diff options
Diffstat (limited to 'doc')
| -rw-r--r-- | doc/openocd.texi | 36 |
1 files changed, 18 insertions, 18 deletions
diff --git a/doc/openocd.texi b/doc/openocd.texi index adc8a30c..9e92b606 100644 --- a/doc/openocd.texi +++ b/doc/openocd.texi @@ -544,7 +544,7 @@ Some key things you should look at and understand are: @enumerate @item The RESET configuration of your debug environment as a hole -@item Is there a ``work area'' that that OpenOCD can use? +@item Is there a ``work area'' that OpenOCD can use? @* For ARM - work areas mean up to 10x faster downloads. @item For MMU/MPU based ARM chips (ie: ARM9 and later) will that work area still be available? @item For complex targets (multiple chips) the JTAG SPEED becomes an issue. @@ -920,7 +920,7 @@ can type a Tcl for() loop, set variables, etc. @node Daemon Configuration @chapter Daemon Configuration -The commands here are commonly found inthe openocd.cfg file and are +The commands here are commonly found in the openocd.cfg file and are used to specify what TCP/IP ports are used, and how GDB should be supported. @section init @@ -1492,9 +1492,9 @@ have the taps created in the proper order. by the ``jtag newtap'' command. The documentation remains here so that one can easily convert the old syntax to the new syntax. About the old syntax: The old syntax is positional, ie: The 4th parameter is the -``irmask'' The new syntax requires named prefixes, and supports -additional options, for example ``-irmask 4'' Please refer to the -@b{jtag newtap} command for deails. +``irmask''. The new syntax requires named prefixes, and supports +additional options, for example ``-irmask 4''. Please refer to the +@b{jtag newtap} command for details. @example OLD: jtag_device 8 0x01 0x0e3 0xfe NEW: jtag newtap CHIPNAME TAPNAME -irlen 8 -ircapture 0xe3 -irmask 0xfe @@ -1543,7 +1543,7 @@ The IEEE JTAG definition has no concept of a ``disabled'' tap. @b{jtag tapisenabled DOTTED.NAME} -This command return 1 if the named tap is currently enabled, 0 if not. +This command returns 1 if the named tap is currently enabled, 0 if not. This command exists so that scripts that manipulate a JRC (like the Omap3530 has) can determine if OpenOCD thinks a tap is presently enabled, or disabled. @@ -1558,7 +1558,7 @@ creating a ``target'' a JTAG Tap DOTTED.NAME must exist first. @section targets [NAME] @b{Note:} This command name is PLURAL - not singular. -With NO parameter, this pural @b{targets} command lists all known +With NO parameter, this plural @b{targets} command lists all known targets in a human friendly form. With a parameter, this pural @b{targets} command sets the current @@ -1690,13 +1690,13 @@ with odd reset situations and are not documented here. @end itemize @section Target Events -At various times, certian things happen, or you want to happen. +At various times, certain things can happen, or you want them to happen. Examples: @itemize @bullet @item What should happen when GDB connects? Should your target reset? @item When GDB tries to flash the target, do you need to enable the flash via a special command? -@item During reset, do you need to write to certian memory locations to reconfigure the SDRAM? +@item During reset, do you need to write to certain memory location to reconfigure the SDRAM? @end itemize All of the above items are handled by target events. @@ -1708,7 +1708,7 @@ Syntactially, the option is: ``-event NAME BODY'' where NAME is a target event name, and BODY is a tcl procedure or string of commands to execute. -The programers model is the: ``-command'' option used in Tcl/Tk +The programmers model is the ``-command'' option used in Tcl/Tk buttons and events. Below are two identical examples, the first creates and invokes small procedure. The second inlines the procedure. @@ -1822,13 +1822,13 @@ command. @comment end TYPES @end itemize @item @b{PARAMS} -@*PARAMs are various target configure parameters, the following are manditory -at configuration. -@comment START manditory +@*PARAMs are various target configure parameters, the following are mandatory +at configuration: +@comment START mandatory @itemize @bullet @item @b{-endian big|little} @item @b{-chain-position DOTTED.NAME} -@comment end MANDITORY +@comment end MANDATORY @end itemize @comment END params @end itemize @@ -3269,7 +3269,7 @@ OpenOCD. @section TCL Rule #1 There is a famous joke, it goes like this: @enumerate -@item Rule #1: The wife is aways correct +@item Rule #1: The wife is always correct @item Rule #2: If you think otherwise, See Rule #1 @end enumerate @@ -3280,7 +3280,7 @@ The TCL equal is this: @item Rule #2: If you think otherwise, See Rule #1 @end enumerate -As in the famous joke, the consiquences of Rule #1 are profound. Once +As in the famous joke, the consequences of Rule #1 are profound. Once you understand Rule #1, you will understand TCL. @section TCL Rule #1b @@ -3350,9 +3350,9 @@ nested 3 times@}@}@} NOTE: [date] is perhaps a bad example, as of 28/nov/2008, Jim/OpenOCD does not have a date command. @end itemize -@section Consiquences of Rule 1/2/3/4 +@section Consequences of Rule 1/2/3/4 -The consiquences of Rule 1 is profound. +The consequences of Rule 1 is profound. @subsection Tokenizing & Execution. |