| Commit message (Collapse) | Author | Age | Files | Lines |
... | |
|
|
|
|
|
|
|
|
| |
- fixed some compiler warnigns in amt_jtagaccel.c, bitbang.c, parport.c
- free working area and register stuff if str7x block write algorithm failed
- check PC after exiting a target algorithm in armv4_5.c
git-svn-id: svn://svn.berlios.de/openocd/trunk@135 b42882b7-edfa-0310-969c-e2dbd0fdcd60
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
configuration, too) should now go through the fileio subsystem
- added support for reading IHEX files (through fileio)
- load/dump_binary renamed to the more generic load/dump_image <file> <address> ['bin'|'ihex']
- added NAND framework (preliminary)
- added support for the LPC3180 SLC and MLC NAND controllers (preliminary)
- fix initialization for parport
- gw16012 fixes/cleanups
- added EmbeddedICE version 7 (preliminary, reported on two LPC23xx devices so far)
- added 'arm7_9 etm <target#>' configuration command to enable access to the ETM registers
git-svn-id: svn://svn.berlios.de/openocd/trunk@132 b42882b7-edfa-0310-969c-e2dbd0fdcd60
|
|
|
|
|
|
|
|
| |
- complain about identify_chain scan with all bits one (jtag communication problem)
- add 0x80000 as a valid size for lpc2000_v2 flash banks (previously only the user accessible 0x7d000 were valid)
git-svn-id: svn://svn.berlios.de/openocd/trunk@129 b42882b7-edfa-0310-969c-e2dbd0fdcd60
|
|
|
|
| |
git-svn-id: svn://svn.berlios.de/openocd/trunk@123 b42882b7-edfa-0310-969c-e2dbd0fdcd60
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
- fixed bug in jtag.c where JTAG command type was wrong for PATHMOVE commands
- added lattice ISP cable (experimental)
- properly initialize parallel port (clear tristate bit)
- fixed jtag/Makefile.am that failed with some versions of autotools
- print error number if read() in gdbserver.c failed on Windows
- fixed handling of opcodes with bits 27-25 b011 (comment was correct, code had a bug)
- added support for AT91SAM7SE internal flash
git-svn-id: svn://svn.berlios.de/openocd/trunk@122 b42882b7-edfa-0310-969c-e2dbd0fdcd60
|
|
|
|
|
|
|
|
|
|
| |
jtag_interface_t.support_pathmove (it is used to indicate jtag_add_pathmove support)
- fixed small bug in str7x.c that printed an address instead of the target number in an error message
- added support for Olimex ARM-USB-OCD. The new ft2232 layout is called "olimex-jtag"
git-svn-id: svn://svn.berlios.de/openocd/trunk@87 b42882b7-edfa-0310-969c-e2dbd0fdcd60
|
|
|
|
|
|
|
|
|
| |
/dev/parport on linux) (thanks to Darius for this patch)
- unified 'ftd2xx' and 'ftdi2232' into a single interface 'ft2232'. The library used to access the hardware is choosen during configure with --enable-ft2232_ftd2xx or --enable-ft2232-libftdi.
git-svn-id: svn://svn.berlios.de/openocd/trunk@83 b42882b7-edfa-0310-969c-e2dbd0fdcd60
|
|
|
|
|
|
|
|
|
|
|
| |
reset circuitry keeps lines asserted for too long.
- additional debug output when opening the parallel port
- fixed counting of available arm7/9 watchpoint units
- 'flash write' now displays elapsed time
git-svn-id: svn://svn.berlios.de/openocd/trunk@79 b42882b7-edfa-0310-969c-e2dbd0fdcd60
|
|
|
|
|
|
|
|
|
|
| |
Michael Fischer) - you still need to install GiveIO (not part of OpenOCD)
- Added state-move support to ftd2xx and bitbang JTAG drivers (required for XScale, possibly useful for other targets, too)
- various fixes
git-svn-id: svn://svn.berlios.de/openocd/trunk@78 b42882b7-edfa-0310-969c-e2dbd0fdcd60
|
|
git-svn-id: svn://svn.berlios.de/openocd/trunk@64 b42882b7-edfa-0310-969c-e2dbd0fdcd60
|