diff options
Diffstat (limited to 'src/target/board/zy1000.cfg')
| -rw-r--r-- | src/target/board/zy1000.cfg | 110 |
1 files changed, 0 insertions, 110 deletions
diff --git a/src/target/board/zy1000.cfg b/src/target/board/zy1000.cfg deleted file mode 100644 index d8bb4650..00000000 --- a/src/target/board/zy1000.cfg +++ /dev/null @@ -1,110 +0,0 @@ -#Script for ZY1000 - -#Atmel ties SRST & TRST together, at which point it makes -#no sense to use TRST, but use TMS instead. -# -#The annoying thing with tying SRST & TRST together is that -#there is no way to halt the CPU *before and during* the -#SRST reset, which means that the CPU will run a number -#of cycles before it can be halted(as much as milliseconds). -reset_config srst_only srst_pulls_trst - - -if { [info exists CHIPNAME] } { - set _CHIPNAME $CHIPNAME -} else { - set _CHIPNAME zy1000 -} - -if { [info exists ENDIAN] } { - set _ENDIAN $ENDIAN -} else { - set _ENDIAN little -} - - -#jtag scan chain -if { [info exists CPUTAPID ] } { - set _CPUTAPID $CPUTAPID -} else { - set _CPUTAPID 0x1f0f0f0f -} -jtag newtap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_CPUTAPID - -set _TARGETNAME [format "%s.cpu" $_CHIPNAME] -target create $_TARGETNAME arm7tdmi -endian $_ENDIAN -chain-position $_TARGETNAME -variant arm7tdmi-s_r4 - -# at CPU CLK <32kHz this must be disabled -arm7_9 fast_memory_access enable -arm7_9 dcc_downloads enable - -flash bank ecosflash 0x01000000 0x200000 2 2 0 ecos/at91eb40a.elf -$_TARGETNAME configure -event reset-init { - # Set up chip selects & timings - mww 0xFFE00000 0x0100273D - mww 0xFFE00004 0x08002125 - mww 0xFFEe0008 0x02002125 - mww 0xFFE0000c 0x03002125 - mww 0xFFE00010 0x40000000 - mww 0xFFE00014 0x50000000 - mww 0xFFE00018 0x60000000 - mww 0xFFE0001c 0x70000000 - mww 0xFFE00020 0x00000001 - mww 0xFFE00024 0x00000000 - - # remap - mww 0xFFFFF124 0xFFFFFFFF - mww 0xffff0010 0x100 - mww 0xffff0034 0x100 - - #disable 16x5x UART interrupts - mww 0x08020004 0 -} - -# required for usable performance. Used for lots of -# other things than flash programming. -$_TARGETNAME configure -work-area-virt 0 -work-area-phys 0x00020000 -work-area-size 0x20000 -work-area-backup 0 - -jtag_khz 16000 - - -proc production_info {} { - return "Serial number is official MAC number. Format XXXXXXXXXXXX" -} - -# There is no return value from this procedure. If it is -# successful it does not throw an exception -# -# Progress messages are output via puts -proc production {firmwarefile serialnumber} { - if {[string length $serialnumber]!=12} { - puts "Invalid serial number" - return - } - - puts "Power cycling target" - power off - sleep 3000 - power on - sleep 1000 - reset init - flash write_image erase $firmwarefile 0x1000000 bin - verify_image $firmwarefile 0x1000000 bin - - # Big endian... weee!!!! - puts "Setting MAC number to $serialnumber" - flash fillw [expr 0x1030000-0x8] "0x[string range $serialnumber 2 3][string range $serialnumber 0 1]0000" 1 - flash fillw [expr 0x1030000-0x4] "0x[string range $serialnumber 10 11][string range $serialnumber 8 9][string range $serialnumber 6 7][string range $serialnumber 4 5]" 1 - puts "Production successful" -} - - -proc production_test {} { - power on - sleep 1000 - target_request debugmsgs enable - reset run - sleep 25000 - target_request debugmsgs disable - return "See IP address above..." -} |