From 3878b1279399cbd1c57730f7410db4b7c01b15c4 Mon Sep 17 00:00:00 2001
From: oharboe <oharboe@b42882b7-edfa-0310-969c-e2dbd0fdcd60>
Date: Wed, 2 Sep 2009 17:34:35 +0000
Subject: David Claffey <dnclaffey@gmail.com> tested with the Atheros reference
 design "PB44"

git-svn-id: svn://svn.berlios.de/openocd/trunk@2662 b42882b7-edfa-0310-969c-e2dbd0fdcd60
---
 tcl/target/ar71xx.cfg | 56 +++++++++++++++++++++++++++++++++++++++++++++++++++
 1 file changed, 56 insertions(+)
 create mode 100644 tcl/target/ar71xx.cfg

(limited to 'tcl')

diff --git a/tcl/target/ar71xx.cfg b/tcl/target/ar71xx.cfg
new file mode 100644
index 00000000..f2f5289b
--- /dev/null
+++ b/tcl/target/ar71xx.cfg
@@ -0,0 +1,56 @@
+# Atheros AR71xx MIPS 24Kc SoC.
+# tested on PB44 refererence board
+
+jtag_nsrst_delay 100
+jtag_ntrst_delay 100
+
+reset_config trst_and_srst
+
+set CHIPNAME ar71xx
+
+jtag newtap $CHIPNAME cpu -irlen 5 -ircapture 0x1 -irmask 0x1f -expected-id 1
+
+set TARGETNAME [format "%s.cpu" $CHIPNAME]
+target create $TARGETNAME mips_m4k -endian big -chain-position $TARGETNAME
+
+$TARGETNAME configure -event reset-init {
+	#setup PLL to lowest common denominator 300/300/150 setting
+	mww 0xb8050000 0x000f40a3	# reset val + CPU:3 DDR:3 AHB:0
+	mww 0xb8050000 0x800f40a3	# send to PLL
+
+	#next command will reset for PLL changes to take effect
+	mww 0xb8050008 3		# set reset_switch and clock_switch (resets SoC)
+	reset halt     			# let openocd know that it is in the reset state
+
+	#initialize_pll
+	mww 0xb8050000 0x800f0080	# set sw_update bit
+	mww 0xb8050008 0		# clear reset_switch bit
+	mww 0xb8050000 0x800f00e8       # clr pwrdwn & bypass
+	mww 0xb8050008 1		# set clock_switch bit
+	sleep 1                         # wait for lock
+	
+	# Setup DDR config and flash mapping
+	mww 0xb8000000 0xefbc8cd0       # DDR cfg cdl val (rst: 0x5bfc8d0)
+	mww 0xb8000004 0x8e7156a2       # DDR cfg2 cdl val (rst: 0x80d106a8)
+	
+	mww 0xb8000010 8		# force precharge all banks
+	mww 0xb8000010 1 		# force EMRS update cycle
+	mww 0xb800000c 0                # clr ext. mode register
+	mww 0xb8000010 2 		# force auto refresh all banks
+	mww 0xb8000010 8		# force precharge all banks
+	mww 0xb8000008 0x31             # set DDR mode value CAS=3
+	mww 0xb8000010 1 		# force EMRS update cycle
+	mww 0xb8000014 0x461b           # DDR refresh value
+	mww 0xb8000018 0xffff           # DDR Read Data This Cycle value (16bit: 0xffff)
+	mww 0xb800001c 0x7              # delay added to the DQS line (normal = 7)
+	mww 0xb8000020 0
+	mww 0xb8000024 0
+	mww 0xb8000028 0
+}	
+
+# setup working area somewhere in RAM
+$TARGETNAME configure -work-area-phys 0xa0600000 -work-area-size 0x20000
+
+# serial SPI capable flash
+# flash bank <driver> <base> <size> <chip_width> <bus_width>
+
-- 
cgit v1.2.3