From a819d3cbddbb5294b98b2fd6590f9fff13491d85 Mon Sep 17 00:00:00 2001 From: Trygve Laugstøl Date: Sat, 27 May 2017 10:55:23 +0200 Subject: o Moving generated code to under bsp/. Renaming to match PCB. --- .../Src/stm32f1xx_hal_cortex.c | 494 +++++++++++++++++++++ 1 file changed, 494 insertions(+) create mode 100644 bsp/radio-controller-1/Drivers/STM32F1xx_HAL_Driver/Src/stm32f1xx_hal_cortex.c (limited to 'bsp/radio-controller-1/Drivers/STM32F1xx_HAL_Driver/Src/stm32f1xx_hal_cortex.c') diff --git a/bsp/radio-controller-1/Drivers/STM32F1xx_HAL_Driver/Src/stm32f1xx_hal_cortex.c b/bsp/radio-controller-1/Drivers/STM32F1xx_HAL_Driver/Src/stm32f1xx_hal_cortex.c new file mode 100644 index 0000000..836503c --- /dev/null +++ b/bsp/radio-controller-1/Drivers/STM32F1xx_HAL_Driver/Src/stm32f1xx_hal_cortex.c @@ -0,0 +1,494 @@ +/** + ****************************************************************************** + * @file stm32f1xx_hal_cortex.c + * @author MCD Application Team + * @version V1.0.4 + * @date 29-April-2016 + * @brief CORTEX HAL module driver. + * + * This file provides firmware functions to manage the following + * functionalities of the CORTEX: + * + Initialization and de-initialization functions + * + Peripheral Control functions + * + * @verbatim + ============================================================================== + ##### How to use this driver ##### + ============================================================================== + + [..] + *** How to configure Interrupts using Cortex HAL driver *** + =========================================================== + [..] + This section provide functions allowing to configure the NVIC interrupts (IRQ). + The Cortex-M3 exceptions are managed by CMSIS functions. + + (#) Configure the NVIC Priority Grouping using HAL_NVIC_SetPriorityGrouping() + function according to the following table. + + The table below gives the allowed values of the pre-emption priority and subpriority according + to the Priority Grouping configuration performed by HAL_NVIC_SetPriorityGrouping() function. + ========================================================================================================================== + NVIC_PriorityGroup | NVIC_IRQChannelPreemptionPriority | NVIC_IRQChannelSubPriority | Description + ========================================================================================================================== + NVIC_PRIORITYGROUP_0 | 0 | 0-15 | 0 bits for pre-emption priority + | | | 4 bits for subpriority + -------------------------------------------------------------------------------------------------------------------------- + NVIC_PRIORITYGROUP_1 | 0-1 | 0-7 | 1 bits for pre-emption priority + | | | 3 bits for subpriority + -------------------------------------------------------------------------------------------------------------------------- + NVIC_PRIORITYGROUP_2 | 0-3 | 0-3 | 2 bits for pre-emption priority + | | | 2 bits for subpriority + -------------------------------------------------------------------------------------------------------------------------- + NVIC_PRIORITYGROUP_3 | 0-7 | 0-1 | 3 bits for pre-emption priority + | | | 1 bits for subpriority + -------------------------------------------------------------------------------------------------------------------------- + NVIC_PRIORITYGROUP_4 | 0-15 | 0 | 4 bits for pre-emption priority + | | | 0 bits for subpriority + ========================================================================================================================== + (#) Configure the priority of the selected IRQ Channels using HAL_NVIC_SetPriority() + + (#) Enable the selected IRQ Channels using HAL_NVIC_EnableIRQ() + + + -@- When the NVIC_PRIORITYGROUP_0 is selected, IRQ pre-emption is no more possible. + The pending IRQ priority will be managed only by the sub priority. + + -@- IRQ priority order (sorted by highest to lowest priority): + (+@) Lowest pre-emption priority + (+@) Lowest sub priority + (+@) Lowest hardware priority (IRQ number) + + [..] + *** How to configure Systick using Cortex HAL driver *** + ======================================================== + [..] + Setup SysTick Timer for 1 msec interrupts. + + (+) The HAL_SYSTICK_Config()function calls the SysTick_Config() function which + is a CMSIS function that: + (++) Configures the SysTick Reload register with value passed as function parameter. + (++) Configures the SysTick IRQ priority to the lowest value (0x0F). + (++) Resets the SysTick Counter register. + (++) Configures the SysTick Counter clock source to be Core Clock Source (HCLK). + (++) Enables the SysTick Interrupt. + (++) Starts the SysTick Counter. + + (+) You can change the SysTick Clock source to be HCLK_Div8 by calling the function + HAL_SYSTICK_CLKSourceConfig(SYSTICK_CLKSOURCE_HCLK_DIV8) just after the + HAL_SYSTICK_Config() function call. + + (+) You can change the SysTick IRQ priority by calling the + HAL_NVIC_SetPriority(SysTick_IRQn,...) function just after the HAL_SYSTICK_Config() function + call. The HAL_NVIC_SetPriority() call the NVIC_SetPriority() function which is a CMSIS function. + + (+) To adjust the SysTick time base, use the following formula: + + Reload Value = SysTick Counter Clock (Hz) x Desired Time base (s) + (++) Reload Value is the parameter to be passed for HAL_SYSTICK_Config() function + (++) Reload Value should not exceed 0xFFFFFF + + @endverbatim + ****************************************************************************** + * @attention + * + *

© COPYRIGHT(c) 2016 STMicroelectronics

+ * + * Redistribution and use in source and binary forms, with or without modification, + * are permitted provided that the following conditions are met: + * 1. Redistributions of source code must retain the above copyright notice, + * this list of conditions and the following disclaimer. + * 2. Redistributions in binary form must reproduce the above copyright notice, + * this list of conditions and the following disclaimer in the documentation + * and/or other materials provided with the distribution. + * 3. Neither the name of STMicroelectronics nor the names of its contributors + * may be used to endorse or promote products derived from this software + * without specific prior written permission. + * + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" + * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE + * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE + * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE + * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL + * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR + * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER + * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, + * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE + * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. + * + ****************************************************************************** + */ + +/* Includes ------------------------------------------------------------------*/ +#include "stm32f1xx_hal.h" + +/** @addtogroup STM32F1xx_HAL_Driver + * @{ + */ + +/** @defgroup CORTEX CORTEX + * @brief CORTEX HAL module driver + * @{ + */ + +#ifdef HAL_CORTEX_MODULE_ENABLED + +/* Private typedef -----------------------------------------------------------*/ +/* Private define ------------------------------------------------------------*/ +/* Private macro -------------------------------------------------------------*/ +/* Private variables ---------------------------------------------------------*/ +/* Private function prototypes -----------------------------------------------*/ +/* Private functions ---------------------------------------------------------*/ + +/** @defgroup CORTEX_Exported_Functions CORTEX Exported Functions + * @{ + */ + + +/** @defgroup CORTEX_Exported_Functions_Group1 Initialization and de-initialization functions + * @brief Initialization and Configuration functions + * +@verbatim + ============================================================================== + ##### Initialization and de-initialization functions ##### + ============================================================================== + [..] + This section provide the Cortex HAL driver functions allowing to configure Interrupts + Systick functionalities + +@endverbatim + * @{ + */ + + +/** + * @brief Sets the priority grouping field (pre-emption priority and subpriority) + * using the required unlock sequence. + * @param PriorityGroup: The priority grouping bits length. + * This parameter can be one of the following values: + * @arg NVIC_PRIORITYGROUP_0: 0 bits for pre-emption priority + * 4 bits for subpriority + * @arg NVIC_PRIORITYGROUP_1: 1 bits for pre-emption priority + * 3 bits for subpriority + * @arg NVIC_PRIORITYGROUP_2: 2 bits for pre-emption priority + * 2 bits for subpriority + * @arg NVIC_PRIORITYGROUP_3: 3 bits for pre-emption priority + * 1 bits for subpriority + * @arg NVIC_PRIORITYGROUP_4: 4 bits for pre-emption priority + * 0 bits for subpriority + * @note When the NVIC_PriorityGroup_0 is selected, IRQ pre-emption is no more possible. + * The pending IRQ priority will be managed only by the subpriority. + * @retval None + */ +void HAL_NVIC_SetPriorityGrouping(uint32_t PriorityGroup) +{ + /* Check the parameters */ + assert_param(IS_NVIC_PRIORITY_GROUP(PriorityGroup)); + + /* Set the PRIGROUP[10:8] bits according to the PriorityGroup parameter value */ + NVIC_SetPriorityGrouping(PriorityGroup); +} + +/** + * @brief Sets the priority of an interrupt. + * @param IRQn: External interrupt number + * This parameter can be an enumerator of IRQn_Type enumeration + * (For the complete STM32 Devices IRQ Channels list, please refer to the appropriate CMSIS device file (stm32f10xxx.h)) + * @param PreemptPriority: The pre-emption priority for the IRQn channel. + * This parameter can be a value between 0 and 15 + * A lower priority value indicates a higher priority + * @param SubPriority: the subpriority level for the IRQ channel. + * This parameter can be a value between 0 and 15 + * A lower priority value indicates a higher priority. + * @retval None + */ +void HAL_NVIC_SetPriority(IRQn_Type IRQn, uint32_t PreemptPriority, uint32_t SubPriority) +{ + uint32_t prioritygroup = 0x00; + + /* Check the parameters */ + assert_param(IS_NVIC_SUB_PRIORITY(SubPriority)); + assert_param(IS_NVIC_PREEMPTION_PRIORITY(PreemptPriority)); + + prioritygroup = NVIC_GetPriorityGrouping(); + + NVIC_SetPriority(IRQn, NVIC_EncodePriority(prioritygroup, PreemptPriority, SubPriority)); +} + +/** + * @brief Enables a device specific interrupt in the NVIC interrupt controller. + * @note To configure interrupts priority correctly, the NVIC_PriorityGroupConfig() + * function should be called before. + * @param IRQn External interrupt number + * This parameter can be an enumerator of IRQn_Type enumeration + * (For the complete STM32 Devices IRQ Channels list, please refer to the appropriate CMSIS device file (stm32f10xxx.h)) + * @retval None + */ +void HAL_NVIC_EnableIRQ(IRQn_Type IRQn) +{ + /* Check the parameters */ + assert_param(IS_NVIC_DEVICE_IRQ(IRQn)); + + /* Enable interrupt */ + NVIC_EnableIRQ(IRQn); +} + +/** + * @brief Disables a device specific interrupt in the NVIC interrupt controller. + * @param IRQn External interrupt number + * This parameter can be an enumerator of IRQn_Type enumeration + * (For the complete STM32 Devices IRQ Channels list, please refer to the appropriate CMSIS device file (stm32f10xxx.h)) + * @retval None + */ +void HAL_NVIC_DisableIRQ(IRQn_Type IRQn) +{ + /* Check the parameters */ + assert_param(IS_NVIC_DEVICE_IRQ(IRQn)); + + + /* Disable interrupt */ + NVIC_DisableIRQ(IRQn); +} + +/** + * @brief Initiates a system reset request to reset the MCU. + * @retval None + */ +void HAL_NVIC_SystemReset(void) +{ + /* System Reset */ + NVIC_SystemReset(); +} + +/** + * @brief Initializes the System Timer and its interrupt, and starts the System Tick Timer. + * Counter is in free running mode to generate periodic interrupts. + * @param TicksNumb: Specifies the ticks Number of ticks between two interrupts. + * @retval status: - 0 Function succeeded. + * - 1 Function failed. + */ +uint32_t HAL_SYSTICK_Config(uint32_t TicksNumb) +{ + return SysTick_Config(TicksNumb); +} +/** + * @} + */ + +/** @defgroup CORTEX_Exported_Functions_Group2 Peripheral Control functions + * @brief Cortex control functions + * +@verbatim + ============================================================================== + ##### Peripheral Control functions ##### + ============================================================================== + [..] + This subsection provides a set of functions allowing to control the CORTEX + (NVIC, SYSTICK, MPU) functionalities. + + +@endverbatim + * @{ + */ + +#if (__MPU_PRESENT == 1) +/** + * @brief Initializes and configures the Region and the memory to be protected. + * @param MPU_Init: Pointer to a MPU_Region_InitTypeDef structure that contains + * the initialization and configuration information. + * @retval None + */ +void HAL_MPU_ConfigRegion(MPU_Region_InitTypeDef *MPU_Init) +{ + /* Check the parameters */ + assert_param(IS_MPU_REGION_NUMBER(MPU_Init->Number)); + assert_param(IS_MPU_REGION_ENABLE(MPU_Init->Enable)); + + /* Set the Region number */ + MPU->RNR = MPU_Init->Number; + + if ((MPU_Init->Enable) != RESET) + { + /* Check the parameters */ + assert_param(IS_MPU_INSTRUCTION_ACCESS(MPU_Init->DisableExec)); + assert_param(IS_MPU_REGION_PERMISSION_ATTRIBUTE(MPU_Init->AccessPermission)); + assert_param(IS_MPU_TEX_LEVEL(MPU_Init->TypeExtField)); + assert_param(IS_MPU_ACCESS_SHAREABLE(MPU_Init->IsShareable)); + assert_param(IS_MPU_ACCESS_CACHEABLE(MPU_Init->IsCacheable)); + assert_param(IS_MPU_ACCESS_BUFFERABLE(MPU_Init->IsBufferable)); + assert_param(IS_MPU_SUB_REGION_DISABLE(MPU_Init->SubRegionDisable)); + assert_param(IS_MPU_REGION_SIZE(MPU_Init->Size)); + + MPU->RBAR = MPU_Init->BaseAddress; + MPU->RASR = ((uint32_t)MPU_Init->DisableExec << MPU_RASR_XN_Pos) | + ((uint32_t)MPU_Init->AccessPermission << MPU_RASR_AP_Pos) | + ((uint32_t)MPU_Init->TypeExtField << MPU_RASR_TEX_Pos) | + ((uint32_t)MPU_Init->IsShareable << MPU_RASR_S_Pos) | + ((uint32_t)MPU_Init->IsCacheable << MPU_RASR_C_Pos) | + ((uint32_t)MPU_Init->IsBufferable << MPU_RASR_B_Pos) | + ((uint32_t)MPU_Init->SubRegionDisable << MPU_RASR_SRD_Pos) | + ((uint32_t)MPU_Init->Size << MPU_RASR_SIZE_Pos) | + ((uint32_t)MPU_Init->Enable << MPU_RASR_ENABLE_Pos); + } + else + { + MPU->RBAR = 0x00; + MPU->RASR = 0x00; + } +} +#endif /* __MPU_PRESENT */ + +/** + * @brief Gets the priority grouping field from the NVIC Interrupt Controller. + * @retval Priority grouping field (SCB->AIRCR [10:8] PRIGROUP field) + */ +uint32_t HAL_NVIC_GetPriorityGrouping(void) +{ + /* Get the PRIGROUP[10:8] field value */ + return NVIC_GetPriorityGrouping(); +} + +/** + * @brief Gets the priority of an interrupt. + * @param IRQn: External interrupt number + * This parameter can be an enumerator of IRQn_Type enumeration + * (For the complete STM32 Devices IRQ Channels list, please refer to the appropriate CMSIS device file (stm32f10xxx.h)) + * @param PriorityGroup: the priority grouping bits length. + * This parameter can be one of the following values: + * @arg NVIC_PRIORITYGROUP_0: 0 bits for pre-emption priority + * 4 bits for subpriority + * @arg NVIC_PRIORITYGROUP_1: 1 bits for pre-emption priority + * 3 bits for subpriority + * @arg NVIC_PRIORITYGROUP_2: 2 bits for pre-emption priority + * 2 bits for subpriority + * @arg NVIC_PRIORITYGROUP_3: 3 bits for pre-emption priority + * 1 bits for subpriority + * @arg NVIC_PRIORITYGROUP_4: 4 bits for pre-emption priority + * 0 bits for subpriority + * @param pPreemptPriority: Pointer on the Preemptive priority value (starting from 0). + * @param pSubPriority: Pointer on the Subpriority value (starting from 0). + * @retval None + */ +void HAL_NVIC_GetPriority(IRQn_Type IRQn, uint32_t PriorityGroup, uint32_t* pPreemptPriority, uint32_t* pSubPriority) +{ + /* Check the parameters */ + assert_param(IS_NVIC_PRIORITY_GROUP(PriorityGroup)); + /* Get priority for Cortex-M system or device specific interrupts */ + NVIC_DecodePriority(NVIC_GetPriority(IRQn), PriorityGroup, pPreemptPriority, pSubPriority); +} + +/** + * @brief Sets Pending bit of an external interrupt. + * @param IRQn External interrupt number + * This parameter can be an enumerator of IRQn_Type enumeration + * (For the complete STM32 Devices IRQ Channels list, please refer to the appropriate CMSIS device file (stm32f10xxx.h)) + * @retval None + */ +void HAL_NVIC_SetPendingIRQ(IRQn_Type IRQn) +{ + /* Set interrupt pending */ + NVIC_SetPendingIRQ(IRQn); +} + +/** + * @brief Gets Pending Interrupt (reads the pending register in the NVIC + * and returns the pending bit for the specified interrupt). + * @param IRQn External interrupt number + * This parameter can be an enumerator of IRQn_Type enumeration + * (For the complete STM32 Devices IRQ Channels list, please refer to the appropriate CMSIS device file (stm32f10xxx.h)) + * @retval status: - 0 Interrupt status is not pending. + * - 1 Interrupt status is pending. + */ +uint32_t HAL_NVIC_GetPendingIRQ(IRQn_Type IRQn) +{ + /* Return 1 if pending else 0 */ + return NVIC_GetPendingIRQ(IRQn); +} + +/** + * @brief Clears the pending bit of an external interrupt. + * @param IRQn External interrupt number + * This parameter can be an enumerator of IRQn_Type enumeration + * (For the complete STM32 Devices IRQ Channels list, please refer to the appropriate CMSIS device file (stm32f10xxx.h)) + * @retval None + */ +void HAL_NVIC_ClearPendingIRQ(IRQn_Type IRQn) +{ + /* Clear pending interrupt */ + NVIC_ClearPendingIRQ(IRQn); +} + +/** + * @brief Gets active interrupt ( reads the active register in NVIC and returns the active bit). + * @param IRQn External interrupt number + * This parameter can be an enumerator of IRQn_Type enumeration + * (For the complete STM32 Devices IRQ Channels list, please refer to the appropriate CMSIS device file (stm32f10xxx.h)) + * @retval status: - 0 Interrupt status is not pending. + * - 1 Interrupt status is pending. + */ +uint32_t HAL_NVIC_GetActive(IRQn_Type IRQn) +{ + /* Return 1 if active else 0 */ + return NVIC_GetActive(IRQn); +} + +/** + * @brief Configures the SysTick clock source. + * @param CLKSource: specifies the SysTick clock source. + * This parameter can be one of the following values: + * @arg SYSTICK_CLKSOURCE_HCLK_DIV8: AHB clock divided by 8 selected as SysTick clock source. + * @arg SYSTICK_CLKSOURCE_HCLK: AHB clock selected as SysTick clock source. + * @retval None + */ +void HAL_SYSTICK_CLKSourceConfig(uint32_t CLKSource) +{ + /* Check the parameters */ + assert_param(IS_SYSTICK_CLK_SOURCE(CLKSource)); + if (CLKSource == SYSTICK_CLKSOURCE_HCLK) + { + SysTick->CTRL |= SYSTICK_CLKSOURCE_HCLK; + } + else + { + SysTick->CTRL &= ~SYSTICK_CLKSOURCE_HCLK; + } +} + +/** + * @brief This function handles SYSTICK interrupt request. + * @retval None + */ +void HAL_SYSTICK_IRQHandler(void) +{ + HAL_SYSTICK_Callback(); +} + +/** + * @brief SYSTICK callback. + * @retval None + */ +__weak void HAL_SYSTICK_Callback(void) +{ + /* NOTE : This function Should not be modified, when the callback is needed, + the HAL_SYSTICK_Callback could be implemented in the user file + */ +} + +/** + * @} + */ + +/** + * @} + */ + +#endif /* HAL_CORTEX_MODULE_ENABLED */ +/** + * @} + */ + +/** + * @} + */ + +/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/ -- cgit v1.2.3