diff options
Diffstat (limited to 'src')
| -rw-r--r-- | src/target/target/lpc2148.cfg | 46 |
1 files changed, 24 insertions, 22 deletions
diff --git a/src/target/target/lpc2148.cfg b/src/target/target/lpc2148.cfg index 7b701ab6..a728195c 100644 --- a/src/target/target/lpc2148.cfg +++ b/src/target/target/lpc2148.cfg @@ -1,49 +1,51 @@ - if { [info exists CHIPNAME] } { - set _CHIPNAME $CHIPNAME -} else { - set _CHIPNAME lpc2148 + set _CHIPNAME $CHIPNAME +} else { + set _CHIPNAME lpc2148 } -if { [info exists ENDIAN] } { - set _ENDIAN $ENDIAN -} else { - set _ENDIAN little +if { [info exists ENDIAN] } { + set _ENDIAN $ENDIAN +} else { + set _ENDIAN little } if { [info exists CPUTAPID ] } { set _CPUTAPID $CPUTAPID } else { - # force an error till we get a good number - set _CPUTAPID 0xffffffff + set _CPUTAPID 0x4f1f0f0f } -#delays on reset lines jtag_nsrst_delay 200 jtag_ntrst_delay 200 -# NOTE!!! LPCs need reset pulled while RTCK is low. 0 to activate +# NOTE!!! LPCs need reset pulled while RTCK is low. 0 to activate # JTAG, power-on reset is not enough, i.e. you need to perform a -# reset before being able to talk to the LPC2148, attach is not -# possible. +# reset before being able to talk to the LPC2148, attach is not possible. -#use combined on interfaces or targets that can't set TRST/SRST separately reset_config trst_and_srst srst_pulls_trst -#jtag scan chain jtag newtap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_CPUTAPID set _TARGETNAME [format "%s.cpu" $_CHIPNAME] + target create $_TARGETNAME arm7tdmi -endian $_ENDIAN -chain-position $_TARGETNAME -variant arm7tdmi-s_r4 + $_TARGETNAME configure -work-area-virt 0 -work-area-phys 0x40000000 -work-area-size 0x4000 -work-area-backup 0 + $_TARGETNAME configure -event reset-init { - # Force target into ARM state + # Force target into ARM state. soft_reset_halt - #do not remap 0x0000-0x0020 to anything but the flash - mwb 0xE01FC040 0x01 - -} + # Do not remap 0x0000-0x0020 to anything but the flash (i.e. select + # "User Flash Mode" where interrupt vectors are _not_ remapped, + # and reside in flash instead). + # + # See section 7.1 on page 32 ("Memory Mapping control register") in + # "UM10139: Volume 1: LPC214x User Manual", Rev. 02 -- 25 July 2006. + # http://www.standardics.nxp.com/support/documents/microcontrollers/pdf/user.manual.lpc2141.lpc2142.lpc2144.lpc2146.lpc2148.pdf + mwb 0xE01FC040 0x01 +} -#flash bank lpc2000 <base> <size> 0 0 <target#> <variant> +# flash bank lpc2000 <base> <size> 0 0 <target#> <variant> <clock> [calc_checksum] flash bank lpc2000 0x0 0x7d000 0 0 0 lpc2000_v2 14765 |