/**
  @page TIM_OCInactive TIM OC Inactive example
  
  @verbatim
  ******************** (C) COPYRIGHT 2011 STMicroelectronics *******************
  * @file    TIM/OCInactive/readme.txt 
  * @author  MCD Application Team
  * @version V3.5.0
  * @date    08-April-2011
  * @brief   Description of the TIM OC Inactive example.
  ******************************************************************************
  * THE PRESENT FIRMWARE WHICH IS FOR GUIDANCE ONLY AIMS AT PROVIDING CUSTOMERS
  * WITH CODING INFORMATION REGARDING THEIR PRODUCTS IN ORDER FOR THEM TO SAVE
  * TIME. AS A RESULT, STMICROELECTRONICS SHALL NOT BE HELD LIABLE FOR ANY
  * DIRECT, INDIRECT OR CONSEQUENTIAL DAMAGES WITH RESPECT TO ANY CLAIMS ARISING
  * FROM THE CONTENT OF SUCH FIRMWARE AND/OR THE USE MADE BY CUSTOMERS OF THE
  * CODING INFORMATION CONTAINED HEREIN IN CONNECTION WITH THEIR PRODUCTS.
  ******************************************************************************
   @endverbatim

@par Example Description 

This example shows how to configure the TIM peripheral in Output Compare Inactive 
mode with the corresponding Interrupt requests for each channel.

The TIM2CLK frequency is set to SystemCoreClock / 2 (Hz), and the objective is
to get TIM2 counter clock at 1 KHz so the Prescaler is computed as following:
   - Prescaler = (TIM2CLK / TIM2 counter clock) - 1
SystemCoreClock is set to 72 MHz for Low-density, Medium-density, High-density
and Connectivity line devices and to 24 MHz for Value line devices.

The TIM2 CCR1 register value is equal to 1000:
TIM2_CC1 delay = CCR1_Val/TIM2 counter clock  = 1000 ms
so the PC.06  is reset after a delay equal to 1000 ms.

The TIM2 CCR2 register value is equal to 500:
TIM2_CC2 delay = CCR2_Val/TIM2 counter clock = 500 ms
so the PC.07  is reset after a delay equal to 500 ms.

The TIM2 CCR3 register value is equal to 250:
TIM2_CC3 delay = CCR3_Val/TIM2 counter clock = 250 ms
so the PC.08  is reset after a delay equal to 250 ms.

The TIM2 CCR4 register value is equal to 125:
TIM2_CC4 delay = CCR4_Val/TIM2 counter clock = 125 ms
so the PC.09  is reset after a delay equal to 125 ms.

While the counter is lower than the Output compare registers values, which 
determines the Output delay, the PC.06, PC.07, PC.08 and PC.09 pin are turned on. 

When the counter value reaches the Output compare registers values, the Output 
Compare interrupts are generated and, in the handler routine, these pins are turned off.

@par Directory contents 

  - TIM/OCInactive/stm32f10x_conf.h    Library Configuration file
  - TIM/OCInactive/stm32f10x_it.c      Interrupt handlers
  - TIM/OCInactive/stm32f10x_it.h      Interrupt handlers header file
  - TIM/OCInactive/main.c              Main program
  - TIM/OCInactive/system_stm32f10x.c  STM32F10x system source file

@par Hardware and Software environment 

  - This example runs on STM32F10x Connectivity line, High-Density, High-Density 
    Value line, Medium-Density, XL-Density, Medium-Density Value line, Low-Density 
    and Low-Density Value line Devices.
  
  - This example has been tested with STMicroelectronics STM32100E-EVAL (High-Density
    Value line), STM32100B-EVAL (Medium-Density Value line), STM3210C-EVAL (Connectivity line), 
    STM3210E-EVAL (High-Density and XL-Density) and STM3210B-EVAL (Medium-Density) 
    evaluation boards and can be easily tailored to any other supported device 
    and development board.

  - STM32100B-EVAL, STM3210E-EVAL, STM32100E-EVAL STM3210B-EVAL and STM3210C-EVAL Set-up 
    - Connect the following pins to an oscilloscope to monitor the different 
      waveforms:
        - PC.06
        - PC.07
        - PC.08 
        - PC.09
  
@par How to use it ? 

In order to make the program work, you must do the following :
 - Copy all source files from this example folder to the template folder under
   Project\STM32F10x_StdPeriph_Template
 - Open your preferred toolchain 
 - Rebuild all files and load your image into target memory
 - Run the example

@note
 - Low-density Value line devices are STM32F100xx microcontrollers where the 
   Flash memory density ranges between 16 and 32 Kbytes.
 - Low-density devices are STM32F101xx, STM32F102xx and STM32F103xx 
   microcontrollers where the Flash memory density ranges between 16 and 32 Kbytes.
 - Medium-density Value line devices are STM32F100xx microcontrollers where
   the Flash memory density ranges between 64 and 128 Kbytes.  
 - Medium-density devices are STM32F101xx, STM32F102xx and STM32F103xx 
   microcontrollers where the Flash memory density ranges between 64 and 128 Kbytes.
 - High-density Value line devices are STM32F100xx microcontrollers where
   the Flash memory density ranges between 256 and 512 Kbytes.
 - High-density devices are STM32F101xx and STM32F103xx microcontrollers where
   the Flash memory density ranges between 256 and 512 Kbytes.
 - XL-density devices are STM32F101xx and STM32F103xx microcontrollers where
   the Flash memory density ranges between 512 and 1024 Kbytes.
 - Connectivity line devices are STM32F105xx and STM32F107xx microcontrollers.
   
 * <h3><center>&copy; COPYRIGHT 2011 STMicroelectronics</center></h3>
 */