summaryrefslogtreecommitdiff
Commit message (Collapse)AuthorAgeFilesLines
* arm_jtag_scann error propagation fixesØyvind Harboe2010-07-205-12/+34
| | | | Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
* arm_dpm: error propagation fixesØyvind Harboe2010-07-191-2/+26
| | | | | | found by inspection Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
* adi_jtag_ error propagationØyvind Harboe2010-07-191-4/+12
| | | | Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
* arm: error propagation of arm_jtag_set_instrØyvind Harboe2010-07-1910-32/+108
| | | | Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
* arm_adi_v5: dap_run() error propagationØyvind Harboe2010-07-191-15/+28
| | | | Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
* arm_adi_v5: mem_ap_write error propagationØyvind Harboe2010-07-192-25/+78
| | | | Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
* arm_adi_v5: error propagation of mem_ap_read_atomic_u32 failureØyvind Harboe2010-07-192-26/+73
| | | | Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
* mem_ap_read_u32 error propagationØyvind Harboe2010-07-192-16/+48
| | | | Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
* arm_adi_v5: add error propagation for dap_setup_accessportØyvind Harboe2010-07-192-15/+45
| | | | Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
* debug: debug entry error propagationØyvind Harboe2010-07-1911-41/+116
| | | | Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
* cortex a8: added timeout handlingØyvind Harboe2010-07-191-5/+28
| | | | Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
* arm: add error propagation for enable/disable mmu cachesØyvind Harboe2010-07-198-65/+162
| | | | Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
* arm: add error propagation to generic get_ttb fnØyvind Harboe2010-07-198-18/+46
| | | | Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
* more careful luminary initDavid Brownell2010-07-191-7/+12
| | | | | | | | | | | Set up more of the Luminary-specific signals, and stop cloning a few of the JTAG defaults. More comments too. Still leaves the "dap info 0" bugs unresolved (presumably coupled to this particular adapter family) where TPIU, ITM, DWT, and other debug modules wrongly display as extra NVICs. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
* cfg: add Amontec JTAGkey2p interface config (Issue #26)Spencer Oliver2010-07-191-0/+11
| | | | Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
* flash: add nuc910 nand driverSpencer Oliver2010-07-195-2/+309
| | | | | | | | This adds a nand driver support for the nuc910 target. Note that ECC is not currently supported by this driver, although it is supported by the peripheral. Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
* nand: nand probe also outputs manufacturerSpencer Oliver2010-07-191-1/+2
| | | | | | The nand probe now outputs the manufacturer if found. Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
* cfg: update rsc-w910 scriptSpencer Oliver2010-07-191-1/+2
| | | | | | | - Only enable the FMI (NAND) and DMA clocks. - Select NAND interface on the MFSEL. Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
* docs: missing parameter from nand check_bad_blocksSpencer Oliver2010-07-191-1/+1
| | | | Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
* cortex a8: lots of error propagation fixesØyvind Harboe2010-07-191-18/+53
| | | | | | found by code inspection Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
* cortex a8: mem_ap_read_buf_u32() error handlingØyvind Harboe2010-07-191-1/+3
| | | | Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
* cortex a8: add missing error handling for ↵Øyvind Harboe2010-07-191-3/+9
| | | | | | cortex_a8_dap_write/read_coreregister_u32() Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
* cortex a8: add missing error handling from cortex_a8_exec_opcode()Øyvind Harboe2010-07-191-13/+52
| | | | Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
* cortex a8: add missing error handling for mem_ap_atomic_write_u32()Øyvind Harboe2010-07-191-1/+5
| | | | Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
* cortex a8: add missing error handling for mem_ap_read_atomic_u32()Øyvind Harboe2010-07-191-0/+11
| | | | Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
* comments for Luminary ICDI layoutDavid Brownell2010-07-181-3/+27
| | | | | | | Provide $defines for more of the signals involved in the Luminary ICDI hardware, and comment some of what's going on. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
* spelling fixes in commentsØyvind Harboe2010-07-181-5/+5
| | | | Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
* debug-feature: jtagtcpip, improve jtag performanceØyvind Harboe2010-07-182-4/+76
| | | | | | postpone callbacks until jtag execute queue time. Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
* lm3s811-ek uses generic stellaris target configDavid Brownell2010-07-173-32/+5
| | | | | | | There's no point in an lm3s811-specific target file, so remove it in favor of the generic "stellaris.cfg". Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
* ARM ADI-V5: cleanup CID/PID addressingDavid Brownell2010-07-161-21/+23
| | | | | | | | | | | Use addition for offsetting, not masking. Shorten some lines. Make "component_start" print-only (unused otherwise; don't save). Still doesn't resolve the issue where multiple components are wrongly displaying as NVICs on some Cortex-M3 parts because many PIDs appear to be zeroes ... maybe adapter related?? Signed-off-by: David Brownell <db@helium.(none)>
* flash: use bkpt for str9 flash algo algorithmSpencer Oliver2010-07-161-3/+2
| | | | | | | STR9 is ARMv5 arch so use bkpt instruction rather than waste a breakpoint. Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
* fix warningsØyvind Harboe2010-07-161-2/+1
| | | | Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
* debug-feature: jtagtcpip, reduce performance impact of ping timesØyvind Harboe2010-07-162-46/+103
| | | | | | queue read back of data Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
* debug feature: jtagtcpip, improve performanceØyvind Harboe2010-07-162-0/+26
| | | | | | | | | waiting for ZY1000 fifo to idle is now queued as an asynchronous command. This radically improves performance when waitIdle() is interspersed with writes as no readback is required over TCP/IP. Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
* debug feature: jtagtcpip, improved performanceØyvind Harboe2010-07-161-9/+22
| | | | | | only check error flag when rclk is actually enabled. Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
* ARM ADI-V5: PIDs and CIDs are 8 bitsDavid Brownell2010-07-131-21/+41
| | | | | | | | | Mask the upper bits after 32-bit reads. Alsoo revert the ugly changes to use PRIx32; just cast to unsized integers when printing (two chars not eight). Signed-off-by: David Brownell <db@helium.(none)>
* cfg: add Avalue RSC-W910 configSpencer Oliver2010-07-132-0/+89
| | | | Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
* jtag: fix shadow issues in adapter_initSpencer Oliver2010-07-121-1/+0
| | | | | | Use global jtag_only rather than local static. Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
* arm9: revert change arm9tdmi cmd group name to arm9Spencer Oliver2010-07-121-2/+2
| | | | | | | | | This reverts the incorrect change made to the arm9 cmd group in commit d1eca9a74c7c57ba6a3210c51b2a10cc5adb22e1. The code now matches the docs and the release notes. Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
* docs: fix transport typoSpencer Oliver2010-07-121-2/+2
| | | | Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
* adapter.c: missing space in handle_interface_commandSpencer Oliver2010-07-121-1/+1
| | | | Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
* transport selection tweaksDavid Brownell2010-07-095-15/+39
| | | | | | | | | | | | * Bugfix and simplify legacy jtag-only defaulting * Make "dummy" declare its jtag-only nature * likewise update ft2232 * warn if selection is _required_ (multi-transport adapters), fixes the "only ft2232 works" bug for at least dummy, with other drivers going the "legacy" path (submit patches). Signed-off-by: David Brownell <db@helium.(none)>
* transport: fix bug/typo in transport_register cmdSpencer Oliver2010-07-093-5/+3
| | | | Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
* transport: fix segfault in transport selectØyvind Harboe2010-07-071-7/+6
| | | | | | | String compare against addresses in range 0 or so due to not checking if there was an active session first. Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
* transport: fix bug/typo in interface_transports commandØyvind Harboe2010-07-071-1/+2
| | | | | | | Classic manifestation of weakness of dangling { formatting :-) Hard to spot these sort of mistakes visually. Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
* gdbserver: incorrect memory map for multiple targets (bug #24)sb-sf2010-07-051-2/+4
| | | | | | | The gdb server incorrectly reports the memory map if we have multiple targets with multiple flash banks. Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
* transport: fix segfault in setup_command_handler()Stacey Sheldon2010-07-051-0/+1
| | | | | | | | Commit 93f2afa45f4c dropped the sentinel off the end of the command_registrants[] array. The loop immediately following the initialization will walk right off the end. Signed-off-by: Stacey Sheldon <stac@solidgoldbomb.org>
* Fix minor openocd.texi bugDavid Brownell2010-07-021-0/+1
| | | | | ::X Signed-off-by: David Brownell <db@helium.(none)>
* initial "transport" frameworkDavid Brownell2010-07-0210-30/+633
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | This adds the guts of a transport framework with initialization, which should work with current JTAG-only configurations (tested with FT2232). Each debug adapter can declare the transports it supports, and exactly one transport is initialized. (with its commands) in any given OpenOCD session. * Define a new "struct transport with init hooks and a few "transport" subcommands to support it: "list" ... list the transports configured (just "jtag" for now) "select" ... makes the debug session use that transport "init" ... initializes the selected transport (internal) * "interface_transports" ... declares transports the current interface can support. (Some will do this from C code instead, when there are no hardware versioning (or other) issues to prevent it. Plus some FT2232 tweaks, including a few to streamline upcoming support for an SWD transport (initially for Luminary adapters). Eventually src/jtag should probably become src/transport, moving jtag-specific stuff to transport/jtag. Signed-off-by: David Brownell <db@helium.(none)>
* ft2232: revert ft2232_read_scan changesSpencer Oliver2010-07-021-10/+9
| | | | | | | Revert change made in commit dd88b461da1cb8642200dd5c96fb1ff384ca9f7b. Caused segfaults when using ftdi driver under win32. Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
generated by cgit v1.2.3 (git 2.46.0) at 2024-12-29 17:45:40 +0000