diff options
Diffstat (limited to 'src')
| -rw-r--r-- | src/target/arm_adi_v5.c | 28 |
1 files changed, 27 insertions, 1 deletions
diff --git a/src/target/arm_adi_v5.c b/src/target/arm_adi_v5.c index e490f2e5..1a864589 100644 --- a/src/target/arm_adi_v5.c +++ b/src/target/arm_adi_v5.c @@ -88,7 +88,24 @@ static uint32_t max_tar_block_size(uint32_t tar_autoincr_block, uint32_t address * * ***************************************************************************/ -/* Scan out and in from target ordered uint8_t buffers */ +/** + * Scan DPACC or APACC using target ordered uint8_t buffers. No endianness + * conversions are performed. See section 4.4.3 of the ADIv5 spec, which + * discusses operations which access these registers. + * + * Note that only one scan is performed. If RnW is set, a separate scan + * will be needed to collect the data which was read; the "invalue" collects + * the posted result of a preceding operation, not the current one. + * + * @param swjdp the DAP + * @param instr JTAG_DP_APACC (AP access) or JTAG_DP_DPACC (DP access) + * @param reg_addr two significant bits; A[3:2]; for APACC access, the + * SELECT register has more addressing bits. + * @param RnW false iff outvalue will be written to the DP or AP + * @param outvalue points to a 32-bit (little-endian) integer + * @param invalue NULL, or points to a 32-bit (little-endian) integer + * @param ack points to where the three bit JTAG_ACK_* code will be stored + */ static int adi_jtag_dp_scan(struct swjdp_common *swjdp, uint8_t instr, uint8_t reg_addr, uint8_t RnW, uint8_t *outvalue, uint8_t *invalue, uint8_t *ack) @@ -104,6 +121,7 @@ static int adi_jtag_dp_scan(struct swjdp_common *swjdp, /* REVISIT these TCK cycles should be *AFTER* updating APACC, since * they provide more time for the (MEM) AP to complete the read ... + * See "Minimum Response Time" for JTAG-DP, in the ADIv5 spec. */ if ((instr == JTAG_DP_APACC) && ((reg_addr == AP_REG_DRW) @@ -111,12 +129,20 @@ static int adi_jtag_dp_scan(struct swjdp_common *swjdp, && (swjdp->memaccess_tck != 0)) jtag_add_runtest(swjdp->memaccess_tck, jtag_set_end_state(TAP_IDLE)); + /* Scan out a read or write operation using some DP or AP register. + * For APACC access with any sticky error flag set, this is discarded. + */ fields[0].tap = jtag_info->tap; fields[0].num_bits = 3; buf_set_u32(&out_addr_buf, 0, 3, ((reg_addr >> 1) & 0x6) | (RnW & 0x1)); fields[0].out_value = &out_addr_buf; fields[0].in_value = ack; + /* NOTE: if we receive JTAG_ACK_WAIT, the previous operation did not + * complete; data we write is discarded, data we read is unpredictable. + * When overrun detect is active, STICKYORUN is set. + */ + fields[1].tap = jtag_info->tap; fields[1].num_bits = 32; fields[1].out_value = outvalue; |