasheet (Typical or Maximum timming value for Sector Erase and for 
   1024 bytes Write). All timings are expressed in millisecond unit (ms).
   Note that "Sector" refers here to the memory unit used for Erase/Write 
   operations. It could be a sector, a page, a block, a word ...
   If the erase operation is not supported, it is advised to set the erase
   timing to 1 (which means 1ms: one USB frame). */
#define SPI_FLASH_SECTOR_ERASE_TIME     3000
#define SPI_FLASH_SECTOR_WRITE_TIME     20

#if defined(STM32L1XX_MD) || defined(STM32L1XX_HD)|| defined(STM32L1XX_MD_PLUS)    
 #define INTERN_FLASH_SECTOR_ERASE_TIME 100
 #define INTERN_FLASH_SECTOR_WRITE_TIME 104   
#else
 #define INTERN_FLASH_SECTOR_ERASE_TIME 50
 #define INTERN_FLASH_SECTOR_WRITE_TIME 50
#endif /* STM32L1XX_XD */   

#define M29W128F_SECTOR_ERASE_TIME      1000
#define M29W128F_SECTOR_WRITE_TIME      25 

#define M29W128G_SECTOR_ERASE_TIME      1000
#define M29W128G_SECTOR_WRITE_TIME      25

#define S29GL128_SECTOR_ERASE_TIME      1000
#define S29GL128_SECTOR_WRITE_TIME      45

/* Exported macro ------------------------------------------------------------*/
/* Exported functions ------------------------------------------------------- */
/* External variables --------------------------------------------------------*/
/*-------------------------------------------------------------*/
/* EP_NUM */
/* defines how many endpoints are used by the device */
/*-------------------------------------------------------------*/
#define EP_NUM                          (1)

/*-------------------------------------------------------------*/
/* --------------   Buffer Description Table  -----------------*/
/*-------------------------------------------------------------*/
/* buffer table base address */
/* buffer table base address */
#define BTABLE_ADDRESS      (0x00)

/* EP0 */
/* rx/tx buffer base address */
#define ENDP0_RXADDR        (0x10)
#define ENDP0_TXADDR        (0x50)


/*-------------------------------------------------------------*/
/* -------------------   ISTR events  -------------------------*/
/*-------------------------------------------------------------*/
/* IMR_MSK */
/* mask defining which events has to be handled */
/* by the device application software */
#define IMR_MSK (CNTR_CTRM  | CNTR_WKUPM | CNTR_SUSPM | CNTR_ERRM  | CNTR_SOFM \
                 | CNTR_ESOFM | CNTR_RESETM )

/* CTR service routines */
/* associated to defined endpoints */
#define  EP1_IN_Callback   NOP_Process
#define  EP2_IN_Callback   NOP_Process
#define  EP3_IN_Callback   NOP_Process
#define  EP4_IN_Callback   NOP_Process
#define  EP5_IN_Callback   NOP_Process
#define  EP6_IN_Callback   NOP_Process
#define  EP7_IN_Callback   NOP_Process


#define  EP1_OUT_Callback   NOP_Process
#define  EP2_OUT_Callback   NOP_Process
#define  EP3_OUT_Callback   NOP_Process
#define  EP4_OUT_Callback   NOP_Process
#define  EP5_OUT_Callback   NOP_Process
#define  EP6_OUT_Callback   NOP_Process
#define  EP7_OUT_Callback   NOP_Process

#endif /*__USB_CONF_H*/

/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/