From 26807d1935165160031de766c80c0e6e84604c9f Mon Sep 17 00:00:00 2001
From: oharboe <oharboe@b42882b7-edfa-0310-969c-e2dbd0fdcd60>
Date: Mon, 22 Jun 2009 17:31:12 +0000
Subject: David Brownell <david-b@pacbell.net> target config file for newish
 DM365 chip.  Think of this as an improved DM355, integrating much better HD
 video support, Ethernet, and other goodies.

git-svn-id: svn://svn.berlios.de/openocd/trunk@2351 b42882b7-edfa-0310-969c-e2dbd0fdcd60
---
 tcl/target/ti_dm365.cfg | 97 +++++++++++++++++++++++++++++++++++++++++++++++++
 1 file changed, 97 insertions(+)
 create mode 100644 tcl/target/ti_dm365.cfg

(limited to 'tcl')

diff --git a/tcl/target/ti_dm365.cfg b/tcl/target/ti_dm365.cfg
new file mode 100644
index 00000000..f889432b
--- /dev/null
+++ b/tcl/target/ti_dm365.cfg
@@ -0,0 +1,97 @@
+#
+# Texas Instruments DaVinci family:  TMS320DM365
+#
+if { [info exists CHIPNAME] } {
+   set  _CHIPNAME $CHIPNAME
+} else {
+   set  _CHIPNAME dm365
+}
+
+#
+# For now, expect EMU0/EMU1 jumpered LOW (not TI's default) so ARM and ETB
+# are enabled without making ICEpick route ARM and ETB into the JTAG chain.
+#
+# Also note:  when running without RTCK before the PLLs are set up, you
+# may need to slow the JTAG clock down quite a lot (under 2 MHz).
+#
+source [find target/icepick.cfg]
+set EMU01 "-enable"
+#set EMU01 "-disable"
+
+# Subsidiary TAP: ARM ETB11, with scan chain for 4K of ETM trace buffer
+if { [info exists ETB_TAPID ] } {
+   set _ETB_TAPID $ETB_TAPID
+} else {
+   set _ETB_TAPID 0x2b900f0f
+}
+jtag newtap $_CHIPNAME etb -irlen 4 -ircapture 0x1 -irmask 0xf \
+	-expected-id $_ETB_TAPID $EMU01
+jtag configure $_CHIPNAME.etb -event tap-enable \
+	"icepick_c_tapenable $_CHIPNAME.jrc 1"
+
+# Subsidiary TAP: ARM926ejs with scan chains for ARM Debug, EmbeddedICE-RT, ETM.
+if { [info exists CPU_TAPID ] } {
+   set _CPU_TAPID $CPU_TAPID
+} else {
+   set _CPU_TAPID 0x0792602f
+}
+jtag newtap $_CHIPNAME arm -irlen 4 -ircapture 0x1 -irmask 0xf \
+	-expected-id $_CPU_TAPID $EMU01
+jtag configure $_CHIPNAME.arm -event tap-enable \
+	"icepick_c_tapenable $_CHIPNAME.jrc 0"
+
+# Primary TAP: ICEpick (JTAG route controller) and boundary scan
+if { [info exists JRC_TAPID ] } {
+   set _JRC_TAPID $JRC_TAPID
+} else {
+   set _JRC_TAPID 0x0b83e02f
+}
+jtag newtap $_CHIPNAME jrc -irlen 6 -ircapture 0x1 -irmask 0x3f \
+	-expected-id $_JRC_TAPID
+
+################
+
+# various symbol definitions, to avoid hard-wiring addresses
+# and enable some sharing of DaVinci-family utility code
+global dm365
+set dm365 [ dict create ]
+
+# Physical addresses for controllers and memory
+# (Some of these are valid for many DaVinci family chips)
+dict set dm365 sram0		0x00010000
+dict set dm365 sram1		0x00014000
+dict set dm365 sysbase		0x01c40000
+dict set dm365 pllc1		0x01c40800
+dict set dm365 pllc2		0x01c40c00
+dict set dm365 psc		0x01c41000
+dict set dm365 gpio		0x01c67000
+dict set dm365 a_emif		0x01d10000
+dict set dm365 a_emif_cs0	0x02000000
+dict set dm365 a_emif_cs1	0x04000000
+dict set dm365 ddr_emif		0x20000000
+dict set dm365 ddr		0x80000000
+
+source [find target/davinci.cfg]
+
+################
+# GDB target:  the ARM, using SRAM1 for scratch.  SRAM0 (also 16K)
+# and the ETB memory (4K) are other options, while trace is unused.
+set _TARGETNAME $_CHIPNAME.arm
+
+target create $_TARGETNAME arm926ejs -chain-position $_TARGETNAME
+
+# NOTE that work-area-virt presumes a Linux 2.6.30-rc2+ kernel,
+# and that the work area is used only with a kernel mmu context ...
+$_TARGETNAME configure \
+	-work-area-virt [expr 0xfffe0000 + 0x4000] \
+	-work-area-phys [dict get $dm365 sram1] \
+	-work-area-size 0x4000 \
+	-work-area-backup 0
+
+arm7_9 dbgrq enable
+arm7_9 fast_memory_access enable
+arm7_9 dcc_downloads enable
+
+# trace setup
+etm config $_TARGETNAME 16 normal full etb
+etb config $_TARGETNAME $_CHIPNAME.etb
-- 
cgit v1.2.3