summaryrefslogtreecommitdiff
Commit message (Collapse)AuthorAgeFilesLines
...
* ADIv5: remove ATOMIC/COMPOSITE interface modeDavid Brownell2010-02-213-98/+29
| | | | | | | | | | | | | This removes context-sensitivity from the programming interface and makes it possible to know what a block of code does without needing to know the previous history (specifically, the DAP's "trans_mode" setting). The mode was only set to ATOMIC briefly after DAP initialization, making this patch be primarily cleanup; almost everything depends on COMPOSITE. The transactions which shouldn't have been queued were already properly flushing the queue. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
* ARM: ADIv5, deadcode cleanupDavid Brownell2010-02-211-13/+13
| | | | | | | | | | | | I have no idea what the scan_inout_check() was *expecting* to achieve by issuing a read of the DP_RDBUFF register. But in any case, that code was clearly never being called ("invalue" always NULL) ... so remove it, and the associated comment. Also rename it as ap_write_check(), facilitating a cleanup of its single call site by removing constant parameters. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
* ARM: ADIv5 code shrinkage, cleanupDavid Brownell2010-02-211-40/+16
| | | | | | | | | | adi_jtag_dp_scan_u32() now wraps adi_jtag_dp_scan(), removing code duplication. Include doxygen for the former. Comment some particularly relevant points. Minor fault handling fixes for both routines: don't register a callback that can't run, or return ERROR_OK after an error. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
* ADIv5 clean up AP fault handlingDavid Brownell2010-02-211-32/+46
| | | | | | | | | | | | | | | | | Pass up fault codes from various routines, so their callers can clean up after failures, and remove the FIXME comments highlighting those previously goofy code paths. dap_ap_{read,write}_reg_u32() dap_ap_write_reg() mem_ap_{read,write}_u32() mem_ap_{read,write}_atomic_u32() dap_setup_accessport() Make dap_ap_write_reg_u32() just wrap dap_ap_write_reg(), instead of cloning its core code (and broken fault handling). Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
* ADIv5 clean up AP selection and register cachingDavid Brownell2010-02-214-34/+60
| | | | | | | | | | | | | | | | | | | Handling of AP (and AP register bank) selection, and cached AP registers, is pretty loose ... start tightening it: - It's "AP bank" select support ... there are no DP banks. Rename. + dap_dp_bankselect() becomes dap_ap_bankselect() + "dp_select_value" struct field becomes "ap_bank_value" - Remove duplicate AP cache init paths ... only use dap_ap_select(), and don't make Cortex (A8 or M3) cores roll their own code. - For dap_ap_bankselect(), pass up any fault code from writing the SELECT register. (Nothing yet checks those codes.) - Add various bits of Doxygen Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
* ARM: keep a handle to the PCDavid Brownell2010-02-2116-88/+106
| | | | | | | | | | | | | | | | Keep a handle to the PC in "struct arm", and use it. This register is used a fair amount, so this is a net minor code shrink (other than some line length fixes), but mostly it's to make things more readable. For XScale, fix a dodgy sequence while stepping. It was initializing a variable to a non-NULL value, then updating it to handle the step-over-active-breakpoint case, and then later testing for non-NULL to see if it should reverse that step-over-active logic. It should have done like ARM7/ARM9 does: init to NULL. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
* ARM DPM: support adding/removing HW breakpointsDavid Brownell2010-02-211-38/+113
| | | | | | | | | | | | | | Generalize the core of watchpoint setup so that it can handle breakpoints too. Create breakpoint add/remove routines which will use that, and hook them up to target types which don't provide their own breakpoint support (nothing, yet). This suffices for hardware-only breakpoint support. The ARM11 code will be able to switch over to this without much trouble, since it doesn't yet handle software breakpoints. Switching Cortex-A8 will be a bit more involved. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
* ARM11: per-core options should not be globalDavid Brownell2010-02-212-33/+44
| | | | | | | | | | Address some FIXME comments by getting rid of globals, moving per-core parameters in the existing per-core data structure. This will matter most whenever there are multiple ARM11 cores, e.g. ARM11 MPcore chips, but in general is just cleanup. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
* ARMv7-M: start using "struct arm"David Brownell2010-02-215-9/+74
| | | | | | | | | | | | | | | | | | | | | | | | | | | This sets up a few of the core "struct arm" data structures so they can be used with ARMv7-M cores. Specifically, it: - defines new ARM core_modes to match the microcontroller modes (e.g. HANDLER not IRQ, and two types of thread mode); - Establishes a new microcontroller "core_type", which can be used to make sure v7-M (and v6-M) cores are handled right; - adds "struct arm" to "struct armv7m" and arranges for the target_to_armv7m() converter to use it; - sets up the arm.core_cache and arm.cpsr values - makes the Cortex-M3 code maintain arm.map and arm.core_mode. This is currently set up as a parallel data structure, primarily to minimize special cases for the semihosting support with microcontroller profile cores. Later patches can rip out the duplicative ARMv7-M support and start reusing core ARM code. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
* Open the merge window for the 0.5.0 release cycle.David Brownell2010-02-213-69/+101
| | | | Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
* Label builds as OpenOCD v0.4.0David Brownell2010-02-211-1/+1
| | | | Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
* User's Guide mentions OS-specific installationDavid Brownell2010-02-212-2/+14
| | | | | | | | | | Specifically the Linux issue of needing "udev" rules, and MS-Windows needing driver configuration. Also, update the existing udev note to use the correct name of that rules file in the source tree. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
* arm920t line length cleanupDavid Brownell2010-02-201-115/+247
| | | | | | | | | | | | The recent patch to fixbreakpoints and dcache handling added a bunch of overlong lines (80+ chars) ... shrink them, and do the same to a few lines which were already overlong. Also add a few FIXME comments to nudge (a) replacement of some magic numbers with opcode macros, which will be much better at showing what's actually going on, and (b) correct return codes. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
* CSB337 board cleanup (quasi-regression)David Brownell2010-02-201-0/+2
| | | | | | | | Get rid of new nasty warning: NOTE! Severe performance degradation without fast memory access enabled... Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
* FreeBSD buildfixDavid Brownell2010-02-201-2/+2
| | | | | | | | | Fix an unused variable warning seen when building the parport driver under FreeBSD. Using information from Xiaofan Chen <xiaofanc@gmail.com> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
* atm920t : fix breakpoints and data cache handlingMarc Pignat2010-02-191-17/+103
| | | | | | | | | Breakpoints did not work because the data cache was not flushed properly. As a bonus add capability to write to memory marked as read only by the MMU, which allows software breakpoints in such memory regions.
* ARM920T scanchain 15 comments/cleanupDavid Brownell2010-02-161-51/+112
| | | | | | | | | | | | | | | | | For folk who don't know the ARM920 JTAG interface very well, the two modes of scan chain 15 access to CP15 are confusing. Make those parts of the ARM920 code less opaque, by: - Adding comments referencing the relevant parts of the TRM, catching up to similar updates in the User's Guide. - Replacing magic numbers in physical access clients with symbolic equivalents. No functional change. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
* gpl: fix GPL startup messageØyvind Harboe2010-02-152-2/+3
| | | | Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
* LPC1768.cfg -- partial fixes for bogus reset-init handlerDavid Brownell2010-02-151-4/+4
| | | | | | | | | Cortex-M targets don't support ARM instructions. Leave the NVIC.VTOR setup alone, but comment how the whole routine looks like one big bug... Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
* fix crash with DSP563XXMathias Kuester2010-02-141-0/+25
| | | | | | | | | | | When a DSP563xx-aware GDB asks OpenOCD for target registers, the result should be a GDB with register data ... not an OpenOCD crash. (Note that mainline GDB doesn't currently support this core, so for now, this requires a GDB with FreeScale patches.) Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
* NEWS: mention removal of obsolete commandsDavid Brownell2010-02-131-0/+2
| | | | | | | | | | | | | Removed remaining support for various commands, like advice for migrating old-style TAP declarations. The documentation no longer describes them either ... so if users have been delaying config updates, they may need to consult older releases. ALL this stuff has been clearly marked as "do not use" for at least a year now, so anyone still using it hasn't been holding up their end. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
* Restore "-dev" version suffix (0.4.0-rc2-dev)David Brownell2010-02-131-1/+1
| | | | Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
* v4.0-rc2 milestoneDavid Brownell2010-02-131-1/+1
| | | | Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
* STR9xpec: issue warning when unlocking deviceSpencer Oliver2010-02-121-0/+8
| | | | | | | Issue warning to user when unlocking or writing the option bytes. The new settings will not take effect until a target reset. Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
* STM32x: issue warning when unlocking device (bug #16)Spencer Oliver2010-02-121-2/+6
| | | | | | | Issue warning to user when unlocking or writing the option bytes. The new settings will not take effect until a target reset. Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
* arm720t: virt2phys callback addedØyvind Harboe2010-02-121-4/+14
| | | | | | | | This is a copy and paste of arm926ejs. Not tested, but ready for testing at least. There is a good chance that it will work if the generic armv4_5 fn's are robust enough... Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
* arm920: add virt2phys fnMarc Pignat2010-02-121-3/+13
| | | | | | | Copy of the 926ejs function. I have tested it only using my rtems application (where virtual address mapping == physical). Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
* target library: configuration files for openocd tested with Atmel SAM-ICE V6 ↵Viktar Palstsiuk2010-02-112-0/+119
| | | | | | JTAG. Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
* User's Guide: "#" in filesystems names is badDavid Brownell2010-02-101-6/+14
| | | | | | | | Sometimes MS-Windows users try to use filesystem names which include the "#" character. That's generally unwise, since it begins Tcl comments. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
* arm11: fix another infinite loop bugØyvind Harboe2010-02-101-4/+23
| | | | | | | | | | | | | reset init would get stuck in an infinite loop when e.g. khz was too high. Added timeout. This is a copy of paste of a number of such bugfixes in the arm11 code. Arm11 code reviewed for further such infinite loop bugs and I couldn't find any more. Xing fingers it's the last one... Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
* User's Guide: clarify jtag_rclk adviceDavid Brownell2010-02-101-2/+4
| | | | | | | | | | Not all cores and boards support adaptive clocking, so qualify all advice to use it to depend on core and board support. It's primarily ARM cores which support this; and many of the newer ones (like Cortex-M series) don't. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
* target: add todo in target_write_memory() about alignmentØyvind Harboe2010-02-091-2/+13
| | | | | | | target_write_buffer() does not align "buffer" in host memory passed to target_write_memory(). Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
* str730.cfg: fix incorrect mem regionsSpencer Oliver2010-02-091-2/+2
| | | | | | - update str73x mem regions to correct values. Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
* Re-title Developer's GuideDavid Brownell2010-02-061-2/+2
| | | | | | | | | | | | The Doxygen output was previously titled "OpenOCD Reference Manual", which was quite misleading ... the User's Guide is the reference manual which folk should consult about how to use the software. Just rename it to match how it's been discussed previously, and to bring out its intended audience: developers of this software. As a rule, Doxygen is only for folk who work with the code it documents. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
* ADIv5: doxygenDavid Brownell2010-02-062-32/+138
| | | | | | | | | | | | | | | | | Provide doxygen for many of the public ADIv5 interfaces (i.e. the ones called from Cortex core support code). Add FIXMEs (and a TODO) to help resolve implementation issues which became more apparent when trying to document this code: - Error-prone context-sensitivity (queued/nonqueued) in many procedures. - Procedures that lie by ignoring errors and wrongly claiming success. Also, there was no point in a return from dap_ap_select(); it can't fail, and no caller checks its return status. Clean that up, make it void. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
* zy1000: complete zy1000_uart to jim command switchØyvind Harboe2010-02-051-6/+6
| | | | Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
* ARMv7-M: make DAP commands verify target is an ARMv7-MDavid Brownell2010-02-042-3/+31
| | | | | | | | Init the ARMv7-M magic number. Define predicate verifying it. Use it to resolve a lurking bug/FIXME: make sure the ARMv7-M specific DAP ops reject non-ARMv7-M targets. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
* Documentation: mention bug databaseDavid Brownell2010-02-042-1/+14
| | | | | | | Have the User's Guide and BUG handling notes both reference the fact that we now have a bug database at SourceForge. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
* JLink: reference protocol documentationDavid Brownell2010-02-041-0/+4
| | | | | | | Segger publishes some documentation on this protocol; reference it, so future maintainers can know it exists. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
* CMD: duplicate cmd error msgSpencer Oliver2010-02-041-1/+4
| | | | | | | | | When registering cmds we report duplicate attempts to register a cmd as a LOG_ERROR. Some situations need this, such as when registering dual flash banks. http://www.mail-archive.com/openocd-development@lists.berlios.de/msg11152.html Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
* scripts: Phytec/LPC2350 config scriptsEthan Eade2010-02-042-0/+124
| | | | Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
* JTAG: fix bug when no interface connectedSpencer Oliver2010-02-031-0/+7
| | | | | | - fix coredump when OpenOCD is started without a jtag interface connected. Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
* AT91R40008/Ethernut 3 configurationHarald Kipp2010-02-022-32/+95
| | | | | | | | | | Moved board specific settings from target/at91r40008.cfg to a new file board/ethernut3.cfg. Set correct CPUTAPID. Reset delay increased, see MIC2775 data sheet. Increased work area size from 16k to 128k. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
* NOR: User's Guide updatesDavid Brownell2010-02-021-6/+5
| | | | | | | | | | | | Remove long-obsolete text about "erase_check" affecting "flash info" output. Move parts of that text to "protect_check", where it's still relevant; and update the "flash info" description to mention the issue. (This is still awkward. It might be best to make "protect_check" mirror "erase_check" by dumping what it finds, so "flash info" doesn't dump any potentially-stale cache info.) Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
* tcl/str7x: Reset init unlocks the flashEdgar Grimberg2010-02-022-2/+17
| | | | | | | | | | | For STR7x flash, the device cannot be queried for the protect status. The solution is to remove the protection on reset init. The driver also initialises the sector protect field to unprotected. [dbrownell@users.sourceforge.net: line length shrinkage] Signed-off-by: Edgar Grimberg <edgar.grimberg@zylin.com> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
* flash/str7x: After reset init the flash is unlockedEdgar Grimberg2010-02-022-3/+23
| | | | | | | | | | | | | | The default state of the STR7 flash after a reset init is unlocked. The information in the flash driver now reflects this. The information about the lock status cannot be read from the flash chip, so the user is informed that flash info might not contain accurate information. [dbrownell@users.sourceforge.net: line length shrinkage] Signed-off-by: Edgar Grimberg <edgar.grimberg@zylin.com> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
* ARM semihosting: fix EOF handling with SYS_READNicolas Pitre2010-02-021-1/+1
| | | | | | | | The semihosting interface has a strange convention for read/write where the unused amount of buffer must be returned. We failed to return the total buffer size when the local read() call returned 0. Signed-off-by: Nicolas Pitre <nico@marvell.com>
* Test cases ran on v0.4.0-rc1Edgar Grimberg2010-02-015-0/+4557
| | | | | | | | | | | | | Test cases ran on v0.4.0-rc1 for a number of targets: AT91FR40162 LPC2148 SAM7 STR710 STR912 The goal of the testing session was to prove basic functionality of OpenOCD for different targets. Signed-off-by: Edgar Grimberg <edgar.grimberg@zylin.com>
* gdb: restore behavior from 0.3.1 for srst_asserted and power_restoreØyvind Harboe2010-02-012-15/+46
| | | | | | | | srst_asserted and power_restore can now be overriden to do nothing. By default they will "reset init" the targets and halt gdb. Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
* ADIv5: more messaging cleanup, docsDavid Brownell2010-01-311-12/+20
| | | | | | | | | When the TAR cache was explicitly invalidated, don't bother printing it; the actual hardware status is more informative. Provide some doxygen for the MEM-AP setup routine. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
='n1601' href='#n1601'>1601 1602 1603 1604 1605 1606 1607 1608 1609 1610 1611 1612 1613 1614 1615 1616 1617 1618 1619 1620 1621 1622 1623 1624 1625 1626 1627 1628 1629 1630 1631 1632 1633 1634 1635 1636 1637 1638 1639 1640 1641 1642 1643 1644 1645 1646 1647 1648 1649 1650 1651 1652 1653 1654 1655 1656 1657 1658 1659 1660 1661 1662 1663 1664 1665 1666 1667 1668 1669 1670 1671 1672 1673 1674 1675 1676 1677 1678 1679 1680 1681 1682 1683 1684 1685 1686 1687 1688 1689 1690 1691 1692 1693 1694 1695 1696 1697 1698 1699 1700 1701 1702 1703 1704 1705 1706 1707 1708 1709 1710 1711 1712 1713 1714 1715 1716 1717 1718 1719 1720 1721 1722 1723 1724 1725 1726 1727 1728 1729 1730 1731 1732 1733 1734 1735 1736 1737 1738 1739 1740 1741 1742 1743 1744 1745 1746 1747 1748 1749 1750 1751 1752 1753 1754 1755 1756 1757 1758 1759 1760 1761 1762 1763 1764 1765 1766 1767 1768 1769 1770 1771 1772 1773 1774 1775 1776 1777 1778 1779 1780 1781 1782 1783 1784 1785 1786 1787 1788 1789 1790 1791 1792 1793 1794 1795 1796 1797 1798 1799 1800 1801 1802 1803 1804 1805 1806 1807 1808 1809 1810 1811 1812 1813 1814 1815 1816 1817 1818 1819 1820 1821 1822 1823 1824 1825 1826 1827 1828 1829 1830 1831 1832 1833 1834 1835 1836 1837 1838 1839 1840 1841 1842 1843 1844 1845 1846 1847 1848 1849 1850 1851 1852 1853 1854 1855 1856 1857 1858 1859 1860 1861 1862 1863 1864 1865 1866 1867 1868 1869 1870 1871 1872 1873 1874 1875 1876 1877 1878 1879 1880 1881 1882 1883 1884 1885 1886 1887 1888 1889 1890 1891 1892 1893 1894 1895 1896 1897 1898 1899 1900 1901 1902 1903 1904 1905 1906 1907 1908 1909 1910 1911 1912 1913 1914 1915 1916 1917 1918 1919 1920 1921 1922 1923 1924 1925 1926 1927 1928 1929 1930 1931 1932 1933 1934 1935 1936 1937 1938 1939 1940 1941 1942 1943 1944 1945 1946 1947 1948 1949 1950 1951 1952 1953 1954 1955 1956 1957 1958 1959 1960 1961 1962 1963 1964 1965 1966 1967 1968 1969 1970 1971 1972 1973 1974 1975 1976 1977 1978 1979 1980 1981 1982 1983 1984 1985 1986 1987 1988 1989 1990 1991 1992 1993 1994 1995 1996 1997 1998 1999 2000 2001 2002 2003 2004 2005 2006 2007 2008 2009 2010 2011 2012 2013 2014 2015 2016 2017 2018 2019 2020 2021 2022 2023 2024 2025 2026 2027 2028 2029 2030 2031 2032 2033 2034 2035 2036 2037 2038 2039 2040 2041 2042 2043 2044 2045 2046 2047 2048 2049 2050 2051 2052 2053 2054 2055 2056 2057 2058 2059 2060 2061 2062 2063 2064 2065 2066 2067 2068 2069 2070 2071 2072 2073 2074 2075 2076 2077 2078 2079 2080 2081 2082 2083 2084 2085 2086 2087 2088 2089 2090 2091 2092 2093 2094 2095 2096 2097 2098 2099 2100 2101 2102 2103 2104 2105 2106 2107 2108 2109 2110 2111 2112 2113 2114 2115 2116 2117 2118 2119 2120 2121 2122 2123 2124 2125 2126 2127 2128 2129 2130 2131 2132 2133 2134 2135 2136 2137 2138 2139 2140 2141 2142 2143 2144 2145 2146 2147 2148 2149 2150 2151 2152 2153 2154 2155 2156 2157 2158 2159 2160 2161 2162 2163 2164 2165 2166 2167 2168 2169 2170 2171 2172 2173 2174 2175 2176 2177 2178 2179 2180 2181 2182 2183 2184 2185 2186 2187 2188 2189 2190 2191 2192 2193 2194 2195 2196 2197 2198 2199 2200 2201 2202 2203 2204 2205 2206 2207 2208 2209 2210 2211 2212 2213 2214 2215 2216 2217 2218 2219 2220 2221 2222 2223 2224 2225 2226 2227 2228 2229 2230 2231 2232 2233 2234 2235 2236 2237 2238 2239 2240 2241 2242 2243 2244 2245 2246 2247 2248 2249 2250 2251 2252 2253 2254 2255 2256 2257 2258 2259 2260 2261 2262 2263 2264 2265 2266 2267 2268 2269 2270 2271 2272 2273 2274 2275 2276 2277 2278 2279 2280 2281 2282 2283 2284 2285 2286 2287 2288 2289 2290 2291 2292 2293 2294 2295 2296 2297 2298 2299 2300 2301 2302 2303 2304 2305 2306 2307 2308 2309 2310 2311 2312 2313 2314 2315 2316 2317 2318 2319 2320 2321 2322 2323 2324 2325 2326 2327 2328 2329 2330 2331 2332 2333 2334 2335 2336 2337 2338 2339 2340 2341 2342 2343 2344 2345 2346 2347 2348 2349 2350 2351 2352 2353 2354 2355 2356 2357 2358 2359 2360 2361 2362 2363 2364 2365 2366 2367 2368 2369 2370 2371 2372 2373 2374 2375 2376 2377 2378 2379 2380 2381 2382 2383 2384 2385 2386 2387 2388 2389 2390 2391 2392 2393 2394 2395 2396 2397 2398 2399 2400 2401 2402 2403 2404 2405 2406 2407 2408 2409 2410 2411 2412 2413 2414 2415 2416 2417 2418 2419 2420 2421 2422 2423 2424 2425 2426 2427 2428 2429 2430 2431 2432 2433 2434 2435 2436 2437 2438 2439 2440 2441 2442 2443 2444 2445 2446 2447 2448 2449 2450 2451 2452 2453 2454 2455 2456 2457 2458 2459 2460 2461 2462 2463 2464 2465 2466 2467 2468 2469 2470 2471 2472 2473 2474 2475 2476 2477 2478 2479 2480 2481 2482 2483 2484 2485 2486 2487 2488 2489 2490 2491 2492 2493 2494 2495 2496 2497 2498 2499 2500 2501 2502 2503 2504 2505 2506 2507 2508 2509 2510 2511 2512 2513 2514 2515 2516 2517 2518 2519 2520 2521 2522 2523 2524 2525 2526 2527 2528 2529 2530 2531 2532 2533 2534 2535 2536 2537 2538 2539 2540 2541 2542 2543 2544 2545 2546 2547 2548 2549 2550 2551 2552 2553 2554 2555 2556 2557 2558 2559 2560 2561 2562 2563 2564 2565 2566 2567 2568 2569 2570 2571 2572 2573 2574 2575 2576 2577 2578 2579 2580 2581 2582 2583 2584 2585 2586 2587 2588 2589 2590 2591 2592 2593 2594 2595 2596 2597 2598 2599 2600 2601 2602 2603 2604 2605 2606 2607 2608 2609 2610 2611 2612 2613 2614 2615 2616 2617 2618 2619 2620 2621 2622 2623 2624