/** * Copyright (c) 2012 - 2018, Nordic Semiconductor ASA * * All rights reserved. * * Redistribution and use in source and binary forms, with or without modification, * are permitted provided that the following conditions are met: * * 1. Redistributions of source code must retain the above copyright notice, this * list of conditions and the following disclaimer. * * 2. Redistributions in binary form, except as embedded into a Nordic * Semiconductor ASA integrated circuit in a product or a software update for * such product, must reproduce the above copyright notice, this list of * conditions and the following disclaimer in the documentation and/or other * materials provided with the distribution. * * 3. Neither the name of Nordic Semiconductor ASA nor the names of its * contributors may be used to endorse or promote products derived from this * software without specific prior written permission. * * 4. This software, with or without modification, must only be used with a * Nordic Semiconductor ASA integrated circuit. * * 5. Any software provided in binary form under this license must not be reverse * engineered, decompiled, modified and/or disassembled. * * THIS SOFTWARE IS PROVIDED BY NORDIC SEMICONDUCTOR ASA "AS IS" AND ANY EXPRESS * OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES * OF MERCHANTABILITY, NONINFRINGEMENT, AND FITNESS FOR A PARTICULAR PURPOSE ARE * DISCLAIMED. IN NO EVENT SHALL NORDIC SEMICONDUCTOR ASA OR CONTRIBUTORS BE * LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR * CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE * GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT * OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. * */ /** @defgroup dtm_standalone main.c @{ @ingroup ble_sdk_app_dtm_serial @brief Stand-alone DTM application for UART interface. */ #include #include #include "nrf.h" #include "ble_dtm.h" #include "nrf_gpio.h" #include "dtm_uart.h" #include "nrf_error.h" #include "app_util.h" #include "nrf_drv_uart.h" #include "nrf_peripherals.h" #include "app_util_platform.h" //Configuration parameters. #define BITRATE UART_BAUDRATE_BAUDRATE_Baud57600 /**< Serial bitrate on the UART */ //@note: The BLE DTM 2-wire UART standard specifies 8 data bits, 1 stop bit, no flow control. //These parameters are not configurable in the BLE standard. /**@details Maximum iterations needed in the main loop between stop bit 1st byte and start bit 2nd * byte. DTM standard allows 5000us delay between stop bit 1st byte and start bit 2nd byte. * As the time is only known when a byte is received, then the time between between stop bit 1st * byte and stop bit 2nd byte becomes: * 5000us + transmission time of 2nd byte. * * Byte transmission time is (Baud rate of 19200): * 10bits * 1/19200 = approx. 520 us/byte (8 data bits + start & stop bit). * * Loop time on polling UART register for received byte is defined in ble_dtm.c as: * UART_POLL_CYCLE = 260 us * * The max time between two bytes thus becomes (loop time: 260us / iteration): * (5000us + 520us) / 260us / iteration = 21.2 iterations. * * This is rounded down to 21. * * @note If UART bit rate is changed, this value should be recalculated as well. */ static uint32_t m_baud_rates[] = {[UART_BAUD_RATE_1200] = NRF_UART_BAUDRATE_1200, [UART_BAUD_RATE_2400] = NRF_UART_BAUDRATE_2400, [UART_BAUD_RATE_4800] = NRF_UART_BAUDRATE_4800, [UART_BAUD_RATE_9600] = NRF_UART_BAUDRATE_9600, [UART_BAUD_RATE_14400] = NRF_UART_BAUDRATE_14400, [UART_BAUD_RATE_19200] = NRF_UART_BAUDRATE_19200, [UART_BAUD_RATE_28800] = NRF_UART_BAUDRATE_28800, [UART_BAUD_RATE_38400] = NRF_UART_BAUDRATE_38400, [UART_BAUD_RATE_57600] = NRF_UART_BAUDRATE_57600, [UART_BAUD_RATE_76800] = NRF_UART_BAUDRATE_76800, [UART_BAUD_RATE_115200] = NRF_UART_BAUDRATE_115200 }; static uint32_t m_iteration[] = {[UART_BAUD_RATE_1200] = 51, [UART_BAUD_RATE_2400] = 35, [UART_BAUD_RATE_4800] = 27, [UART_BAUD_RATE_9600] = 23, [UART_BAUD_RATE_14400] = 21, [UART_BAUD_RATE_19200] = 21, [UART_BAUD_RATE_28800] = 20, [UART_BAUD_RATE_38400] = 20, [UART_BAUD_RATE_57600] = 19, [UART_BAUD_RATE_76800] = 19, [UART_BAUD_RATE_115200] = 19, }; static uint32_t m_iterations_next_byte_max = 51; static nrf_drv_uart_t m_dtm_uart_driver = NRF_DRV_UART_INSTANCE(0); /**@brief Function for UART initialization. */ static uint32_t uart_init(app_uart_stream_comm_params_t * p_comm_params) { if (p_comm_params->baud_rate > UART_BAUD_RATE_115200) { return NRF_ERROR_INVALID_PARAM; } nrf_drv_uart_config_t config = NRF_DRV_UART_DEFAULT_CONFIG; config.pselrxd = p_comm_params->rx_pin_no; config.pseltxd = p_comm_params->tx_pin_no; config.baudrate = (nrf_uart_baudrate_t) m_baud_rates[p_comm_params->baud_rate]; config.hwfc = NRF_UART_HWFC_DISABLED; config.parity = NRF_UART_PARITY_EXCLUDED; #ifdef UART_PRESENT //Current implementation of DTM requires legacy UART features and // it will not work on nrf52810. config.use_easy_dma = false; #endif nrf_drv_uart_uninit(&m_dtm_uart_driver); uint32_t err_code = nrf_drv_uart_init(&m_dtm_uart_driver, &config, NULL); if (err_code != NRF_SUCCESS) { return err_code; } nrf_drv_uart_rx_enable(&m_dtm_uart_driver); m_iterations_next_byte_max = m_iteration[p_comm_params->baud_rate]; return NRF_SUCCESS; } /**@brief Function for splitting UART command bit fields into separate command parameters for the DTM library. * * @param[in] command The packed UART command. * @return result status from dtmlib. */ static uint32_t dtm_cmd_put(uint16_t command) { dtm_cmd_t command_code = (command >> 14) & 0x03; dtm_freq_t freq = (command >> 8) & 0x3F; uint32_t length = (command >> 2) & 0x3F; dtm_pkt_type_t payload = command & 0x03; //Check for Vendor Specific payload. if (payload == 0x03) { /* Note that in a HCI adaption layer, as well as in the DTM PDU format, the value 0x03 is a distinct bit pattern (PRBS15). Even though BLE does not support PRBS15, this implementation re-maps 0x03 to DTM_PKT_VENDORSPECIFIC, to avoid the risk of confusion, should the code be extended to greater coverage. */ payload = DTM_PKT_VENDORSPECIFIC; } return dtm_cmd(command_code, freq, length, payload); } /**@brief Function for application main entry. * * @details This function serves as an adaptation layer between a 2-wire UART interface and the * dtmlib. After initialization, DTM commands submitted through the UART are forwarded to * dtmlib and events (i.e. results from the command) is reported back through the UART. */ uint32_t dtm_start(app_uart_stream_comm_params_t uart_comm_params) { uint32_t current_time; uint32_t dtm_error_code; uint32_t msb_time = 0; //Time when MSB of the DTM command was read. Used to catch stray bytes from "misbehaving" testers. bool is_msb_read = false; //True when MSB of the DTM command has been read and the application is waiting for LSB. uint16_t dtm_cmd_from_uart = 0; //Packed command containing command_code:freqency:length:payload in 2:6:6:2 bits. uint8_t rx_byte; //Last byte read from UART. dtm_event_t result; //Result of a DTM operation. uint32_t err_code; err_code = uart_init(&uart_comm_params); if (err_code != NRF_SUCCESS) { return err_code; } dtm_error_code = dtm_init(); if (dtm_error_code != DTM_SUCCESS) { //If DTM cannot be correctly initialized, then we just return. return NRF_ERROR_INTERNAL; } for (;; ) { //Will return every timeout, 625 us. current_time = dtm_wait(); if (NRF_SUCCESS != nrf_drv_uart_rx(&m_dtm_uart_driver, &rx_byte,1)) { return NRF_ERROR_INTERNAL; } if (!is_msb_read) { //This is first byte of two-byte command. is_msb_read = true; dtm_cmd_from_uart = ((dtm_cmd_t)rx_byte) << 8; msb_time = current_time; //Go back and wait for 2nd byte of command word. continue; } //This is the second byte read; combine it with the first and process command if (current_time > (msb_time + m_iterations_next_byte_max)) { //More than ~5mS after msb: Drop old byte, take the new byte as MSB. //The variable is_msb_read will remains true. //Go back and wait for 2nd byte of the command word. dtm_cmd_from_uart = ((dtm_cmd_t)rx_byte) << 8; msb_time = current_time; continue; } //2-byte UART command received. is_msb_read = false; dtm_cmd_from_uart |= (dtm_cmd_t)rx_byte; if (dtm_cmd_put(dtm_cmd_from_uart) != DTM_SUCCESS) { //Extended error handling may be put here. //Default behavior is to return the event on the UART (see below); //the event report will reflect any lack of success. } //Retrieve result of the operation. This implementation will busy-loop //for the duration of the byte transmissions on the UART. if (dtm_event_get(&result)) { //Report command status on the UART. uint8_t tx_byte = (result >> 8) & 0xFF; //Transmit MSB of the result. (void)nrf_drv_uart_tx(&m_dtm_uart_driver, &tx_byte, 1); //Transmit LSB of the result. tx_byte = result & 0xFF; (void)nrf_drv_uart_tx(&m_dtm_uart_driver, &tx_byte, 1); } } } /// @}