From 140d6c8e7948710a764965075bfaa700efd09802 Mon Sep 17 00:00:00 2001 From: zwelch Date: Wed, 27 May 2009 06:44:43 +0000 Subject: Move TCL script files -- Step 1 of 2: - Move src/target/{interface,target,board,test}/ into src/tcl/ - Remove existing rules in src/Makefile.am and src/target/Makefile.am. - Add Makefile.am handling of *.cfg and *.tcl files in top Makefile.am: - Add dist-hook to include such files under src/tcl in the distribution. - Add install-data-hook to install contents of '$(top_srcdir)/src/tcl/'. - Add uninstall-hook to remove the installed script files. - Change paths to (un)install script files in '$(pkgdatadir)/scripts'. git-svn-id: svn://svn.berlios.de/openocd/trunk@1918 b42882b7-edfa-0310-969c-e2dbd0fdcd60 --- src/target/board/digi_connectcore_wi-9c.cfg | 127 ---------------------------- 1 file changed, 127 deletions(-) delete mode 100644 src/target/board/digi_connectcore_wi-9c.cfg (limited to 'src/target/board/digi_connectcore_wi-9c.cfg') diff --git a/src/target/board/digi_connectcore_wi-9c.cfg b/src/target/board/digi_connectcore_wi-9c.cfg deleted file mode 100644 index 93317327..00000000 --- a/src/target/board/digi_connectcore_wi-9c.cfg +++ /dev/null @@ -1,127 +0,0 @@ -###################################### -# Target: DIGI ConnectCore Wi-9C -###################################### - -reset_config trst_and_srst - -if { [info exists CHIPNAME] } { - set _CHIPNAME $CHIPNAME -} else { - set _CHIPNAME ns9360 -} - -if { [info exists ENDIAN] } { - set _ENDIAN $ENDIAN -} else { - # This config file was defaulting to big endian.. - set _ENDIAN big -} - - -# What's a good fallback frequency for this board if RCLK is -# not available?? -jtag_rclk 1000 - - -if { [info exists CPUTAPID ] } { - set _CPUTAPID $CPUTAPID -} else { - set _CPUTAPID 0xFFFFFFFF -} - -set _TARGETNAME [format "%s.cpu" $_CHIPNAME] -jtag newtap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_CPUTAPID - -jtag_nsrst_delay 200 -jtag_ntrst_delay 0 - - -###################### -# Target configuration -###################### - -target create $_TARGETNAME arm926ejs -endian $_ENDIAN -chain-position $_TARGETNAME -variant arm926ejs -$_TARGETNAME configure -event reset-init { - mww 0x90600104 0x33313333 - mww 0xA0700000 0x00000001 # Enable the memory controller. - mww 0xA0700024 0x00000006 # Set the refresh counter 6 - mww 0xA0700028 0x00000001 # - mww 0xA0700030 0x00000001 # Set the precharge period - mww 0xA0700034 0x00000004 # Active to precharge command period is 16 clock cycles - mww 0xA070003C 0x00000001 # tAPR - mww 0xA0700040 0x00000005 # tDAL - mww 0xA0700044 0x00000001 # tWR - mww 0xA0700048 0x00000006 # tRC 32 clock cycles - mww 0xA070004C 0x00000006 # tRFC 32 clock cycles - mww 0xA0700054 0x00000001 # tRRD - mww 0xA0700058 0x00000001 # tMRD - mww 0xA0700100 0x00004280 # Dynamic Config 0 (cs4) - mww 0xA0700120 0x00004280 # Dynamic Config 1 (cs5) - mww 0xA0700140 0x00004280 # Dynamic Config 2 (cs6) - mww 0xA0700160 0x00004280 # Dynamic Config 3 (cs7) - # - mww 0xA0700104 0x00000203 # CAS latency is 2 at 100 MHz - mww 0xA0700124 0x00000203 # CAS latency is 2 at 100 MHz - mww 0xA0700144 0x00000203 # CAS latency is 2 at 100 MHz - mww 0xA0700164 0x00000203 # CAS latency is 2 at 100 MHz - # - mww 0xA0700020 0x00000103 # issue SDRAM PALL command - # - mww 0xA0700024 0x00000001 # Set the refresh counter to be as small as possible - # - # Add some dummy writes to give the SDRAM time to settle, it needs two - # AHB clock cycles, here we poke in the debugger flag, this lets - # the software know that we are in the debugger - mww 0xA0900000 0x00000002 - mww 0xA0900000 0x00000002 - mww 0xA0900000 0x00000002 - mww 0xA0900000 0x00000002 - mww 0xA0900000 0x00000002 - # - mdw 0xA0900000 - mdw 0xA0900000 - mdw 0xA0900000 - mdw 0xA0900000 - mdw 0xA0900000 - # - mww 0xA0700024 0x00000030 # Set the refresh counter to 30 - mww 0xA0700020 0x00000083 # Issue SDRAM MODE command - # - # Next we perform a read of RAM. - # mw = move word. - mdw 0x00022000 - # mw 0x00022000:P, r3 # 22000 for cas2 latency, 32000 for cas 3 - # - mww 0xA0700020 0x00000003 # issue SDRAM NORMAL command - mww 0xA0700100 0x00084280 # Enable buffer access - mww 0xA0700120 0x00084280 # Enable buffer access - mww 0xA0700140 0x00084280 # Enable buffer access - mww 0xA0700160 0x00084280 # Enable buffer access - - #Set byte lane state (static mem 1)" - mww 0xA0700220, 0x00000082 - #Flash Start - mww 0xA09001F8, 0x50000000 - #Flash Mask Reg - mww 0xA09001FC, 0xFF000001 - mww 0xA0700028, 0x00000001 - - # RAMAddr = 0x00020000 - # RAMSize = 0x00004000 - - # Set the processor mode - reg cpsr 0xd3 -} - -$_TARGETNAME configure -work-area-virt 0 -work-area-phys 0x00000000 -work-area-size 0x1000 -work-area-backup 1 - -##################### -# Flash configuration -##################### - -#M29DW323DB - not working -#flash bank cfi -flash bank cfi 0x50000000 0x0400000 2 2 0 - - - -- cgit v1.2.3