diff options
Diffstat (limited to 'doc/openocd.texi')
| -rw-r--r-- | doc/openocd.texi | 159 |
1 files changed, 85 insertions, 74 deletions
diff --git a/doc/openocd.texi b/doc/openocd.texi index 5663a629..987a1d25 100644 --- a/doc/openocd.texi +++ b/doc/openocd.texi @@ -2953,112 +2953,123 @@ When performing a unlock remember that you will not be able to halt the str9 - i has been locked. Halting the core is not required for the @option{str9xpec} driver as mentioned above, just issue the commands above manually or from a telnet prompt. -@subsubsection str9xpec driver options - -@b{flash bank str9xpec} <@var{base}> <@var{size}> 0 0 <@var{target}> -@*Before using the flash commands the turbo mode must be enabled using str9xpec -@option{enable_turbo} <@var{num>.} - +@deffn {Flash Driver} str9xpec Only use this driver for locking/unlocking the device or configuring the option bytes. Use the standard str9 driver for programming. +Before using the flash commands the turbo mode must be enabled using the +@command{str9xpec enable_turbo} command. -@subsubsection str9xpec specific commands -@cindex str9xpec specific commands -These are flash specific commands when using the str9xpec driver. +Several str9xpec-specific commands are defined: -@itemize @bullet -@item @b{str9xpec enable_turbo} <@var{num}> -@cindex str9xpec enable_turbo -@*enable turbo mode, will simply remove the str9 from the chain and talk +@deffn Command {str9xpec disable_turbo} num +Restore the str9 into JTAG chain. +@end deffn + +@deffn Command {str9xpec enable_turbo} num +Enable turbo mode, will simply remove the str9 from the chain and talk directly to the embedded flash controller. -@item @b{str9xpec disable_turbo} <@var{num}> -@cindex str9xpec disable_turbo -@*restore the str9 into JTAG chain. -@item @b{str9xpec lock} <@var{num}> -@cindex str9xpec lock -@*lock str9 device. The str9 will only respond to an unlock command that will +@end deffn + +@deffn Command {str9xpec lock} num +Lock str9 device. The str9 will only respond to an unlock command that will erase the device. -@item @b{str9xpec unlock} <@var{num}> -@cindex str9xpec unlock -@*unlock str9 device. -@item @b{str9xpec options_read} <@var{num}> -@cindex str9xpec options_read -@*read str9 option bytes. -@item @b{str9xpec options_write} <@var{num}> -@cindex str9xpec options_write -@*write str9 option bytes. -@end itemize +@end deffn -@subsubsection STR9 option byte configuration -@cindex STR9 option byte configuration +@deffn Command {str9xpec part_id} num +Prints the part identifier for bank @var{num}. +@end deffn + +@deffn Command {str9xpec options_cmap} num (@option{bank0}|@option{bank1}) +Configure str9 boot bank. +@end deffn + +@deffn Command {str9xpec options_lvdsel} num (@option{vdd}|@option{vdd_vddq}) +Configure str9 lvd source. +@end deffn + +@deffn Command {str9xpec options_lvdthd} num (@option{2.4v}|@option{2.7v}) +Configure str9 lvd threshold. +@end deffn + +@deffn Command {str9xpec options_lvdwarn} bank (@option{vdd}|@option{vdd_vddq}) +Configure str9 lvd reset warning source. +@end deffn + +@deffn Command {str9xpec options_read} num +Read str9 option bytes. +@end deffn + +@deffn Command {str9xpec options_write} num +Write str9 option bytes. +@end deffn + +@deffn Command {str9xpec unlock} num +unlock str9 device. +@end deffn + +@end deffn -@itemize @bullet -@item @b{str9xpec options_cmap} <@var{num}> <@option{bank0}|@option{bank1}> -@cindex str9xpec options_cmap -@*configure str9 boot bank. -@item @b{str9xpec options_lvdthd} <@var{num}> <@option{2.4v}|@option{2.7v}> -@cindex str9xpec options_lvdthd -@*configure str9 lvd threshold. -@item @b{str9xpec options_lvdsel} <@var{num}> <@option{vdd}|@option{vdd_vddq}> -@cindex str9xpec options_lvdsel -@*configure str9 lvd source. -@item @b{str9xpec options_lvdwarn} <@var{bank}> <@option{vdd}|@option{vdd_vddq}> -@cindex str9xpec options_lvdwarn -@*configure str9 lvd reset warning source. -@end itemize @section mFlash @subsection mFlash Configuration @cindex mFlash Configuration -@b{mflash bank} <@var{soc}> <@var{base}> <@var{RST pin}> <@var{target}> -@cindex mflash bank -@*Configures a mflash for <@var{soc}> host bank at -<@var{base}>. Pin number format is dependent on host GPIO calling convention. -Currently, mflash bank support s3c2440 and pxa270. -(ex. of s3c2440) mflash <@var{RST pin}> is GPIO B1. +@deffn {Config Command} {mflash bank} soc base RST_pin target +Configures a mflash for @var{soc} host bank at +address @var{base}. +The pin number format depends on the host GPIO naming convention. +Currently, the mflash driver supports s3c2440 and pxa270. + +Example for s3c2440 mflash where @var{RST pin} is GPIO B1: @example mflash bank s3c2440 0x10000000 1b 0 @end example -(ex. of pxa270) mflash <@var{RST pin}> is GPIO 43. +Example for pxa270 mflash where @var{RST pin} is GPIO 43: @example mflash bank pxa270 0x08000000 43 0 @end example +@end deffn @subsection mFlash commands @cindex mFlash commands -@itemize @bullet -@item @b{mflash probe} -@cindex mflash probe -@*Probe mflash. -@item @b{mflash write} <@var{num}> <@var{file}> <@var{offset}> -@cindex mflash write -@*Write the binary <@var{file}> to mflash bank <@var{num}>, starting at -<@var{offset}> bytes from the beginning of the bank. -@item @b{mflash dump} <@var{num}> <@var{file}> <@var{offset}> <@var{size}> -@cindex mflash dump -@*Dump <size> bytes, starting at <@var{offset}> bytes from the beginning of the <@var{num}> bank -to a <@var{file}>. -@item @b{mflash config pll} <@var{frequency}> -@cindex mflash config pll -@*Configure mflash pll. <@var{frequency}> is input frequency of mflash. The order is Hz. +@deffn Command {mflash config pll} frequency +Configure mflash PLL. +The @var{frequency} is the mflash input frequency, in Hz. Issuing this command will erase mflash's whole internal nand and write new pll. After this command, mflash needs power-on-reset for normal operation. If pll was newly configured, storage and boot(optional) info also need to be update. -@item @b{mflash config boot} -@cindex mflash config boot -@*Configure bootable option. If bootable option is set, mflash offer the first 8 sectors +@end deffn + +@deffn Command {mflash config boot} +Configure bootable option. +If bootable option is set, mflash offer the first 8 sectors (4kB) for boot. -@item @b{mflash config storage} -@cindex mflash config storage -@*Configure storage information. For the normal storage operation, this information must be +@end deffn + +@deffn Command {mflash config storage} +Configure storage information. +For the normal storage operation, this information must be written. -@end itemize +@end deffn + +@deffn Command {mflash dump} num filename offset size +Dump @var{size} bytes, starting at @var{offset} bytes from the +beginning of the bank @var{num}, to the file named @var{filename}. +@end deffn + +@deffn Command {mflash probe} +Probe mflash. +@end deffn + +@deffn Command {mflash write} num filename offset +Write the binary file @var{filename} to mflash bank @var{num}, starting at +@var{offset} bytes from the beginning of the bank. +@end deffn @node NAND Flash Commands @chapter NAND Flash Commands |