| Commit message (Collapse) | Author | Age | Files | Lines |
|
|
|
|
|
| |
clutters config scripts.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
This patch adds support for the omapl138 target and preliminary support for the da850evm. The
target cfg file is based on the icepick routing done by the target/ti_dm6446.cfg file.
I have performed limited testing with this setup. I am posting this patch in the interest of
sharing cfg files and in the hopes that the experts on this list can correct errors I have made or
point out enhancements.
The testing I have performed is debugging uboot with gdb where I also use the following local.cfg
and gdbinit files. Debugging appears to work in so much as 'ni' works.
local.cfg:
gdb_memory_map disable
gdbinit:
target remote localhost:3333
set remote hardware-breakpoint-limit 2
set remote hardware-watchpoint-limit 2
monitor poll on
Comments welcome.
Best Regards,
Ben Gardiner
|
|
|
|
|
|
| |
rclk = 4MHz oon lpc1768, the correct JTAG clk is 666MHz(4MHz/6).
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
|
|
|
|
|
|
|
|
|
| |
srst_pulls_trst is only true on some (broken) LPC2148 boards, a fact
which is already documented in doc/openocd.texi, so it shouldn't be
set unconditionally in the target tcl.
This patch was needed to reflash when an Abort exception occured very
early after reset, before OpenOCD tried to halt the CPU.
|
|
|
|
|
|
|
| |
set user mode to avoid ROM being mapped at address
0 rather than flash.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
|
|
|
|
|
|
|
| |
There's no point in an lm3s811-specific target file,
so remove it in favor of the generic "stellaris.cfg".
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
|
|
|
|
| |
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
|
|
|
|
| |
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
|
|
|
|
|
|
|
|
| |
Added a function 'pll_v03_setup' to set up PLLs and clock
dividers on DM365 and DM368.
Signed-off-by: Thomas Koeller <thomas.koeller@baslerweb.com>
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
|
|
|
|
|
|
|
|
|
| |
Here is a patch to fix a startup in C100 (arm1136). Basically make sure
that UART is configured before using it.
Michal
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
|
|
|
|
|
|
| |
make use of the new virtual bank flash driver.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
|
|
|
|
| |
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
|
|
|
|
|
|
| |
config scripts
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
|
|
|
|
| |
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
|
|
|
|
| |
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
|
|
|
|
|
|
| |
"flash bank" parameter should be 4000 (not 12000)
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
It might be possible to get this target going without
RCLK, but it would require more careful analysis and
usage of the reset events.
Enable fast memory accesses.
Tested on an at91sam9260 custom board w/external DRAM
and flash.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
|
|
|
|
|
|
| |
Let other boards do other things with srst and trst.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
|
|
|
|
|
|
| |
As the flash bank name is now unique update the scripts to suit.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
|
|
|
|
| |
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
While "flash bank" syntax has been changed long ago,
several tcl script are still not fully update.
Fix following cases related with "cfi" driver:
- syntax error: the mandatory <name> parameter is missing
- warning: the <target> parameter is a number, instead of
the target name
- the comment line above the command does not report
actual syntax
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
|
|
|
|
|
|
|
| |
- add Microchip Explorer16 cfg using PIC32MX360F512L PIM.
- remove reset config from PIC32 target cfg.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
|
|
|
|
|
|
|
|
|
|
|
| |
Globally rename "jtag_nsrst_assert_width" as "adapter_nsrst_assert_width",
and move it out of the "jtag" command group ... it needs to be used with
non-JTAG transports
Includes a migration aid (in jtag/startup.tcl) so that old user scripts
won't break. That aid should Sunset in about a year.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
|
|
|
|
|
|
|
|
|
|
|
| |
Globally rename "jtag_nsrst_delay" as "adapter_nsrst_delay", and move it
out of the "jtag" command group ... it needs to be used with non-JTAG
transports
Includes a migration aid (in jtag/startup.tcl) so that old user scripts
won't break. That aid should Sunset in about a year.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
|
|
|
|
|
|
|
|
|
|
|
| |
Globally rename "jtag_khz" as "adapter_khz", and move it out of the "jtag"
command group ... it needs to be used with non-JTAG transports
Includes a migration aid (in jtag/startup.tcl) so that old user scripts
won't break. That aid should Sunset in about a year. (We may want to
update it to include a nag message too.)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
|
|
|
|
|
|
|
|
| |
The default config script will now dynamically setup the BMX registers
in the reset init script.
This will also work if the user overrides the default working area.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Add flash algorithm support for the PIC32MX.
Still a few things todo but this dramatically decreases
the programing time, eg. approx programming for 2.5k test file.
- without fastload: 60secs
- with fastload: 45secs
- with fastload and algorithm: 2secs.
Add new devices to supported list.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Fix some issues with the generic LPC1768 config file:
- Handle the post-reset clock config: 4 MHz internal RC, no PLL.
This affects flash and JTAG clocking.
- Remove JTAG adapter config; they don't all support trst_and_srst
- Remove the rest of the bogus "reset-init" event handler.
- Allow explicit CCLK configuration, instead of assuming 12 MHz;
some boards will use 100 Mhz (or the post-reset 4 MHz).
- Simplify: rely on defaults for endianness and IR-Capture value
- Update some comments too
Build on those fixes to make a trivial config for the IAR LPC1768
kickstart board (by Olimex) start working.
Also, add doxygen to the lpc2000 flash driver, primarily to note a
configuration problem with driver: it wrongly assumes the core clock
rate never changes. Configs that are safe for updating flash after
"reset halt" will thus often be unsafe later ... e.g. for LPC1768,
after switching to use PLL0 at 100 MHz.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The MC13224V is a FreeScale ARM7TDMI based IEEE802.15.4 platform for
Zigbee and similar low-power wireless applications. Using PIP
(Platform In Package) technology, it integrates: an RF balun and
matching network; a buck converter (only an external inductor is
necessary); 96KB of SRAM; and 128KB of non-volatile memory.
It has an integrated bootloader and can boot from a variety of sources:
external SPI or I2C non-volatile memory, an image loaded over UART1,
or the internal non-volatile memory. The image loaded from one of these
sources is executed directly from SRAM starting at location 0x00400000.
Open source development code at http://mc1322x.devl.org
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
|
|
|
|
|
|
|
|
|
| |
Cortex-M targets don't support ARM instructions.
Leave the NVIC.VTOR setup alone, but comment how the whole
routine looks like one big bug...
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
|
|
|
|
|
|
| |
JTAG.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
|
|
|
|
|
|
| |
- update str73x mem regions to correct values.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
|
|
|
|
| |
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
|
|
|
|
|
|
|
|
|
|
| |
Moved board specific settings from target/at91r40008.cfg to a new
file board/ethernut3.cfg.
Set correct CPUTAPID. Reset delay increased, see MIC2775 data sheet.
Increased work area size from 16k to 128k.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
|
|
|
|
|
|
|
|
|
|
|
| |
For STR7x flash, the device cannot be queried for the protect status.
The solution is to remove the protection on reset init. The driver
also initialises the sector protect field to unprotected.
[dbrownell@users.sourceforge.net: line length shrinkage]
Signed-off-by: Edgar Grimberg <edgar.grimberg@zylin.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The default state of the STR7 flash after a reset init is unlocked.
The information in the flash driver now reflects this.
The information about the lock status cannot be read from the
flash chip, so the user is informed that flash info might not
contain accurate information.
[dbrownell@users.sourceforge.net: line length shrinkage]
Signed-off-by: Edgar Grimberg <edgar.grimberg@zylin.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
|
|
|
|
|
|
|
|
| |
openocd does not start with the target configfile due to the case in the
dependent config file.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
|
|
|
|
|
|
| |
add reset-init script to allow ram execution from reset, this is required for ejtag fastdata access.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
|
|
|
|
| |
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Remove more remnants of the old "jtag_device" syntax.
Don't [format "%s.cpu" $_CHIPNAME] ... it's needless complexity.
Remove various non-supported "-variant" target options; they're not
needed often at all.
Flag some of the board files as needing to have and use target files
for the TAP and target declarations.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
|
|
|
|
|
|
|
| |
That syntax has been obsolete forever and is now gone; remove a few
remaining references. Shows how seldom this stuff gets used.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
|
| |
|
|
|
|
|
|
| |
reset init/run now works again.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
|
|
|
|
|
|
| |
Use the new file, and remove the old target/lm3s3748.cfg one.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
|
|
|
|
|
|
|
|
|
| |
Common target.cfg file for LM3S CPU family
[dbrownell@users.sourceforge.net: rename, generalize more]
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
|
|
|
|
|
|
|
|
|
| |
Behave like OMAP3530: force global software reset. Given the
patch to teach ARM11 how to use these events, and use VCR to
catch the reset vector, this works better than either the
current reset logic or than using SRST.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
|
|
|
|
|
|
| |
Make them match the C code.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
|
|
|
|
|
|
|
| |
Also updated to use target name when creating flash
and set jtag_khz to 16000.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
|
|
|
|
|
|
| |
[dbrownell@users.sourceforge.net; remove pxa255 comment]
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
|
|
|
|
|
|
| |
Replaces previous "reset-assert-pre" workaround.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
|