summaryrefslogtreecommitdiff
path: root/tcl
diff options
context:
space:
mode:
Diffstat (limited to 'tcl')
-rw-r--r--tcl/target/davinci.cfg63
1 files changed, 62 insertions, 1 deletions
diff --git a/tcl/target/davinci.cfg b/tcl/target/davinci.cfg
index 658e7fe5..e1eb48f5 100644
--- a/tcl/target/davinci.cfg
+++ b/tcl/target/davinci.cfg
@@ -33,7 +33,7 @@ proc mmw {reg setbits clearbits} {
#
# PLL version 0x02: tested on dm355
-# REVISIT: On dm6446 and dm357 the PLLRST polarity is different.
+# REVISIT: On dm6446/dm357 the PLLRST polarity is different.
proc pll_v02_setup {pll_addr mult config} {
set pll_ctrl_addr [expr $pll_addr + 0x100]
set pll_ctrl [mrw $pll_ctrl_addr]
@@ -174,3 +174,64 @@ proc psc_go {} {
# wait for PTSTAT.go to clear (again ignoring DSP power domain)
while { [expr [mrw $ptstat_addr] & 0x01] != 0 } { sleep 1 }
}
+
+#
+# A reset using only SRST is a "Warm Reset", resetting everything in the
+# chip except ARM emulation (and everything _outside_ the chip that hooks
+# up to SRST). But many boards don't expose SRST via their JTAG connectors
+# (it's not present on TI-14 headers).
+#
+# From the chip-only perspective, a "Max Reset" is a "Warm" reset ... except
+# without any board-wide side effects, since it's triggered using JTAG using
+# either (a) ARM watchdog timer, or (b) ICEpick.
+#
+proc davinci_wdog_reset {} {
+ set timer2_phys 0x01c21c00
+
+ # NOTE -- on entry
+ # - JTAG communication with the ARM *must* be working OK; this
+ # may imply using adaptive clocking or disabling WFI-in-idle
+ # - current target must be the DaVinci ARM
+ # - that ARM core must be halted
+ # - timer2 clock is still enabled (PSC 29 on most chips)
+
+ #
+ # Part I -- run regardless of being halted via JTAG
+ #
+ # NOTE: for now, we assume there's no DSP that could control the
+ # watchdog; or, equivalently, SUSPSRC.TMR2SRC says the watchdog
+ # suspend signal is controlled via ARM emulation suspend.
+ #
+
+ # EMUMGT_CLKSPEED: write FREE bit to run despite emulation halt
+ arm926ejs mww_phys [expr $timer2_phys + 0x28] 0x00004000
+
+ #
+ # Part II -- in case watchdog hasn't been set up
+ #
+
+ # TCR: disable, force internal clock source
+ arm926ejs mww_phys [expr $timer2_phys + 0x20] 0
+
+ # TGCR: reset, force to 64-bit wdog mode, un-reset ("initial" state)
+ arm926ejs mww_phys [expr $timer2_phys + 0x24] 0
+ arm926ejs mww_phys [expr $timer2_phys + 0x24] 0x110b
+
+ # clear counter (TIM12, TIM34) and period (PRD12, PRD34) registers
+ # so watchdog triggers ASAP
+ arm926ejs mww_phys [expr $timer2_phys + 0x10] 0
+ arm926ejs mww_phys [expr $timer2_phys + 0x14] 0
+ arm926ejs mww_phys [expr $timer2_phys + 0x18] 0
+ arm926ejs mww_phys [expr $timer2_phys + 0x1c] 0
+
+ # WDTCR: put into pre-active state, then active
+ arm926ejs mww_phys [expr $timer2_phys + 0x28] 0xa5c64000
+ arm926ejs mww_phys [expr $timer2_phys + 0x28] 0xda7e4000
+
+ #
+ # Part III -- it's ready to rumble
+ #
+
+ # WDTCR: write invalid WDKEY to trigger reset
+ arm926ejs mww_phys [expr $timer2_phys + 0x28] 0x00004000
+}