diff options
Diffstat (limited to 'tcl')
44 files changed, 47 insertions, 45 deletions
diff --git a/tcl/board/at91sam9g20-ek.cfg b/tcl/board/at91sam9g20-ek.cfg index 00ab7faf..6e8a1934 100644 --- a/tcl/board/at91sam9g20-ek.cfg +++ b/tcl/board/at91sam9g20-ek.cfg @@ -41,8 +41,8 @@ target create $_TARGETNAME arm926ejs -endian $_ENDIAN -chain-position $_TARGETNA # AT91SAM9G20 has two SRAM areas, one starting at 0x00200000 and the other starting at 0x00300000. # Both areas are 16 kB long. -$_TARGETNAME configure -work-area-virt 0 -work-area-phys 0x00200000 -work-area-size 0x4000 -work-area-backup 1 -$_TARGETNAME configure -work-area-virt 0 -work-area-phys 0x00300000 -work-area-size 0x4000 -work-area-backup 1 +#$_TARGETNAME configure -work-area-phys 0x00200000 -work-area-size 0x4000 -work-area-backup 1 +$_TARGETNAME configure -work-area-phys 0x00300000 -work-area-size 0x4000 -work-area-backup 1 # If you don't want to execute built-in boot rom code (and there are good reasons at times not to do that) in the # AT91SAM9 family, the microcontroller is a lump on a log without initialization. Because this family has diff --git a/tcl/board/digi_connectcore_wi-9c.cfg b/tcl/board/digi_connectcore_wi-9c.cfg index 58f12a68..e6d17bdd 100644 --- a/tcl/board/digi_connectcore_wi-9c.cfg +++ b/tcl/board/digi_connectcore_wi-9c.cfg @@ -114,7 +114,7 @@ $_TARGETNAME configure -event reset-init { reg cpsr 0xd3 } -$_TARGETNAME configure -work-area-virt 0 -work-area-phys 0x00000000 -work-area-size 0x1000 -work-area-backup 1 +$_TARGETNAME configure -work-area-phys 0x00000000 -work-area-size 0x1000 -work-area-backup 1 ##################### # Flash configuration diff --git a/tcl/board/hitex_str9-comstick.cfg b/tcl/board/hitex_str9-comstick.cfg index 25ff784d..e7b79616 100644 --- a/tcl/board/hitex_str9-comstick.cfg +++ b/tcl/board/hitex_str9-comstick.cfg @@ -65,7 +65,7 @@ $_TARGETNAME configure -event reset-init { flash protect 0 0 7 off } -$_TARGETNAME configure -work-area-virt 0 -work-area-phys 0x50000000 -work-area-size 16384 -work-area-backup 0 +$_TARGETNAME configure -work-area-phys 0x50000000 -work-area-size 16384 -work-area-backup 0 #flash bank <driver> <base> <size> <chip_width> <bus_width> flash bank str9x 0x00000000 0x00080000 0 0 0 diff --git a/tcl/board/linksys_nslu2.cfg b/tcl/board/linksys_nslu2.cfg index 52984107..e605fc19 100644 --- a/tcl/board/linksys_nslu2.cfg +++ b/tcl/board/linksys_nslu2.cfg @@ -4,5 +4,5 @@ source [find target/ixp42x.cfg] # The _TARGETNAME is set by the above. -$_TARGETNAME configure -work-area-virt 0 -work-area-phys 0x00020000 -work-area-size 0x10000 -work-area-backup 0 +$_TARGETNAME configure -work-area-phys 0x00020000 -work-area-size 0x10000 -work-area-backup 0 diff --git a/tcl/board/mini2440.cfg b/tcl/board/mini2440.cfg index 90acafa0..d17b1076 100644 --- a/tcl/board/mini2440.cfg +++ b/tcl/board/mini2440.cfg @@ -104,7 +104,7 @@ jtag newtap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0x0f -expected-id $_C set _TARGETNAME [format "%s.cpu" $_CHIPNAME] target create $_TARGETNAME arm920t -endian $_ENDIAN -chain-position $_TARGETNAME -variant arm920t -$_TARGETNAME configure -work-area-virt 0 -work-area-phys 0x40000000 -work-area-size 0x4000 -work-area-backup 1 +$_TARGETNAME configure -work-area-phys 0x40000000 -work-area-size 0x4000 -work-area-backup 1 #reset configuration jtag_nsrst_delay 100 diff --git a/tcl/board/pxa255_sst.cfg b/tcl/board/pxa255_sst.cfg index d9f6187b..8bc691ba 100644 --- a/tcl/board/pxa255_sst.cfg +++ b/tcl/board/pxa255_sst.cfg @@ -10,7 +10,7 @@ source [find target/pxa255.cfg] # Target name is set by above -$_TARGETNAME configure -work-area-virt 0 -work-area-phys 0x4000000 -work-area-size 0x4000 -work-area-backup 0 +$_TARGETNAME configure -work-area-phys 0x4000000 -work-area-size 0x4000 -work-area-backup 0 # flash bank <driver> <base> <size> <chip_width> <bus_width> <target> [options] flash bank cfi 0x00000000 0x80000 2 2 $_TARGETNAME jedec_probe diff --git a/tcl/board/str910-eval.cfg b/tcl/board/str910-eval.cfg index e98c1c74..fa872a9b 100644 --- a/tcl/board/str910-eval.cfg +++ b/tcl/board/str910-eval.cfg @@ -39,7 +39,7 @@ jtag newtap $_CHIPNAME bs -irlen 5 -ircapture 0x1 -irmask 0x1 -expected-id $_ set _TARGETNAME [format "%s.cpu" $_CHIPNAME] target create $_TARGETNAME arm966e -endian $_ENDIAN -chain-position $_TARGETNAME -variant arm966e -$_TARGETNAME configure -work-area-phys 0x50000000 -work-area-virt 0x50000000 -work-area-size 16384 -work-area-backup 1 +$_TARGETNAME configure -work-area-phys 0x50000000 -work-area-size 16384 -work-area-backup 1 $_TARGETNAME configure -event reset-init { # We can increase speed now that we know the target is halted. diff --git a/tcl/board/zy1000.cfg b/tcl/board/zy1000.cfg index 2e13ecbb..54bb7bb7 100644 --- a/tcl/board/zy1000.cfg +++ b/tcl/board/zy1000.cfg @@ -63,7 +63,7 @@ $_TARGETNAME configure -event reset-init { # required for usable performance. Used for lots of # other things than flash programming. -$_TARGETNAME configure -work-area-virt 0 -work-area-phys 0x00020000 -work-area-size 0x20000 -work-area-backup 0 +$_TARGETNAME configure -work-area-phys 0x00020000 -work-area-size 0x20000 -work-area-backup 0 jtag_khz 16000 diff --git a/tcl/target/at91eb40a.cfg b/tcl/target/at91eb40a.cfg index 064a3b56..8b3a9ec1 100644 --- a/tcl/target/at91eb40a.cfg +++ b/tcl/target/at91eb40a.cfg @@ -46,7 +46,7 @@ flash bank ecosflash 0x01000000 0x200000 2 2 0 ecos/at91eb40a.elf # required for usable performance. Used for lots of # other things than flash programming. -$_TARGETNAME configure -work-area-virt 0 -work-area-phys 0x00030000 -work-area-size 0x10000 -work-area-backup 0 +$_TARGETNAME configure -work-area-phys 0x00030000 -work-area-size 0x10000 -work-area-backup 0 $_TARGETNAME configure -event reset-init { puts "Running reset init script for AT91EB40A" diff --git a/tcl/target/at91r40008.cfg b/tcl/target/at91r40008.cfg index eb6cabaa..e8710f7f 100644 --- a/tcl/target/at91r40008.cfg +++ b/tcl/target/at91r40008.cfg @@ -43,7 +43,7 @@ $_TARGETNAME configure -event gdb-flash-erase-start { mww 0xffe00020 0x00000001 } -$_TARGETNAME configure -work-area-virt 0 -work-area-phys 0x3C000 -work-area-size 0x4000 -work-area-backup 0 +$_TARGETNAME configure -work-area-phys 0x3C000 -work-area-size 0x4000 -work-area-backup 0 flash bank cfi 0x10000000 0x400000 2 2 $_TARGETNAME diff --git a/tcl/target/at91rm9200.cfg b/tcl/target/at91rm9200.cfg index e20db520..e2972d72 100644 --- a/tcl/target/at91rm9200.cfg +++ b/tcl/target/at91rm9200.cfg @@ -42,7 +42,7 @@ set _TARGETNAME $_CHIPNAME.cpu target create $_TARGETNAME arm920t -endian $_ENDIAN -chain-position $_TARGETNAME # AT91RM9200 has a 16K block of sram @ 0x0020.0000 -$_TARGETNAME configure -work-area-virt 0x00200000 -work-area-phys 0x00200000 \ +$_TARGETNAME configure -work-area-phys 0x00200000 \ -work-area-size 0x4000 -work-area-backup 1 # This chip has a DCC ... use it diff --git a/tcl/target/at91sam3uXX.cfg b/tcl/target/at91sam3uXX.cfg index d54d3a4d..985e052a 100644 --- a/tcl/target/at91sam3uXX.cfg +++ b/tcl/target/at91sam3uXX.cfg @@ -33,7 +33,7 @@ set _TARGETNAME $_CHIPNAME.cpu target create $_TARGETNAME cortex_m3 -endian $_ENDIAN -chain-position $_TARGETNAME # 16K is plenty, the smallest chip has this much -$_TARGETNAME configure -work-area-virt 0 -work-area-phys 0x20000000 -work-area-size 16384 -work-area-backup 0 +$_TARGETNAME configure -work-area-phys 0x20000000 -work-area-size 16384 -work-area-backup 0 reset_config srst_only diff --git a/tcl/target/at91sam7sx.cfg b/tcl/target/at91sam7sx.cfg index 5cde979d..2a7f90c5 100644 --- a/tcl/target/at91sam7sx.cfg +++ b/tcl/target/at91sam7sx.cfg @@ -46,7 +46,7 @@ $_TARGETNAME configure -event reset-init { sleep 100 } -$_TARGETNAME configure -work-area-virt 0 -work-area-phys 0x00200000 -work-area-size 0x4000 -work-area-backup 0 +$_TARGETNAME configure -work-area-phys 0x00200000 -work-area-size 0x4000 -work-area-backup 0 #flash bank <driver> <base_addr> <size> <chip_width> <bus_width> <target_number> [<target_name> <banks> <sectors_per_bank> <pages_per_sector> <page_size> <num_nvmbits> <ext_freq_khz>] flash bank at91sam7 0 0 0 0 0 0 0 0 0 0 0 0 18432 diff --git a/tcl/target/at91sam9260.cfg b/tcl/target/at91sam9260.cfg index a6eaa76e..df08d10d 100644 --- a/tcl/target/at91sam9260.cfg +++ b/tcl/target/at91sam9260.cfg @@ -39,6 +39,6 @@ set _TARGETNAME $_CHIPNAME.cpu target create $_TARGETNAME arm926ejs -endian $_ENDIAN -chain-position $_TARGETNAME -variant arm926ejs # Internal sram1 memory -$_TARGETNAME configure -work-area-virt 0 -work-area-phys 0x00300000 -work-area-size 0x1000 -work-area-backup 1 +$_TARGETNAME configure -work-area-phys 0x00300000 -work-area-size 0x1000 -work-area-backup 1 diff --git a/tcl/target/at91sam9260_ext_RAM_ext_flash.cfg b/tcl/target/at91sam9260_ext_RAM_ext_flash.cfg index 2548962c..de7e9ab2 100644 --- a/tcl/target/at91sam9260_ext_RAM_ext_flash.cfg +++ b/tcl/target/at91sam9260_ext_RAM_ext_flash.cfg @@ -47,7 +47,7 @@ target create $_TARGETNAME arm926ejs -endian $_ENDIAN -chain-position $_TARGETNA $_TARGETNAME invoke-event halted # Internal sram1 memory -$_TARGETNAME configure -work-area-virt 0 -work-area-phys 0x00300000 -work-area-size 0x1000 -work-area-backup 1 +$_TARGETNAME configure -work-area-phys 0x00300000 -work-area-size 0x1000 -work-area-backup 1 scan_chain $_TARGETNAME configure -event reset-deassert-post {at91sam_init} diff --git a/tcl/target/cs351x.cfg b/tcl/target/cs351x.cfg index 237754ba..243f9639 100644 --- a/tcl/target/cs351x.cfg +++ b/tcl/target/cs351x.cfg @@ -24,7 +24,7 @@ target create $_TARGETNAME fa526 -endian $_ENDIAN -chain-position $_TARGETNAME - # There is 16K of SRAM on this chip # FIXME: flash programming is not working by using this work area. So comment this out for now. -#$_TARGETNAME configure -work-area-virt 0x00000000 -work-area-phys 0x00000000 -work-area-size 0x4000 -work-area-backup 1 +#$_TARGETNAME configure -work-area-phys 0x00000000 -work-area-size 0x4000 -work-area-backup 1 # This chip has a DCC ... use it arm7_9 dcc_downloads enable diff --git a/tcl/target/epc9301.cfg b/tcl/target/epc9301.cfg index 2b4155fb..eaf4ee96 100644 --- a/tcl/target/epc9301.cfg +++ b/tcl/target/epc9301.cfg @@ -24,7 +24,7 @@ jtag_nsrst_delay 100 jtag_ntrst_delay 100 set _TARGETNAME $_CHIPNAME.cpu -target create $_TARGETNAME arm920t -endian $_ENDIAN -chain-position $_TARGETNAME -work-area-virt 0 -work-area-phys 0x80014000 -work-area-size 0x1000 -work-area-backup 1 +target create $_TARGETNAME arm920t -endian $_ENDIAN -chain-position $_TARGETNAME -work-area-phys 0x80014000 -work-area-size 0x1000 -work-area-backup 1 #flash configuration #flash bank <driver> <base> <size> <chip_width> <bus_width> [driver_options ...] diff --git a/tcl/target/imx27.cfg b/tcl/target/imx27.cfg index 837ea614..4a93a675 100644 --- a/tcl/target/imx27.cfg +++ b/tcl/target/imx27.cfg @@ -40,7 +40,9 @@ jtag newtap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_C # Create the GDB Target. set _TARGETNAME $_CHIPNAME.cpu target create $_TARGETNAME arm926ejs -endian $_ENDIAN -chain-position $_TARGETNAME -variant arm926ejs -$_TARGETNAME configure -work-area-virt 0xffff4c00 -work-area-phys 0xffff4c00 -work-area-size 0x8000 -work-area-backup 1 +# REVISIT what operating environment sets up this virtual address mapping? +$_TARGETNAME configure -work-area-virt 0xffff4c00 -work-area-phys 0xffff4c00 \ + -work-area-size 0x8000 -work-area-backup 1 # Internal to the chip, there is 45K of SRAM # diff --git a/tcl/target/is5114.cfg b/tcl/target/is5114.cfg index 8c153347..091bfc2f 100644 --- a/tcl/target/is5114.cfg +++ b/tcl/target/is5114.cfg @@ -46,4 +46,4 @@ $_TARGETNAME configure -event reset-init { # We can increase speed now that we know the target is halted. jtag_rclk 3000 } -$_TARGETNAME configure -work-area-phys 0x50000000 -work-area-virt 0x50000000 -work-area-size 16384 -work-area-backup 1 +$_TARGETNAME configure -work-area-phys 0x50000000 -work-area-size 16384 -work-area-backup 1 diff --git a/tcl/target/lpc1768.cfg b/tcl/target/lpc1768.cfg index 63ec1bb3..9f6bcffc 100644 --- a/tcl/target/lpc1768.cfg +++ b/tcl/target/lpc1768.cfg @@ -31,7 +31,7 @@ set _TARGETNAME $_CHIPNAME.cpu target create $_TARGETNAME cortex_m3 -endian $_ENDIAN -chain-position $_TARGETNAME # LPC1768 has 32kB of SRAM on its main system bus (so-called Local On-Chip SRAM) -$_TARGETNAME configure -work-area-virt 0 -work-area-phys 0x10000000 -work-area-size 0x8000 -work-area-backup 0 +$_TARGETNAME configure -work-area-phys 0x10000000 -work-area-size 0x8000 -work-area-backup 0 $_TARGETNAME configure -event reset-init { # Force target into ARM state diff --git a/tcl/target/lpc2103.cfg b/tcl/target/lpc2103.cfg index 1a880761..0aadee8e 100644 --- a/tcl/target/lpc2103.cfg +++ b/tcl/target/lpc2103.cfg @@ -31,7 +31,7 @@ set _TARGETNAME $_CHIPNAME.cpu target create $_TARGETNAME arm7tdmi -endian $_ENDIAN -chain-position $_TARGETNAME -variant arm7tdmi-s_r4 # 8kB of internal SRAM -$_TARGETNAME configure -work-area-virt 0 -work-area-phys 0x40000000 -work-area-size 0x2000 -work-area-backup 0 +$_TARGETNAME configure -work-area-phys 0x40000000 -work-area-size 0x2000 -work-area-backup 0 # 32kB of internal Flash, core clocked with 12MHz crystal # flash bank lpc2000 <base> <size> 0 0 <target#> <variant> <clock> [calc_checksum] diff --git a/tcl/target/lpc2124.cfg b/tcl/target/lpc2124.cfg index 61d411b5..471286b8 100644 --- a/tcl/target/lpc2124.cfg +++ b/tcl/target/lpc2124.cfg @@ -35,7 +35,7 @@ jtag newtap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_CP set _TARGETNAME $_CHIPNAME.cpu target create $_TARGETNAME arm7tdmi -endian $_ENDIAN -chain-position $_TARGETNAME -variant arm7tdmi-s_r4 -$_TARGETNAME configure -work-area-virt 0 -work-area-phys 0x40000000 -work-area-size 0x4000 -work-area-backup 0 +$_TARGETNAME configure -work-area-phys 0x40000000 -work-area-size 0x4000 -work-area-backup 0 #flash bank <driver> <base> <size> <chip_width> <bus_width> diff --git a/tcl/target/lpc2129.cfg b/tcl/target/lpc2129.cfg index 5438fc3c..a686a471 100644 --- a/tcl/target/lpc2129.cfg +++ b/tcl/target/lpc2129.cfg @@ -35,7 +35,7 @@ jtag newtap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_CP set _TARGETNAME $_CHIPNAME.cpu target create $_TARGETNAME arm7tdmi -endian $_ENDIAN -chain-position $_TARGETNAME -variant arm7tdmi-s_r4 -$_TARGETNAME configure -work-area-virt 0 -work-area-phys 0x40000000 -work-area-size 0x4000 -work-area-backup 0 +$_TARGETNAME configure -work-area-phys 0x40000000 -work-area-size 0x4000 -work-area-backup 0 #flash bank <driver> <base> <size> <chip_width> <bus_width> flash bank lpc2000 0x0 0x40000 0 0 $_TARGETNAME lpc2000_v1 14765 calc_checksum diff --git a/tcl/target/lpc2148.cfg b/tcl/target/lpc2148.cfg index b5023437..ce672c88 100644 --- a/tcl/target/lpc2148.cfg +++ b/tcl/target/lpc2148.cfg @@ -35,7 +35,7 @@ jtag newtap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_CP set _TARGETNAME $_CHIPNAME.cpu target create $_TARGETNAME arm7tdmi -endian $_ENDIAN -chain-position $_TARGETNAME -variant arm7tdmi-s_r4 -$_TARGETNAME configure -work-area-virt 0 -work-area-phys 0x40000000 -work-area-size 0x4000 -work-area-backup 0 +$_TARGETNAME configure -work-area-phys 0x40000000 -work-area-size 0x4000 -work-area-backup 0 $_TARGETNAME configure -event reset-init { # Force target into ARM state diff --git a/tcl/target/lpc2294.cfg b/tcl/target/lpc2294.cfg index 08fbf581..a34940ed 100644 --- a/tcl/target/lpc2294.cfg +++ b/tcl/target/lpc2294.cfg @@ -28,7 +28,7 @@ jtag newtap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_CP set _TARGETNAME $_CHIPNAME.cpu target create $_TARGETNAME arm7tdmi -endian $_ENDIAN -chain-position $_TARGETNAME -variant arm7tdmi-s_r4 -$_TARGETNAME configure -work-area-virt 0 -work-area-phys 0x40000000 -work-area-size 0x4000 -work-area-backup 0 +$_TARGETNAME configure -work-area-phys 0x40000000 -work-area-size 0x4000 -work-area-backup 0 #flash configuration #flash bank lpc2000 <base> <size> 0 0 <target#> <variant> diff --git a/tcl/target/lpc2378.cfg b/tcl/target/lpc2378.cfg index 34b9963f..7f716f3d 100644 --- a/tcl/target/lpc2378.cfg +++ b/tcl/target/lpc2378.cfg @@ -31,7 +31,7 @@ set _TARGETNAME $_CHIPNAME.cpu target create $_TARGETNAME arm7tdmi -endian $_ENDIAN -chain-position $_TARGETNAME -variant arm7tdmi-s_r4 # LPC2378 has 32kB of SRAM on its main system bus (so-called Local On-Chip SRAM) -$_TARGETNAME configure -work-area-virt 0 -work-area-phys 0x40000000 -work-area-size 0x8000 -work-area-backup 0 +$_TARGETNAME configure -work-area-phys 0x40000000 -work-area-size 0x8000 -work-area-backup 0 $_TARGETNAME configure -event reset-init { # Force target into ARM state diff --git a/tcl/target/lpc2478.cfg b/tcl/target/lpc2478.cfg index bf33ae0e..e78afa1a 100644 --- a/tcl/target/lpc2478.cfg +++ b/tcl/target/lpc2478.cfg @@ -31,7 +31,7 @@ set _TARGETNAME $_CHIPNAME.cpu target create $_TARGETNAME arm7tdmi -endian $_ENDIAN -chain-position $_TARGETNAME -variant arm7tdmi-s_r4 # LPC2478 has 64kB of SRAM on its main system bus (so-called Local On-Chip SRAM) -$_TARGETNAME configure -work-area-virt 0 -work-area-phys 0x40000000 -work-area-size 0x10000 -work-area-backup 0 +$_TARGETNAME configure -work-area-phys 0x40000000 -work-area-size 0x10000 -work-area-backup 0 $_TARGETNAME configure -event reset-init { # Force target into ARM state diff --git a/tcl/target/mega128.cfg b/tcl/target/mega128.cfg index 6c0ad859..e444889e 100644 --- a/tcl/target/mega128.cfg +++ b/tcl/target/mega128.cfg @@ -20,7 +20,7 @@ jtag newtap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_CP set _TARGETNAME $_CHIPNAME.cpu target create $_TARGETNAME avr -endian $_ENDIAN -chain-position $_TARGETNAME -#$_TARGETNAME configure -work-area-virt 0 -work-area-phys 0x20000000 -work-area-size 16384 -work-area-backup 0 +#$_TARGETNAME configure -work-area-phys 0x20000000 -work-area-size 16384 -work-area-backup 0 flash bank avr 0 0 0 0 0 diff --git a/tcl/target/omap5912.cfg b/tcl/target/omap5912.cfg index b578457b..d825df7f 100644 --- a/tcl/target/omap5912.cfg +++ b/tcl/target/omap5912.cfg @@ -48,5 +48,5 @@ proc omap5912_reset {} { } # omap5912 lcd frame buffer as working area -$_TARGETNAME configure -work-area-virt 0 -work-area-phys 0x20000000 \ +$_TARGETNAME configure -work-area-phys 0x20000000 \ -work-area-size 0x3e800 -work-area-backup 0 diff --git a/tcl/target/pic32mx.cfg b/tcl/target/pic32mx.cfg index daa54eb9..6127a540 100644 --- a/tcl/target/pic32mx.cfg +++ b/tcl/target/pic32mx.cfg @@ -31,7 +31,7 @@ jtag newtap $_CHIPNAME cpu -irlen 5 -ircapture 0x1 -irmask 0x1f -expected-id $_ set _TARGETNAME $_CHIPNAME.cpu target create $_TARGETNAME mips_m4k -endian $_ENDIAN -chain-position $_TARGETNAME -$_TARGETNAME configure -work-area-virt 0 -work-area-phys 0xa0000000 -work-area-size 16384 -work-area-backup 0 +$_TARGETNAME configure -work-area-phys 0xa0000000 -work-area-size 16384 -work-area-backup 0 flash bank pic32mx 0xbd000000 0 0 0 0 flash bank pic32mx 0xbfc00000 0 0 0 0 diff --git a/tcl/target/pxa270.cfg b/tcl/target/pxa270.cfg index 84fc2f77..6ca057ca 100644 --- a/tcl/target/pxa270.cfg +++ b/tcl/target/pxa270.cfg @@ -41,4 +41,4 @@ jtag newtap $_CHIPNAME cpu -irlen 7 -ircapture 0x1 -irmask 0x7f -expected-id $_C target create $_TARGETNAME xscale -endian $_ENDIAN -chain-position $_TARGETNAME -variant pxa27x # maps to PXA internal RAM. If you are using a PXA255 # you must initialize SDRAM or leave this option off -$_TARGETNAME configure -work-area-virt 0 -work-area-phys 0x5c000000 -work-area-size 0x10000 -work-area-backup 0 +$_TARGETNAME configure -work-area-phys 0x5c000000 -work-area-size 0x10000 -work-area-backup 0 diff --git a/tcl/target/sam7se512.cfg b/tcl/target/sam7se512.cfg index 4b1d85bf..0f1e4126 100644 --- a/tcl/target/sam7se512.cfg +++ b/tcl/target/sam7se512.cfg @@ -32,7 +32,7 @@ jtag newtap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_CP set _TARGETNAME $_CHIPNAME.cpu target create $_TARGETNAME arm7tdmi -endian $_ENDIAN -chain-position $_TARGETNAME -variant arm7tdmi -$_TARGETNAME configure -work-area-virt 0 -work-area-phys 0x00200000 -work-area-size 0x4000 -work-area-backup 0 +$_TARGETNAME configure -work-area-phys 0x00200000 -work-area-size 0x4000 -work-area-backup 0 #flash bank <driver> <base_addr> <size> <chip_width> <bus_width> <target_number> [<target_name> <banks> <sectors_per_bank> <pages_per_sector> <page_size> <num_nvmbits> <ext_freq_khz>] flash bank at91sam7 0 0 0 0 0 0 0 0 0 0 0 0 18432 diff --git a/tcl/target/sam7x256.cfg b/tcl/target/sam7x256.cfg index 12f30305..c3f7cd9c 100644 --- a/tcl/target/sam7x256.cfg +++ b/tcl/target/sam7x256.cfg @@ -43,7 +43,7 @@ $_TARGETNAME configure -event reset-init { sleep 100 } -$_TARGETNAME configure -work-area-virt 0 -work-area-phys 0x00200000 -work-area-size 0x4000 -work-area-backup 0 +$_TARGETNAME configure -work-area-phys 0x00200000 -work-area-size 0x4000 -work-area-backup 0 #flash bank <driver> <base_addr> <size> <chip_width> <bus_width> <target_number> [<target_name> <banks> <sectors_per_bank> <pages_per_sector> <page_size> <num_nvmbits> <ext_freq_khz>] flash bank at91sam7 0 0 0 0 0 0 0 0 0 0 0 0 18432 diff --git a/tcl/target/samsung_s3c2410.cfg b/tcl/target/samsung_s3c2410.cfg index e845eb59..9682c4c1 100644 --- a/tcl/target/samsung_s3c2410.cfg +++ b/tcl/target/samsung_s3c2410.cfg @@ -28,7 +28,7 @@ jtag newtap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_CP set _TARGETNAME $_CHIPNAME.cpu target create $_TARGETNAME arm920t -endian $_ENDIAN -chain-position $_TARGETNAME -variant arm920t -$_TARGETNAME configure -work-area-virt 0 -work-area-phys 0x30800000 -work-area-size 0x20000 -work-area-backup 0 +$_TARGETNAME configure -work-area-phys 0x30800000 -work-area-size 0x20000 -work-area-backup 0 # speed up memory downloads arm7_9 fast_memory_access enable diff --git a/tcl/target/samsung_s3c2440.cfg b/tcl/target/samsung_s3c2440.cfg index f9263a52..d3b665ff 100644 --- a/tcl/target/samsung_s3c2440.cfg +++ b/tcl/target/samsung_s3c2440.cfg @@ -29,7 +29,7 @@ jtag newtap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0x0f -expected-id $_C set _TARGETNAME $_CHIPNAME.cpu target create $_TARGETNAME arm920t -endian $_ENDIAN -chain-position $_TARGETNAME -variant arm920t -$_TARGETNAME configure -work-area-virt 0 -work-area-phys 0x200000 -work-area-size 0x4000 -work-area-backup 1 +$_TARGETNAME configure -work-area-phys 0x200000 -work-area-size 0x4000 -work-area-backup 1 #reset configuration reset_config trst_and_srst diff --git a/tcl/target/stm32.cfg b/tcl/target/stm32.cfg index 97d76789..619824c5 100644 --- a/tcl/target/stm32.cfg +++ b/tcl/target/stm32.cfg @@ -63,7 +63,7 @@ jtag newtap $_CHIPNAME bs -irlen 5 -expected-id $_BSTAPID1 \ set _TARGETNAME $_CHIPNAME.cpu target create $_TARGETNAME cortex_m3 -endian $_ENDIAN -chain-position $_TARGETNAME -$_TARGETNAME configure -work-area-virt 0 -work-area-phys 0x20000000 -work-area-size $_WORKAREASIZE -work-area-backup 0 +$_TARGETNAME configure -work-area-phys 0x20000000 -work-area-size $_WORKAREASIZE -work-area-backup 0 flash bank stm32x 0 0 0 0 $_TARGETNAME diff --git a/tcl/target/str710.cfg b/tcl/target/str710.cfg index 215d12bb..8e5d36f0 100644 --- a/tcl/target/str710.cfg +++ b/tcl/target/str710.cfg @@ -36,7 +36,7 @@ $_TARGETNAME configure -event gdb-flash-erase-start { flash protect 1 0 1 off } -$_TARGETNAME configure -work-area-virt 0 -work-area-phys 0x2000C000 -work-area-size 0x4000 -work-area-backup 0 +$_TARGETNAME configure -work-area-phys 0x2000C000 -work-area-size 0x4000 -work-area-backup 0 #flash bank str7x <base> <size> 0 0 <target#> <variant> flash bank str7x 0x40000000 0x00040000 0 0 0 STR71x diff --git a/tcl/target/str730.cfg b/tcl/target/str730.cfg index d9e9ecf1..fe70802b 100644 --- a/tcl/target/str730.cfg +++ b/tcl/target/str730.cfg @@ -40,7 +40,7 @@ $_TARGETNAME configure -event gdb-flash-erase-start { flash protect 0 0 7 off } -$_TARGETNAME configure -work-area-virt 0 -work-area-phys 0x40000000 -work-area-size 0x4000 -work-area-backup 0 +$_TARGETNAME configure -work-area-phys 0x40000000 -work-area-size 0x4000 -work-area-backup 0 #flash bank <driver> <base> <size> <chip_width> <bus_width> flash bank str7x 0x20000000 0x00040000 0 0 0 STR3x diff --git a/tcl/target/str750.cfg b/tcl/target/str750.cfg index 74f26642..22d87f87 100644 --- a/tcl/target/str750.cfg +++ b/tcl/target/str750.cfg @@ -43,7 +43,7 @@ $_TARGETNAME configure -event gdb-flash-erase-start { flash protect 1 0 1 off } -$_TARGETNAME configure -work-area-virt 0 -work-area-phys 0x40000000 -work-area-size 0x4000 -work-area-backup 0 +$_TARGETNAME configure -work-area-phys 0x40000000 -work-area-size 0x4000 -work-area-backup 0 #flash bank <driver> <base> <size> <chip_width> <bus_width> flash bank str7x 0x20000000 0x00040000 0 0 0 STR75x diff --git a/tcl/target/str912.cfg b/tcl/target/str912.cfg index b8f8f1ac..0dd68483 100644 --- a/tcl/target/str912.cfg +++ b/tcl/target/str912.cfg @@ -60,7 +60,7 @@ $_TARGETNAME configure -event reset-init { flash protect 0 0 7 off } -$_TARGETNAME configure -work-area-virt 0 -work-area-phys 0x50000000 -work-area-size 16384 -work-area-backup 0 +$_TARGETNAME configure -work-area-phys 0x50000000 -work-area-size 16384 -work-area-backup 0 #flash bank str9x <base> <size> 0 0 <target#> <variant> flash bank str9x 0x00000000 0x00080000 0 0 0 diff --git a/tcl/target/tmpa900.cfg b/tcl/target/tmpa900.cfg index 719c9769..80adc652 100644 --- a/tcl/target/tmpa900.cfg +++ b/tcl/target/tmpa900.cfg @@ -52,5 +52,5 @@ target create $_TARGETNAME arm926ejs -endian $_ENDIAN -chain-position $_TARGETNA #working_area 0 0xf8004000 0xc000 nobackup # Internal sram1 memory -$_TARGETNAME configure -work-area-virt 0 -work-area-phys 0xf8004000 -work-area-size 0x8000 \ +$_TARGETNAME configure -work-area-phys 0xf8004000 -work-area-size 0x8000 \ -work-area-backup 0 diff --git a/tcl/target/tmpa910.cfg b/tcl/target/tmpa910.cfg index 4a0ec71b..4af5e4e8 100644 --- a/tcl/target/tmpa910.cfg +++ b/tcl/target/tmpa910.cfg @@ -52,5 +52,5 @@ target create $_TARGETNAME arm926ejs -endian $_ENDIAN -chain-position $_TARGETNA #working_area 0 0xf8004000 0xc000 nobackup # Internal sram1 memory -$_TARGETNAME configure -work-area-virt 0 -work-area-phys 0xf8004000 -work-area-size 0xc000 \ +$_TARGETNAME configure -work-area-phys 0xf8004000 -work-area-size 0xc000 \ -work-area-backup 0 diff --git a/tcl/target/xba_revA3.cfg b/tcl/target/xba_revA3.cfg index e1c88705..9d258a52 100644 --- a/tcl/target/xba_revA3.cfg +++ b/tcl/target/xba_revA3.cfg @@ -76,7 +76,7 @@ $_TARGETNAME configure -event reset-init { flash probe 0 } -$_TARGETNAME configure -work-area-virt 0 -work-area-phys 0x20010000 -work-area-size 0x8060 -work-area-backup 0 +$_TARGETNAME configure -work-area-phys 0x20010000 -work-area-size 0x8060 -work-area-backup 0 flash bank cfi 0x50000000 0x400000 2 2 $_TARGETNAME diff --git a/tcl/test/syntax1.cfg b/tcl/test/syntax1.cfg index 93beefca..40a7c1db 100644 --- a/tcl/test/syntax1.cfg +++ b/tcl/test/syntax1.cfg @@ -16,7 +16,7 @@ jtag newtap lpc2148 one -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id 0x4f1f0 #daemon_startup reset set _TARGETNAME [format "%s.cpu" lpc2148] -target create lpc2148.cpu arm7tdmi -endian little -work-area-size 0x4000 -work-area-phys 0x40000000 -work-area-virt 0 -work-area-backup 0 +target create lpc2148.cpu arm7tdmi -endian little -work-area-size 0x4000 -work-area-phys 0x40000000 -work-area-backup 0 $_TARGETNAME configure -event reset-init { soft_reset_halt |