summaryrefslogtreecommitdiff
path: root/src
Commit message (Collapse)AuthorAgeFilesLines
...
* cfi: fix gaffe introduced in previous versionØyvind Harboe2010-06-141-2/+2
| | | | | | | | flash probe broke w/in last commit. ecc8041c0f4c30a7310c0f8414a5261ee7a090ca Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
* target: fix retval gaffe in mwX commandsØyvind Harboe2010-06-141-1/+1
| | | | | | | | | | | failure to write to memory was not propagated. This is an interesting case of broken error handling: with exceptions we wouldn't have had this at all, and I also wonder if there is a GCC option to warn about these kinds of potential bugs. Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
* TARGET: removed unused parametersAntonio Borneo2010-06-127-27/+8
| | | | | | | Parameters "domain" and "ap" of function armv4_5_mmu_translate_va() are not used. Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
* TARGET: removed unsed parameterAntonio Borneo2010-06-127-25/+11
| | | | | | | | Parameter "type" of function armv4_5_mmu_translate_va() is now not used. Remove the parameter and the "enum" listing its values. Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
* TARGET: fix handling return code of MMU translationAntonio Borneo2010-06-126-26/+0
| | | | | | | | | Function armv4_5_mmu_translate_va() now properly signals errors in the return value. Remove former error handling by setting variable "type" to value "-1". Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
* TARGET/ARM920T: fix return valueAntonio Borneo2010-06-121-1/+1
| | | | | | | | | Function arm920t_write_memory() default return value should be ERROR_OK. All cases of local errors are handled immediately and not further propagated. Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
* TARGET/ARM920T: fix compile warningAntonio Borneo2010-06-121-1/+1
| | | | | | | | | Commit 0538081246fafbfb74d554bb1b758412534aa254 introduces a compile time warning: arm920t.c: In function ‘arm920t_write_memory’: arm920t.c:567: warning: ‘retval’ may be used uninitialized in this function Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
* flash: add error handling to get_flash_by_addr/nameØyvind Harboe2010-06-113-25/+38
| | | | | | | autoprobing can fail and this error has to be reported up the call stack. Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
* arm mmu: error propagation added for address translationØyvind Harboe2010-06-117-19/+47
| | | | | | | The return value for MMU translation was a mess, either error or value. Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
* cfi: fix error propagationØyvind Harboe2010-06-112-118/+341
| | | | | | | | | | any read/write operation to memory can fail. block write algorithm error propagation was broken in that it would continue after an error was reported writing data to ram or the algorithm failing. Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
* jtag: added mising headerThomas Koeller2010-06-101-0/+1
| | | | | | | Distributions created by 'make dist' were incomplete due to a missing header file. Signed-off-by: Thomas Koeller <thomas.koeller@baslerweb.com>
* flash: add error message if image is too big for flashØyvind Harboe2010-06-091-1/+5
| | | | | | | replaced assert() w/error message if the image is too big. Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
* flash: flash erase_address takes unsigned argumentsØyvind Harboe2010-06-091-4/+4
| | | | | | | fixed bug where address was parsed as a signed, rather than unsigned it. Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
* zy1000: fix optimisation gaffeØyvind Harboe2010-06-081-7/+30
| | | | | | DCC optimisation was broken on targets w/multiple TAP's. Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
* zy1000: added watchdog serverØyvind Harboe2010-06-081-1/+92
| | | | Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
* cfi: fix GDB keep alive bugØyvind Harboe2010-06-081-0/+2
| | | | | | Long running CFI writes could cause GDB timeout. Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
* verify: display up to 128 diff'sØyvind Harboe2010-06-081-11/+19
| | | | | | Showing up to 128 differences. Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
* gdb-server: fix error reporting bugsØyvind Harboe2010-06-081-24/+9
| | | | | | | | | | | | GDB and OpenOCD has two different error number spaces and no mapping exists between them. If a specific error number is to be reported to GDB then this has to be done at the calling site, rather than as a generic routine that tries to map "retval" to GDB error number speak. Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
* jtag: rename JTAG_MOVESTATE to JTAG_TLR_RESETØyvind Harboe2010-06-0713-14/+21
| | | | | | | | | JTAG_MOVESTATE is misleading, this cmd is only used for reset. JTAG_PATHMOVE should be used otherwise. Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
* stm32 : change returned value of mass_erase functiongcembed2010-06-031-4/+5
| | | | | | | | | | | | | | Hello, "stm32x mass_erase" return ERROR_OK even if something goes wrong. Here is a summary of changes : * in stm32x_mass_erase : return ERROR_FLASH_OPERATION_FAILED when error detected in FLASH_SR register; * in COMMAND_HANDLER(stm32x_handle_mass_erase_command) : return the returned value of stm32x_mass_erase(). I don't know if there is reason to always return ERROR_OK ? Gaëtan
* etm: print something when trace buffer emptyJon Povey2010-05-311-0/+5
| | | | | | | | ETM analyze produced no output when the trace buffer was empty. This patch provides users with a clue. Signed-off-by: Jon Povey <jon.povey@racelogic.co.uk> Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
* nor: fix memory leaks during probeSpencer Oliver2010-05-295-0/+30
| | | | | | | Fix similar memory leaks as per commit: ef72484b785ec7462a0415afea679d08b864c7fb Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
* flash: virtual driver update for get_flash_bank_by_name_noprobeSpencer Oliver2010-05-261-2/+2
| | | | | | Make sure we do not probe a flash when getting info. Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
* nor: add get_flash_bank_by_name autoprobeSpencer Oliver2010-05-263-4/+32
| | | | | | | | | | | When a flash cmd is called using the flash name the autoprobe function is not called. autoprobe is called if flash_command_get_bank falls through to get_flash_bank_by_num. This makes both get_flash_bank_by_name and get_flash_bank_by_num behave the same. Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
* flash: add virtual flash bank driverSpencer Oliver2010-05-263-1/+248
| | | | | | | | | | | | | This adds a virtual flash bank driver that allows virtual banks to be defined that refer to an existing flash bank. For example the real address for bank0 on the pic32 is 0x1fc00000 but the user program will either be in kseg0 (0xbfc00000) or kseg1 (0x9fc00000). This also means that gdb will be aware of all the read only flash addresses. Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
* NOR/CFI: fix memory leak; check malloc return valueAntonio Borneo2010-05-261-3/+48
| | | | | | | | | | | Every time command "flash probe #" is executed, memory structures are re-allocated without preventive free() of former areas, causing memory leak. Also, memory allocation does not check return value, determining segmentation fault in case of out of memory. Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com> Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
* arm_adi_v5: correct ahbap_debugport_init mem-ap id (bug #23)Spencer Oliver2010-05-211-0/+3
| | | | | | | | We request a id register read at the end of ahbap_debugport_init but we never actually run the queue. In some cases this causes a segfault. Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
* nand : Add Freescale iMX27 nand flash controller supportgcembed2010-05-204-0/+900
| | | | | | | | This patch add support of iMX27 nand flash controller. This is based on driver for imx31 nand flash controller. OOB functionality is not fully working. As in mx31 controller, mx2 NFC has a bug that swap two bytes between SPARE and MAIN buffer. I used this driver for several months and no problems appear.
* target: slow targets could cause GDB to time outGary Carlson2010-05-191-1/+40
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This second half of the patch is proposed to clean up some GDB keep alive issues on arm7_9 targets that start up with very slow clocks. If an attempt is made to write to key registers on the processor with a slow jtag speed, GDB timeout warnings appear on the console (at least mine) when "reset halt" or "reset init" commands are issued from the gdb client: *** BEFORE PATCH *** (gdb) monitor reset init fast memory access is disabled 2 kHz keep_alive() was not invoked in the 1000ms timelimit. GDB alive packet not sent! (1026). Workaround: increase "set remotetimeout" in GDB JTAG tap: at91sam9g20.cpu tap/device found: 0x0792603f (mfg: 0x01f, part: 0x7926, ver: 0x0) target state: halted target halted in ARM state due to breakpoint, current mode: Supervisor cpsr: 0x000000d3 pc: 0x00000000 MMU: disabled, D-Cache: disabled, I-Cache: disabled keep_alive() was not invoked in the 1000ms timelimit. GDB alive packet not sent! (1027). Workaround: increase "set remotetimeout" in GDB keep_alive() was not invoked in the 1000ms timelimit. GDB alive packet not sent! (1006). Workaround: increase "set remotetimeout" in GDB keep_alive() was not invoked in the 1000ms timelimit. GDB alive packet not sent! (1006). Workaround: increase "set remotetimeout" in GDB keep_alive() was not invoked in the 1000ms timelimit. GDB alive packet not sent! (1006). Workaround: increase "set remotetimeout" in GDB keep_alive() was not invoked in the 1000ms timelimit. GDB alive packet not sent! (1004). Workaround: increase "set remotetimeout" in GDB RCLK - adaptive dcc downloads are enabled fast memory access is enabled NAND flash device 'NAND 256MiB 3,3V 8-bit' found (gdb) I added additional keep alive steps in areas that troubleshooting revealed were causing problems. I only did this however for non-fast write memory accesses. I don't think most people would be using fast memory accesses to write to memory when the jtag and system clocks are slow anyway. If you disagree with my feeling, think there is a more elegant way to handle the problem, or think the patch will cause other unforeseen problems with other targets, let me know. As you can see below, the patch does eliminate the problem on my development station and I suspect that it will benefit others. *** AFTER PATCH *** (gdb) monitor reset init fast memory access is disabled 2 kHz JTAG tap: at91sam9g20.cpu tap/device found: 0x0792603f (mfg: 0x01f, part: 0x7926, ver: 0x0) target state: halted target halted in ARM state due to breakpoint, current mode: Supervisor cpsr: 0x000000d3 pc: 0x00000000 MMU: disabled, D-Cache: disabled, I-Cache: disabled RCLK - adaptive dcc downloads are enabled fast memory access is enabled NAND flash device 'NAND 256MiB 3,3V 8-bit' found (gdb) Gary Carlson Gary Carlson, MSEE Principal Engineer Carlson-Minot Inc.
* jim: fix bug in tcl "puts"Øyvind Harboe2010-05-181-9/+4
| | | | | | | | | | | | tcl "puts" didn't work because the logging code sensored strings that did not include a '\n'. The correct thing is to sensor empty strings, which are used to keep gdb connection alive. The tcl "puts" code broke apart strings which do contain '\n' in order to implement the -nonewline argument, which is how it got hurt by the bug in log.c Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
* zy1000: fix false positive warning about unitialized local variableØyvind Harboe2010-05-181-1/+1
| | | | Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
* NAND/davinci: Fix segfault for hwecc4_infix readsJon Povey2010-05-181-12/+62
| | | | | | | | | | | | | | | | | | | | Page reads using hwecc4_infix layout segfaulted for check_bad_blocks because the read assumed a valid data buffer, which check_bad_blocks does not use (it only passes a 6 byte buffer for the start of OOB). This version copes with undersized or missing data or oob buffers and uses random read commands within the page to skip unwanted areas of data/OOB for speed. NOTE: Running check_bad_blocks with this layout will be reading infix OOB locations, not manufacturer bad block markers. This means that if you check blocks written in infix layout they will appear good, but manufacturer- marked bad blocks may also appear good. If you want to scan for manufactuer-marked bad blocks, you need to enable raw_access before running check_bad_blocks, or use the non-infix layout. Signed-off-by: Jon Povey <jon.povey@racelogic.co.uk> CC: David Brownell <dbrownell@users.sourceforge.net>
* NAND: catch read errors when building BBTJon Povey2010-05-181-1/+4
| | | | | | | | nand_build_bbt() was ignoring the return value from nand_read_page() and blindly continuing. It now passes the return value up to the caller if the read fails. Signed-off-by: Jon Povey <jon.povey@racelogic.co.uk>
* gdbserver: gdb cmds returning failure on successSpencer Oliver2010-05-171-9/+12
| | | | | | | The gdb_memory_map cmd for example fell through and returned ERROR_COMMAND_SYNTAX_ERROR on success - behaviour is now as expected. Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
* Change kb/s to KiB/s in messages about kibibytesJon Povey2010-05-163-11/+11
| | | | | | | Change download rate messages about kibibytes from "kb/s" to "KiB/s" units. See: http://en.wikipedia.org/wiki/Data_rate_units Signed-off-by: Jon Povey <jon.povey@racelogic.co.uk>
* NOR/CFI: minor code cleanupAntonio Borneo2010-05-161-8/+0
| | | | | | | Remove few LOG_DEBUG() messages, together with code and variables required to build such messages. Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
* NOR/CFI: add cfi_read() implementationAntonio Borneo2010-05-161-2/+72
| | | | | | | | | | Final step to force bus_width size during CFI flash read. Added CFI specific implementation cfi_read() that uses only accesses at bus_width size. Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
* NOR: add read() callback to struct flash_driverAntonio Borneo2010-05-1623-1/+72
| | | | | | | | | | | | | | Final target is to force bus_width size during CFI flash read. In this first step I need to replace default flash read with flash specific implementation. This patch introduces: - flash_driver_read() layer; - default_flash_read(), backward compatible; - read() callback in struct flash_driver; - proper initialization in every flash_driver instance. Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
* NOR/TCL: fix typo in error messageAntonio Borneo2010-05-161-1/+1
| | | | Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
* NOR: fix comment for DoxygenAntonio Borneo2010-05-161-2/+3
| | | | | | Either bus_width and chip_width are in bytes. Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
* NOR/CFI: remove use of cfi_add_byte()Antonio Borneo2010-05-161-40/+1
| | | | | | | Remove the function cfi_add_byte() and rewrite the only instance of it. Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
* NOR/CFI: use bus_width for memory access in cfi_write()Antonio Borneo2010-05-161-54/+15
| | | | | | | | | | | | | | During cfi_write(), head and tail of destination area could be not aligned to bus_width. Since write operation must be at bus_width size, source buffer size is extended and buffer padded with current values read from flash. Force using bus_width to read current value from flash. Do not use cfi_add_byte() anymore, to allow removing this function later on. Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
* NOR/CFI: use bus_width for memory access on flash ID.Antonio Borneo2010-05-161-25/+22
| | | | | | | | | | NOR flash structure requires each access to be bus_width wide. Fix read of flash ID accordingly to rule above. Add case (chip_width == 4), allowed by CFI spec and coherent with current value of CFI_MAX_CHIP_WIDTH but currently not used by any target. Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
* NOR/CFI: identify memory accesses not using "bus_width".Antonio Borneo2010-05-161-0/+8
| | | | | | | | | | | | | | | | | | | | Since NOR flash devices does not handle "byte enable lanes", each read/write access involves the whole "chip_width". When multiple devices are in parallel, usually all chips are enabled during each access. All such cases are compatible with flash accesses at "bus_width" size. Access at "bus_width" size is mandatory for write access to avoid transferring of garbage values to flash. During read access the flash controller should take care, and discard unneeded bytes. Anyway, it is good practice to use "bus_width" size also for read. Every memory access that does not respect "bus_width" size is marked with a "FIXME" comment. Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
* NOR/CFI: simplify bufferwsize computationAntonio Borneo2010-05-161-39/+10
| | | | | | | | | | | | | | | | | | | | | | | | | Review and simplify computation of bufferwsize. Add comments about variables' meaning. The same code is present 3 times in the file. Current patch updates all the 3 instances. Step 1) Replace "switch(bank->chip_width) {...}". Illegal values of bank->chip_width are already dropped. For legal values, the code is equivalent to: bufferwsize = buffersize / bank->chip_width; Step 2) The above code replacement plus the following line: bufferwsize /= (bank->bus_width / bank->chip_width); is merged in a single formula: bufferwsize = (buffersize / bank->chip_width) / (bank->bus_width / bank->chip_width); and simplified as: bufferwsize = buffersize / bank->bus_width; Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
* NOR/CFI: check "flash bank" command argumentsAntonio Borneo2010-05-161-1/+11
| | | | | | | | | | | | | | | | | | Arguments chip_width and bus_width of command "flash bank" are not fully checked. While bus_width is later on redundantly checked in several other parts (e.g. in cfi_command_val()) and generates run-time error, chip_width is never checked, nor related to actual bus_width value. Added check to avoid: - (chip_width == 0), that would mean no memory chip at all, avoiding also division by zero e.g. in cfi_get_u8(); - (bus_width == 0), that would mean no bus at all; - unsupported cases of chip_width or bus_width value not power of 2; - unsupported case of chip width wider than bus. Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
* missing pointer's declaration when enable macro -D_DEBUG_GDB_IO_.Jun Ma2010-05-141-0/+3
| | | | | | | reproducable when "./configure --enable-maintainer-mode CFLAGS=-D_DEBUG_GDB_IO_" Signed-off-by: Jun Ma <sync.jma@gmail.com> Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
* NAND: fix first and last handling in nand_build_bbtJon Povey2010-05-141-3/+5
| | | | | | | | | | Last block was being skipped, fix by changing the loop test from "<" to "<=" First block argument was ignored, always started from block 0 (and counted the wrong blocks as bad if first was nonzero). Now we use it. Signed-off-by: Jon Povey <jon.povey@racelogic.co.uk> Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
* NAND: fix off-by-one error in erase command argument rangeJon Povey2010-05-141-1/+1
| | | | | | | | | The last_block argument to nand_erase() is checked against nand->num_blocks, but the highest valid block number is (total - 1), the test for invalid should be ">=" rather than ">". Signed-off-by: Jon Povey <jon.povey@racelogic.co.uk> Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
* flash: require unique flash bank nameSpencer Oliver2010-05-131-0/+8
| | | | | | Make sure the flash bank name is unique Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>