diff options
Diffstat (limited to 'doc/openocd.texi')
| -rw-r--r-- | doc/openocd.texi | 86 |
1 files changed, 0 insertions, 86 deletions
diff --git a/doc/openocd.texi b/doc/openocd.texi index 8e1d1a8f..86f5748f 100644 --- a/doc/openocd.texi +++ b/doc/openocd.texi @@ -81,7 +81,6 @@ Free Documentation License''. * TFTP:: TFTP * GDB and OpenOCD:: Using GDB and OpenOCD * Tcl Scripting API:: Tcl Scripting API -* Upgrading:: Deprecated/Removed Commands * FAQ:: Frequently Asked Questions * Tcl Crash Course:: Tcl Crash Course * License:: GNU Free Documentation License @@ -6507,91 +6506,6 @@ We should add support for a variable like Tcl variable is jim, not real tcl). @end quotation -@node Upgrading -@chapter Deprecated/Removed Commands -@cindex Deprecated/Removed Commands -Certain OpenOCD commands have been deprecated or -removed during the various revisions. - -Upgrade your scripts as soon as possible. -These descriptions for old commands may be removed -a year after the command itself was removed. -This means that in January 2010 this chapter may -become much shorter. - -@itemize @bullet -@item @b{arm7_9 fast_writes} -@cindex arm7_9 fast_writes -@*Use @command{arm7_9 fast_memory_access} instead. -@xref{arm7_9 fast_memory_access}. -@item @b{endstate} -@cindex endstate -@*An buggy old command that would not really work since background polling would wipe out the global endstate -@item @b{arm7_9 force_hw_bkpts} -@*Use @command{gdb_breakpoint_override} instead. Note that GDB will use hardware breakpoints -for flash if the GDB memory map has been set up(default when flash is declared in -target configuration). @xref{gdb_breakpoint_override}. -@item @b{arm7_9 sw_bkpts} -@*On by default. @xref{gdb_breakpoint_override}. -@item @b{daemon_startup} -@*this config option has been removed, simply adding @option{init} and @option{reset halt} to -the end of your config script will give the same behaviour as using @option{daemon_startup reset} -and @option{target cortex_m3 little reset_halt 0}. -@item @b{dump_binary} -@*use @option{dump_image} command with same args. @xref{dump_image}. -@item @b{flash erase} -@*use @option{flash erase_sector} command with same args. @xref{flash erase_sector}. -@item @b{flash write} -@*use @option{flash write_bank} command with same args. @xref{flash write_bank}. -@item @b{flash write_binary} -@*use @option{flash write_bank} command with same args. @xref{flash write_bank}. -@item @b{flash auto_erase} -@*use @option{flash write_image} command passing @option{erase} as the first parameter. @xref{flash write_image}. - -@item @b{jtag_device} -@*use the @command{jtag newtap} command, converting from positional syntax -to named prefixes, and naming the TAP. -@xref{jtag newtap}. -Note that if you try to use the old command, a message will tell you the -right new command to use; and that the fourth parameter in the old syntax -was never actually used. -@example -OLD: jtag_device 8 0x01 0xe3 0xfe -NEW: jtag newtap CHIPNAME TAPNAME \ - -irlen 8 -ircapture 0x01 -irmask 0xe3 -@end example - -@item @b{jtag_speed} value -@*@xref{JTAG Speed}. -Usually, a value of zero means maximum -speed. The actual effect of this option depends on the JTAG interface used. -@itemize @minus -@item wiggler: maximum speed / @var{number} -@item ft2232: 6MHz / (@var{number}+1) -@item amt jtagaccel: 8 / 2**@var{number} -@item jlink: maximum speed in kHz (0-12000), 0 will use RTCK -@item rlink: 24MHz / @var{number}, but only for certain values of @var{number} -@comment end speed list. -@end itemize - -@item @b{load_binary} -@*use @option{load_image} command with same args. @xref{load_image}. -@item @b{run_and_halt_time} -@*This command has been removed for simpler reset behaviour, it can be simulated with the -following commands: -@smallexample -reset run -sleep 100 -halt -@end smallexample -@item @b{target} <@var{type}> <@var{endian}> <@var{jtag-position}> -@*use the create subcommand of @option{target}. -@item @b{target_script} <@var{target#}> <@var{eventname}> <@var{scriptname}> -@*use <@var{target_name}> configure -event <@var{eventname}> "script <@var{scriptname}>" -@item @b{working_area} -@*use the @option{configure} subcommand of @option{target} to set the work-area-virt, work-area-phy, work-area-size, and work-area-backup properties of the target. -@end itemize - @node FAQ @chapter FAQ @cindex faq |