From 40f361dd944803e500169337fffe7713842fd632 Mon Sep 17 00:00:00 2001
From: oharboe <oharboe@b42882b7-edfa-0310-969c-e2dbd0fdcd60>
Date: Sat, 12 Sep 2009 08:11:45 +0000
Subject: David Brownell <david-b@pacbell.net> Update the board config for the
 DaVinci DM355 EVM so the reset-init event handler does the rest of the work
 it should do:

 - minor PLL setup bugfixes
 - initialize the DDR2 controller
 - probe both NAND banks
 - initialize UART0
 - enable the icache


git-svn-id: svn://svn.berlios.de/openocd/trunk@2699 b42882b7-edfa-0310-969c-e2dbd0fdcd60
---
 tcl/board/dm355evm.cfg | 87 ++++++++++++++++++++++++++++++++++++++++++++++++--
 1 file changed, 84 insertions(+), 3 deletions(-)

(limited to 'tcl/board')

diff --git a/tcl/board/dm355evm.cfg b/tcl/board/dm355evm.cfg
index 9b32ef9e..bb745005 100644
--- a/tcl/board/dm355evm.cfg
+++ b/tcl/board/dm355evm.cfg
@@ -35,7 +35,7 @@ proc dm355evm_init {} {
 	set addr [dict get $dm355 pllc1]
 	set pll_divs [dict create]
 	dict set pll_divs div3 16
-	dict set pll_divs div4 8
+	dict set pll_divs div4 4
 	pll_v02_setup $addr 144 $pll_divs
 
 	# ARM is now running at 216 MHz, so JTAG can go faster
@@ -48,6 +48,7 @@ proc dm355evm_init {} {
 
 	set addr [dict get $dm355 pllc2]
 	set pll_divs [dict create]
+	dict set pll_divs div1 1
 	dict set pll_divs prediv 8
 	pll_v02_setup $addr 114 $pll_divs
 
@@ -77,7 +78,54 @@ proc dm355evm_init {} {
 	########################
 	# DDR2 EMIF
 
-	# FIXME setup
+	# VTPIOCR impedance calibration
+	set addr [dict get $dm355 sysbase]
+	set addr [expr $addr + 0x70]
+
+	# clear CLR, LOCK, PWRDN; wait a clock; set CLR
+	mmw $addr 0 0x20c0
+	mmw $addr 0x2000 0
+
+	# wait for READY
+        while { [expr [mrw $addr] & 0x8000] == 0 } { sleep 1 }
+
+	# set IO_READY; then LOCK and PWRSAVE; then PWRDN
+	mmw $addr 0x4000 0
+	mmw $addr 0x0180 0
+	mmw $addr 0x0040 0
+
+	# NOTE:  this DDR2 initialization sequence borrows from
+	# both UBL 1.50 and the SPRUEH7D DDR2 EMIF spec.
+
+	# reset (then re-enable) DDR controller
+	psc_reset 13
+	psc_go
+	psc_enable 13
+	psc_go
+
+	# now set it up for Micron MT47H64M16HR-37E @ 171 MHz
+
+	set addr [dict get $dm355 ddr_emif]
+
+	# DDRPHYCR1
+	mww [expr $addr + 0xe4] 0x50006404
+
+	# PBBPR -- burst priority
+	mww [expr $addr + 0x20] 0xfe
+
+	# SDCR -- unlock boot config; init for DDR2, relock, unlock SDTIM*
+	mmw [expr $addr + 0x08] 0x00800000 0
+	mmw [expr $addr + 0x08] 0x0013c632 0x03870fff
+
+	# SDTIMR, SDTIMR2
+	mww [expr $addr + 0x10] 0x2a923249
+	mww [expr $addr + 0x14] 0x4c17c763
+
+	# SDCR -- relock SDTIM*
+	mmw [expr $addr + 0x08] 0 0x00008000
+
+	# SDRCR -- refresh rate (171 MHz * 7.8usec)
+	mww [expr $addr + 0x0c] 1336
 
 	########################
 	# ASYNC EMIF
@@ -98,10 +146,43 @@ proc dm355evm_init {} {
 	# NANDFCR -- only CS0 has NAND
 	mww [expr $addr + 0x60] 0x01
 
+	# default: both chipselects to the NAND socket are used
+	nand probe 0
+	nand probe 1
+
 	########################
 	# UART0
 
-	# FIXME setup
+	set addr [dict get $dm355 uart0]
+
+	# PWREMU_MGNT -- rx + tx in reset
+	mww [expr $addr + 0x30] 0
+
+	# DLL, DLH -- 115200 baud
+	mwb [expr $addr + 0x20] 0x0d
+	mwb [expr $addr + 0x24] 0x00
+
+	# FCR - clear and disable FIFOs
+	mwb [expr $addr + 0x08] 0x07
+	mwb [expr $addr + 0x08] 0x00
+
+	# IER - disable IRQs
+	mwb [expr $addr + 0x04] 0x00
+
+	# LCR - 8-N-1
+	mwb [expr $addr + 0x0c] 0x03
+
+	# MCR - no flow control or loopback
+	mwb [expr $addr + 0x10] 0x00
+
+	# PWREMU_MGNT -- rx + tx normal, free running during JTAG halt
+	mww [expr $addr + 0x30] 0xe001
+
+
+	########################
+
+	# turn on icache - set I bit in cp15 register c1
+	arm926ejs cp15 0 0 1 0 0x00051078
 }
 
 # NAND -- socket has two chipselects, MT29F16G08FAA puts 1GByte on each one.
-- 
cgit v1.2.3