summaryrefslogtreecommitdiff
path: root/doc
Commit message (Collapse)AuthorAgeFilesLines
* David Brownell <david-b@pacbell.net>:zwelch2009-06-041-178/+217
| | | | | | | | | | | | | | | | | Convert the Interface/Dongle Config chapter's section on drivers to use the @deffn syntax, and integrate the presentation of the driver-specific commands with the relevant driver. Alphabetize. Cross-checked against the code ... several adapters were not listed, and a few commands weren't. (Maintainers for the versaloon and zy1000 drivers would be good candidates to add the commands missing from those sections...) git-svn-id: svn://svn.berlios.de/openocd/trunk@2035 b42882b7-edfa-0310-969c-e2dbd0fdcd60
* David Brownell <david-b@pacbell.net>:zwelch2009-06-041-74/+85
| | | | | | | | | | Convert the str9xpec driver info to use @deffn; alphabetize; add the missing part_id command. Convert the mflash support to use @deffn; alphabetize. git-svn-id: svn://svn.berlios.de/openocd/trunk@2034 b42882b7-edfa-0310-969c-e2dbd0fdcd60
* Improve remaining documentation that was causing Doxygen warnings.zwelch2009-06-032-2/+2
| | | | git-svn-id: svn://svn.berlios.de/openocd/trunk@2026 b42882b7-edfa-0310-969c-e2dbd0fdcd60
* Add architectural introduction to the JTAG module in The Manual.zwelch2009-06-032-16/+39
| | | | git-svn-id: svn://svn.berlios.de/openocd/trunk@2024 b42882b7-edfa-0310-969c-e2dbd0fdcd60
* Add draft of Patching Primer in The Manual; update primer page.zwelch2009-06-032-0/+222
| | | | git-svn-id: svn://svn.berlios.de/openocd/trunk@2021 b42882b7-edfa-0310-969c-e2dbd0fdcd60
* David Brownell <david-b@pacbell.net>:zwelch2009-06-031-74/+200
| | | | | | | | | | | | | | | | | | | | | Update docs for most of the remaining commands in jtag.c: - switch to @deffn - these are just the "low level" JTAG commands - resolve much goofage! * remove docs for non-existent commands * add missing docs for some existing commands * fix incorrect docs for some commands - just index TAP states overall, not individually - current name is "RUN/IDLE" not "IDLE" Cross checked against the source. This also creates an "Interface Drivers" section, analagous to how (NOR) Flash and NAND drivers are presented; that's not yet sorted. git-svn-id: svn://svn.berlios.de/openocd/trunk@2014 b42882b7-edfa-0310-969c-e2dbd0fdcd60
* David Brownell <david-b@pacbell.net>:zwelch2009-06-031-254/+292
| | | | | | | | | | | | | | | | | | | | | | | | | | Rework the TAP creation documentation. - Try to use "TAP" not "tap" everywhere; it's an acronym. - Update the associated "target config files" section: * reference the "TAP Creation" chapter for details * simplify: reference interesting multi-tap config files * let's not forget CPU configuration (*before* workspace setup) * streamline it a bit * move that workspace-vs-mmu issue to a better location - Clean up TAP creation doc mess * switch to @deffn * (re)organize the remaining stuff * reference the "Config File Guidelines" chapter - Tweak the "Target Configuration" chapter * rename as "CPU configuration"; unconfuse vs. target/*.cfg * bring out that it's not just there for GDB * move TAP events to the TAP chapter, where they belong (bugfix) git-svn-id: svn://svn.berlios.de/openocd/trunk@2013 b42882b7-edfa-0310-969c-e2dbd0fdcd60
* - change signature for adi_jtag_dp_scan and adi_jtag_dp_scan_u32 to use ↵ntfreak2009-06-021-0/+27
| | | | | | | | | | | | | swjdp_common_t *swjdp instead of arm_jtag_t *jtag_info - change SWJDP_IR/DR_APACC to DAP_IR/DR_APACC to conform with ARM_ADI docs. - add swjdp->memaccess_tck field and code for extra tck clocks before accessing memory bus - Set default memaccess value to 8 for Cortex-M3. - Add dap memaccess command. - document all armv7 dap cmds. - Original patch submitted by Magnus Lundin [lundin@mlu.mine.nu]. git-svn-id: svn://svn.berlios.de/openocd/trunk@2005 b42882b7-edfa-0310-969c-e2dbd0fdcd60
* David Brownell <david-b@pacbell.net>:zwelch2009-06-011-42/+22
| | | | | | | | | | | | | | Remove two sections about deprecated/removed commands, documenting them briefly in the chapter on deprecated/removed commands. The "working_area" command just duplicated text; "jtag_device" wasn't listed in that chapter before. Also start de-emphasizing those commands. Don't index them, and include a disclaimer that their documentation may start to vanish about a year after the code does (e.g. in January 2010). git-svn-id: svn://svn.berlios.de/openocd/trunk@1986 b42882b7-edfa-0310-969c-e2dbd0fdcd60
* David Brownell <david-b@pacbell.net>:zwelch2009-06-011-18/+20
| | | | | | | | Uplevel the arch commands to be a chapter; they really don't fit in the "general commands" category. git-svn-id: svn://svn.berlios.de/openocd/trunk@1977 b42882b7-edfa-0310-969c-e2dbd0fdcd60
* David Brownell <david-b@pacbell.net>:zwelch2009-06-011-12/+15
| | | | | | | | | | | | | Fix minor goofage in previous doc updates: * The ETM dummy driver name is "dummy" not "etm_dummy"; re-alphabetize. * DCC trace message mode "charmsg" is a format type (and what Linux needs) git-svn-id: svn://svn.berlios.de/openocd/trunk@1976 b42882b7-edfa-0310-969c-e2dbd0fdcd60
* David Brownell <david-b@pacbell.net>:zwelch2009-06-011-54/+85
| | | | | | | | | | | | | | | | | | | Various updates, mostly small/formatting changes: * Small content tweaks: - Re-title: "OpenOCD User's Guide". - For users, URLS for latest doc and SparkFun forum - Mention GIT-SVN * Fix some front-matter goofage, matching texinfo docs: - "paragraphintent" location matters - put release version/date description with the copyright * Fix some other stuff matching texinfo docs: - no tabs - tweak some refs and anchors * whitespace-at-end-o-line fixes git-svn-id: svn://svn.berlios.de/openocd/trunk@1975 b42882b7-edfa-0310-969c-e2dbd0fdcd60
* Add new JTAG boundary scan primer, with links to BSDL information.zwelch2009-05-311-4/+62
| | | | git-svn-id: svn://svn.berlios.de/openocd/trunk@1954 b42882b7-edfa-0310-969c-e2dbd0fdcd60
* added some comments on meminfo commandoharboe2009-05-301-1/+3
| | | | git-svn-id: svn://svn.berlios.de/openocd/trunk@1948 b42882b7-edfa-0310-969c-e2dbd0fdcd60
* more reset_config textsoharboe2009-05-301-1/+14
| | | | git-svn-id: svn://svn.berlios.de/openocd/trunk@1947 b42882b7-edfa-0310-969c-e2dbd0fdcd60
* David Brownell <david-b@pacbell.net>:zwelch2009-05-301-11/+180
| | | | | | | | | | | | | | | | | Provide basic documentation on the ARM ETM and ETB trace commands. Fix minor goofs in registration of the ETM commands; and whitespace issues in the proof-of-concept oocd_trace code. (Plus include a ref to Dominic's email saying that it's just proof-of-concept code.) Note that I'm still not sure whether the ETM support works. But documenting how it's expected to work should help sort out which behaviors are bugs, which will help get bugs patched. ZW: whitespace changes were split out of this patch but will follow. git-svn-id: svn://svn.berlios.de/openocd/trunk@1945 b42882b7-edfa-0310-969c-e2dbd0fdcd60
* David Brownell <david-b@pacbell.net>:zwelch2009-05-301-18/+57
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Make it so the magic "reset_config" keywords can be provided in any order. This eliminates needless error paths, and makes it easier to define things at the right level (adapter, board, target). It also includes two other behavioral changes: (1) When "handle_reset_config" sees a parameter error, it exits without changing anything. This is best viewed as a bugfix. (Old behavior: restore defaults, even if they weren't previously active.) (2) Only the behaviors that were explicitly specified get changed. (Old behavior: everything else gets reset to the "default".) So for example you can now specify SRST drive requirements without saying anything about the three unrelated topics you previously had to specify. That second one might cause confusion for any configs that end up calling "reset_config" twice, so it will deserve to be called out in the release notes. (There were no such configurations in the current OpenOCD source tree.) Update docs accordingly. Note that at least some versions of the texi-to-html tools can't handle "@xref{with spaces}", but those work properly in PDF and in the info files. git-svn-id: svn://svn.berlios.de/openocd/trunk@1944 b42882b7-edfa-0310-969c-e2dbd0fdcd60
* David Brownell <david-b@pacbell.net>:zwelch2009-05-291-0/+74
| | | | | | | | | | | | | | | | | Provide basic documentation for some of the other flash drivers. avr ... looks incomplete, may work with one AVR8 microcontroller ecosflash ... can't find docs lpc288x ... an NXP part, driver seems lpc2888-specific ocl ... some arm7/arm9 thing, can't find docs pic32mx ... looks incomplete, for PIC32MX (MIPS 4K) devices tms470 ... for TI TMS470 parts Still seems to be mostly arm7tdmi... several of these have no users in the current tree. git-svn-id: svn://svn.berlios.de/openocd/trunk@1941 b42882b7-edfa-0310-969c-e2dbd0fdcd60
* David Brownell <david-b@pacbell.net>:zwelch2009-05-281-151/+367
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Start converting the architecture-specific commands to @deffn format, reviewing against the code. * armv4_5 disassemble ... now documented; although Jazelle code is not handled * It's "armv4_5 core_state" not "core_mode"; although Jazelle state is not handled * arm7/9 "debug" commands ... now with other arm7_9 commands, no longer in a separate section * arm926ejs cp15 ... previous description was broken, it matched the code for arm920t instead * Have separate subsections for ARMv4/ARMv5, ARMv6, and ARMv7; the latter are new * Move core-specific descriptions into sub-subsections under those architectures; XScale and ARM11 descriptions are new The new XScale and ARM11 command descriptions surely need elaboration and review. ARM CP15 operation descriptions in general seem to be confused and incomplete. git-svn-id: svn://svn.berlios.de/openocd/trunk@1939 b42882b7-edfa-0310-969c-e2dbd0fdcd60
* David Brownell <david-b@pacbell.net>:zwelch2009-05-281-79/+167
| | | | | | | | | | | | | | | | | | | | | Continue updating the NOR flash coverage to use @deffn syntax, so the commands have more consistent presentation and formatting. This reorganizes information and updates its presentation, except where the information didn't really match the code. This patch updates the main commands, and finishes making the section structure parallel the NAND presentation. Of note: - The "flash fill[whb] addr value length" commands are now documented. - The "flash bank" command is now presented much earlier - Explicit mention is made that NOR flash should be read using just standard memory access commands, like "mdw" and "dump_image". git-svn-id: svn://svn.berlios.de/openocd/trunk@1938 b42882b7-edfa-0310-969c-e2dbd0fdcd60
* David Brownell <david-b@pacbell.net>:zwelch2009-05-281-210/+315
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Start updating the NOR flash coverage to use @deffn syntax, so the commands have more consistent presentation and formatting. This reorganizes information and updates its presentation, except where the information didn't really match the code. This patch updates most of the driver specific support, creating one new (and alphabetized!) section just for driver-specific data, where previously that data was split over up to three sections. Of note: - The at91sam7 docs were a bit out of date with respect to the code. - The "str9xpec" stuff still deserves some work. For now, it sits in its own subsection; pretty messy. - Likewise the "mflash" stuff. That's a parallel infrastructure, and is now in a section of its own. - The "mass_erase" commands for the Cortex M3 chips got turned into footnotes. IMO, they should vanish sometime; they're superfluous. - There are still a bunch of undocumented NOR drivers. Examples: avr(8), tms470, pic32mx, more. Plus there are a handful of minor tweaks to the NAND docs (to help make the NOR and NAND presentations be parallel); the "Command Index" has been renamed as the "Command and Driver Index"; reference TI instead of Luminary Micro in several places. git-svn-id: svn://svn.berlios.de/openocd/trunk@1937 b42882b7-edfa-0310-969c-e2dbd0fdcd60
* David Brownell <david-b@pacbell.net>:zwelch2009-05-281-81/+108
| | | | | | | | | | | | | | | | | | | | | Fix a bunch of PDF generation bugs in the texi: * The "overfull" warnings are basically complaints about lines that are too long, so they ran off the right margin of the PDF documentation and turn into a "black blot". * The "underfull" warnings are basically complaints about lines that look ugly when they get filled, because the tokens are so long that the line-break algorithm can't do anything good. In a few cases the simplest fix seemed to be to use more appropriate texi commands. In other cases the fix was a content bugfix: "ocd_" not "openocd_"; and many of those "target variants" actually aren't recognized. git-svn-id: svn://svn.berlios.de/openocd/trunk@1936 b42882b7-edfa-0310-969c-e2dbd0fdcd60
* Numerous minor updates and fixes for The Manual:zwelch2009-05-274-3/+5
| | | | | | | | | | - Link Scripting Overview into the TCL Primer; both need more work. - Remove redundant OpenOCD from Scripting Overview subpage title. - Fix incorrect tag in Doxygen style guide example. - Fix minor typo in first introductory paragraph of main page. git-svn-id: svn://svn.berlios.de/openocd/trunk@1932 b42882b7-edfa-0310-969c-e2dbd0fdcd60
* unsik Kim <donari75@gmail.com>:zwelch2009-05-271-3/+17
| | | | | | | Add mflash configuration code, updating relevant documentation. git-svn-id: svn://svn.berlios.de/openocd/trunk@1930 b42882b7-edfa-0310-969c-e2dbd0fdcd60
* unsik Kim <donari75@gmail.com>:zwelch2009-05-271-10/+7
| | | | | | | Remove unused mflash bank command options. git-svn-id: svn://svn.berlios.de/openocd/trunk@1928 b42882b7-edfa-0310-969c-e2dbd0fdcd60
* - add support for cortino jtag interfacentfreak2009-05-271-0/+4
| | | | git-svn-id: svn://svn.berlios.de/openocd/trunk@1925 b42882b7-edfa-0310-969c-e2dbd0fdcd60
* Add new Style Guides for languages used (and to be used) by project.zwelch2009-05-271-19/+212
| | | | git-svn-id: svn://svn.berlios.de/openocd/trunk@1924 b42882b7-edfa-0310-969c-e2dbd0fdcd60
* Link new Primer pages into the main list of Primers.zwelch2009-05-271-0/+2
| | | | git-svn-id: svn://svn.berlios.de/openocd/trunk@1923 b42882b7-edfa-0310-969c-e2dbd0fdcd60
* Add Documentation Primer to The Manual.zwelch2009-05-271-0/+122
| | | | git-svn-id: svn://svn.berlios.de/openocd/trunk@1922 b42882b7-edfa-0310-969c-e2dbd0fdcd60
* Add draft of Autotools Primer to The Manual.zwelch2009-05-271-0/+167
| | | | git-svn-id: svn://svn.berlios.de/openocd/trunk@1921 b42882b7-edfa-0310-969c-e2dbd0fdcd60
* David Brownell <david-b@pacbell.net>:zwelch2009-05-261-61/+127
| | | | | | | | | | | | | | | | | | Update the "Reset Configuration" information in the User's guide: - Convert to @deffn syntax - Move tutorial text from command descriptions into new sections - Describe several different types of JTAG-visible reset - Expand descriptions of configuration tweaks for SRST and TRST - Link to the "reset" command, and vice versa - Bugfix the "reset_config" description (it didn't match the code) Plus, be more proscriptive: do it in board config files, except for the oddball cases where that won't work. (Current target.cfg files seem to have much goofage there; several seem board-specific.) git-svn-id: svn://svn.berlios.de/openocd/trunk@1913 b42882b7-edfa-0310-969c-e2dbd0fdcd60
* David Brownell <david-b@pacbell.net>:zwelch2009-05-241-44/+64
| | | | | | | | | | | | | | | Doc (mostly) update for jtag_khz: - switch to @deffn syntax - add entry for "jtag_rclk" - move deprecated "jtag_speed" into collection of deprecated calls And for ft2232, don't be the only adapter to *log* an error if RTCK is requested; it's already reported properly, like any other nonfatal command parameter. "jtag_rclk" just works as expected, without any scarey messages. git-svn-id: svn://svn.berlios.de/openocd/trunk@1910 b42882b7-edfa-0310-969c-e2dbd0fdcd60
* David Brownell <david-b@pacbell.net>:zwelch2009-05-241-57/+100
| | | | | | | | | | | | | | | | | | | | | | | Make startup for the various server ports be quiet, unless debugging is active: don't emit needless scarey messages. Update the relevant documentation and its references: - For these port commands ... cover the default values; convert to @deffn syntax; include their use outside of the configuration stage; and alphabetize. Similar updates to the rest of that small chapter: - Highlight that there even *IS* a configuration stage, after which some command functionality is no longer available. - For GDB commands ... convert to @deffn syntax; alphabetize; include a missing command (!); add missing helptext (!) for one non-missing command; update relevant cross-references and index entries. git-svn-id: svn://svn.berlios.de/openocd/trunk@1909 b42882b7-edfa-0310-969c-e2dbd0fdcd60
* David Brownell <david-b@pacbell.net>:zwelch2009-05-241-4/+33
| | | | | | | | | | | | | | | | | | | | | | | | | Update two oddball NAND commands to work with {offset, length} instead of block numbers, matching the other commands as well as usage in U-Boot and the Linux-MTD utilities. Document them accordingly. Update the single in-tree use of those commands (sheevaplug). ALSO: (a) Document the current 2 GByte/chip ceiling for NAND chipsize. (32 bit offset/length values can't represent 4 GBytes.) Maybe after the upcoming release, the code can switch to 64-bits. (b) The "nand check_bad_blocks" should report "bad" blocks. They are not "invalid" blocks; they're "bad" ones. (c) Tweak the "nand info" command to handle the "no arguments" case sanely (show everything, instead of showing garbage) and not listing the blocksize in hex kbytes (duh). git-svn-id: svn://svn.berlios.de/openocd/trunk@1904 b42882b7-edfa-0310-969c-e2dbd0fdcd60
* David Brownell <david-b@pacbell.net>:zwelch2009-05-241-0/+17
| | | | | | | | | | | | | | | | | | NAND support for DaVinci-family drivers, with HW ECC support. Declare the NAND chip on the DM355 EVM board. Currently tested on DM355 for Linux interop using the standard large page (2KB) chip in the EVM socket; "hwecc1" and "hwecc4" work fine. (Using hwecc4 relies on patches that haven't quite made it through the Linux-MTD bottlenecks yet.) Not yet tested: 1-bit on small-page (although it's hard to see how that could fail); 4-bit on small page (picky layout issues); the "hwecc_infix" mode (primarily for older boot ROMs; testing there is blocked on having new bootloader code). git-svn-id: svn://svn.berlios.de/openocd/trunk@1903 b42882b7-edfa-0310-969c-e2dbd0fdcd60
* Fix two problems with openocd.texi:zwelch2009-05-241-5/+5
| | | | | | | | - Fix minor issues with xrefs not liking parentheses around them. - Change 'Building' section to 'Building OpenOCD'. It reads better. git-svn-id: svn://svn.berlios.de/openocd/trunk@1902 b42882b7-edfa-0310-969c-e2dbd0fdcd60
* Add section identifiers to developer scripting introduction.zwelch2009-05-231-3/+3
| | | | git-svn-id: svn://svn.berlios.de/openocd/trunk@1898 b42882b7-edfa-0310-969c-e2dbd0fdcd60
* Update main page of doxygen developer documentation:zwelch2009-05-231-8/+25
| | | | | | | | - Rewrite copy to give a better introduction and overview. - Add subpages: The List, Style Guide, Patch Policies, and Bug Reporting. git-svn-id: svn://svn.berlios.de/openocd/trunk@1897 b42882b7-edfa-0310-969c-e2dbd0fdcd60
* Add extended doxygen-based style guide draft; requires more work.zwelch2009-05-231-0/+93
| | | | git-svn-id: svn://svn.berlios.de/openocd/trunk@1896 b42882b7-edfa-0310-969c-e2dbd0fdcd60
* Update user guide documentation:zwelch2009-05-231-45/+65
| | | | | | | | | - Remove style guide from user guide; moved to doxygen manual. - Replace with improved introduction for developers and packagers. - Move introductory paragraph about the project under the About page. git-svn-id: svn://svn.berlios.de/openocd/trunk@1895 b42882b7-edfa-0310-969c-e2dbd0fdcd60
* Submitted by David Brownell <david-b@pacbell.net>:zwelch2009-05-221-12/+317
| | | | | | | | | | | | | | | | | | Add a "NAND Commands" section to to the TEXI docs, covering the basic commands except for those previously discussed as being due for removal ("nand copy") or switching to use byte offsets not block numbers. This uses the "@deffn..." syntax for defining commands, as somewhat suggested by the TEXI documentation, and adds a new "Command Index". We might prefer to merge those indexes for the near term, but I think the "@deffn" approch is probably worth switching to. Updates a few other bits to clarify that "flash" doesn't just mean NOR. And to fix one niggling falsity: the "reset-init" event *is* used, and in fact it's quite important. git-svn-id: svn://svn.berlios.de/openocd/trunk@1879 b42882b7-edfa-0310-969c-e2dbd0fdcd60
* Add initial OpenOCD server documentation (Duane Ellis and myself).zwelch2009-05-201-1/+287
| | | | git-svn-id: svn://svn.berlios.de/openocd/trunk@1857 b42882b7-edfa-0310-969c-e2dbd0fdcd60
* Add new TCL Primer under the main Technical Primer page.zwelch2009-05-201-0/+1
| | | | git-svn-id: svn://svn.berlios.de/openocd/trunk@1856 b42882b7-edfa-0310-969c-e2dbd0fdcd60
* Move TCL overview from source tree to doxygen manual.zwelch2009-05-201-0/+438
| | | | git-svn-id: svn://svn.berlios.de/openocd/trunk@1855 b42882b7-edfa-0310-969c-e2dbd0fdcd60
* Fix doc/Makefile.am dist-hook to include all sections of manual.zwelch2009-05-201-0/+4
| | | | git-svn-id: svn://svn.berlios.de/openocd/trunk@1854 b42882b7-edfa-0310-969c-e2dbd0fdcd60
* Move non-arm target overview from source tree to doxygen manual.zwelch2009-05-202-6/+71
| | | | git-svn-id: svn://svn.berlios.de/openocd/trunk@1853 b42882b7-edfa-0310-969c-e2dbd0fdcd60
* Move scripting overview from source tree to doxygen manual.zwelch2009-05-201-0/+80
| | | | git-svn-id: svn://svn.berlios.de/openocd/trunk@1852 b42882b7-edfa-0310-969c-e2dbd0fdcd60
* Wookey <wookey@wookware.org>: add user documentation for echo command.zwelch2009-05-191-0/+4
| | | | git-svn-id: svn://svn.berlios.de/openocd/trunk@1839 b42882b7-edfa-0310-969c-e2dbd0fdcd60
* Relocate documentation on working area to better align with use of new ↵kc8apf2009-05-181-13/+14
| | | | | | syntax. Provided by David Brownell <david-b@pacbell.net> git-svn-id: svn://svn.berlios.de/openocd/trunk@1806 b42882b7-edfa-0310-969c-e2dbd0fdcd60
* Consolidate target selection code into single get_target() that handles both ↵kc8apf2009-05-181-21/+26
| | | | | | names and numbers. Provided by David Brownell <david-b@pacbell.net> git-svn-id: svn://svn.berlios.de/openocd/trunk@1804 b42882b7-edfa-0310-969c-e2dbd0fdcd60
generated by cgit v1.2.3 (git 2.46.0) at 2024-12-24 18:10:53 +0000