summaryrefslogtreecommitdiff
Commit message (Collapse)AuthorAgeFilesLines
...
* ARM11: use standard single step simulationDavid Brownell2009-11-242-99/+32
| | | | | | | | | | | | | | | | | | The previous stuff was needed because the ARM11 code wasn't using the standard ARM base type and register access ... but now those mechanisms work, so we can switch out that special-purpose glue. This should resolve all the "FIXME -- handle Thumb single stepping" comments too, and properly handle the processor's mode. (Modulo the issue that this code doesn't yet handle two-byte breakpoints.) Clarify the comments about the the hardware single stepping. When we eventually share breakpoint code with Cortex-A8, we can just make that be the default on cores which support it. We may still want an override command, not just to facilitate testing but to cope with "instruction address mismatch" not quite being true single-step. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
* ARM11: partial support for standard ARM register interfaces.David Brownell2009-11-241-35/+31
| | | | | | | | | | | | | | | | | | | | | | | | | This provides "standard" ARM register support -- with twenty or more shadow registers on top of what this code now handles, but properly associated with the various core modes -- parallel to the current register code. That is, the current code is stilil managing the "current" registers; the new code shadows them. You can see all the registers with "arm reg", modify the shadows like "r8_fiq" or "sp_abt" with "reg", and see them get properly written back when you step. (Just don't do that with any of the registers managed by the "old" code ...) It also switches to using more standard code, relying on those standard registers, in two places: (a) the poll status display, which now shows core state (ARM/Thumb/...) and mode (Supervisor, IRQ, etc); and (b) GDB register access. So it's not a full migration, there are warts -- every place that touches the old register cache is a potential bug -- but it's a small more-or-less-comprehensible step that's even somewhat useful. Later patches complete the migration. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
* ARM11: remove register "history" debug stuffDavid Brownell2009-11-242-59/+0
| | | | | | | | | | | | | | This was a private mechanism to snapshot registers before leaving debug state, and then on reentry to optionally display what changed. It was coupled to the private register cache, which won't be sticking around in that form for much longer. Remove (instead of teaching it how to handle *all* the registers). (The idea is interesting, but we ought to be able to implement this in a generic way. Ideally through Tcl scripts that can automatically be invoked following debug entry...) Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
* ARM11: implement provider for new DPM interfaceDavid Brownell2009-11-243-0/+80
| | | | | | | This is a very thin layer over some of the current ARM11 debug TAP utilities. The layer isn't yet hooked up. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
* ARM: new DPM interfaceDavid Brownell2009-11-245-0/+625
| | | | | | | | | | | | | | | | | | | First version of interface for sharing code between ARMv6 and ARMv7a debug modules ... now the architecture includes debug support. (Not the same as for the trimmed-down v7m or v6m though!) This is a first version of an interface that will let the ARM11 and Cortex-A8 support share code, features, and bugfixes. Based on existing code from both of those cores. The ARM v7-AR architecture specification calls this commonality the "Debug Programmer's Model (DPM)", which seemed to be an appropriate acronym -- a TLA even! -- for use in our code. Made it so. :) The initial scope of this just supports register access, and is geared towards supporting top level "struct arm" mechanisms. Later, things like breakpoint and watchpoint support should be included. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
* target: cope with *any* error setting a breakpointDavid Brownell2009-11-241-26/+24
| | | | | | It's wrong to map unrecognized failure codes to success. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
* support for scripts in $HOME/.openocdAndreas Fritiofson2009-11-243-9/+31
| | | | | | | | | | | | | Add $HOME/.openocd as the first default script search directory, allowing the user to override the standard scripts. Update the user guide with information on where OpenOCD expects to find configuration files and scripts. Also fixed some minor formatting issues. Add entry to NEWS as well. Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com> Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
* mips: fix gaffe when removing dynamic array allocationJerry Ling2009-11-241-3/+3
| | | | | | Classic sizeof() gaffe. Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
* arm926ejs: fix gaffe when converting from arm926ejs cp15 to mcrØyvind Harboe2009-11-233-3/+3
| | | | | | the first arg is the register number 15 = cp15. Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
* arm926ejs: retire cp15 commands, handled by mrc/mcr.Øyvind Harboe2009-11-235-76/+3
| | | | Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
* ARM11: remove unused state and exportsDavid Brownell2009-11-224-32/+25
| | | | | | | | | For now there's no point in saving this stuff after examine() checks it out as OK. Ditto exporting symbols that aren't used outside of the module which defines them. In fact, those two things needlessly complicate the code... Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
* ARM11: macro cleanupDavid Brownell2009-11-222-72/+39
| | | | | | | | | | | | | | | | | Make this code look more like the rest of the OpenOCD code. - Use calloc() directly, not NEW() ... and fix some potential memory leaks while we're at it. - Remove FNC_INFO ... it's a NOP that just clutters things, and it's trivial for developers to add tracing as needed. - Replace FNC_INFO_NOTIMPLEMENTED with LOG_WARNING calls; ditto. And stop having those call sites wrongly succeed! - Waste less space with the CHECK_RETVAL() macro. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
* mips: remove dynamic arrays - reduces stack usageØyvind Harboe2009-11-221-5/+15
| | | | | | Allocate working memory dynamically. Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
* mips: use const for code sequencesØyvind Harboe2009-11-222-13/+13
| | | | | | | | This will allow data to be allocated in read only memory instead of on the stack. Speeds things up and reduces stack usage. Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
* arm11: do not use dynamic arraysØyvind Harboe2009-11-222-4/+8
| | | | | | Allocate working memory dynamically, caught by checkstack.pl Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
* arm926ejs: fix warningsØyvind Harboe2009-11-221-2/+2
| | | | | | | | buf_set_u32() operated on an uninitialized stack variable with non-byte boundaries, which led to warnings about reading uninitialized stack. Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
* TODO: ref 'checkstack.pl' not 'checkpatch.pl'David Brownell2009-11-221-2/+2
| | | | Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
* ARM: use arm_reg_current()David Brownell2009-11-223-61/+74
| | | | | | | | | | Start using the arm_reg_current() call. This shrinks and speeds the affected code. It can also prevent some coredumps coming from invalid CPSR values ... the ARMV4_5_CORE_REG_MODE() macro returns bogus registers if e.g. "Secure Monitor" mode isn't supported by the current CPU. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
* ARM11: remove needless string format #ifdefferyDavid Brownell2009-11-223-21/+22
| | | | | | | | We don't need to use size_t in these places; so it's easy to be rid of the need for this #ifdef and its MS-derived portability problems. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
* target: make register flags "bool"David Brownell2009-11-221-2/+2
| | | | | | Mostly for clarity, but it also saves code and data space. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
* ARM: remove 'armv4_5_common_s' migration #defineDavid Brownell2009-11-2212-56/+53
| | | | | | Finish migrating from the old symbol to the new one. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
* flash: dynamically allocate working storageØyvind Harboe2009-11-221-16/+52
| | | | | | Allocate working memory rather than using stack. Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
* target: reduce stack usageØyvind Harboe2009-11-221-6/+20
| | | | | | | 4096 byte buffer allocated dynamically. Better for embedded OS's. Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
* todo: add tip on how to identify excessive stack usageØyvind Harboe2009-11-221-0/+16
| | | | | | Use dynamic allocations for working memory rather than stack. Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
* zy1000: un-break uart command after command handler refactoringØyvind Harboe2009-11-221-15/+19
| | | | | | Switched it to jim command to insulate it from command refactoring. Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
* embedded: reduce stack usageØyvind Harboe2009-11-221-4/+9
| | | | | | | Allocate working structures on stack to avoid issues with path lengths + reduce stack usage. Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
* embedded: do not allocate large temporary structures on stackØyvind Harboe2009-11-221-6/+61
| | | | | | | With -O3 when inlining aggressively the total stack usage will be the sum of many fn's, which can easily get out of hand. Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
* embedded: save stackØyvind Harboe2009-11-221-9/+15
| | | | | | | and also do not recaluate the crc32_table upon every invocation. Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
* zy1000: fix breakage in command parsing code for power commandØyvind Harboe2009-11-221-1/+1
| | | | Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
* build: fix breakage in building bin2charØyvind Harboe2009-11-221-1/+1
| | | | | | | bin2char build relied on $(builddir) which is not defined for arm-elf X builds at least. Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
* ARM: arm_set_cpsr() handles T and J bitsDavid Brownell2009-11-227-79/+52
| | | | | | | | | | | | | | Have arm_set_cpsr() handle the two core state flags, updating the CPU state. This eliminates code in various debug_entry() paths, and marginally improves handling of the J bit. Catch and comment a few holes in the handling of the J bit on ARM926ejs cores ... it's unlikely our users will care about Jazelle mode, but we can at least warn of Impending Doom. If anyone does use it, these breadcrumbs may help them to find the right path through the code. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
* ARM: define two register utilitiesDavid Brownell2009-11-228-48/+122
| | | | | | | | | | | | | | Define arm_reg_current() ... returning handle to a given register, and encapsulating the current mode's register shadowing. It's got one current use, for reporting the current register set to GDB. This will let later patches clean up much ARMV4_5_CORE_REG_MODE() nastiness, saving a bit of code. Define and use arm_set_cpsr() ... initially it updates the cached CPSR and sets up state used by arm_reg_current(), plus any SPSR handle. (Later: can also set up for T and J bits.) Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
* ARM: simplify CPSR handlingDavid Brownell2009-11-2211-87/+103
| | | | | | | | | | | | | | Stash a pointer to the CPSR in the "struct arm", to help get rid of the (common) references to its index in the register cache. This removes almost all references to CPSR offsets outside of the toplevel ARM code ... except a pair related to the current ARM11 "simulator" logic (which should be removable soonish). This is a net minor code shrink of a few hundred bytes of object code, and also makes the code more readable. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
* ARM11: remove disabled register hooksDavid Brownell2009-11-222-93/+3
| | | | | | | | Minor cleanup of ARM11 register handling: remove disabled register hooks. This should all be handled by shared code, and this stuff is just clutter. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
* jtag: remove useless forward declarationsZachary T Welch2009-11-215-140/+76
| | | | | Removes some more useless forward declarations from a few JTAG drivers. Moves interface and bit-bang structure defitions below their callbacks.
* allow jtag interfaces to lack commandsZachary T Welch2009-11-211-2/+5
| | | | | Allow JTAG interface drivers to skip registering an register_commands callback when it will just be empty.
* show script search dirs in debug logAndreas Fritiofson2009-11-211-0/+2
| | | | | | | | | | Add this to ease debugging why the standard scripts aren't found on the default script search path in some build/install enviroments. Especially on Windows it's not straight forward where openocd actually looks for the scripts. Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
* ARM: pass 'struct reg *' to register r/w routinesDavid Brownell2009-11-208-73/+83
| | | | | | | | | | | | | | | | Implementations need to access the register struct they modify; make it easier and less error-prone to identify the instance. (This removes over 10% of the ARMV4_5_CORE_REG_MODE nastiness...) Plus some minor fixes noted when making these updates: ARM7/ARM9 accessor methods should be static; don't leave CPSR wrongly marked "dirty"; note significant XScale omissions in register handling; and have armv4_5_build_reg_cache() record its result. Rename "struct armv4_5_core_reg" as "struct arm_reg"; it's used for more than those older architecture generations. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
* ARM7/ARM9: remove old "debug commands"David Brownell2009-11-202-182/+35
| | | | | | | | | | | | | | | Remove two commands that were documented as "debug commands" and where "you probably don't want to use this". We never intended to support them, and at least one problem report boiled down to using this when it shouldn't have been used. Update the docs on the existing register commands to talk a bit more about register access and cache behavior. (Those debug commands existed largely to *bypass* the cache.) And fix some minor doc goofs that snuck in with recent changes, renaming "armv4_5" as "arm" and "arm9tdmi" as "arm9". Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
* maintain command lists in sorted orderZachary T Welch2009-11-201-7/+17
| | | | | Use insertion sort to the command link lists. The only practical effect of this is to order the output of the new 'help' command.
* add add_help_text command handlerZachary T Welch2009-11-202-44/+67
| | | | | | | | | | Rewrite means for scripts to register help text for commands. These cause the new commands to be stored in the command heirarchy, with built-in commands; however, they will never be invoked there because they do not receive a command handler. The same trick is used for the Jim commands. Remove the old helpers that were used to register commands.
* provide command context during cmd_initZachary T Welch2009-11-201-0/+2
| | | | | | For the startup.tcl code to use built-in commands, the context must be associated with the interpreter temporarily. This will be required to add help text.
* improve 'help' commandZachary T Welch2009-11-203-20/+55
| | | | | | | | | | | Rewrites 'help' command in C, using new 'cmd_help' for display. Adds the built-in 'help' COMMAND_HANDLER to provide better output than the TCL-based script command (e.g. heirarchical listing of commands). The help string is stored in the command structure, though it conitnues to be pushed into the Jim environment. The current idiomatic usage suggests the addition of a usage field as well, to provide two levels of detail for users to consume (i.e. terse usage list, or verbose help).
* factor help script command into partsZachary T Welch2009-11-201-28/+34
| | | | | | | | Creates a helper function, cmd_help, which displays the help string for a single command. Presently, it is called from the loop in help. The routine has been extended to allow indentation of command groups, so an improved help command can improve the display of information.
* refactor command registrationZachary T Welch2009-11-203-83/+118
| | | | | | | | | Refactors the command registration to use helpers to simplify the code. The unregistration routines were made more flexible by allowing them to operate on a single command, such that one can remove all of a commands children in one step (perhaps before adding back a 'config' subcommand that allows getting the others back). Eliminates a bit of duplicated code and adds full API documentation for these routines.
* change command_find helper interfaceZachary T Welch2009-11-201-4/+3
| | | | Avoid requiring double pointers where a single would suffice.
* factor script_command argv allocationZachary T Welch2009-11-201-27/+38
| | | | Splits argument allocation out from script command, reusing free() code.
* target.cfg: TAP id for Hilscher netX 500David Brownell2009-11-202-9/+15
| | | | | | Based on email from "Martin Kaul <martin.kaul@leuze.de>". Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
* fix flash/nand name parsingZachary T Welch2009-11-201-1/+3
| | | | | Start driver.num check from end, and make sure the numeric part is actually a number. Fix problems trying to parse bank names.
* Cortex-A8: better context restoreDavid Brownell2009-11-191-13/+67
| | | | | | | The previous version never wrote dirty registers for non-current CPU modes ... fix that. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
generated by cgit v1.2.3 (git 2.46.0) at 2024-11-05 14:49:06 +0000