From a819d3cbddbb5294b98b2fd6590f9fff13491d85 Mon Sep 17 00:00:00 2001 From: Trygve Laugstøl Date: Sat, 27 May 2017 10:55:23 +0200 Subject: o Moving generated code to under bsp/. Renaming to match PCB. --- .../STM32F1xx_HAL_Driver/Src/stm32f1xx_hal_rcc.c | 1270 ++++++++++++++++++++ 1 file changed, 1270 insertions(+) create mode 100644 bsp/radio-controller-1/Drivers/STM32F1xx_HAL_Driver/Src/stm32f1xx_hal_rcc.c (limited to 'bsp/radio-controller-1/Drivers/STM32F1xx_HAL_Driver/Src/stm32f1xx_hal_rcc.c') diff --git a/bsp/radio-controller-1/Drivers/STM32F1xx_HAL_Driver/Src/stm32f1xx_hal_rcc.c b/bsp/radio-controller-1/Drivers/STM32F1xx_HAL_Driver/Src/stm32f1xx_hal_rcc.c new file mode 100644 index 0000000..e23f65c --- /dev/null +++ b/bsp/radio-controller-1/Drivers/STM32F1xx_HAL_Driver/Src/stm32f1xx_hal_rcc.c @@ -0,0 +1,1270 @@ +/** + ****************************************************************************** + * @file stm32f1xx_hal_rcc.c + * @author MCD Application Team + * @version V1.0.4 + * @date 29-April-2016 + * @brief RCC HAL module driver. + * This file provides firmware functions to manage the following + * functionalities of the Reset and Clock Control (RCC) peripheral: + * + Initialization and de-initialization functions + * + Peripheral Control functions + * + @verbatim + ============================================================================== + ##### RCC specific features ##### + ============================================================================== + [..] + After reset the device is running from Internal High Speed oscillator + (HSI 8MHz) with Flash 0 wait state, Flash prefetch buffer is enabled, + and all peripherals are off except internal SRAM, Flash and JTAG. + (+) There is no prescaler on High speed (AHB) and Low speed (APB) buses; + all peripherals mapped on these buses are running at HSI speed. + (+) The clock for all peripherals is switched off, except the SRAM and FLASH. + (+) All GPIOs are in input floating state, except the JTAG pins which + are assigned to be used for debug purpose. + [..] Once the device started from reset, the user application has to: + (+) Configure the clock source to be used to drive the System clock + (if the application needs higher frequency/performance) + (+) Configure the System clock frequency and Flash settings + (+) Configure the AHB and APB buses prescalers + (+) Enable the clock for the peripheral(s) to be used + (+) Configure the clock source(s) for peripherals whose clocks are not + derived from the System clock (I2S, RTC, ADC, USB OTG FS) + + ##### RCC Limitations ##### + ============================================================================== + [..] + A delay between an RCC peripheral clock enable and the effective peripheral + enabling should be taken into account in order to manage the peripheral read/write + from/to registers. + (+) This delay depends on the peripheral mapping. + (++) AHB & APB peripherals, 1 dummy read is necessary + + [..] + Workarounds: + (#) For AHB & APB peripherals, a dummy read to the peripheral register has been + inserted in each __HAL_RCC_PPP_CLK_ENABLE() macro. + + @endverbatim + ****************************************************************************** + * @attention + * + *

© COPYRIGHT(c) 2016 STMicroelectronics

+ * + * Redistribution and use in source and binary forms, with or without modification, + * are permitted provided that the following conditions are met: + * 1. Redistributions of source code must retain the above copyright notice, + * this list of conditions and the following disclaimer. + * 2. Redistributions in binary form must reproduce the above copyright notice, + * this list of conditions and the following disclaimer in the documentation + * and/or other materials provided with the distribution. + * 3. Neither the name of STMicroelectronics nor the names of its contributors + * may be used to endorse or promote products derived from this software + * without specific prior written permission. + * + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" + * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE + * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE + * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE + * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL + * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR + * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER + * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, + * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE + * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. + * + ****************************************************************************** +*/ + +/* Includes ------------------------------------------------------------------*/ +#include "stm32f1xx_hal.h" + +/** @addtogroup STM32F1xx_HAL_Driver + * @{ + */ + +/** @defgroup RCC RCC +* @brief RCC HAL module driver + * @{ + */ + +#ifdef HAL_RCC_MODULE_ENABLED + +/* Private typedef -----------------------------------------------------------*/ +/* Private define ------------------------------------------------------------*/ +/** @defgroup RCC_Private_Constants RCC Private Constants + * @{ + */ +/* Bits position in in the CFGR register */ +#define RCC_CFGR_HPRE_BITNUMBER POSITION_VAL(RCC_CFGR_HPRE) +#define RCC_CFGR_PPRE1_BITNUMBER POSITION_VAL(RCC_CFGR_PPRE1) +#define RCC_CFGR_PPRE2_BITNUMBER POSITION_VAL(RCC_CFGR_PPRE2) +/** + * @} + */ +/* Private macro -------------------------------------------------------------*/ +/** @defgroup RCC_Private_Macros RCC Private Macros + * @{ + */ + +#define MCO1_CLK_ENABLE() __HAL_RCC_GPIOA_CLK_ENABLE() +#define MCO1_GPIO_PORT GPIOA +#define MCO1_PIN GPIO_PIN_8 + +/** + * @} + */ + +/* Private variables ---------------------------------------------------------*/ +/** @defgroup RCC_Private_Variables RCC Private Variables + * @{ + */ +/** + * @} + */ + +/* Private function prototypes -----------------------------------------------*/ +/* Exported functions ---------------------------------------------------------*/ + +/** @defgroup RCC_Exported_Functions RCC Exported Functions + * @{ + */ + +/** @defgroup RCC_Exported_Functions_Group1 Initialization and de-initialization functions + * @brief Initialization and Configuration functions + * + @verbatim + =============================================================================== + ##### Initialization and de-initialization functions ##### + =============================================================================== + [..] + This section provides functions allowing to configure the internal/external oscillators + (HSE, HSI, LSE, LSI, PLL, CSS and MCO) and the System buses clocks (SYSCLK, AHB, APB1 + and APB2). + + [..] Internal/external clock and PLL configuration + (#) HSI (high-speed internal), 8 MHz factory-trimmed RC used directly or through + the PLL as System clock source. + (#) LSI (low-speed internal), ~40 KHz low consumption RC used as IWDG and/or RTC + clock source. + + (#) HSE (high-speed external), 4 to 24 MHz (STM32F100xx) or 4 to 16 MHz (STM32F101x/STM32F102x/STM32F103x) or 3 to 25 MHz (STM32F105x/STM32F107x) crystal oscillator used directly or + through the PLL as System clock source. Can be used also as RTC clock source. + + (#) LSE (low-speed external), 32 KHz oscillator used as RTC clock source. + + (#) PLL (clocked by HSI or HSE), featuring different output clocks: + (++) The first output is used to generate the high speed system clock (up to 72 MHz for STM32F10xxx or up to 24 MHz for STM32F100xx) + (++) The second output is used to generate the clock for the USB OTG FS (48 MHz) + + (#) CSS (Clock security system), once enable using the macro __HAL_RCC_CSS_ENABLE() + and if a HSE clock failure occurs(HSE used directly or through PLL as System + clock source), the System clocks automatically switched to HSI and an interrupt + is generated if enabled. The interrupt is linked to the Cortex-M3 NMI + (Non-Maskable Interrupt) exception vector. + + (#) MCO1 (microcontroller clock output), used to output SYSCLK, HSI, + HSE or PLL clock (divided by 2) on PA8 pin + PLL2CLK, PLL3CLK/2, PLL3CLK and XTI for STM32F105x/STM32F107x + + [..] System, AHB and APB buses clocks configuration + (#) Several clock sources can be used to drive the System clock (SYSCLK): HSI, + HSE and PLL. + The AHB clock (HCLK) is derived from System clock through configurable + prescaler and used to clock the CPU, memory and peripherals mapped + on AHB bus (DMA, GPIO...). APB1 (PCLK1) and APB2 (PCLK2) clocks are derived + from AHB clock through configurable prescalers and used to clock + the peripherals mapped on these buses. You can use + "@ref HAL_RCC_GetSysClockFreq()" function to retrieve the frequencies of these clocks. + + -@- All the peripheral clocks are derived from the System clock (SYSCLK) except: + (+@) RTC: RTC clock can be derived either from the LSI, LSE or HSE clock + divided by 128. + (+@) USB OTG FS and RTC: USB OTG FS require a frequency equal to 48 MHz + to work correctly. This clock is derived of the main PLL through PLL Multiplier. + (+@) I2S interface on STM32F105x/STM32F107x can be derived from PLL3CLK + (+@) IWDG clock which is always the LSI clock. + + (#) For STM32F10xxx, the maximum frequency of the SYSCLK and HCLK/PCLK2 is 72 MHz, PCLK1 36 MHz. + For STM32F100xx, the maximum frequency of the SYSCLK and HCLK/PCLK1/PCLK2 is 24 MHz. + Depending on the SYSCLK frequency, the flash latency should be adapted accordingly. + @endverbatim + * @{ + */ + +/* + Additional consideration on the SYSCLK based on Latency settings: + +-----------------------------------------------+ + | Latency | SYSCLK clock frequency (MHz) | + |---------------|-------------------------------| + |0WS(1CPU cycle)| 0 < SYSCLK <= 24 | + |---------------|-------------------------------| + |1WS(2CPU cycle)| 24 < SYSCLK <= 48 | + |---------------|-------------------------------| + |2WS(3CPU cycle)| 48 < SYSCLK <= 72 | + +-----------------------------------------------+ + */ + +/** + * @brief Resets the RCC clock configuration to the default reset state. + * @note The default reset state of the clock configuration is given below: + * - HSI ON and used as system clock source + * - HSE and PLL OFF + * - AHB, APB1 and APB2 prescaler set to 1. + * - CSS and MCO1 OFF + * - All interrupts disabled + * @note This function does not modify the configuration of the + * - Peripheral clocks + * - LSI, LSE and RTC clocks + * @retval None + */ +void HAL_RCC_DeInit(void) +{ + /* Switch SYSCLK to HSI */ + CLEAR_BIT(RCC->CFGR, RCC_CFGR_SW); + + /* Reset HSEON, CSSON, & PLLON bits */ + CLEAR_BIT(RCC->CR, RCC_CR_HSEON | RCC_CR_CSSON | RCC_CR_PLLON); + + /* Reset HSEBYP bit */ + CLEAR_BIT(RCC->CR, RCC_CR_HSEBYP); + + /* Reset CFGR register */ + CLEAR_REG(RCC->CFGR); + + /* Set HSITRIM bits to the reset value */ + MODIFY_REG(RCC->CR, RCC_CR_HSITRIM, ((uint32_t)0x10 << POSITION_VAL(RCC_CR_HSITRIM))); + +#if (defined(STM32F105xC) || defined(STM32F107xC) || defined (STM32F100xB) || defined (STM32F100xE)) + /* Reset CFGR2 register */ + CLEAR_REG(RCC->CFGR2); + +#endif /* STM32F105xC || STM32F107xC || STM32F100xB || STM32F100xE */ + /* Disable all interrupts */ + CLEAR_REG(RCC->CIR); + + /* Update the SystemCoreClock global variable */ + SystemCoreClock = HSI_VALUE; +} + +/** + * @brief Initializes the RCC Oscillators according to the specified parameters in the + * RCC_OscInitTypeDef. + * @param RCC_OscInitStruct pointer to an RCC_OscInitTypeDef structure that + * contains the configuration information for the RCC Oscillators. + * @note The PLL is not disabled when used as system clock. + * @note The PLL is not disabled when USB OTG FS clock is enabled (specific to devices with USB FS) + * @note Transitions LSE Bypass to LSE On and LSE On to LSE Bypass are not + * supported by this macro. User should request a transition to LSE Off + * first and then LSE On or LSE Bypass. + * @note Transition HSE Bypass to HSE On and HSE On to HSE Bypass are not + * supported by this macro. User should request a transition to HSE Off + * first and then HSE On or HSE Bypass. + * @retval HAL status + */ +HAL_StatusTypeDef HAL_RCC_OscConfig(RCC_OscInitTypeDef *RCC_OscInitStruct) +{ + uint32_t tickstart = 0; + + /* Check the parameters */ + assert_param(RCC_OscInitStruct != NULL); + assert_param(IS_RCC_OSCILLATORTYPE(RCC_OscInitStruct->OscillatorType)); + + /*------------------------------- HSE Configuration ------------------------*/ + if(((RCC_OscInitStruct->OscillatorType) & RCC_OSCILLATORTYPE_HSE) == RCC_OSCILLATORTYPE_HSE) + { + /* Check the parameters */ + assert_param(IS_RCC_HSE(RCC_OscInitStruct->HSEState)); + + /* When the HSE is used as system clock or clock source for PLL in these cases it is not allowed to be disabled */ + if((__HAL_RCC_GET_SYSCLK_SOURCE() == RCC_SYSCLKSOURCE_STATUS_HSE) + || ((__HAL_RCC_GET_SYSCLK_SOURCE() == RCC_SYSCLKSOURCE_STATUS_PLLCLK) && (__HAL_RCC_GET_PLL_OSCSOURCE() == RCC_PLLSOURCE_HSE))) + { + if((__HAL_RCC_GET_FLAG(RCC_FLAG_HSERDY) != RESET) && (RCC_OscInitStruct->HSEState == RCC_HSE_OFF)) + { + return HAL_ERROR; + } + } + else + { + /* Set the new HSE configuration ---------------------------------------*/ + __HAL_RCC_HSE_CONFIG(RCC_OscInitStruct->HSEState); + + + /* Check the HSE State */ + if(RCC_OscInitStruct->HSEState != RCC_HSE_OFF) + { + /* Get Start Tick */ + tickstart = HAL_GetTick(); + + /* Wait till HSE is ready */ + while(__HAL_RCC_GET_FLAG(RCC_FLAG_HSERDY) == RESET) + { + if((HAL_GetTick() - tickstart ) > HSE_TIMEOUT_VALUE) + { + return HAL_TIMEOUT; + } + } + } + else + { + /* Get Start Tick */ + tickstart = HAL_GetTick(); + + /* Wait till HSE is disabled */ + while(__HAL_RCC_GET_FLAG(RCC_FLAG_HSERDY) != RESET) + { + if((HAL_GetTick() - tickstart ) > HSE_TIMEOUT_VALUE) + { + return HAL_TIMEOUT; + } + } + } + } + } + /*----------------------------- HSI Configuration --------------------------*/ + if(((RCC_OscInitStruct->OscillatorType) & RCC_OSCILLATORTYPE_HSI) == RCC_OSCILLATORTYPE_HSI) + { + /* Check the parameters */ + assert_param(IS_RCC_HSI(RCC_OscInitStruct->HSIState)); + assert_param(IS_RCC_CALIBRATION_VALUE(RCC_OscInitStruct->HSICalibrationValue)); + + /* Check if HSI is used as system clock or as PLL source when PLL is selected as system clock */ + if((__HAL_RCC_GET_SYSCLK_SOURCE() == RCC_SYSCLKSOURCE_STATUS_HSI) + || ((__HAL_RCC_GET_SYSCLK_SOURCE() == RCC_SYSCLKSOURCE_STATUS_PLLCLK) && (__HAL_RCC_GET_PLL_OSCSOURCE() == RCC_PLLSOURCE_HSI_DIV2))) + { + /* When HSI is used as system clock it will not disabled */ + if((__HAL_RCC_GET_FLAG(RCC_FLAG_HSIRDY) != RESET) && (RCC_OscInitStruct->HSIState != RCC_HSI_ON)) + { + return HAL_ERROR; + } + /* Otherwise, just the calibration is allowed */ + else + { + /* Adjusts the Internal High Speed oscillator (HSI) calibration value.*/ + __HAL_RCC_HSI_CALIBRATIONVALUE_ADJUST(RCC_OscInitStruct->HSICalibrationValue); + } + } + else + { + /* Check the HSI State */ + if(RCC_OscInitStruct->HSIState != RCC_HSI_OFF) + { + /* Enable the Internal High Speed oscillator (HSI). */ + __HAL_RCC_HSI_ENABLE(); + + /* Get Start Tick */ + tickstart = HAL_GetTick(); + + /* Wait till HSI is ready */ + while(__HAL_RCC_GET_FLAG(RCC_FLAG_HSIRDY) == RESET) + { + if((HAL_GetTick() - tickstart ) > HSI_TIMEOUT_VALUE) + { + return HAL_TIMEOUT; + } + } + + /* Adjusts the Internal High Speed oscillator (HSI) calibration value.*/ + __HAL_RCC_HSI_CALIBRATIONVALUE_ADJUST(RCC_OscInitStruct->HSICalibrationValue); + } + else + { + /* Disable the Internal High Speed oscillator (HSI). */ + __HAL_RCC_HSI_DISABLE(); + + /* Get Start Tick */ + tickstart = HAL_GetTick(); + + /* Wait till HSI is disabled */ + while(__HAL_RCC_GET_FLAG(RCC_FLAG_HSIRDY) != RESET) + { + if((HAL_GetTick() - tickstart ) > HSI_TIMEOUT_VALUE) + { + return HAL_TIMEOUT; + } + } + } + } + } + /*------------------------------ LSI Configuration -------------------------*/ + if(((RCC_OscInitStruct->OscillatorType) & RCC_OSCILLATORTYPE_LSI) == RCC_OSCILLATORTYPE_LSI) + { + /* Check the parameters */ + assert_param(IS_RCC_LSI(RCC_OscInitStruct->LSIState)); + + /* Check the LSI State */ + if(RCC_OscInitStruct->LSIState != RCC_LSI_OFF) + { + /* Enable the Internal Low Speed oscillator (LSI). */ + __HAL_RCC_LSI_ENABLE(); + + /* Get Start Tick */ + tickstart = HAL_GetTick(); + + /* Wait till LSI is ready */ + while(__HAL_RCC_GET_FLAG(RCC_FLAG_LSIRDY) == RESET) + { + if((HAL_GetTick() - tickstart ) > LSI_TIMEOUT_VALUE) + { + return HAL_TIMEOUT; + } + } + /* To have a fully stabilized clock in the specified range, a software delay of 1ms + should be added.*/ + HAL_Delay(1); + } + else + { + /* Disable the Internal Low Speed oscillator (LSI). */ + __HAL_RCC_LSI_DISABLE(); + + /* Get Start Tick */ + tickstart = HAL_GetTick(); + + /* Wait till LSI is disabled */ + while(__HAL_RCC_GET_FLAG(RCC_FLAG_LSIRDY) != RESET) + { + if((HAL_GetTick() - tickstart ) > LSI_TIMEOUT_VALUE) + { + return HAL_TIMEOUT; + } + } + } + } + /*------------------------------ LSE Configuration -------------------------*/ + if(((RCC_OscInitStruct->OscillatorType) & RCC_OSCILLATORTYPE_LSE) == RCC_OSCILLATORTYPE_LSE) + { + /* Check the parameters */ + assert_param(IS_RCC_LSE(RCC_OscInitStruct->LSEState)); + + /* Enable Power Clock*/ + __HAL_RCC_PWR_CLK_ENABLE(); + + /* Enable write access to Backup domain */ + SET_BIT(PWR->CR, PWR_CR_DBP); + + /* Wait for Backup domain Write protection disable */ + tickstart = HAL_GetTick(); + + while((PWR->CR & PWR_CR_DBP) == RESET) + { + if((HAL_GetTick() - tickstart) > RCC_DBP_TIMEOUT_VALUE) + { + return HAL_TIMEOUT; + } + } + + /* Set the new LSE configuration -----------------------------------------*/ + __HAL_RCC_LSE_CONFIG(RCC_OscInitStruct->LSEState); + /* Check the LSE State */ + if(RCC_OscInitStruct->LSEState != RCC_LSE_OFF) + { + /* Get Start Tick */ + tickstart = HAL_GetTick(); + + /* Wait till LSE is ready */ + while(__HAL_RCC_GET_FLAG(RCC_FLAG_LSERDY) == RESET) + { + if((HAL_GetTick() - tickstart ) > RCC_LSE_TIMEOUT_VALUE) + { + return HAL_TIMEOUT; + } + } + } + else + { + /* Get Start Tick */ + tickstart = HAL_GetTick(); + + /* Wait till LSE is disabled */ + while(__HAL_RCC_GET_FLAG(RCC_FLAG_LSERDY) != RESET) + { + if((HAL_GetTick() - tickstart ) > RCC_LSE_TIMEOUT_VALUE) + { + return HAL_TIMEOUT; + } + } + } + } + +#if defined(RCC_CR_PLL2ON) + /*-------------------------------- PLL2 Configuration -----------------------*/ + /* Check the parameters */ + assert_param(IS_RCC_PLL2(RCC_OscInitStruct->PLL2.PLL2State)); + if ((RCC_OscInitStruct->PLL2.PLL2State) != RCC_PLL2_NONE) + { + /* This bit can not be cleared if the PLL2 clock is used indirectly as system + clock (i.e. it is used as PLL clock entry that is used as system clock). */ + if((__HAL_RCC_GET_PLL_OSCSOURCE() == RCC_PLLSOURCE_HSE) && \ + (__HAL_RCC_GET_SYSCLK_SOURCE() == RCC_SYSCLKSOURCE_STATUS_PLLCLK) && \ + ((READ_BIT(RCC->CFGR2,RCC_CFGR2_PREDIV1SRC)) == RCC_CFGR2_PREDIV1SRC_PLL2)) + { + return HAL_ERROR; + } + else + { + if((RCC_OscInitStruct->PLL2.PLL2State) == RCC_PLL2_ON) + { + /* Check the parameters */ + assert_param(IS_RCC_PLL2_MUL(RCC_OscInitStruct->PLL2.PLL2MUL)); + assert_param(IS_RCC_HSE_PREDIV2(RCC_OscInitStruct->PLL2.HSEPrediv2Value)); + + /* Prediv2 can be written only when the PLLI2S is disabled. */ + /* Return an error only if new value is different from the programmed value */ + if (HAL_IS_BIT_SET(RCC->CR,RCC_CR_PLL3ON) && \ + (__HAL_RCC_HSE_GET_PREDIV2() != RCC_OscInitStruct->PLL2.HSEPrediv2Value)) + { + return HAL_ERROR; + } + + /* Disable the main PLL2. */ + __HAL_RCC_PLL2_DISABLE(); + + /* Get Start Tick */ + tickstart = HAL_GetTick(); + + /* Wait till PLL2 is disabled */ + while(__HAL_RCC_GET_FLAG(RCC_FLAG_PLL2RDY) != RESET) + { + if((HAL_GetTick() - tickstart ) > PLL2_TIMEOUT_VALUE) + { + return HAL_TIMEOUT; + } + } + + /* Configure the HSE prediv2 factor --------------------------------*/ + __HAL_RCC_HSE_PREDIV2_CONFIG(RCC_OscInitStruct->PLL2.HSEPrediv2Value); + + /* Configure the main PLL2 multiplication factors. */ + __HAL_RCC_PLL2_CONFIG(RCC_OscInitStruct->PLL2.PLL2MUL); + + /* Enable the main PLL2. */ + __HAL_RCC_PLL2_ENABLE(); + + /* Get Start Tick */ + tickstart = HAL_GetTick(); + + /* Wait till PLL2 is ready */ + while(__HAL_RCC_GET_FLAG(RCC_FLAG_PLL2RDY) == RESET) + { + if((HAL_GetTick() - tickstart ) > PLL2_TIMEOUT_VALUE) + { + return HAL_TIMEOUT; + } + } + } + else + { + /* Set PREDIV1 source to HSE */ + CLEAR_BIT(RCC->CFGR2, RCC_CFGR2_PREDIV1SRC); + + /* Disable the main PLL2. */ + __HAL_RCC_PLL2_DISABLE(); + + /* Get Start Tick */ + tickstart = HAL_GetTick(); + + /* Wait till PLL2 is disabled */ + while(__HAL_RCC_GET_FLAG(RCC_FLAG_PLL2RDY) != RESET) + { + if((HAL_GetTick() - tickstart ) > PLL2_TIMEOUT_VALUE) + { + return HAL_TIMEOUT; + } + } + } + } + } + +#endif /* RCC_CR_PLL2ON */ + /*-------------------------------- PLL Configuration -----------------------*/ + /* Check the parameters */ + assert_param(IS_RCC_PLL(RCC_OscInitStruct->PLL.PLLState)); + if ((RCC_OscInitStruct->PLL.PLLState) != RCC_PLL_NONE) + { + /* Check if the PLL is used as system clock or not */ + if(__HAL_RCC_GET_SYSCLK_SOURCE() != RCC_SYSCLKSOURCE_STATUS_PLLCLK) + { + if((RCC_OscInitStruct->PLL.PLLState) == RCC_PLL_ON) + { + /* Check the parameters */ + assert_param(IS_RCC_PLLSOURCE(RCC_OscInitStruct->PLL.PLLSource)); + assert_param(IS_RCC_PLL_MUL(RCC_OscInitStruct->PLL.PLLMUL)); + + /* Disable the main PLL. */ + __HAL_RCC_PLL_DISABLE(); + + /* Get Start Tick */ + tickstart = HAL_GetTick(); + + /* Wait till PLL is disabled */ + while(__HAL_RCC_GET_FLAG(RCC_FLAG_PLLRDY) != RESET) + { + if((HAL_GetTick() - tickstart ) > PLL_TIMEOUT_VALUE) + { + return HAL_TIMEOUT; + } + } + + /* Configure the HSE prediv factor --------------------------------*/ + /* It can be written only when the PLL is disabled. Not used in PLL source is different than HSE */ + if(RCC_OscInitStruct->PLL.PLLSource == RCC_PLLSOURCE_HSE) + { + /* Check the parameter */ + assert_param(IS_RCC_HSE_PREDIV(RCC_OscInitStruct->HSEPredivValue)); +#if defined(RCC_CFGR2_PREDIV1SRC) + assert_param(IS_RCC_PREDIV1_SOURCE(RCC_OscInitStruct->Prediv1Source)); + + /* Set PREDIV1 source */ + SET_BIT(RCC->CFGR2, RCC_OscInitStruct->Prediv1Source); +#endif /* RCC_CFGR2_PREDIV1SRC */ + + /* Set PREDIV1 Value */ + __HAL_RCC_HSE_PREDIV_CONFIG(RCC_OscInitStruct->HSEPredivValue); + } + + /* Configure the main PLL clock source and multiplication factors. */ + __HAL_RCC_PLL_CONFIG(RCC_OscInitStruct->PLL.PLLSource, + RCC_OscInitStruct->PLL.PLLMUL); + /* Enable the main PLL. */ + __HAL_RCC_PLL_ENABLE(); + + /* Get Start Tick */ + tickstart = HAL_GetTick(); + + /* Wait till PLL is ready */ + while(__HAL_RCC_GET_FLAG(RCC_FLAG_PLLRDY) == RESET) + { + if((HAL_GetTick() - tickstart ) > PLL_TIMEOUT_VALUE) + { + return HAL_TIMEOUT; + } + } + } + else + { + /* Disable the main PLL. */ + __HAL_RCC_PLL_DISABLE(); + + /* Get Start Tick */ + tickstart = HAL_GetTick(); + + /* Wait till PLL is disabled */ + while(__HAL_RCC_GET_FLAG(RCC_FLAG_PLLRDY) != RESET) + { + if((HAL_GetTick() - tickstart ) > PLL_TIMEOUT_VALUE) + { + return HAL_TIMEOUT; + } + } + } + } + else + { + return HAL_ERROR; + } + } + + return HAL_OK; +} + +/** + * @brief Initializes the CPU, AHB and APB buses clocks according to the specified + * parameters in the RCC_ClkInitStruct. + * @param RCC_ClkInitStruct pointer to an RCC_OscInitTypeDef structure that + * contains the configuration information for the RCC peripheral. + * @param FLatency FLASH Latency + * The value of this parameter depend on device used within the same series + * @note The SystemCoreClock CMSIS variable is used to store System Clock Frequency + * and updated by @ref HAL_RCC_GetHCLKFreq() function called within this function + * + * @note The HSI is used (enabled by hardware) as system clock source after + * start-up from Reset, wake-up from STOP and STANDBY mode, or in case + * of failure of the HSE used directly or indirectly as system clock + * (if the Clock Security System CSS is enabled). + * + * @note A switch from one clock source to another occurs only if the target + * clock source is ready (clock stable after start-up delay or PLL locked). + * If a clock source which is not yet ready is selected, the switch will + * occur when the clock source will be ready. + * You can use @ref HAL_RCC_GetClockConfig() function to know which clock is + * currently used as system clock source. + * @retval HAL status + */ +HAL_StatusTypeDef HAL_RCC_ClockConfig(RCC_ClkInitTypeDef *RCC_ClkInitStruct, uint32_t FLatency) +{ + uint32_t tickstart = 0; + + /* Check the parameters */ + assert_param(RCC_ClkInitStruct != NULL); + assert_param(IS_RCC_CLOCKTYPE(RCC_ClkInitStruct->ClockType)); + assert_param(IS_FLASH_LATENCY(FLatency)); + + /* To correctly read data from FLASH memory, the number of wait states (LATENCY) + must be correctly programmed according to the frequency of the CPU clock + (HCLK) of the device. */ + +#if defined(FLASH_ACR_LATENCY) + /* Increasing the number of wait states because of higher CPU frequency */ + if(FLatency > (FLASH->ACR & FLASH_ACR_LATENCY)) + { + /* Program the new number of wait states to the LATENCY bits in the FLASH_ACR register */ + __HAL_FLASH_SET_LATENCY(FLatency); + + /* Check that the new number of wait states is taken into account to access the Flash + memory by reading the FLASH_ACR register */ + if((FLASH->ACR & FLASH_ACR_LATENCY) != FLatency) + { + return HAL_ERROR; + } + } + +#endif /* FLASH_ACR_LATENCY */ + /*-------------------------- HCLK Configuration --------------------------*/ + if(((RCC_ClkInitStruct->ClockType) & RCC_CLOCKTYPE_HCLK) == RCC_CLOCKTYPE_HCLK) + { + assert_param(IS_RCC_HCLK(RCC_ClkInitStruct->AHBCLKDivider)); + MODIFY_REG(RCC->CFGR, RCC_CFGR_HPRE, RCC_ClkInitStruct->AHBCLKDivider); + } + + /*------------------------- SYSCLK Configuration ---------------------------*/ + if(((RCC_ClkInitStruct->ClockType) & RCC_CLOCKTYPE_SYSCLK) == RCC_CLOCKTYPE_SYSCLK) + { + assert_param(IS_RCC_SYSCLKSOURCE(RCC_ClkInitStruct->SYSCLKSource)); + + /* HSE is selected as System Clock Source */ + if(RCC_ClkInitStruct->SYSCLKSource == RCC_SYSCLKSOURCE_HSE) + { + /* Check the HSE ready flag */ + if(__HAL_RCC_GET_FLAG(RCC_FLAG_HSERDY) == RESET) + { + return HAL_ERROR; + } + } + /* PLL is selected as System Clock Source */ + else if(RCC_ClkInitStruct->SYSCLKSource == RCC_SYSCLKSOURCE_PLLCLK) + { + /* Check the PLL ready flag */ + if(__HAL_RCC_GET_FLAG(RCC_FLAG_PLLRDY) == RESET) + { + return HAL_ERROR; + } + } + /* HSI is selected as System Clock Source */ + else + { + /* Check the HSI ready flag */ + if(__HAL_RCC_GET_FLAG(RCC_FLAG_HSIRDY) == RESET) + { + return HAL_ERROR; + } + } + __HAL_RCC_SYSCLK_CONFIG(RCC_ClkInitStruct->SYSCLKSource); + + /* Get Start Tick */ + tickstart = HAL_GetTick(); + + if(RCC_ClkInitStruct->SYSCLKSource == RCC_SYSCLKSOURCE_HSE) + { + while (__HAL_RCC_GET_SYSCLK_SOURCE() != RCC_SYSCLKSOURCE_STATUS_HSE) + { + if((HAL_GetTick() - tickstart ) > CLOCKSWITCH_TIMEOUT_VALUE) + { + return HAL_TIMEOUT; + } + } + } + else if(RCC_ClkInitStruct->SYSCLKSource == RCC_SYSCLKSOURCE_PLLCLK) + { + while (__HAL_RCC_GET_SYSCLK_SOURCE() != RCC_SYSCLKSOURCE_STATUS_PLLCLK) + { + if((HAL_GetTick() - tickstart ) > CLOCKSWITCH_TIMEOUT_VALUE) + { + return HAL_TIMEOUT; + } + } + } + else + { + while (__HAL_RCC_GET_SYSCLK_SOURCE() != RCC_SYSCLKSOURCE_STATUS_HSI) + { + if((HAL_GetTick() - tickstart ) > CLOCKSWITCH_TIMEOUT_VALUE) + { + return HAL_TIMEOUT; + } + } + } + } +#if defined(FLASH_ACR_LATENCY) + /* Decreasing the number of wait states because of lower CPU frequency */ + if(FLatency < (FLASH->ACR & FLASH_ACR_LATENCY)) + { + /* Program the new number of wait states to the LATENCY bits in the FLASH_ACR register */ + __HAL_FLASH_SET_LATENCY(FLatency); + + /* Check that the new number of wait states is taken into account to access the Flash + memory by reading the FLASH_ACR register */ + if((FLASH->ACR & FLASH_ACR_LATENCY) != FLatency) + { + return HAL_ERROR; + } + } +#endif /* FLASH_ACR_LATENCY */ + + /*-------------------------- PCLK1 Configuration ---------------------------*/ + if(((RCC_ClkInitStruct->ClockType) & RCC_CLOCKTYPE_PCLK1) == RCC_CLOCKTYPE_PCLK1) + { + assert_param(IS_RCC_PCLK(RCC_ClkInitStruct->APB1CLKDivider)); + MODIFY_REG(RCC->CFGR, RCC_CFGR_PPRE1, RCC_ClkInitStruct->APB1CLKDivider); + } + + /*-------------------------- PCLK2 Configuration ---------------------------*/ + if(((RCC_ClkInitStruct->ClockType) & RCC_CLOCKTYPE_PCLK2) == RCC_CLOCKTYPE_PCLK2) + { + assert_param(IS_RCC_PCLK(RCC_ClkInitStruct->APB2CLKDivider)); + MODIFY_REG(RCC->CFGR, RCC_CFGR_PPRE2, ((RCC_ClkInitStruct->APB2CLKDivider) << 3)); + } + + /* Update the SystemCoreClock global variable */ + SystemCoreClock = HAL_RCC_GetSysClockFreq() >> AHBPrescTable[(RCC->CFGR & RCC_CFGR_HPRE)>> RCC_CFGR_HPRE_BITNUMBER]; + + /* Configure the source of time base considering new system clocks settings*/ + HAL_InitTick (TICK_INT_PRIORITY); + + return HAL_OK; +} + +/** + * @} + */ + +/** @defgroup RCC_Exported_Functions_Group2 Peripheral Control functions + * @brief RCC clocks control functions + * + @verbatim + =============================================================================== + ##### Peripheral Control functions ##### + =============================================================================== + [..] + This subsection provides a set of functions allowing to control the RCC Clocks + frequencies. + + @endverbatim + * @{ + */ + +/** + * @brief Selects the clock source to output on MCO pin. + * @note MCO pin should be configured in alternate function mode. + * @param RCC_MCOx specifies the output direction for the clock source. + * This parameter can be one of the following values: + * @arg @ref RCC_MCO1 Clock source to output on MCO1 pin(PA8). + * @param RCC_MCOSource specifies the clock source to output. + * This parameter can be one of the following values: + * @arg @ref RCC_MCO1SOURCE_NOCLOCK No clock selected as MCO clock + * @arg @ref RCC_MCO1SOURCE_SYSCLK System clock selected as MCO clock + * @arg @ref RCC_MCO1SOURCE_HSI HSI selected as MCO clock + * @arg @ref RCC_MCO1SOURCE_HSE HSE selected as MCO clock + @if STM32F105xC + * @arg @ref RCC_MCO1SOURCE_PLLCLK PLL clock divided by 2 selected as MCO source + * @arg @ref RCC_MCO1SOURCE_PLL2CLK PLL2 clock selected as MCO source + * @arg @ref RCC_MCO1SOURCE_PLL3CLK_DIV2 PLL3 clock divided by 2 selected as MCO source + * @arg @ref RCC_MCO1SOURCE_EXT_HSE XT1 external 3-25 MHz oscillator clock selected as MCO source + * @arg @ref RCC_MCO1SOURCE_PLL3CLK PLL3 clock selected as MCO source + @endif + @if STM32F107xC + * @arg @ref RCC_MCO1SOURCE_PLLCLK PLL clock divided by 2 selected as MCO source + * @arg @ref RCC_MCO1SOURCE_PLL2CLK PLL2 clock selected as MCO source + * @arg @ref RCC_MCO1SOURCE_PLL3CLK_DIV2 PLL3 clock divided by 2 selected as MCO source + * @arg @ref RCC_MCO1SOURCE_EXT_HSE XT1 external 3-25 MHz oscillator clock selected as MCO source + * @arg @ref RCC_MCO1SOURCE_PLL3CLK PLL3 clock selected as MCO source + @endif + * @param RCC_MCODiv specifies the MCO DIV. + * This parameter can be one of the following values: + * @arg @ref RCC_MCODIV_1 no division applied to MCO clock + * @retval None + */ +void HAL_RCC_MCOConfig(uint32_t RCC_MCOx, uint32_t RCC_MCOSource, uint32_t RCC_MCODiv) +{ + GPIO_InitTypeDef gpio = {0}; + + /* Check the parameters */ + assert_param(IS_RCC_MCO(RCC_MCOx)); + assert_param(IS_RCC_MCODIV(RCC_MCODiv)); + assert_param(IS_RCC_MCO1SOURCE(RCC_MCOSource)); + + /* Configure the MCO1 pin in alternate function mode */ + gpio.Mode = GPIO_MODE_AF_PP; + gpio.Speed = GPIO_SPEED_FREQ_HIGH; + gpio.Pull = GPIO_NOPULL; + gpio.Pin = MCO1_PIN; + + /* MCO1 Clock Enable */ + MCO1_CLK_ENABLE(); + + HAL_GPIO_Init(MCO1_GPIO_PORT, &gpio); + + /* Configure the MCO clock source */ + __HAL_RCC_MCO1_CONFIG(RCC_MCOSource, RCC_MCODiv); +} + +/** + * @brief Enables the Clock Security System. + * @note If a failure is detected on the HSE oscillator clock, this oscillator + * is automatically disabled and an interrupt is generated to inform the + * software about the failure (Clock Security System Interrupt, CSSI), + * allowing the MCU to perform rescue operations. The CSSI is linked to + * the Cortex-M3 NMI (Non-Maskable Interrupt) exception vector. + * @retval None + */ +void HAL_RCC_EnableCSS(void) +{ + *(__IO uint32_t *) RCC_CR_CSSON_BB = (uint32_t)ENABLE; +} + +/** + * @brief Disables the Clock Security System. + * @retval None + */ +void HAL_RCC_DisableCSS(void) +{ + *(__IO uint32_t *) RCC_CR_CSSON_BB = (uint32_t)DISABLE; +} + +/** + * @brief Returns the SYSCLK frequency + * @note The system frequency computed by this function is not the real + * frequency in the chip. It is calculated based on the predefined + * constant and the selected clock source: + * @note If SYSCLK source is HSI, function returns values based on HSI_VALUE(*) + * @note If SYSCLK source is HSE, function returns a value based on HSE_VALUE + * divided by PREDIV factor(**) + * @note If SYSCLK source is PLL, function returns a value based on HSE_VALUE + * divided by PREDIV factor(**) or HSI_VALUE(*) multiplied by the PLL factor. + * @note (*) HSI_VALUE is a constant defined in stm32f1xx_hal_conf.h file (default value + * 8 MHz) but the real value may vary depending on the variations + * in voltage and temperature. + * @note (**) HSE_VALUE is a constant defined in stm32f1xx_hal_conf.h file (default value + * 8 MHz), user has to ensure that HSE_VALUE is same as the real + * frequency of the crystal used. Otherwise, this function may + * have wrong result. + * + * @note The result of this function could be not correct when using fractional + * value for HSE crystal. + * + * @note This function can be used by the user application to compute the + * baud-rate for the communication peripherals or configure other parameters. + * + * @note Each time SYSCLK changes, this function must be called to update the + * right SYSCLK value. Otherwise, any configuration based on this function will be incorrect. + * + * @retval SYSCLK frequency + */ +uint32_t HAL_RCC_GetSysClockFreq(void) +{ +#if defined(RCC_CFGR2_PREDIV1SRC) + const uint8_t aPLLMULFactorTable[12] = {0, 0, 4, 5, 6, 7, 8, 9, 0, 0, 0, 13}; + const uint8_t aPredivFactorTable[16] = { 1, 2, 3, 4, 5, 6, 7, 8, 9,10, 11, 12, 13, 14, 15, 16}; +#else + const uint8_t aPLLMULFactorTable[16] = { 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 15, 16, 16}; +#if defined(RCC_CFGR2_PREDIV1) + const uint8_t aPredivFactorTable[16] = { 1, 2, 3, 4, 5, 6, 7, 8, 9,10, 11, 12, 13, 14, 15, 16}; +#else + const uint8_t aPredivFactorTable[2] = { 1, 2}; +#endif /*RCC_CFGR2_PREDIV1*/ + +#endif + uint32_t tmpreg = 0, prediv = 0, pllclk = 0, pllmul = 0; + uint32_t sysclockfreq = 0; +#if defined(RCC_CFGR2_PREDIV1SRC) + uint32_t prediv2 = 0, pll2mul = 0; +#endif /*RCC_CFGR2_PREDIV1SRC*/ + + tmpreg = RCC->CFGR; + + /* Get SYSCLK source -------------------------------------------------------*/ + switch (tmpreg & RCC_CFGR_SWS) + { + case RCC_SYSCLKSOURCE_STATUS_HSE: /* HSE used as system clock */ + { + sysclockfreq = HSE_VALUE; + break; + } + case RCC_SYSCLKSOURCE_STATUS_PLLCLK: /* PLL used as system clock */ + { + pllmul = aPLLMULFactorTable[(uint32_t)(tmpreg & RCC_CFGR_PLLMULL) >> POSITION_VAL(RCC_CFGR_PLLMULL)]; + if ((tmpreg & RCC_CFGR_PLLSRC) != RCC_PLLSOURCE_HSI_DIV2) + { +#if defined(RCC_CFGR2_PREDIV1) + prediv = aPredivFactorTable[(uint32_t)(RCC->CFGR2 & RCC_CFGR2_PREDIV1) >> POSITION_VAL(RCC_CFGR2_PREDIV1)]; +#else + prediv = aPredivFactorTable[(uint32_t)(RCC->CFGR & RCC_CFGR_PLLXTPRE) >> POSITION_VAL(RCC_CFGR_PLLXTPRE)]; +#endif /*RCC_CFGR2_PREDIV1*/ +#if defined(RCC_CFGR2_PREDIV1SRC) + + if(HAL_IS_BIT_SET(RCC->CFGR2, RCC_CFGR2_PREDIV1SRC)) + { + /* PLL2 selected as Prediv1 source */ + /* PLLCLK = PLL2CLK / PREDIV1 * PLLMUL with PLL2CLK = HSE/PREDIV2 * PLL2MUL */ + prediv2 = ((RCC->CFGR2 & RCC_CFGR2_PREDIV2) >> POSITION_VAL(RCC_CFGR2_PREDIV2)) + 1; + pll2mul = ((RCC->CFGR2 & RCC_CFGR2_PLL2MUL) >> POSITION_VAL(RCC_CFGR2_PLL2MUL)) + 2; + pllclk = (uint32_t)((((HSE_VALUE / prediv2) * pll2mul) / prediv) * pllmul); + } + else + { + /* HSE used as PLL clock source : PLLCLK = HSE/PREDIV1 * PLLMUL */ + pllclk = (uint32_t)((HSE_VALUE / prediv) * pllmul); + } + + /* If PLLMUL was set to 13 means that it was to cover the case PLLMUL 6.5 (avoid using float) */ + /* In this case need to divide pllclk by 2 */ + if (pllmul == aPLLMULFactorTable[(uint32_t)(RCC_CFGR_PLLMULL6_5) >> POSITION_VAL(RCC_CFGR_PLLMULL)]) + { + pllclk = pllclk / 2; + } +#else + /* HSE used as PLL clock source : PLLCLK = HSE/PREDIV1 * PLLMUL */ + pllclk = (uint32_t)((HSE_VALUE / prediv) * pllmul); +#endif /*RCC_CFGR2_PREDIV1SRC*/ + } + else + { + /* HSI used as PLL clock source : PLLCLK = HSI/2 * PLLMUL */ + pllclk = (uint32_t)((HSI_VALUE >> 1) * pllmul); + } + sysclockfreq = pllclk; + break; + } + case RCC_SYSCLKSOURCE_STATUS_HSI: /* HSI used as system clock source */ + default: /* HSI used as system clock */ + { + sysclockfreq = HSI_VALUE; + break; + } + } + return sysclockfreq; +} + +/** + * @brief Returns the HCLK frequency + * @note Each time HCLK changes, this function must be called to update the + * right HCLK value. Otherwise, any configuration based on this function will be incorrect. + * + * @note The SystemCoreClock CMSIS variable is used to store System Clock Frequency + * and updated within this function + * @retval HCLK frequency + */ +uint32_t HAL_RCC_GetHCLKFreq(void) +{ + return SystemCoreClock; +} + +/** + * @brief Returns the PCLK1 frequency + * @note Each time PCLK1 changes, this function must be called to update the + * right PCLK1 value. Otherwise, any configuration based on this function will be incorrect. + * @retval PCLK1 frequency + */ +uint32_t HAL_RCC_GetPCLK1Freq(void) +{ + /* Get HCLK source and Compute PCLK1 frequency ---------------------------*/ + return (HAL_RCC_GetHCLKFreq() >> APBPrescTable[(RCC->CFGR & RCC_CFGR_PPRE1) >> RCC_CFGR_PPRE1_BITNUMBER]); +} + +/** + * @brief Returns the PCLK2 frequency + * @note Each time PCLK2 changes, this function must be called to update the + * right PCLK2 value. Otherwise, any configuration based on this function will be incorrect. + * @retval PCLK2 frequency + */ +uint32_t HAL_RCC_GetPCLK2Freq(void) +{ + /* Get HCLK source and Compute PCLK2 frequency ---------------------------*/ + return (HAL_RCC_GetHCLKFreq()>> APBPrescTable[(RCC->CFGR & RCC_CFGR_PPRE2) >> RCC_CFGR_PPRE2_BITNUMBER]); +} + +/** + * @brief Configures the RCC_OscInitStruct according to the internal + * RCC configuration registers. + * @param RCC_OscInitStruct pointer to an RCC_OscInitTypeDef structure that + * will be configured. + * @retval None + */ +void HAL_RCC_GetOscConfig(RCC_OscInitTypeDef *RCC_OscInitStruct) +{ + /* Check the parameters */ + assert_param(RCC_OscInitStruct != NULL); + + /* Set all possible values for the Oscillator type parameter ---------------*/ + RCC_OscInitStruct->OscillatorType = RCC_OSCILLATORTYPE_HSE | RCC_OSCILLATORTYPE_HSI \ + | RCC_OSCILLATORTYPE_LSE | RCC_OSCILLATORTYPE_LSI; + +#if defined(RCC_CFGR2_PREDIV1SRC) + /* Get the Prediv1 source --------------------------------------------------*/ + RCC_OscInitStruct->Prediv1Source = READ_BIT(RCC->CFGR2,RCC_CFGR2_PREDIV1SRC); +#endif /* RCC_CFGR2_PREDIV1SRC */ + + /* Get the HSE configuration -----------------------------------------------*/ + if((RCC->CR &RCC_CR_HSEBYP) == RCC_CR_HSEBYP) + { + RCC_OscInitStruct->HSEState = RCC_HSE_BYPASS; + } + else if((RCC->CR &RCC_CR_HSEON) == RCC_CR_HSEON) + { + RCC_OscInitStruct->HSEState = RCC_HSE_ON; + } + else + { + RCC_OscInitStruct->HSEState = RCC_HSE_OFF; + } + RCC_OscInitStruct->HSEPredivValue = __HAL_RCC_HSE_GET_PREDIV(); + + /* Get the HSI configuration -----------------------------------------------*/ + if((RCC->CR &RCC_CR_HSION) == RCC_CR_HSION) + { + RCC_OscInitStruct->HSIState = RCC_HSI_ON; + } + else + { + RCC_OscInitStruct->HSIState = RCC_HSI_OFF; + } + + RCC_OscInitStruct->HSICalibrationValue = (uint32_t)((RCC->CR & RCC_CR_HSITRIM) >> POSITION_VAL(RCC_CR_HSITRIM)); + + /* Get the LSE configuration -----------------------------------------------*/ + if((RCC->BDCR &RCC_BDCR_LSEBYP) == RCC_BDCR_LSEBYP) + { + RCC_OscInitStruct->LSEState = RCC_LSE_BYPASS; + } + else if((RCC->BDCR &RCC_BDCR_LSEON) == RCC_BDCR_LSEON) + { + RCC_OscInitStruct->LSEState = RCC_LSE_ON; + } + else + { + RCC_OscInitStruct->LSEState = RCC_LSE_OFF; + } + + /* Get the LSI configuration -----------------------------------------------*/ + if((RCC->CSR &RCC_CSR_LSION) == RCC_CSR_LSION) + { + RCC_OscInitStruct->LSIState = RCC_LSI_ON; + } + else + { + RCC_OscInitStruct->LSIState = RCC_LSI_OFF; + } + + + /* Get the PLL configuration -----------------------------------------------*/ + if((RCC->CR &RCC_CR_PLLON) == RCC_CR_PLLON) + { + RCC_OscInitStruct->PLL.PLLState = RCC_PLL_ON; + } + else + { + RCC_OscInitStruct->PLL.PLLState = RCC_PLL_OFF; + } + RCC_OscInitStruct->PLL.PLLSource = (uint32_t)(RCC->CFGR & RCC_CFGR_PLLSRC); + RCC_OscInitStruct->PLL.PLLMUL = (uint32_t)(RCC->CFGR & RCC_CFGR_PLLMULL); +#if defined(RCC_CR_PLL2ON) + /* Get the PLL2 configuration -----------------------------------------------*/ + if((RCC->CR &RCC_CR_PLL2ON) == RCC_CR_PLL2ON) + { + RCC_OscInitStruct->PLL2.PLL2State = RCC_PLL2_ON; + } + else + { + RCC_OscInitStruct->PLL2.PLL2State = RCC_PLL2_OFF; + } + RCC_OscInitStruct->PLL2.HSEPrediv2Value = __HAL_RCC_HSE_GET_PREDIV2(); + RCC_OscInitStruct->PLL2.PLL2MUL = (uint32_t)(RCC->CFGR2 & RCC_CFGR2_PLL2MUL); +#endif /* RCC_CR_PLL2ON */ +} + +/** + * @brief Get the RCC_ClkInitStruct according to the internal + * RCC configuration registers. + * @param RCC_ClkInitStruct pointer to an RCC_ClkInitTypeDef structure that + * contains the current clock configuration. + * @param pFLatency Pointer on the Flash Latency. + * @retval None + */ +void HAL_RCC_GetClockConfig(RCC_ClkInitTypeDef *RCC_ClkInitStruct, uint32_t *pFLatency) +{ + /* Check the parameters */ + assert_param(RCC_ClkInitStruct != NULL); + assert_param(pFLatency != NULL); + + /* Set all possible values for the Clock type parameter --------------------*/ + RCC_ClkInitStruct->ClockType = RCC_CLOCKTYPE_SYSCLK | RCC_CLOCKTYPE_HCLK | RCC_CLOCKTYPE_PCLK1 | RCC_CLOCKTYPE_PCLK2; + + /* Get the SYSCLK configuration --------------------------------------------*/ + RCC_ClkInitStruct->SYSCLKSource = (uint32_t)(RCC->CFGR & RCC_CFGR_SW); + + /* Get the HCLK configuration ----------------------------------------------*/ + RCC_ClkInitStruct->AHBCLKDivider = (uint32_t)(RCC->CFGR & RCC_CFGR_HPRE); + + /* Get the APB1 configuration ----------------------------------------------*/ + RCC_ClkInitStruct->APB1CLKDivider = (uint32_t)(RCC->CFGR & RCC_CFGR_PPRE1); + + /* Get the APB2 configuration ----------------------------------------------*/ + RCC_ClkInitStruct->APB2CLKDivider = (uint32_t)((RCC->CFGR & RCC_CFGR_PPRE2) >> 3); + +#if defined(FLASH_ACR_LATENCY) + /* Get the Flash Wait State (Latency) configuration ------------------------*/ + *pFLatency = (uint32_t)(FLASH->ACR & FLASH_ACR_LATENCY); +#else + /* For VALUE lines devices, only LATENCY_0 can be set*/ + *pFLatency = (uint32_t)FLASH_LATENCY_0; +#endif +} + +/** + * @brief This function handles the RCC CSS interrupt request. + * @note This API should be called under the NMI_Handler(). + * @retval None + */ +void HAL_RCC_NMI_IRQHandler(void) +{ + /* Check RCC CSSF flag */ + if(__HAL_RCC_GET_IT(RCC_IT_CSS)) + { + /* RCC Clock Security System interrupt user callback */ + HAL_RCC_CSSCallback(); + + /* Clear RCC CSS pending bit */ + __HAL_RCC_CLEAR_IT(RCC_IT_CSS); + } +} + +/** + * @brief RCC Clock Security System interrupt callback + * @retval none + */ +__weak void HAL_RCC_CSSCallback(void) +{ + /* NOTE : This function Should not be modified, when the callback is needed, + the HAL_RCC_CSSCallback could be implemented in the user file + */ +} + +/** + * @} + */ + +/** + * @} + */ + +#endif /* HAL_RCC_MODULE_ENABLED */ +/** + * @} + */ + +/** + * @} + */ + +/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/ -- cgit v1.2.3