| ID |
Target |
Interface |
Description |
Initial state |
Input |
Expected output |
Actual output |
Pass/Fail |
| RES001 |
LPC2148 |
ZY1000 |
Reset halt on a blank target |
Erase all the content of the flash |
Connect via the telnet interface and type
reset halt |
Reset should return without error and the output should contain
target state: halted |
> mdw 0 32
0x00000000: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff
0x00000020: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff
0x00000040: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff
0x00000060: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff
> reset halt
JTAG tap: lpc2148.cpu tap/device found: 0x4f1f0f0f (mfg: 0x787, part: 0xf1f0, ver: 0x4)
srst pulls trst - can not reset into halted mode. Issuing halt after reset.
target state: halted
target halted in Thumb state due to debug-request, current mode: Supervisor
cpsr: 0xa00000f3 pc: 0x7fffd2d6
>
|
PASS |
| RES002 |
LPC2148 |
ZY1000 |
Reset init on a blank target |
Erase all the content of the flash |
Connect via the telnet interface and type
reset init |
Reset should return without error and the output should contain
executing reset script 'name_of_the_script' |
> reset init
JTAG tap: lpc2148.cpu tap/device found: 0x4f1f0f0f (mfg: 0x787, part: 0xf1f0, ver: 0x4)
srst pulls trst - can not reset into halted mode. Issuing halt after reset.
target state: halted
target halted in Thumb state due to debug-request, current mode: Supervisor
cpsr: 0xa00000f3 pc: 0x7fffd2da
core state: ARM
>
|
PASS
NOTE! Even if there is no message, the reset script is being executed (proved by side effects) |
| RES003 |
LPC2148 |
ZY1000 |
Reset after a power cycle of the target |
Reset the target then power cycle the target |
Connect via the telnet interface and type
reset halt after the power was detected |
Reset should return without error and the output should contain
target state: halted |
nsed nSRST asserted.
nsed power dropout.
nsed power restore.
SRST took 186ms to deassert
JTAG tap: lpc2148.cpu tap/device found: 0x4f1f0f0f (mfg: 0x787, part: 0xf1f0, ver: 0x4)
srst pulls trst - can not reset into halted mode. Issuing halt after reset.
target state: halted
target halted in Thumb state due to debug-request, current mode: Supervisor
cpsr: 0xa00000f3 pc: 0x7fffd2d6
core state: ARM
> reset halt
JTAG tap: lpc2148.cpu tap/device found: 0x4f1f0f0f (mfg: 0x787, part: 0xf1f0, ver: 0x4)
srst pulls trst - can not reset into halted mode. Issuing halt after reset.
target state: halted
target halted in Thumb state due to debug-request, current mode: Supervisor
cpsr: 0xa00000f3 pc: 0x7fffd2d6
>
|
PASS |
| RES004 |
LPC2148 |
ZY1000 |
Reset halt on a blank target where reset halt is supported |
Erase all the content of the flash |
Connect via the telnet interface and type
reset halt |
Reset should return without error and the output should contain
target state: halted
pc = 0 |
> reset halt
JTAG tap: lpc2148.cpu tap/device found: 0x4f1f0f0f (mfg: 0x787, part: 0xf1f0, ver: 0x4)
srst pulls trst - can not reset into halted mode. Issuing halt after reset.
target state: halted
target halted in Thumb state due to debug-request, current mode: Supervisor
cpsr: 0xa00000f3 pc: 0x7fffd2d6
>
|
PASS |
| RES005 |
LPC2148 |
ZY1000 |
Reset halt on a blank target using return clock |
Erase all the content of the flash, set the configuration script to use RCLK |
Connect via the telnet interface and type
reset halt |
Reset should return without error and the output should contain
target state: halted |
> jtag_khz 0
RCLK - adaptive
> reset init
JTAG tap: lpc2148.cpu tap/device found: 0x4f1f0f0f (mfg: 0x787, part: 0xf1f0, ver: 0x4)
srst pulls trst - can not reset into halted mode. Issuing halt after reset.
target state: halted
target halted in Thumb state due to debug-request, current mode: Supervisor
cpsr: 0xa00000f3 pc: 0x7fffd2d6
core state: ARM
>
|
PASS |
| ID |
Target |
ZY1000 |
Description |
Initial state |
Input |
Expected output |
Actual output |
Pass/Fail |
| SPD001 |
LPC2148 |
ZY1000 |
16MHz on normal operation |
Reset init the target according to RES002 |
Change speed and exercise a memory access over the JTAG, for example
mdw 0x0 32 |
The command should run without any errors. If any JTAG checking errors happen, the test failed |
> jtag_khz 16000
jtag_speed 4 => JTAG clk=16.000000
16000 kHz
> reset halt
JTAG scan chain interrogation failed: all zeroes
Check JTAG interface, timings, target power, etc.
error: -100
Command handler execution failed
in procedure 'reset' called at file "command.c", line 638
called at file "/home/laurentiu/workspace/zy1000/build/../openocd/src/helper/command.c", line 352
invalid mode value encountered 0
cpsr contains invalid mode value - communication failure
ThumbEE -- incomplete support
target state: halted
target halted in ThumbEE state due to debug-request, current mode: System
cpsr: 0x1fffffff pc: 0xfffffffa
invalid mode value encountered 0
cpsr contains invalid mode value - communication failure
target state: halted
target halted in Thumb state due to debug-request, current mode: System
cpsr: 0xc00003ff pc: 0xfffffff0
invalid mode value encountered 0
cpsr contains invalid mode value - communication failure
invalid mode value encountered 0
cpsr contains invalid mode value - communication failure
invalid mode value encountered 0
cpsr contains invalid mode value - communication failure
invalid mode value encountered 0
cpsr contains invalid mode value - communication failure
ThumbEE -- incomplete support
target state: halted
target halted in ThumbEE state due to debug-request, current mode: System
cpsr: 0xffffffff pc: 0xfffffffa
>
|
FAIL |
| SPD002 |
LPC2148 |
ZY1000 |
8MHz on normal operation |
Reset init the target according to RES002 |
Change speed and exercise a memory access over the JTAG, for example
mdw 0x0 32 |
The command should run without any errors. If any JTAG checking errors happen, the test failed |
> jtag_khz 8000
jtag_speed 8 => JTAG clk=8.000000
8000 kHz
> reset halt
JTAG scan chain interrogation failed: all zeroes
Check JTAG interface, timings, target power, etc.
error: -100
Command handler execution failed
in procedure 'reset' called at file "command.c", line 638
called at file "/home/laurentiu/workspace/zy1000/build/../openocd/src/helper/command.c", line 352
invalid mode value encountered 0
cpsr contains invalid mode value - communication failure
invalid mode value encountered 0
cpsr contains invalid mode value - communication failure
>
|
FAIL |
| SPD003 |
LPC2148 |
ZY1000 |
4MHz on normal operation |
Reset init the target according to RES002 |
Change speed and exercise a memory access over the JTAG, for example
mdw 0x0 32 |
The command should run without any errors. If any JTAG checking errors happen, the test failed |
> jtag_khz 4000
jtag_speed 16 => JTAG clk=4.000000
4000 kHz
> reset halt
JTAG tap: lpc2148.cpu tap/device found: 0xc79f0f87 (mfg: 0x7c3, part: 0x79f0, ver: 0xc)
JTAG tap: lpc2148.cpu UNEXPECTED: 0xc79f0f87 (mfg: 0x7c3, part: 0x79f0, ver: 0xc)
JTAG tap: lpc2148.cpu expected 1 of 1: 0x4f1f0f0f (mfg: 0x787, part: 0xf1f0, ver: 0x4)
Unexpected idcode after end of chain: 64 0x0000007f
Unexpected idcode after end of chain: 160 0x0000007f
Unexpected idcode after end of chain: 192 0x0000007f
Unexpected idcode after end of chain: 320 0x0000007f
Unexpected idcode after end of chain: 352 0x0000007f
Unexpected idcode after end of chain: 384 0x0000007f
Unexpected idcode after end of chain: 480 0x0000007f
Unexpected idcode after end of chain: 512 0x0000007f
Unexpected idcode after end of chain: 544 0x0000007f
double-check your JTAG setup (interface, speed, missing TAPs, ...)
error: -100
Command handler execution failed
in procedure 'reset' called at file "command.c", line 638
called at file "/home/laurentiu/workspace/zy1000/build/../openocd/src/helper/command.c", line 352
>
|
FAIL |
| SPD004 |
LPC2148 |
ZY1000 |
2MHz on normal operation |
Reset init the target according to RES002 |
Change speed and exercise a memory access over the JTAG, for example
mdw 0x0 32 |
The command should run without any errors. If any JTAG checking errors happen, the test failed |
> jtag_khz 2000
jtag_speed 32 => JTAG clk=2.000000
2000 kHz
> reset halt
JTAG tap: lpc2148.cpu tap/device found: 0x4f1f0f0f (mfg: 0x787, part: 0xf1f0, ver: 0x4)
srst pulls trst - can not reset into halted mode. Issuing halt after reset.
target state: halted
target halted in Thumb state due to debug-request, current mode: Supervisor
cpsr: 0xa00000f3 pc: 0x7fffd2da
> mdw 0 32
0x00000000: e59f4034 e3a05002 e5845000 e3a05003 e5845004 e59f201c e3a03000 e1020093
0x00000020: e2822028 e1021093 e3c03007 e5023028 e51ff004 7fffd1c4 e002c014 e01fc000
0x00000040: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff
0x00000060: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff
>
|
PASS |
| SPD005 |
LPC2148 |
ZY1000 |
RCLK on normal operation |
Reset init the target according to RES002 |
Change speed and exercise a memory access over the JTAG, for example
mdw 0x0 32 |
The command should run without any errors. If any JTAG checking errors happen, the test failed |
> jtag_khz 0
RCLK - adaptive
> mdw 0 32
0x00000000: e59f4034 e3a05002 e5845000 e3a05003 e5845004 e59f201c e3a03000 e1020093
0x00000020: e2822028 e1021093 e3c03007 e5023028 e51ff004 7fffd1c4 e002c014 e01fc000
0x00000040: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff
0x00000060: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff
>
|
PASS |
| ID |
Target |
Interface |
Description |
Initial state |
Input |
Expected output |
Actual output |
Pass/Fail |
| DBG001 |
LPC2148 |
ZY1000 |
Load is working |
Reset init is working, RAM is accesible, GDB server is started |
On the console of the OS:
arm-elf-gdb test_ram.elf
(gdb) target remote ip:port
(gdb) load
|
Load should return without error, typical output looks like:
Loading section .text, size 0x14c lma 0x0
Start address 0x40, load size 332
Transfer rate: 180 bytes/sec, 332 bytes/write.
|
(gdb) load
Loading section .text, size 0x16c lma 0x40000000
Start address 0x40000040, load size 364
Transfer rate: 32 KB/sec, 364 bytes/write.
(gdb)
|
PASS |
| DBG002 |
LPC2148 |
ZY1000 |
Software breakpoint |
Load the test_ram.elf application, use instructions from GDB001 |
In the GDB console:
(gdb) monitor gdb_breakpoint_override soft
software breakpoints enabled
(gdb) break main
Breakpoint 1 at 0xec: file src/main.c, line 71.
(gdb) continue
Continuing.
|
The software breakpoint should be reached, a typical output looks like:
target state: halted
target halted in ARM state due to breakpoint, current mode: Supervisor
cpsr: 0x000000d3 pc: 0x000000ec
Breakpoint 1, main () at src/main.c:71
71 DWORD a = 1;
|
(gdb) monitor gdb_breakpoint_override soft
force soft breakpoints
Current language: auto
The current source language is "auto; currently asm".
(gdb) break main
Breakpoint 1 at 0x4000010c: file src/main.c, line 71.
(gdb) c
Continuing.
Breakpoint 1, main () at src/main.c:71
71 DWORD a = 1;
Current language: auto
The current source language is "auto; currently c".
(gdb)
|
PASS |
| DBG003 |
LPC2148 |
ZY1000 |
Single step in a RAM application |
Load the test_ram.elf application, use instructions from GDB001, break in main using the instructions from GDB002 |
In GDB, type
(gdb) step |
The next instruction should be reached, typical output:
(gdb) step
target state: halted
target halted in ARM state due to single step, current mode: Abort
cpsr: 0x20000097 pc: 0x000000f0
target state: halted
target halted in ARM state due to single step, current mode: Abort
cpsr: 0x20000097 pc: 0x000000f4
72 DWORD b = 2;
|
(gdb) step
72 DWORD b = 2;
(gdb)
|
PASS |
| DBG004 |
LPC2148 |
ZY1000 |
Software break points are working after a reset |
Load the test_ram.elf application, use instructions from GDB001, break in main using the instructions from GDB002 |
In GDB, type
(gdb) monitor reset init
(gdb) load
(gdb) continue
|
The breakpoint should be reached, typical output:
target state: halted
target halted in ARM state due to breakpoint, current mode: Supervisor
cpsr: 0x000000d3 pc: 0x000000ec
Breakpoint 1, main () at src/main.c:71
71 DWORD a = 1;
|
(gdb) moni reset init
JTAG tap: lpc2148.cpu tap/device found: 0x4f1f0f0f (mfg: 0x787, part: 0xf1f0, ver: 0x4)
srst pulls trst - can not reset into halted mode. Issuing halt after reset.
target state: halted
target halted in Thumb state due to debug-request, current mode: Supervisor
cpsr: 0xa00000f3 pc: 0x7fffd2d6
core state: ARM
(gdb) load
Loading section .text, size 0x16c lma 0x40000000
Start address 0x40000040, load size 364
Transfer rate: 27 KB/sec, 364 bytes/write.
(gdb) c
Continuing.
Breakpoint 1, main () at src/main.c:71
71 DWORD a = 1;
(gdb)
|
PASS |
| DBG005 |
LPC2148 |
ZY1000 |
Hardware breakpoint |
Flash the test_rom.elf application. Make this test after FLA004 has passed |
Be sure that gdb_memory_map and gdb_flash_program are enabled. In GDB, type
(gdb) monitor reset init
(gdb) load
Loading section .text, size 0x194 lma 0x100000
Start address 0x100040, load size 404
Transfer rate: 179 bytes/sec, 404 bytes/write.
(gdb) monitor gdb_breakpoint_override hard
force hard breakpoints
(gdb) break main
Breakpoint 1 at 0x100134: file src/main.c, line 69.
(gdb) continue
|
The breakpoint should be reached, typical output:
Continuing.
Breakpoint 1, main () at src/main.c:69
69 DWORD a = 1;
|
(gdb) monitor gdb_breakpoint_override hard
force hard breakpoints
(gdb) break main
Breakpoint 1 at 0x10c: file src/main.c, line 71.
(gdb) continue
Continuing.
Note: automatically using hardware breakpoints for read-only addresses.
Breakpoint 1, main () at src/main.c:71
71 DWORD a = 1;
Current language: auto
The current source language is "auto; currently c".
(gdb)
|
PASS NOTE: This test is failing from time to time, not able to describe a cause |
| DBG006 |
LPC2148 |
ZY1000 |
Hardware breakpoint is set after a reset |
Follow the instructions to flash and insert a hardware breakpoint from DBG005 |
In GDB, type
(gdb) monitor reset
(gdb) monitor reg pc 0x100000
pc (/32): 0x00100000
(gdb) continue
where the value inserted in PC is the start address of the application
|
The breakpoint should be reached, typical output:
Continuing.
Breakpoint 1, main () at src/main.c:69
69 DWORD a = 1;
|
(gdb) monitor reset init
JTAG tap: lpc2148.cpu tap/device found: 0x4f1f0f0f (mfg: 0x787, part: 0xf1f0, ver: 0x4)
srst pulls trst - can not reset into halted mode. Issuing halt after reset.
target state: halted
target halted in ARM state due to debug-request, current mode: Supervisor
cpsr: 0x60000013 pc: 0x00000160
core state: ARM
(gdb) monitor reg pc 0x40
pc (/32): 0x00000040
(gdb) continue
Continuing.
Breakpoint 1, main () at src/main.c:71
71 DWORD a = 1;
(gdb)
|
PASS |
| DBG007 |
LPC2148 |
ZY1000 |
Single step in ROM |
Flash the test_rom.elf application and set a breakpoint in main, use DBG005. Make this test after FLA004 has passed |
Be sure that gdb_memory_map and gdb_flash_program are enabled. In GDB, type
(gdb) monitor reset
(gdb) load
Loading section .text, size 0x194 lma 0x100000
Start address 0x100040, load size 404
Transfer rate: 179 bytes/sec, 404 bytes/write.
(gdb) monitor gdb_breakpoint_override hard
force hard breakpoints
(gdb) break main
Breakpoint 1 at 0x100134: file src/main.c, line 69.
(gdb) continue
Continuing.
Breakpoint 1, main () at src/main.c:69
69 DWORD a = 1;
(gdb) step
|
The breakpoint should be reached, typical output:
target state: halted
target halted in ARM state due to single step, current mode: Supervisor
cpsr: 0x60000013 pc: 0x0010013c
70 DWORD b = 2;
|
(gdb) load
Loading section .text, size 0x16c lma 0x0
Start address 0x40, load size 364
Transfer rate: 637 bytes/sec, 364 bytes/write.
(gdb) monitor gdb_breakpoint_override hard
force hard breakpoints
Current language: auto
The current source language is "auto; currently asm".
(gdb) break main
Breakpoint 1 at 0x10c: file src/main.c, line 71.
(gdb) continue
Continuing.
Note: automatically using hardware breakpoints for read-only addresses.
Breakpoint 1, main () at src/main.c:71
71 DWORD a = 1;
Current language: auto
The current source language is "auto; currently c".
(gdb) step
72 DWORD b = 2;
(gdb)
|
PASS |
| ID |
Target |
Interface |
Description |
Initial state |
Input |
Expected output |
Actual output |
Pass/Fail |
| RAM001 |
LPC2148 |
ZY1000 |
32 bit Write/read RAM |
Reset init is working |
On the telnet interface
> mww ram_address 0xdeadbeef 16
> mdw ram_address 32
|
The commands should execute without error. A clear failure is a memory access exception. The result of running the commands should be a list of 16 locations 32bit long containing 0xdeadbeef.
> mww 0x0 0xdeadbeef 16
> mdw 0x0 32
0x00000000: deadbeef deadbeef deadbeef deadbeef deadbeef deadbeef deadbeef deadbeef
0x00000020: deadbeef deadbeef deadbeef deadbeef deadbeef deadbeef deadbeef deadbeef
0x00000040: e1a00000 e59fa51c e59f051c e04aa000 00080017 00009388 00009388 00009388
0x00000060: 00009388 0002c2c0 0002c2c0 000094f8 000094f4 00009388 00009388 00009388
|
> mww 0x40000000 0xdeadbeef 16
> mdw 0x40000000 32
0x40000000: deadbeef deadbeef deadbeef deadbeef deadbeef deadbeef deadbeef deadbeef
0x40000020: deadbeef deadbeef deadbeef deadbeef deadbeef deadbeef deadbeef deadbeef
0x40000040: e1a00000 e1a00000 e1a00000 e1a00000 e1a00000 e1a00000 e1a00000 e1a00000
0x40000060: e321f0db e59fd07c e321f0d7 e59fd078 e321f0d1 e59fd074 e321f0d2 e59fd070
>
|
PASS |
| RAM002 |
LPC2148 |
ZY1000 |
16 bit Write/read RAM |
Reset init is working |
On the telnet interface
> mwh ram_address 0xbeef 16
> mdh ram_address 32
|
The commands should execute without error. A clear failure is a memory access exception. The result of running the commands should be a list of 16 locations 16bit long containing 0xbeef.
> mwh 0x0 0xbeef 16
> mdh 0x0 32
0x00000000: beef beef beef beef beef beef beef beef beef beef beef beef beef beef beef beef
0x00000020: 00e0 0000 021c 0000 0240 0000 026c 0000 0288 0000 0000 0000 0388 0000 0350 0000
>
|
> mwh 0x40000000 0xbeef 16
> mdh 0x40000000 32
0x40000000: beef beef beef beef beef beef beef beef beef beef beef beef beef beef beef beef
0x40000020: beef dead beef dead beef dead beef dead beef dead beef dead beef dead beef dead
>
|
PASS |
| RAM003 |
LPC2148 |
ZY1000 |
8 bit Write/read RAM |
Reset init is working |
On the telnet interface
> mwb ram_address 0xab 16
> mdb ram_address 32
|
The commands should execute without error. A clear failure is a memory access exception. The result of running the commands should be a list of 16 locations 8bit long containing 0xab.
> mwb ram_address 0xab 16
> mdb ram_address 32
0x00000000: ab ab ab ab ab ab ab ab ab ab ab ab ab ab ab ab 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
>
|
> mwb 0x40000000 0xab 16
> mdb 0x40000000 32
0x40000000: ab ab ab ab ab ab ab ab ab ab ab ab ab ab ab ab ef be ef be ef be ef be ef be ef be ef be ef be
>
|
PASS |
| ID |
Target |
Interface |
Description |
Initial state |
Input |
Expected output |
Actual output |
Pass/Fail |
| FLA001 |
LPC2148 |
ZY1000 |
Flash probe |
Reset init is working |
On the telnet interface:
> flash probe 0
|
The command should execute without error. The output should state the name of the flash and the starting address. An example of output:
flash 'ecosflash' found at 0x01000000
|
> flash probe 0
flash 'lpc2000' found at 0x00000000
|
PASS |
| FLA002 |
LPC2148 |
ZY1000 |
flash fillw |
Reset init is working, flash is probed |
On the telnet interface
> flash fillw 0x1000000 0xdeadbeef 16
|
The commands should execute without error. The output looks like:
wrote 64 bytes to 0x01000000 in 11.610000s (0.091516 kb/s)
To verify the contents of the flash:
> mdw 0x1000000 32
0x01000000: deadbeef deadbeef deadbeef deadbeef deadbeef deadbeef deadbeef deadbeef
0x01000020: deadbeef deadbeef deadbeef deadbeef deadbeef deadbeef deadbeef deadbeef
0x01000040: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff
0x01000060: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff
|
> flash fillw 0x0 0xdeadbeef 16
Verification will fail since checksum in image (0xdeadbeef) to be written to flash is different from calculated vector checksum (0xe93fc777).
To remove this warning modify build tools on developer PC to inject correct LPC vector checksum.
wrote 64 bytes to 0x00000000 in 0.040000s (1.563 kb/s)
> mdw 0 32
0x00000000: deadbeef deadbeef deadbeef deadbeef deadbeef e93fc777 deadbeef deadbeef
0x00000020: deadbeef deadbeef deadbeef deadbeef deadbeef deadbeef deadbeef deadbeef
0x00000040: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff
0x00000060: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff
>
|
FAIL |
| FLA003 |
LPC2148 |
ZY1000 |
Flash erase |
Reset init is working, flash is probed |
On the telnet interface
> flash erase_address 0x1000000 0x2000
|
The commands should execute without error.
erased address 0x01000000 length 8192 in 4.970000s
To check that the flash has been erased, read at different addresses. The result should always be 0xff.
> mdw 0x1000000 32
0x01000000: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff
0x01000020: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff
0x01000040: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff
0x01000060: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff
|
> flash erase_address 0 0x2000
erased address 0x00000000 (length 8192) in 0.510000s (15.686 kb/s)
> mdw 0 32
0x00000000: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff
0x00000020: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff
0x00000040: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff
0x00000060: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff
>
|
PASS |
| FLA004 |
LPC2148 |
ZY1000 |
Loading to flash from GDB |
Reset init is working, flash is probed, connectivity to GDB server is working |
Start GDB using a ROM elf image, eg: arm-elf-gdb test_rom.elf.
(gdb) target remote ip:port
(gdb) monitor reset
(gdb) load
Loading section .text, size 0x194 lma 0x100000
Start address 0x100040, load size 404
Transfer rate: 179 bytes/sec, 404 bytes/write.
(gdb) monitor verify_image path_to_elf_file
|
The output should look like:
verified 404 bytes in 5.060000s
The failure message is something like:
Verify operation failed address 0x00200000. Was 0x00 instead of 0x18
|
(gdb) moni verify_image /tftp/10.0.0.194/test_rom.elf
checksum mismatch - attempting binary compare
Verify operation failed address 0x00000014. Was 0x58 instead of 0x60
Command handler execution failed
in procedure 'verify_image' called at file "command.c", line 647
called at file "command.c", line 361
(gdb)
|
FAIL |