From 140d6c8e7948710a764965075bfaa700efd09802 Mon Sep 17 00:00:00 2001 From: zwelch Date: Wed, 27 May 2009 06:44:43 +0000 Subject: Move TCL script files -- Step 1 of 2: - Move src/target/{interface,target,board,test}/ into src/tcl/ - Remove existing rules in src/Makefile.am and src/target/Makefile.am. - Add Makefile.am handling of *.cfg and *.tcl files in top Makefile.am: - Add dist-hook to include such files under src/tcl in the distribution. - Add install-data-hook to install contents of '$(top_srcdir)/src/tcl/'. - Add uninstall-hook to remove the installed script files. - Change paths to (un)install script files in '$(pkgdatadir)/scripts'. git-svn-id: svn://svn.berlios.de/openocd/trunk@1918 b42882b7-edfa-0310-969c-e2dbd0fdcd60 --- src/tcl/target/lpc2378.cfg | 49 ++++++++++++++++++++++++++++++++++++++++++++++ 1 file changed, 49 insertions(+) create mode 100644 src/tcl/target/lpc2378.cfg (limited to 'src/tcl/target/lpc2378.cfg') diff --git a/src/tcl/target/lpc2378.cfg b/src/tcl/target/lpc2378.cfg new file mode 100644 index 00000000..16232383 --- /dev/null +++ b/src/tcl/target/lpc2378.cfg @@ -0,0 +1,49 @@ +# NXP LPC2378 ARM7TDMI-S with 512kB Flash and 32kB Local On-Chip SRAM (58kB total), clocked with 4MHz internal RC oscillator + +if { [info exists CHIPNAME] } { + set _CHIPNAME $CHIPNAME +} else { + set _CHIPNAME lpc2378 +} + +if { [info exists ENDIAN] } { + set _ENDIAN $ENDIAN +} else { + set _ENDIAN little +} + +if { [info exists CPUTAPID ] } { + set _CPUTAPID $CPUTAPID +} else { + set _CPUTAPID 0x4f1f0f0f +} + +#delays on reset lines +jtag_nsrst_delay 200 +jtag_ntrst_delay 200 + +# LPC2000 -> SRST causes TRST +reset_config trst_and_srst srst_pulls_trst + +jtag newtap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_CPUTAPID + +set _TARGETNAME [format "%s.cpu" $_CHIPNAME] +target create $_TARGETNAME arm7tdmi -endian $_ENDIAN -chain-position $_TARGETNAME -variant arm7tdmi-s_r4 + +# LPC2378 has 32kB of SRAM on its main system bus (so-called Local On-Chip SRAM) +$_TARGETNAME configure -work-area-virt 0 -work-area-phys 0x40000000 -work-area-size 0x8000 -work-area-backup 0 + +$_TARGETNAME configure -event reset-init { + # Force target into ARM state + soft_reset_halt + #do not remap 0x0000-0x0020 to anything but the flash + mwb 0xE01FC040 0x01 +} + +# LPC2378 has 512kB of FLASH, but upper 8kB are occupied by bootloader. +# After reset the chip uses its internal 4MHz RC oscillator +#flash bank lpc2000 0 0 +flash bank lpc2000 0x0 0x0007D000 0 0 0 lpc2000_v2 4000 calc_checksum + +# 4MHz / 6 = 666kHz, so use 500 +jtag_khz 500 -- cgit v1.2.3