From bef37ceba2bde6a34d003762bced007bed894bc7 Mon Sep 17 00:00:00 2001 From: Edgar Grimberg Date: Fri, 29 Jan 2010 09:46:11 +0100 Subject: Test cases ran on v0.4.0-rc1 Test cases ran on v0.4.0-rc1 for a number of targets: AT91FR40162 LPC2148 SAM7 STR710 STR912 The goal of the testing session was to prove basic functionality of OpenOCD for different targets. Signed-off-by: Edgar Grimberg --- testing/results/v0.4.0-rc1/AT91FR40162.html | 856 +++++++++++++++++++++++ testing/results/v0.4.0-rc1/LPC2148.html | 933 +++++++++++++++++++++++++ testing/results/v0.4.0-rc1/SAM7.html | 853 +++++++++++++++++++++++ testing/results/v0.4.0-rc1/STR710.html | 907 ++++++++++++++++++++++++ testing/results/v0.4.0-rc1/STR912.html | 1008 +++++++++++++++++++++++++++ 5 files changed, 4557 insertions(+) create mode 100755 testing/results/v0.4.0-rc1/AT91FR40162.html create mode 100755 testing/results/v0.4.0-rc1/LPC2148.html create mode 100755 testing/results/v0.4.0-rc1/SAM7.html create mode 100755 testing/results/v0.4.0-rc1/STR710.html create mode 100755 testing/results/v0.4.0-rc1/STR912.html (limited to 'testing') diff --git a/testing/results/v0.4.0-rc1/AT91FR40162.html b/testing/results/v0.4.0-rc1/AT91FR40162.html new file mode 100755 index 00000000..0baa31e6 --- /dev/null +++ b/testing/results/v0.4.0-rc1/AT91FR40162.html @@ -0,0 +1,856 @@ + + +Test results for revision 1.62 + + + + +

SAM7

+ +

Connectivity

+ + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + +

ID	Target	Interface	Description	Initial state	Input	Expected output	Actual output	Pass/Fail
CON001	AT91FR40162	ZY1000	Telnet connection	Power on, jtag target attached	On console, type `telnet ip port`	`Open On-Chip Debugger >`	`Open On-Chip Debugger >`	PASS
CON002	AT91FR40162	ZY1000	GDB server connection	Power on, jtag target attached	On GDB console, type `target remote ip:port`	`Remote debugging using 10.0.0.73:3333`	`+ (gdb) tar remo 10.0.0.138:3333 + Remote debugging using 10.0.0.138:3333 + 0x000155b8 in ?? () +`	PASS

+ +

Reset

+ + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + +

ID	Target	Interface	Description	Initial state	Input	Expected output	Actual output	Pass/Fail
RES001	AT91FR40162	ZY1000	Reset halt on a blank target	Erase all the content of the flash	Connect via the telnet interface and type `reset halt`	Reset should return without error and the output should contain `target state: halted`	+ + > mdw 0x01000000 32 + 0x01000000: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff + 0x01000020: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff + 0x01000040: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff + 0x01000060: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff + > reset halt + JTAG tap: zy1000.cpu tap/device found: 0x1f0f0f0f (mfg: 0x787, part: 0xf0f0, ver: 0x1) + srst pulls trst - can not reset into halted mode. Issuing halt after reset. + target state: halted + target halted in ARM state due to debug-request, current mode: Supervisor + cpsr: 0x600000d3 pc: 0x00008a70 + > + +	PASS
RES002	AT91FR40162	ZY1000	Reset init on a blank target	Erase all the content of the flash	Connect via the telnet interface and type `reset init`	Reset should return without error and the output should contain `executing reset script 'name_of_the_script'`	+ `+ > reset init + JTAG tap: zy1000.cpu tap/device found: 0x1f0f0f0f (mfg: 0x787, part: 0xf0f0, ver: 0x1) + srst pulls trst - can not reset into halted mode. Issuing halt after reset. + target state: halted + target halted in ARM state due to debug-request, current mode: Supervisor + cpsr: 0x600000d3 pc: 0x00008ea4 + > +` +	PASS + NOTE! Even if there is no message, the reset script is being executed (proved by side effects)
RES003	AT91FR40162	ZY1000	Reset after a power cycle of the target	Reset the target then power cycle the target	Connect via the telnet interface and type `reset halt` after the power was detected	Reset should return without error and the output should contain `target state: halted`	+ + Sensed nSRST asserted + Sensed power dropout. + target state: halted + target halted in ARM state due to debug request, current mode: Supervisor + cpsr: 0xf00000d3 pc: 0xd5dff7e6 + Sensed power restore. + Sensed nSRST deasserted + > reset halt + JTAG device found: 0x3f0f0f0f (Manufacturer: 0x787, Part: 0xf0f0, Version: 0x3) + srst pulls trst - can not reset into halted mode. Issuing halt after reset. + target state: halted + target halted in ARM state due to debug request, current mode: Supervisor + cpsr: 0xf00000d3 pc: 0x0000072c + > + +	PASS
RES004	AT91FR40162	ZY1000	Reset halt on a blank target where reset halt is supported	Erase all the content of the flash	Connect via the telnet interface and type `reset halt`	Reset should return without error and the output should contain `target state: halted pc = 0`	+ > reset halt + JTAG tap: zy1000.cpu tap/device found: 0x1f0f0f0f (mfg: 0x787, part: 0xf0f0, ver: 0x1) + srst pulls trst - can not reset into halted mode. Issuing halt after reset. + target state: halted + target halted in ARM state due to debug-request, current mode: Supervisor + cpsr: 0xf00000d3 pc: 0x00008b38 + > +	PASS
RES005	AT91FR40162	ZY1000	Reset halt on a blank target using return clock	Erase all the content of the flash, set the configuration script to use RCLK	Connect via the telnet interface and type `reset halt`	Reset should return without error and the output should contain `target state: halted`	+ `+ N/A, At91EB40A does NOT have support for RCLK +` +	N/A

+ +

JTAG Speed

+ + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + +

ID	Target	ZY1000	Description	Initial state	Input	Expected output	Actual output	Pass/Fail
SPD001	AT91FR40162	ZY1000	16MHz on normal operation	Reset init the target according to RES002	Change speed and exercise a memory access over the JTAG, for example `mdw 0x0 32`	The command should run without any errors. If any JTAG checking errors happen, the test failed	+ + > reset halt + JTAG tap: zy1000.cpu tap/device found: 0x1f0f0f0f (mfg: 0x787, part: 0xf0f0, ver: 0x1) + srst pulls trst - can not reset into halted mode. Issuing halt after reset. + target state: halted + target halted in ARM state due to debug-request, current mode: Supervisor + cpsr: 0xf00000d3 pc: 0x00008ae8 + > jtag_khz 16000 + jtag_speed 4 => JTAG clk=16.000000 + 16000 kHz + > mdw 0 32 + 0x00000000: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff + 0x00000020: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff + 0x00000040: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff + 0x00000060: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff + +	PASS
SPD002	AT91FR40162	ZY1000	8MHz on normal operation	Reset init the target according to RES002	Change speed and exercise a memory access over the JTAG, for example `mdw 0x0 32`	The command should run without any errors. If any JTAG checking errors happen, the test failed	+ + > reset halt + JTAG tap: zy1000.cpu tap/device found: 0x1f0f0f0f (mfg: 0x787, part: 0xf0f0, ver: 0x1) + srst pulls trst - can not reset into halted mode. Issuing halt after reset. + target state: halted + target halted in ARM state due to debug-request, current mode: Supervisor + cpsr: 0xf00000d3 pc: 0x00008c14 + > jtag_khz 8000 + jtag_speed 8 => JTAG clk=8.000000 + 8000 kHz + > mdw 0 32 + 0x00000000: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff + 0x00000020: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff + 0x00000040: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff + 0x00000060: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff + > + +	PASS
SPD003	AT91FR40162	ZY1000	4MHz on normal operation	Reset init the target according to RES002	Change speed and exercise a memory access over the JTAG, for example `mdw 0x0 32`	The command should run without any errors. If any JTAG checking errors happen, the test failed	+ + > reset halt + JTAG tap: zy1000.cpu tap/device found: 0x1f0f0f0f (mfg: 0x787, part: 0xf0f0, ver: 0x1) + srst pulls trst - can not reset into halted mode. Issuing halt after reset. + target state: halted + target halted in ARM state due to debug-request, current mode: Supervisor + cpsr: 0xf00000d3 pc: 0x00008bc4 + > jtag_khz 4000 + jtag_speed 16 => JTAG clk=4.000000 + 4000 kHz + > mdw 0 32 + 0x00000000: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff + 0x00000020: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff + 0x00000040: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff + 0x00000060: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff + > + +	PASS
SPD004	AT91FR40162	ZY1000	2MHz on normal operation	Reset init the target according to RES002	Change speed and exercise a memory access over the JTAG, for example `mdw 0x0 32`	The command should run without any errors. If any JTAG checking errors happen, the test failed	+ + > reset halt + JTAG tap: zy1000.cpu tap/device found: 0x1f0f0f0f (mfg: 0x787, part: 0xf0f0, ver: 0x1) + srst pulls trst - can not reset into halted mode. Issuing halt after reset. + target state: halted + target halted in ARM state due to debug-request, current mode: Supervisor + cpsr: 0xf00000d3 pc: 0x00009678 + > jtag_khz 2000 + jtag_speed 32 => JTAG clk=2.000000 + 2000 kHz + > mdw 0 32 + 0x00000000: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff + 0x00000020: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff + 0x00000040: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff + 0x00000060: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff + > + +	PASS
SPD005	AT91FR40162	ZY1000	RCLK on normal operation	Reset init the target according to RES002	Change speed and exercise a memory access over the JTAG, for example `mdw 0x0 32`	The command should run without any errors. If any JTAG checking errors happen, the test failed	+ `+ > jtag_khz 0 + RCLK - adaptive + RCLK timeout +` + N/A for this target +	N/A for this target

+ +

Debugging

+ + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + +

ID	Target	Interface	Description	Initial state	Input	Expected output	Actual output	Pass/Fail
DBG001	AT91FR40162	ZY1000	Load is working	Reset init is working, RAM is accesible, GDB server is started	On the console of the OS: + `$ arm-none-eabi-gdb redboot_ram.elf` + `(gdb) target remote ip:port` + `(gdb) load +`	Load should return without error, typical output looks like: + `+ Loading section .text, size 0x14c lma 0x0 + Start address 0x40, load size 332 + Transfer rate: 180 bytes/sec, 332 bytes/write. +` +	`+ (gdb) load + Loading section .rom_vectors, size 0x40 lma 0xc000 + Loading section .text, size 0x103e8 lma 0xc040 + Loading section .rodata, size 0x1a84 lma 0x1c428 + Loading section .data, size 0x3ec lma 0x1deac + Start address 0xc040, load size 74392 + Transfer rate: 572 KB/sec, 9299 bytes/write. + (gdb) +`	PASS
DBG002	AT91FR40162	ZY1000	Software breakpoint	Load the redboot_ram.elf application, use instructions from GDB001	In the GDB console: + `+ (gdb) monitor arm7_9 dbgrq enable + software breakpoints enabled + (gdb) break cyg_start + Breakpoint 1 at 0xec: file src/main.c, line 71. + (gdb) continue + Continuing. +` +	The software breakpoint should be reached, a typical output looks like: + `+ Breakpoint 1, main () at src/main.c:69 + 69 DWORD a = 1; +` +	+ `+ (gdb) monitor arm7_9 dbgrq enable + use of EmbeddedICE dbgrq instead of breakpoint for target halt enabled + (gdb) break cyg_start + + Breakpoint 1 at 0x155b8: file /home/edgar/temp/ecosboard/packages/redboot/current/src/main.c, line 264. + (gdb) continue + Continuing. + + Breakpoint 1, cyg_start () + at /home/edgar/temp/ecosboard/packages/redboot/current/src/main.c:264 + 264 CYGACC_CALL_IF_MONITOR_VERSION_SET(RedBoot_version); + (gdb) +` +	PASS
DBG003	AT91FR40162	ZY1000	Single step in a RAM application	Load the test_ram.elf application, use instructions from GDB001, break in main using the instructions from GDB002	In GDB, type `(gdb) step`	The next instruction should be reached, typical output: + `+ (gdb) step + 70 DWORD b = 2; + +` +	+ `+ (gdb) step + 266 CYGACC_CALL_IF_MONITOR_RETURN_SET(return_to_redboot); + (gdb) +` +	PASS
DBG004	AT91FR40162	ZY1000	Software break points are working after a reset	Load the test_ram.elf application, use instructions from GDB001, break in main using the instructions from GDB002	In GDB, type `+ (gdb) monitor reset init + (gdb) load + (gdb) continue +`	The breakpoint should be reached, typical output: + `+ Breakpoint 1, main () at src/main.c:69 + 69 DWORD a = 1; +` +	+ (gdb) moni reset init + JTAG tap: zy1000.cpu tap/device found: 0x1f0f0f0f (mfg: 0x787, part: 0xf0f0, ver: 0x1) + srst pulls trst - can not reset into halted mode. Issuing halt after reset. + target state: halted + target halted in ARM state due to debug-request, current mode: Supervisor + cpsr: 0x600000d3 pc: 0x00008ae8 + (gdb) load + Loading section .rom_vectors, size 0x40 lma 0xc000 + Loading section .text, size 0x103e8 lma 0xc040 + Loading section .rodata, size 0x1a84 lma 0x1c428 + Loading section .data, size 0x3ec lma 0x1deac + Start address 0xc040, load size 74392 + Transfer rate: 576 KB/sec, 9299 bytes/write. + (gdb) c + Continuing. + + Breakpoint 1, cyg_start () + at /home/edgar/temp/ecosboard/packages/redboot/current/src/main.c:264 + 264 CYGACC_CALL_IF_MONITOR_VERSION_SET(RedBoot_version); + (gdb) +	PASS
DBG005	AT91FR40162	ZY1000	Hardware breakpoint	Flash the redboot_rom.elf application. Make this test after FLA004 has passed	Be sure that `gdb_memory_map` and `gdb_flash_program` are enabled. In GDB, type + `+ (gdb) monitor reset init + (gdb) load + Loading section .text, size 0x194 lma 0x100000 + Start address 0x100040, load size 404 + Transfer rate: 179 bytes/sec, 404 bytes/write. + (gdb) monitor arm7_9 force_hw_bkpts enable + force hardware breakpoints enabled + (gdb) break main + Breakpoint 1 at 0x100134: file src/main.c, line 69. + (gdb) continue +` +	The breakpoint should be reached, typical output: + `+ Continuing. + + Breakpoint 1, main () at src/main.c:69 + 69 DWORD a = 1; +` +	+ + (gdb) load + Loading section .rom_vectors, size 0x40 lma 0x1000000 + Loading section .text, size 0x10638 lma 0x1000040 + Loading section .rodata, size 0x1a84 lma 0x1010678 + Loading section .data, size 0x428 lma 0x10120fc + Start address 0x1000040, load size 75044 + Transfer rate: 33 KB/sec, 9380 bytes/write. + (gdb) break cyg_start + Breakpoint 1 at 0x100979c: file /home/edgar/temp/ecosboard/packages/redboot/current/src/main.c, line 264. + (gdb) c + Continuing. + Note: automatically using hardware breakpoints for read-only addresses. + + Breakpoint 1, cyg_start () at /home/edgar/temp/ecosboard/packages/redboot/current/src/main.c:264 + 264 CYGACC_CALL_IF_MONITOR_VERSION_SET(RedBoot_version); + (gdb) + +	PASS
DBG006	AT91FR40162	ZY1000	Hardware breakpoint is set after a reset	Follow the instructions to flash and insert a hardware breakpoint from DBG005	In GDB, type + `+ (gdb) monitor reset + (gdb) monitor reg pc 0x100000 + pc (/32): 0x00100000 + (gdb) continue +` + where the value inserted in PC is the start address of the application +	The breakpoint should be reached, typical output: + `+ Continuing. + + Breakpoint 1, main () at src/main.c:69 + 69 DWORD a = 1; +` +	+ + (gdb) moni reset init + JTAG tap: zy1000.cpu tap/device found: 0x1f0f0f0f (mfg: 0x787, part: 0xf0f0, ver: 0x1) + srst pulls trst - can not reset into halted mode. Issuing halt after reset. + target state: halted + target halted in ARM state due to debug-request, current mode: Supervisor + cpsr: 0x200000d3 pc: 0x01000200 + (gdb) moni reg pc 0x1000000 + pc (/32): 0x01000000 + (gdb) c + Continuing. + + Breakpoint 1, cyg_start () at /home/edgar/temp/ecosboard/packages/redboot/current/src/main.c:264 + 264 CYGACC_CALL_IF_MONITOR_VERSION_SET(RedBoot_version); + (gdb) + +	PASS
DBG007	AT91FR40162	ZY1000	Single step in ROM	Flash the test_rom.elf application and set a breakpoint in main, use DBG005. Make this test after FLA004 has passed	Be sure that `gdb_memory_map` and `gdb_flash_program` are enabled. In GDB, type + `+ (gdb) monitor reset + (gdb) load + Loading section .text, size 0x194 lma 0x100000 + Start address 0x100040, load size 404 + Transfer rate: 179 bytes/sec, 404 bytes/write. + (gdb) monitor arm7_9 force_hw_bkpts enable + force hardware breakpoints enabled + (gdb) break main + Breakpoint 1 at 0x100134: file src/main.c, line 69. + (gdb) continue + Continuing. + + Breakpoint 1, main () at src/main.c:69 + 69 DWORD a = 1; + (gdb) step +` +	The breakpoint should be reached, typical output: + `+ target state: halted + target halted in ARM state due to single step, current mode: Supervisor + cpsr: 0x60000013 pc: 0x0010013c + 70 DWORD b = 2; +` +	`+ Breakpoint 1, cyg_start () at /home/edgar/temp/ecosboard/packages/redboot/current/src/main.c:264 + 264 CYGACC_CALL_IF_MONITOR_VERSION_SET(RedBoot_version); + (gdb) step + 266 CYGACC_CALL_IF_MONITOR_RETURN_SET(return_to_redboot); +`	PASS

+ +

RAM access

+Note: these tests are not designed to test/debug the target, but to test functionalities! + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + +

ID	Target	Interface	Description	Initial state	Input	Expected output	Actual output	Pass/Fail
RAM001	AT91FR40162	ZY1000	32 bit Write/read RAM	Reset init is working	On the telnet interface + `> mww ram_address 0xdeadbeef 16 + > mdw ram_address 32 +` +	The commands should execute without error. A clear failure is a memory access exception. The result of running the commands should be a list of 16 locations 32bit long containing 0xdeadbeef. + `+ > mww 0x0 0xdeadbeef 16 + > mdw 0x0 32 + 0x00000000: deadbeef deadbeef deadbeef deadbeef deadbeef deadbeef deadbeef deadbeef + 0x00000020: deadbeef deadbeef deadbeef deadbeef deadbeef deadbeef deadbeef deadbeef + 0x00000040: e1a00000 e59fa51c e59f051c e04aa000 00080017 00009388 00009388 00009388 + 0x00000060: 00009388 0002c2c0 0002c2c0 000094f8 000094f4 00009388 00009388 00009388 +` +	`+ > mww 0 0xdeadbeef 16 + > mdw 0x0 32 + 0x00000000: deadbeef deadbeef deadbeef deadbeef deadbeef deadbeef deadbeef deadbeef + 0x00000020: deadbeef deadbeef deadbeef deadbeef deadbeef deadbeef deadbeef deadbeef + 0x00000040: 15aadc6d 425b6f33 e789f955 d390dcc2 00080017 010067b4 010067b4 010067b4 + 0x00000060: 010067b4 00006e74 00006e74 010067b4 010067b4 010067b4 010067b4 010067b4 +`	PASS
RAM002	AT91FR40162	ZY1000	16 bit Write/read RAM	Reset init is working	On the telnet interface + `> mwh ram_address 0xbeef 16 + > mdh ram_address 32 +` +	The commands should execute without error. A clear failure is a memory access exception. The result of running the commands should be a list of 16 locations 16bit long containing 0xbeef. + `+ > mwh 0x0 0xbeef 16 + > mdh 0x0 32 + 0x00000000: beef beef beef beef beef beef beef beef beef beef beef beef beef beef beef beef + 0x00000020: 00e0 0000 021c 0000 0240 0000 026c 0000 0288 0000 0000 0000 0388 0000 0350 0000 + > +` +	`+ > mwh 0 0xbeef 16 + > mdh 0x0 32 + 0x00000000: beef beef beef beef beef beef beef beef beef beef beef beef beef beef beef beef + 0x00000020: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 +`	PASS There is a problem with the formatting of the output
RAM003	AT91FR40162	ZY1000	8 bit Write/read RAM	Reset init is working	On the telnet interface + `> mwb ram_address 0xab 16 + > mdb ram_address 32 +` +	The commands should execute without error. A clear failure is a memory access exception. The result of running the commands should be a list of 16 locations 8bit long containing 0xab. + `+ > mwb ram_address 0xab 16 + > mdb ram_address 32 + 0x00000000: ab ab ab ab ab ab ab ab ab ab ab ab ab ab ab ab 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 + > +` +	`+ > mwb 0x0 0xab 16 + > mdb 0x0 32 + 0x00000000: ab ab ab ab ab ab ab ab ab ab ab ab ab ab ab ab 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 +`	PASS

+ + + +

Flash access

+ + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + +

ID	Target	Interface	Description	Initial state	Input	Expected output	Actual output	Pass/Fail
FLA001	AT91FR40162	ZY1000	Flash probe	Reset init is working	On the telnet interface: + `> flash probe 0` +	The command should execute without error. The output should state the name of the flash and the starting address. An example of output: + `flash 'ecosflash' found at 0x01000000` +	+ `+ > flash probe 0 + flash 'ecosflash' found at 0x01000000 +` +	PASS
FLA002	AT91FR40162	ZY1000	flash fillw	Reset init is working, flash is probed	On the telnet interface + `> flash fillw 0x100000 0xdeadbeef 16 +` +	The commands should execute without error. The output looks like: + `+ wrote 64 bytes to 0x0100000 in 11.610000s (0.091516 kb/s) +` + To verify the contents of the flash: + `+ > mdw 0x100000 32 + 0x0100000: deadbeef deadbeef deadbeef deadbeef deadbeef deadbeef deadbeef deadbeef + 0x0100020: deadbeef deadbeef deadbeef deadbeef deadbeef deadbeef deadbeef deadbeef + 0x0100040: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff + 0x0100060: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff +` +	`+ > flash fillw 0x01000000 0xdeadbeef 16 + wrote 64 bytes to 0x01000000 in 0.010000s (6.250 kb/s) + > mdw 0x1000000 32 + 0x01000000: deadbeef deadbeef deadbeef deadbeef deadbeef deadbeef deadbeef deadbeef + 0x01000020: deadbeef deadbeef deadbeef deadbeef deadbeef deadbeef deadbeef deadbeef + 0x01000040: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff + 0x01000060: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff + > +`	PASS
FLA003	AT91FR40162	ZY1000	Flash erase	Reset init is working, flash is probed	On the telnet interface + `> flash erase_address 0x100000 0x2000 +` +	The commands should execute without error. + `+ erased address 0x0100000 length 8192 in 4.970000s +` + To check that the flash has been erased, read at different addresses. The result should always be 0xff. + `+ > mdw 0x100000 32 + 0x0100000: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff + 0x0100020: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff + 0x0100040: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff + 0x0100060: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff +` +	`+ > flash erase_address 0x1000000 0x10000 + erased address 0x01000000 (length 65536) in 0.840000s (76.190 kb/s) + > mdw 0x1000000 32 + 0x01000000: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff + 0x01000020: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff + 0x01000040: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff + 0x01000060: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff +`	PASS
FLA004	AT91FR40162	ZY1000	Loading to flash from GDB	Reset init is working, flash is probed, connectivity to GDB server is working	Start GDB using a ROM elf image, eg: arm-elf-gdb test_rom.elf. + `+ (gdb) target remote ip:port + (gdb) monitor reset halt + (gdb) load + Loading section .text, size 0x194 lma 0x100000 + Start address 0x100040, load size 404 + Transfer rate: 179 bytes/sec, 404 bytes/write. + (gdb) monitor verify_image path_to_elf_file +` +	The output should look like: + `+ verified 404 bytes in 5.060000s +` + The failure message is something like: + `Verify operation failed address 0x00200000. Was 0x00 instead of 0x18` +	+ + (gdb) load + Loading section .rom_vectors, size 0x40 lma 0x1000000 + Loading section .text, size 0x10638 lma 0x1000040 + Loading section .rodata, size 0x1a84 lma 0x1010678 + Loading section .data, size 0x428 lma 0x10120fc + Start address 0x1000040, load size 75044 + Transfer rate: 34 KB/sec, 9380 bytes/write. + (gdb) moni verify_image /tftp/10.0.0.190/redboot_rom.elf + keep_alive() was not invoked in the 1000ms timelimit. GDB alive packet not sent! (1820). Workaround: increase "set remotetimeout" in GDB + verified 75044 bytes in 1.960000s (37.390 kb/s) + +	PASS

+ + + \ No newline at end of file diff --git a/testing/results/v0.4.0-rc1/LPC2148.html b/testing/results/v0.4.0-rc1/LPC2148.html new file mode 100755 index 00000000..425b5248 --- /dev/null +++ b/testing/results/v0.4.0-rc1/LPC2148.html @@ -0,0 +1,933 @@ + + +Test results for revision 1.62 + + + + +

LPC2148

+ +

Connectivity

+ + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + +

ID	Target	Interface	Description	Initial state	Input	Expected output	Actual output	Pass/Fail
CON001	LPC2148	ZY1000	Telnet connection	Power on, jtag target attached	On console, type `telnet ip port`	`Open On-Chip Debugger >`	`Open On-Chip Debugger >`	PASS
CON002	LPC2148	ZY1000	GDB server connection	Power on, jtag target attached	On GDB console, type `target remote ip:port`	`Remote debugging using 10.0.0.73:3333`	`+ (gdb) tar remo 10.0.0.73:3333 + Remote debugging using 10.0.0.73:3333 + 0x00000000 in ?? () +`	PASS

+ +

Reset

+ + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + +

ID	Target	Interface	Description	Initial state	Input	Expected output	Actual output	Pass/Fail
RES001	LPC2148	ZY1000	Reset halt on a blank target	Erase all the content of the flash	Connect via the telnet interface and type `reset halt`	Reset should return without error and the output should contain `target state: halted`	+ + > mdw 0 32 + 0x00000000: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff + 0x00000020: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff + 0x00000040: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff + 0x00000060: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff + > reset halt + JTAG tap: lpc2148.cpu tap/device found: 0x4f1f0f0f (mfg: 0x787, part: 0xf1f0, ver: 0x4) + srst pulls trst - can not reset into halted mode. Issuing halt after reset. + target state: halted + target halted in Thumb state due to debug-request, current mode: Supervisor + cpsr: 0xa00000f3 pc: 0x7fffd2d6 + > + +	PASS
RES002	LPC2148	ZY1000	Reset init on a blank target	Erase all the content of the flash	Connect via the telnet interface and type `reset init`	Reset should return without error and the output should contain `executing reset script 'name_of_the_script'`	+ `+ > reset init + JTAG tap: lpc2148.cpu tap/device found: 0x4f1f0f0f (mfg: 0x787, part: 0xf1f0, ver: 0x4) + srst pulls trst - can not reset into halted mode. Issuing halt after reset. + target state: halted + target halted in Thumb state due to debug-request, current mode: Supervisor + cpsr: 0xa00000f3 pc: 0x7fffd2da + core state: ARM + > +` +	PASS + NOTE! Even if there is no message, the reset script is being executed (proved by side effects)
RES003	LPC2148	ZY1000	Reset after a power cycle of the target	Reset the target then power cycle the target	Connect via the telnet interface and type `reset halt` after the power was detected	Reset should return without error and the output should contain `target state: halted`	+ + nsed nSRST asserted. + nsed power dropout. + nsed power restore. + SRST took 186ms to deassert + JTAG tap: lpc2148.cpu tap/device found: 0x4f1f0f0f (mfg: 0x787, part: 0xf1f0, ver: 0x4) + srst pulls trst - can not reset into halted mode. Issuing halt after reset. + target state: halted + target halted in Thumb state due to debug-request, current mode: Supervisor + cpsr: 0xa00000f3 pc: 0x7fffd2d6 + core state: ARM + > reset halt + JTAG tap: lpc2148.cpu tap/device found: 0x4f1f0f0f (mfg: 0x787, part: 0xf1f0, ver: 0x4) + srst pulls trst - can not reset into halted mode. Issuing halt after reset. + target state: halted + target halted in Thumb state due to debug-request, current mode: Supervisor + cpsr: 0xa00000f3 pc: 0x7fffd2d6 + > + +	PASS
RES004	LPC2148	ZY1000	Reset halt on a blank target where reset halt is supported	Erase all the content of the flash	Connect via the telnet interface and type `reset halt`	Reset should return without error and the output should contain `target state: halted pc = 0`	+ `+ > reset halt + JTAG tap: lpc2148.cpu tap/device found: 0x4f1f0f0f (mfg: 0x787, part: 0xf1f0, ver: 0x4) + srst pulls trst - can not reset into halted mode. Issuing halt after reset. + target state: halted + target halted in Thumb state due to debug-request, current mode: Supervisor + cpsr: 0xa00000f3 pc: 0x7fffd2d6 + > +` +	PASS
RES005	LPC2148	ZY1000	Reset halt on a blank target using return clock	Erase all the content of the flash, set the configuration script to use RCLK	Connect via the telnet interface and type `reset halt`	Reset should return without error and the output should contain `target state: halted`	+ `+ > jtag_khz 0 + RCLK - adaptive + > reset init + JTAG tap: lpc2148.cpu tap/device found: 0x4f1f0f0f (mfg: 0x787, part: 0xf1f0, ver: 0x4) + srst pulls trst - can not reset into halted mode. Issuing halt after reset. + target state: halted + target halted in Thumb state due to debug-request, current mode: Supervisor + cpsr: 0xa00000f3 pc: 0x7fffd2d6 + core state: ARM + > +` +	PASS

+ +

JTAG Speed

+ + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + +

ID	Target	ZY1000	Description	Initial state	Input	Expected output	Actual output	Pass/Fail
SPD001	LPC2148	ZY1000	16MHz on normal operation	Reset init the target according to RES002	Change speed and exercise a memory access over the JTAG, for example `mdw 0x0 32`	The command should run without any errors. If any JTAG checking errors happen, the test failed	+ + > jtag_khz 16000 + jtag_speed 4 => JTAG clk=16.000000 + 16000 kHz + > reset halt + JTAG scan chain interrogation failed: all zeroes + Check JTAG interface, timings, target power, etc. + error: -100 + Command handler execution failed + in procedure 'reset' called at file "command.c", line 638 + called at file "/home/laurentiu/workspace/zy1000/build/../openocd/src/helper/command.c", line 352 + invalid mode value encountered 0 + cpsr contains invalid mode value - communication failure + ThumbEE -- incomplete support + target state: halted + target halted in ThumbEE state due to debug-request, current mode: System + cpsr: 0x1fffffff pc: 0xfffffffa + invalid mode value encountered 0 + cpsr contains invalid mode value - communication failure + target state: halted + target halted in Thumb state due to debug-request, current mode: System + cpsr: 0xc00003ff pc: 0xfffffff0 + invalid mode value encountered 0 + cpsr contains invalid mode value - communication failure + invalid mode value encountered 0 + cpsr contains invalid mode value - communication failure + invalid mode value encountered 0 + cpsr contains invalid mode value - communication failure + invalid mode value encountered 0 + cpsr contains invalid mode value - communication failure + ThumbEE -- incomplete support + target state: halted + target halted in ThumbEE state due to debug-request, current mode: System + cpsr: 0xffffffff pc: 0xfffffffa + > + +	FAIL
SPD002	LPC2148	ZY1000	8MHz on normal operation	Reset init the target according to RES002	Change speed and exercise a memory access over the JTAG, for example `mdw 0x0 32`	The command should run without any errors. If any JTAG checking errors happen, the test failed	+ + > jtag_khz 8000 + jtag_speed 8 => JTAG clk=8.000000 + 8000 kHz + > reset halt + JTAG scan chain interrogation failed: all zeroes + Check JTAG interface, timings, target power, etc. + error: -100 + Command handler execution failed + in procedure 'reset' called at file "command.c", line 638 + called at file "/home/laurentiu/workspace/zy1000/build/../openocd/src/helper/command.c", line 352 + invalid mode value encountered 0 + cpsr contains invalid mode value - communication failure + invalid mode value encountered 0 + cpsr contains invalid mode value - communication failure + > + +	FAIL
SPD003	LPC2148	ZY1000	4MHz on normal operation	Reset init the target according to RES002	Change speed and exercise a memory access over the JTAG, for example `mdw 0x0 32`	The command should run without any errors. If any JTAG checking errors happen, the test failed	+ + > jtag_khz 4000 + jtag_speed 16 => JTAG clk=4.000000 + 4000 kHz + > reset halt + JTAG tap: lpc2148.cpu tap/device found: 0xc79f0f87 (mfg: 0x7c3, part: 0x79f0, ver: 0xc) + JTAG tap: lpc2148.cpu UNEXPECTED: 0xc79f0f87 (mfg: 0x7c3, part: 0x79f0, ver: 0xc) + JTAG tap: lpc2148.cpu expected 1 of 1: 0x4f1f0f0f (mfg: 0x787, part: 0xf1f0, ver: 0x4) + Unexpected idcode after end of chain: 64 0x0000007f + Unexpected idcode after end of chain: 160 0x0000007f + Unexpected idcode after end of chain: 192 0x0000007f + Unexpected idcode after end of chain: 320 0x0000007f + Unexpected idcode after end of chain: 352 0x0000007f + Unexpected idcode after end of chain: 384 0x0000007f + Unexpected idcode after end of chain: 480 0x0000007f + Unexpected idcode after end of chain: 512 0x0000007f + Unexpected idcode after end of chain: 544 0x0000007f + double-check your JTAG setup (interface, speed, missing TAPs, ...) + error: -100 + Command handler execution failed + in procedure 'reset' called at file "command.c", line 638 + called at file "/home/laurentiu/workspace/zy1000/build/../openocd/src/helper/command.c", line 352 + > + +	FAIL
SPD004	LPC2148	ZY1000	2MHz on normal operation	Reset init the target according to RES002	Change speed and exercise a memory access over the JTAG, for example `mdw 0x0 32`	The command should run without any errors. If any JTAG checking errors happen, the test failed	+ + > jtag_khz 2000 + jtag_speed 32 => JTAG clk=2.000000 + 2000 kHz + > reset halt + JTAG tap: lpc2148.cpu tap/device found: 0x4f1f0f0f (mfg: 0x787, part: 0xf1f0, ver: 0x4) + srst pulls trst - can not reset into halted mode. Issuing halt after reset. + target state: halted + target halted in Thumb state due to debug-request, current mode: Supervisor + cpsr: 0xa00000f3 pc: 0x7fffd2da + > mdw 0 32 + 0x00000000: e59f4034 e3a05002 e5845000 e3a05003 e5845004 e59f201c e3a03000 e1020093 + 0x00000020: e2822028 e1021093 e3c03007 e5023028 e51ff004 7fffd1c4 e002c014 e01fc000 + 0x00000040: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff + 0x00000060: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff + > + +	PASS
SPD005	LPC2148	ZY1000	RCLK on normal operation	Reset init the target according to RES002	Change speed and exercise a memory access over the JTAG, for example `mdw 0x0 32`	The command should run without any errors. If any JTAG checking errors happen, the test failed	+ `+ > jtag_khz 0 + RCLK - adaptive + > mdw 0 32 + 0x00000000: e59f4034 e3a05002 e5845000 e3a05003 e5845004 e59f201c e3a03000 e1020093 + 0x00000020: e2822028 e1021093 e3c03007 e5023028 e51ff004 7fffd1c4 e002c014 e01fc000 + 0x00000040: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff + 0x00000060: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff + > +` +	PASS

+ +

Debugging

+ + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + +

ID	Target	Interface	Description	Initial state	Input	Expected output	Actual output	Pass/Fail
DBG001	LPC2148	ZY1000	Load is working	Reset init is working, RAM is accesible, GDB server is started	On the console of the OS: + `arm-elf-gdb test_ram.elf` + `(gdb) target remote ip:port` + `(gdb) load +`	Load should return without error, typical output looks like: + `+ Loading section .text, size 0x14c lma 0x0 + Start address 0x40, load size 332 + Transfer rate: 180 bytes/sec, 332 bytes/write. +` +	`+ (gdb) load + Loading section .text, size 0x16c lma 0x40000000 + Start address 0x40000040, load size 364 + Transfer rate: 32 KB/sec, 364 bytes/write. + (gdb) +`	PASS
DBG002	LPC2148	ZY1000	Software breakpoint	Load the test_ram.elf application, use instructions from GDB001	In the GDB console: + `+ (gdb) monitor gdb_breakpoint_override soft + software breakpoints enabled + (gdb) break main + Breakpoint 1 at 0xec: file src/main.c, line 71. + (gdb) continue + Continuing. +` +	The software breakpoint should be reached, a typical output looks like: + `+ target state: halted + target halted in ARM state due to breakpoint, current mode: Supervisor + cpsr: 0x000000d3 pc: 0x000000ec + + Breakpoint 1, main () at src/main.c:71 + 71 DWORD a = 1; +` +	+ `+ (gdb) monitor gdb_breakpoint_override soft + force soft breakpoints + Current language: auto + The current source language is "auto; currently asm". + (gdb) break main + Breakpoint 1 at 0x4000010c: file src/main.c, line 71. + (gdb) c + Continuing. + + Breakpoint 1, main () at src/main.c:71 + 71 DWORD a = 1; + Current language: auto + The current source language is "auto; currently c". + (gdb) +` +	PASS
DBG003	LPC2148	ZY1000	Single step in a RAM application	Load the test_ram.elf application, use instructions from GDB001, break in main using the instructions from GDB002	In GDB, type `(gdb) step`	The next instruction should be reached, typical output: + `+ (gdb) step + target state: halted + target halted in ARM state due to single step, current mode: Abort + cpsr: 0x20000097 pc: 0x000000f0 + target state: halted + target halted in ARM state due to single step, current mode: Abort + cpsr: 0x20000097 pc: 0x000000f4 + 72 DWORD b = 2; +` +	+ `+ (gdb) step + 72 DWORD b = 2; + (gdb) +` +	PASS
DBG004	LPC2148	ZY1000	Software break points are working after a reset	Load the test_ram.elf application, use instructions from GDB001, break in main using the instructions from GDB002	In GDB, type `+ (gdb) monitor reset init + (gdb) load + (gdb) continue +`	The breakpoint should be reached, typical output: + `+ target state: halted + target halted in ARM state due to breakpoint, current mode: Supervisor + cpsr: 0x000000d3 pc: 0x000000ec + + Breakpoint 1, main () at src/main.c:71 + 71 DWORD a = 1; +` +	+ (gdb) moni reset init + JTAG tap: lpc2148.cpu tap/device found: 0x4f1f0f0f (mfg: 0x787, part: 0xf1f0, ver: 0x4) + srst pulls trst - can not reset into halted mode. Issuing halt after reset. + target state: halted + target halted in Thumb state due to debug-request, current mode: Supervisor + cpsr: 0xa00000f3 pc: 0x7fffd2d6 + core state: ARM + (gdb) load + Loading section .text, size 0x16c lma 0x40000000 + Start address 0x40000040, load size 364 + Transfer rate: 27 KB/sec, 364 bytes/write. + (gdb) c + Continuing. + + Breakpoint 1, main () at src/main.c:71 + 71 DWORD a = 1; + (gdb) +	PASS
DBG005	LPC2148	ZY1000	Hardware breakpoint	Flash the test_rom.elf application. Make this test after FLA004 has passed	Be sure that `gdb_memory_map` and `gdb_flash_program` are enabled. In GDB, type + `+ (gdb) monitor reset init + (gdb) load + Loading section .text, size 0x194 lma 0x100000 + Start address 0x100040, load size 404 + Transfer rate: 179 bytes/sec, 404 bytes/write. + (gdb) monitor gdb_breakpoint_override hard + force hard breakpoints + (gdb) break main + Breakpoint 1 at 0x100134: file src/main.c, line 69. + (gdb) continue +` +	The breakpoint should be reached, typical output: + `+ Continuing. + + Breakpoint 1, main () at src/main.c:69 + 69 DWORD a = 1; +` +	+ `+ (gdb) monitor gdb_breakpoint_override hard + force hard breakpoints + (gdb) break main + Breakpoint 1 at 0x10c: file src/main.c, line 71. + (gdb) continue + Continuing. + Note: automatically using hardware breakpoints for read-only addresses. + + Breakpoint 1, main () at src/main.c:71 + 71 DWORD a = 1; + Current language: auto + The current source language is "auto; currently c". + (gdb) +` +	PASS NOTE: This test is failing from time to time, not able to describe a cause
DBG006	LPC2148	ZY1000	Hardware breakpoint is set after a reset	Follow the instructions to flash and insert a hardware breakpoint from DBG005	In GDB, type + `+ (gdb) monitor reset + (gdb) monitor reg pc 0x100000 + pc (/32): 0x00100000 + (gdb) continue +` + where the value inserted in PC is the start address of the application +	The breakpoint should be reached, typical output: + `+ Continuing. + + Breakpoint 1, main () at src/main.c:69 + 69 DWORD a = 1; +` +	+ `+ (gdb) monitor reset init + JTAG tap: lpc2148.cpu tap/device found: 0x4f1f0f0f (mfg: 0x787, part: 0xf1f0, ver: 0x4) + srst pulls trst - can not reset into halted mode. Issuing halt after reset. + target state: halted + target halted in ARM state due to debug-request, current mode: Supervisor + cpsr: 0x60000013 pc: 0x00000160 + core state: ARM + (gdb) monitor reg pc 0x40 + pc (/32): 0x00000040 + (gdb) continue + Continuing. + + Breakpoint 1, main () at src/main.c:71 + 71 DWORD a = 1; + (gdb) +` +	PASS
DBG007	LPC2148	ZY1000	Single step in ROM	Flash the test_rom.elf application and set a breakpoint in main, use DBG005. Make this test after FLA004 has passed	Be sure that `gdb_memory_map` and `gdb_flash_program` are enabled. In GDB, type + `+ (gdb) monitor reset + (gdb) load + Loading section .text, size 0x194 lma 0x100000 + Start address 0x100040, load size 404 + Transfer rate: 179 bytes/sec, 404 bytes/write. + (gdb) monitor gdb_breakpoint_override hard + force hard breakpoints + (gdb) break main + Breakpoint 1 at 0x100134: file src/main.c, line 69. + (gdb) continue + Continuing. + + Breakpoint 1, main () at src/main.c:69 + 69 DWORD a = 1; + (gdb) step +` +	The breakpoint should be reached, typical output: + `+ target state: halted + target halted in ARM state due to single step, current mode: Supervisor + cpsr: 0x60000013 pc: 0x0010013c + 70 DWORD b = 2; +` +	+ (gdb) load + Loading section .text, size 0x16c lma 0x0 + Start address 0x40, load size 364 + Transfer rate: 637 bytes/sec, 364 bytes/write. + (gdb) monitor gdb_breakpoint_override hard + force hard breakpoints + Current language: auto + The current source language is "auto; currently asm". + (gdb) break main + Breakpoint 1 at 0x10c: file src/main.c, line 71. + (gdb) continue + Continuing. + Note: automatically using hardware breakpoints for read-only addresses. + + Breakpoint 1, main () at src/main.c:71 + 71 DWORD a = 1; + Current language: auto + The current source language is "auto; currently c". + (gdb) step + 72 DWORD b = 2; + (gdb) + +	PASS

+ +

RAM access

+Note: these tests are not designed to test/debug the target, but to test functionalities! + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + +

ID	Target	Interface	Description	Initial state	Input	Expected output	Actual output	Pass/Fail
RAM001	LPC2148	ZY1000	32 bit Write/read RAM	Reset init is working	On the telnet interface + `> mww ram_address 0xdeadbeef 16 + > mdw ram_address 32 +` +	The commands should execute without error. A clear failure is a memory access exception. The result of running the commands should be a list of 16 locations 32bit long containing 0xdeadbeef. + `+ > mww 0x0 0xdeadbeef 16 + > mdw 0x0 32 + 0x00000000: deadbeef deadbeef deadbeef deadbeef deadbeef deadbeef deadbeef deadbeef + 0x00000020: deadbeef deadbeef deadbeef deadbeef deadbeef deadbeef deadbeef deadbeef + 0x00000040: e1a00000 e59fa51c e59f051c e04aa000 00080017 00009388 00009388 00009388 + 0x00000060: 00009388 0002c2c0 0002c2c0 000094f8 000094f4 00009388 00009388 00009388 +` +	`+ > mww 0x40000000 0xdeadbeef 16 + > mdw 0x40000000 32 + 0x40000000: deadbeef deadbeef deadbeef deadbeef deadbeef deadbeef deadbeef deadbeef + 0x40000020: deadbeef deadbeef deadbeef deadbeef deadbeef deadbeef deadbeef deadbeef + 0x40000040: e1a00000 e1a00000 e1a00000 e1a00000 e1a00000 e1a00000 e1a00000 e1a00000 + 0x40000060: e321f0db e59fd07c e321f0d7 e59fd078 e321f0d1 e59fd074 e321f0d2 e59fd070 + > +`	PASS
RAM002	LPC2148	ZY1000	16 bit Write/read RAM	Reset init is working	On the telnet interface + `> mwh ram_address 0xbeef 16 + > mdh ram_address 32 +` +	The commands should execute without error. A clear failure is a memory access exception. The result of running the commands should be a list of 16 locations 16bit long containing 0xbeef. + `+ > mwh 0x0 0xbeef 16 + > mdh 0x0 32 + 0x00000000: beef beef beef beef beef beef beef beef beef beef beef beef beef beef beef beef + 0x00000020: 00e0 0000 021c 0000 0240 0000 026c 0000 0288 0000 0000 0000 0388 0000 0350 0000 + > +` +	`+ > mwh 0x40000000 0xbeef 16 + > mdh 0x40000000 32 + 0x40000000: beef beef beef beef beef beef beef beef beef beef beef beef beef beef beef beef + 0x40000020: beef dead beef dead beef dead beef dead beef dead beef dead beef dead beef dead + > +`	PASS
RAM003	LPC2148	ZY1000	8 bit Write/read RAM	Reset init is working	On the telnet interface + `> mwb ram_address 0xab 16 + > mdb ram_address 32 +` +	The commands should execute without error. A clear failure is a memory access exception. The result of running the commands should be a list of 16 locations 8bit long containing 0xab. + `+ > mwb ram_address 0xab 16 + > mdb ram_address 32 + 0x00000000: ab ab ab ab ab ab ab ab ab ab ab ab ab ab ab ab 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 + > +` +	`+ > mwb 0x40000000 0xab 16 + > mdb 0x40000000 32 + 0x40000000: ab ab ab ab ab ab ab ab ab ab ab ab ab ab ab ab ef be ef be ef be ef be ef be ef be ef be ef be + > + +`	PASS

+ + + +

Flash access

+ + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + +

ID	Target	Interface	Description	Initial state	Input	Expected output	Actual output	Pass/Fail
FLA001	LPC2148	ZY1000	Flash probe	Reset init is working	On the telnet interface: + `> flash probe 0` +	The command should execute without error. The output should state the name of the flash and the starting address. An example of output: + `flash 'ecosflash' found at 0x01000000` +	+ `+ > flash probe 0 + flash 'lpc2000' found at 0x00000000 +` +	PASS
FLA002	LPC2148	ZY1000	flash fillw	Reset init is working, flash is probed	On the telnet interface + `> flash fillw 0x1000000 0xdeadbeef 16 +` +	The commands should execute without error. The output looks like: + `+ wrote 64 bytes to 0x01000000 in 11.610000s (0.091516 kb/s) +` + To verify the contents of the flash: + `+ > mdw 0x1000000 32 + 0x01000000: deadbeef deadbeef deadbeef deadbeef deadbeef deadbeef deadbeef deadbeef + 0x01000020: deadbeef deadbeef deadbeef deadbeef deadbeef deadbeef deadbeef deadbeef + 0x01000040: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff + 0x01000060: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff +` +	+ > flash fillw 0x0 0xdeadbeef 16 + Verification will fail since checksum in image (0xdeadbeef) to be written to flash is different from calculated vector checksum (0xe93fc777). + To remove this warning modify build tools on developer PC to inject correct LPC vector checksum. + wrote 64 bytes to 0x00000000 in 0.040000s (1.563 kb/s) + > mdw 0 32 + 0x00000000: deadbeef deadbeef deadbeef deadbeef deadbeef e93fc777 deadbeef deadbeef + 0x00000020: deadbeef deadbeef deadbeef deadbeef deadbeef deadbeef deadbeef deadbeef + 0x00000040: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff + 0x00000060: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff + > +	FAIL
FLA003	LPC2148	ZY1000	Flash erase	Reset init is working, flash is probed	On the telnet interface + `> flash erase_address 0x1000000 0x2000 +` +	The commands should execute without error. + `+ erased address 0x01000000 length 8192 in 4.970000s +` + To check that the flash has been erased, read at different addresses. The result should always be 0xff. + `+ > mdw 0x1000000 32 + 0x01000000: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff + 0x01000020: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff + 0x01000040: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff + 0x01000060: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff +` +	`+ > flash erase_address 0 0x2000 + erased address 0x00000000 (length 8192) in 0.510000s (15.686 kb/s) + > mdw 0 32 + 0x00000000: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff + 0x00000020: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff + 0x00000040: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff + 0x00000060: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff + > +`	PASS
FLA004	LPC2148	ZY1000	Loading to flash from GDB	Reset init is working, flash is probed, connectivity to GDB server is working	Start GDB using a ROM elf image, eg: arm-elf-gdb test_rom.elf. + `+ (gdb) target remote ip:port + (gdb) monitor reset + (gdb) load + Loading section .text, size 0x194 lma 0x100000 + Start address 0x100040, load size 404 + Transfer rate: 179 bytes/sec, 404 bytes/write. + (gdb) monitor verify_image path_to_elf_file +` +	The output should look like: + `+ verified 404 bytes in 5.060000s +` + The failure message is something like: + `Verify operation failed address 0x00200000. Was 0x00 instead of 0x18` +	+ `+ (gdb) moni verify_image /tftp/10.0.0.194/test_rom.elf + checksum mismatch - attempting binary compare + Verify operation failed address 0x00000014. Was 0x58 instead of 0x60 + + Command handler execution failed + in procedure 'verify_image' called at file "command.c", line 647 + called at file "command.c", line 361 + (gdb) +` +	FAIL

+ + + \ No newline at end of file diff --git a/testing/results/v0.4.0-rc1/SAM7.html b/testing/results/v0.4.0-rc1/SAM7.html new file mode 100755 index 00000000..a400a476 --- /dev/null +++ b/testing/results/v0.4.0-rc1/SAM7.html @@ -0,0 +1,853 @@ + + +Test results for revision 1.62 + + + + +

SAM7

+ +

Connectivity

+ + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + +

ID	Target	Interface	Description	Initial state	Input	Expected output	Actual output	Pass/Fail
CON001	SAM7S64	ZY1000	Telnet connection	Power on, jtag target attached	On console, type `telnet ip port`	`Open On-Chip Debugger >`	`Open On-Chip Debugger >`	PASS
CON002	SAM7S64	ZY1000	GDB server connection	Power on, jtag target attached	On GDB console, type `target remote ip:port`	`Remote debugging using 10.0.0.73:3333`	`+ (gdb) tar remo 10.0.0.73:3333 + Remote debugging using 10.0.0.73:3333 + 0x00100174 in ?? () +`	PASS

+ +

Reset

+ + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + +

ID	Target	Interface	Description	Initial state	Input	Expected output	Actual output	Pass/Fail
RES001	SAM7S64	ZY1000	Reset halt on a blank target	Erase all the content of the flash	Connect via the telnet interface and type `reset halt`	Reset should return without error and the output should contain `target state: halted`	+ + > mdw 0 32 + 0x00000000: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff + 0x00000020: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff + 0x00000040: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff + 0x00000060: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff + > reset halt + SRST took 2ms to deassert + JTAG device found: 0x3f0f0f0f (Manufacturer: 0x787, Part: 0xf0f0, Version: 0x3) + srst pulls trst - can not reset into halted mode. Issuing halt after reset. + target state: halted + target halted in ARM state due to debug request, current mode: Supervisor + cpsr: 0x600000d3 pc: 0x000003c4 + > + +	PASS
RES002	SAM7S64	ZY1000	Reset init on a blank target	Erase all the content of the flash	Connect via the telnet interface and type `reset init`	Reset should return without error and the output should contain `executing reset script 'name_of_the_script'`	+ `+ > reset init + SRST took 2ms to deassert + JTAG device found: 0x3f0f0f0f (Manufacturer: 0x787, Part: 0xf0f0, Version: 0x3) + srst pulls trst - can not reset into halted mode. Issuing halt after reset. + target state: halted + target halted in ARM state due to debug request, current mode: Supervisor + cpsr: 0x600000d3 pc: 0x000003c0 + > +` +	PASS + NOTE! Even if there is no message, the reset script is being executed (proved by side effects)
RES003	SAM7S64	ZY1000	Reset after a power cycle of the target	Reset the target then power cycle the target	Connect via the telnet interface and type `reset halt` after the power was detected	Reset should return without error and the output should contain `target state: halted`	+ + Sensed nSRST asserted + Sensed power dropout. + target state: halted + target halted in ARM state due to debug request, current mode: Supervisor + cpsr: 0xf00000d3 pc: 0xd5dff7e6 + Sensed power restore. + Sensed nSRST deasserted + > reset halt + JTAG device found: 0x3f0f0f0f (Manufacturer: 0x787, Part: 0xf0f0, Version: 0x3) + srst pulls trst - can not reset into halted mode. Issuing halt after reset. + target state: halted + target halted in ARM state due to debug request, current mode: Supervisor + cpsr: 0xf00000d3 pc: 0x0000072c + > + +	PASS
RES004	SAM7S64	ZY1000	Reset halt on a blank target where reset halt is supported	Erase all the content of the flash	Connect via the telnet interface and type `reset halt`	Reset should return without error and the output should contain `target state: halted pc = 0`	+ `+ > reset halt + SRST took 2ms to deassert + JTAG device found: 0x3f0f0f0f (Manufacturer: 0x787, Part: 0xf0f0, Version: 0x3) + srst pulls trst - can not reset into halted mode. Issuing halt after reset. + target state: halted + target halted in ARM state due to debug request, current mode: Supervisor + cpsr: 0x300000d3 pc: 0x000003c0 +` +	PASS
RES005	SAM7S64	ZY1000	Reset halt on a blank target using return clock	Erase all the content of the flash, set the configuration script to use RCLK	Connect via the telnet interface and type `reset halt`	Reset should return without error and the output should contain `target state: halted`	+ `+ > jtag_khz 0 + jtag_khz: 0 + > reset init + SRST took 2ms to deassert + JTAG device found: 0x3f0f0f0f (Manufacturer: 0x787, Part: 0xf0f0, Version: 0x3) + srst pulls trst - can not reset into halted mode. Issuing halt after reset. + target state: halted + target halted in ARM state due to debug request, current mode: Supervisor + cpsr: 0x300000d3 pc: 0x000003c0 + executing event/sam7s256_reset.script + > +` +	PASS

+ +

JTAG Speed

+ + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + +

ID	Target	ZY1000	Description	Initial state	Input	Expected output	Actual output	Pass/Fail
SPD001	SAM7S64	ZY1000	16MHz on normal operation	Reset init the target according to RES002	Change speed and exercise a memory access over the JTAG, for example `mdw 0x0 32`	The command should run without any errors. If any JTAG checking errors happen, the test failed	+ `+ > jtag_khz 16000 + jtag_speed 4 => JTAG clk=16.000000 + jtag_khz: 16000 + > mdw 0 32 + 0x00000000: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff + 0x00000020: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff + 0x00000040: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff + 0x00000060: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff + > +` +	PASS
SPD002	SAM7S64	ZY1000	8MHz on normal operation	Reset init the target according to RES002	Change speed and exercise a memory access over the JTAG, for example `mdw 0x0 32`	The command should run without any errors. If any JTAG checking errors happen, the test failed	+ `+ > jtag_khz 8000 + jtag_speed 8 => JTAG clk=8.000000 + jtag_khz: 8000 + > mdw 0 32 + 0x00000000: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff + 0x00000020: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff + 0x00000040: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff + 0x00000060: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff +` +	PASS
SPD003	SAM7S64	ZY1000	4MHz on normal operation	Reset init the target according to RES002	Change speed and exercise a memory access over the JTAG, for example `mdw 0x0 32`	The command should run without any errors. If any JTAG checking errors happen, the test failed	+ `+ > jtag_khz 4000 + jtag_speed 16 => JTAG clk=4.000000 + jtag_khz: 4000 + > mdw 0 32 + 0x00000000: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff + 0x00000020: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff + 0x00000040: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff + 0x00000060: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff + > +` +	PASS
SPD004	SAM7S64	ZY1000	2MHz on normal operation	Reset init the target according to RES002	Change speed and exercise a memory access over the JTAG, for example `mdw 0x0 32`	The command should run without any errors. If any JTAG checking errors happen, the test failed	+ `+ > jtag_khz 2000 + jtag_speed 32 => JTAG clk=2.000000 + jtag_khz: 2000 + > mdw 0 32 + 0x00000000: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff + 0x00000020: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff + 0x00000040: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff + 0x00000060: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff + > +` +	PASS
SPD005	SAM7S64	ZY1000	RCLK on normal operation	Reset init the target according to RES002	Change speed and exercise a memory access over the JTAG, for example `mdw 0x0 32`	The command should run without any errors. If any JTAG checking errors happen, the test failed	+ `+ > jtag_khz 0 + jtag_khz: 0 + > mdw 0 32 + 0x00000000: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff + 0x00000020: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff + 0x00000040: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff + 0x00000060: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff + > +` +	PASS

+ +

Debugging

+ + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + +

ID	Target	Interface	Description	Initial state	Input	Expected output	Actual output	Pass/Fail
DBG001	SAM7S64	ZY1000	Load is working	Reset init is working, RAM is accesible, GDB server is started	On the console of the OS: + `arm-elf-gdb test_ram.elf` + `(gdb) target remote ip:port` + `(gdb) load +`	Load should return without error, typical output looks like: + `+ Loading section .text, size 0x14c lma 0x0 + Start address 0x40, load size 332 + Transfer rate: 180 bytes/sec, 332 bytes/write. +` +	`+ (gdb) load + Loading section .text, size 0x194 lma 0x200000 + Start address 0x200040, load size 404 + Transfer rate: 443 bytes/sec, 404 bytes/write. + (gdb) +`	PASS
DBG002	SAM7S64	ZY1000	Software breakpoint	Load the test_ram.elf application, use instructions from GDB001	In the GDB console: + `+ (gdb) monitor arm7_9 dbgrq enable + software breakpoints enabled + (gdb) break main + Breakpoint 1 at 0xec: file src/main.c, line 71. + (gdb) continue + Continuing. +` +	The software breakpoint should be reached, a typical output looks like: + `+ Breakpoint 1, main () at src/main.c:69 + 69 DWORD a = 1; +` +	+ `+ (gdb) monitor arm7_9 dbgrq enable + use of EmbeddedICE dbgrq instead of breakpoint for target halt enabled + (gdb) break main + Breakpoint 1 at 0x200134: file src/main.c, line 69. + (gdb) c + Continuing. + + Breakpoint 1, main () at src/main.c:69 + 69 DWORD a = 1; + Current language: auto + The current source language is "auto; currently c". + (gdb) +` +	PASS
DBG003	SAM7S64	ZY1000	Single step in a RAM application	Load the test_ram.elf application, use instructions from GDB001, break in main using the instructions from GDB002	In GDB, type `(gdb) step`	The next instruction should be reached, typical output: + `+ (gdb) step + 70 DWORD b = 2; + +` +	+ `+ (gdb) step + 70 DWORD b = 2; + (gdb) +` +	PASS
DBG004	SAM7S64	ZY1000	Software break points are working after a reset	Load the test_ram.elf application, use instructions from GDB001, break in main using the instructions from GDB002	In GDB, type `+ (gdb) monitor reset init + (gdb) load + (gdb) continue +`	The breakpoint should be reached, typical output: + `+ Breakpoint 1, main () at src/main.c:69 + 69 DWORD a = 1; +` +	+ (gdb) monitor reset init + JTAG tap: sam7x256.cpu tap/device found: 0x3f0f0f0f (mfg: 0x787, part: 0xf0f0, ver: 0x3) + srst pulls trst - can not reset into halted mode. Issuing halt after reset. + target state: halted + target halted in ARM state due to debug-request, current mode: Supervisor + cpsr: 0x600000d3 pc: 0x0000031c + (gdb) load + Loading section .text, size 0x194 lma 0x200000 + Start address 0x200040, load size 404 + Transfer rate: 26 KB/sec, 404 bytes/write. + (gdb) continue + Continuing. + + Breakpoint 1, main () at src/main.c:69 + 69 DWORD a = 1; + (gdb) +	PASS
DBG005	SAM7S64	ZY1000	Hardware breakpoint	Flash the test_rom.elf application. Make this test after FLA004 has passed	Be sure that `gdb_memory_map` and `gdb_flash_program` are enabled. In GDB, type + `+ (gdb) monitor reset init + (gdb) load + Loading section .text, size 0x194 lma 0x100000 + Start address 0x100040, load size 404 + Transfer rate: 179 bytes/sec, 404 bytes/write. + (gdb) monitor arm7_9 force_hw_bkpts enable + force hardware breakpoints enabled + (gdb) break main + Breakpoint 1 at 0x100134: file src/main.c, line 69. + (gdb) continue +` +	The breakpoint should be reached, typical output: + `+ Continuing. + + Breakpoint 1, main () at src/main.c:69 + 69 DWORD a = 1; +` +	+ `+ (gdb) monitor arm7_9 force_hw_bkpts enable + force hardware breakpoints enabled + (gdb) break main + Breakpoint 1 at 0x100134: file src/main.c, line 69. + (gdb) continue + Continuing. + Note: automatically using hardware breakpoints for read-only addresses. + target state: halted + target halted in ARM state due to breakpoint, current mode: Supervisor + cpsr: 0x60000013 pc: 0x00100134 + + Breakpoint 1, main () at src/main.c:69 + 69 DWORD a = 1; + (gdb) +` +	PASS
DBG006	SAM7S64	ZY1000	Hardware breakpoint is set after a reset	Follow the instructions to flash and insert a hardware breakpoint from DBG005	In GDB, type + `+ (gdb) monitor reset + (gdb) monitor reg pc 0x100000 + pc (/32): 0x00100000 + (gdb) continue +` + where the value inserted in PC is the start address of the application +	The breakpoint should be reached, typical output: + `+ Continuing. + + Breakpoint 1, main () at src/main.c:69 + 69 DWORD a = 1; +` +	+ + (gdb) monitor reset init + SRST took 3ms to deassert + JTAG device found: 0x3f0f0f0f (Manufacturer: 0x787, Part: 0xf0f0, Version: 0x3) + srst pulls trst - can not reset into halted mode. Issuing halt after reset. + target state: halted + target halted in ARM state due to debug request, current mode: Supervisor + cpsr: 0x60000013 pc: 0x00100168 + executing event/sam7s256_reset.script + (gdb) monitor reg pc 0x100000 + pc (/32): 0x00100000 + (gdb) continue + Continuing. + target state: halted + target halted in ARM state due to single step, current mode: Supervisor + cpsr: 0x60000013 pc: 0x00100040 + target state: halted + target halted in ARM state due to breakpoint, current mode: Supervisor + cpsr: 0x60000013 pc: 0x00100134 + + Breakpoint 1, main () at src/main.c:69 + 69 DWORD a = 1; + (gdb) + +	PASS
DBG007	SAM7S64	ZY1000	Single step in ROM	Flash the test_rom.elf application and set a breakpoint in main, use DBG005. Make this test after FLA004 has passed	Be sure that `gdb_memory_map` and `gdb_flash_program` are enabled. In GDB, type + `+ (gdb) monitor reset + (gdb) load + Loading section .text, size 0x194 lma 0x100000 + Start address 0x100040, load size 404 + Transfer rate: 179 bytes/sec, 404 bytes/write. + (gdb) monitor arm7_9 force_hw_bkpts enable + force hardware breakpoints enabled + (gdb) break main + Breakpoint 1 at 0x100134: file src/main.c, line 69. + (gdb) continue + Continuing. + + Breakpoint 1, main () at src/main.c:69 + 69 DWORD a = 1; + (gdb) step +` +	The breakpoint should be reached, typical output: + `+ target state: halted + target halted in ARM state due to single step, current mode: Supervisor + cpsr: 0x60000013 pc: 0x0010013c + 70 DWORD b = 2; +` +	`+ Breakpoint 1, main () at src/main.c:69 + 69 DWORD a = 1; + (gdb) step + target state: halted + target halted in ARM state due to single step, current mode: Supervisor + cpsr: 0x60000013 pc: 0x00100138 + target state: halted + target halted in ARM state due to single step, current mode: Supervisor + cpsr: 0x60000013 pc: 0x0010013c + 70 DWORD b = 2; + (gdb) +`	PASS

+ +

RAM access

+Note: these tests are not designed to test/debug the target, but to test functionalities! + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + +

ID	Target	Interface	Description	Initial state	Input	Expected output	Actual output	Pass/Fail
RAM001	SAM7S64	ZY1000	32 bit Write/read RAM	Reset init is working	On the telnet interface + `> mww ram_address 0xdeadbeef 16 + > mdw ram_address 32 +` +	The commands should execute without error. A clear failure is a memory access exception. The result of running the commands should be a list of 16 locations 32bit long containing 0xdeadbeef. + `+ > mww 0x0 0xdeadbeef 16 + > mdw 0x0 32 + 0x00000000: deadbeef deadbeef deadbeef deadbeef deadbeef deadbeef deadbeef deadbeef + 0x00000020: deadbeef deadbeef deadbeef deadbeef deadbeef deadbeef deadbeef deadbeef + 0x00000040: e1a00000 e59fa51c e59f051c e04aa000 00080017 00009388 00009388 00009388 + 0x00000060: 00009388 0002c2c0 0002c2c0 000094f8 000094f4 00009388 00009388 00009388 +` +	`+ > mww 0x00200000 0xdeadbeef 16 + > mdw 0x00200000 32 + 0x00200000: deadbeef deadbeef deadbeef deadbeef deadbeef deadbeef deadbeef deadbeef + 0x00200020: deadbeef deadbeef deadbeef deadbeef deadbeef deadbeef deadbeef deadbeef + 0x00200040: e59f10b4 e3a00902 e5810004 e59f00ac e59f10ac e5810000 e3e010ff e59f00a4 + 0x00200060: e5810060 e59f10a0 e3e00000 e5810130 e5810124 e321f0db e59fd090 e321f0d7 +`	PASS
RAM002	SAM7S64	ZY1000	16 bit Write/read RAM	Reset init is working	On the telnet interface + `> mwh ram_address 0xbeef 16 + > mdh ram_address 32 +` +	The commands should execute without error. A clear failure is a memory access exception. The result of running the commands should be a list of 16 locations 16bit long containing 0xbeef. + `+ > mwh 0x0 0xbeef 16 + > mdh 0x0 32 + 0x00000000: beef beef beef beef beef beef beef beef beef beef beef beef beef beef beef beef + 0x00000020: 00e0 0000 021c 0000 0240 0000 026c 0000 0288 0000 0000 0000 0388 0000 0350 0000 + > +` +	`+ > mwh 0x00200000 0xbeef 16 + > mdh 0x00200000 32 + 0x00200000: beef beef beef beef beef beef beef beef beef beef beef beef beef beef beef beef + 0x00200020: 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 +`	PASS
RAM003	SAM7S64	ZY1000	8 bit Write/read RAM	Reset init is working	On the telnet interface + `> mwb ram_address 0xab 16 + > mdb ram_address 32 +` +	The commands should execute without error. A clear failure is a memory access exception. The result of running the commands should be a list of 16 locations 8bit long containing 0xab. + `+ > mwb ram_address 0xab 16 + > mdb ram_address 32 + 0x00000000: ab ab ab ab ab ab ab ab ab ab ab ab ab ab ab ab 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 + > +` +	`+ > mwb 0x00200000 0xab 16 + > mdb 0x00200000 32 + 0x00200000: ab ab ab ab ab ab ab ab ab ab ab ab ab ab ab ab 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 +`	PASS

+ + + +

Flash access

+ + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + +

ID	Target	Interface	Description	Initial state	Input	Expected output	Actual output	Pass/Fail
FLA001	SAM7S64	ZY1000	Flash probe	Reset init is working	On the telnet interface: + `> flash probe 0` +	The command should execute without error. The output should state the name of the flash and the starting address. An example of output: + `flash 'ecosflash' found at 0x01000000` +	+ `+ > flash probe 0 + flash 'at91sam7' found at 0x00100000 +` +	PASS
FLA002	SAM7S64	ZY1000	flash fillw	Reset init is working, flash is probed	On the telnet interface + `> flash fillw 0x100000 0xdeadbeef 16 +` +	The commands should execute without error. The output looks like: + `+ wrote 64 bytes to 0x0100000 in 11.610000s (0.091516 kb/s) +` + To verify the contents of the flash: + `+ > mdw 0x100000 32 + 0x0100000: deadbeef deadbeef deadbeef deadbeef deadbeef deadbeef deadbeef deadbeef + 0x0100020: deadbeef deadbeef deadbeef deadbeef deadbeef deadbeef deadbeef deadbeef + 0x0100040: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff + 0x0100060: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff +` +	`+ > flash fillw 0x100000 0xdeadbeef 16 + wrote 64 bytes to 0x00100000 in 0.040000s (26.562500 kb/s) + > mdw 0x100000 32 + 0x00100000: deadbeef deadbeef deadbeef deadbeef deadbeef deadbeef deadbeef deadbeef + 0x00100020: deadbeef deadbeef deadbeef deadbeef deadbeef deadbeef deadbeef deadbeef + 0x00100040: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff + 0x00100060: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff + > +`	PASS
FLA003	SAM7S64	ZY1000	Flash erase	Reset init is working, flash is probed	On the telnet interface + `> flash erase_address 0x100000 0x2000 +` +	The commands should execute without error. + `+ erased address 0x0100000 length 8192 in 4.970000s +` + To check that the flash has been erased, read at different addresses. The result should always be 0xff. + `+ > mdw 0x100000 32 + 0x0100000: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff + 0x0100020: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff + 0x0100040: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff + 0x0100060: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff +` +	`+ > flash erase_address 0x100000 0x2000 + erased address 0x00100000 length 8192 in 0.020000s + > mdw 0x100000 32 + 0x00100000: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff + 0x00100020: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff + 0x00100040: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff + 0x00100060: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff + > +`	PASS
FLA004	SAM7S64	ZY1000	Loading to flash from GDB	Reset init is working, flash is probed, connectivity to GDB server is working	Start GDB using a ROM elf image, eg: arm-elf-gdb test_rom.elf. + `+ (gdb) target remote ip:port + (gdb) monitor reset halt + (gdb) load + Loading section .text, size 0x194 lma 0x100000 + Start address 0x100040, load size 404 + Transfer rate: 179 bytes/sec, 404 bytes/write. + (gdb) monitor verify_image path_to_elf_file +` +	The output should look like: + `+ verified 404 bytes in 5.060000s +` + The failure message is something like: + `Verify operation failed address 0x00200000. Was 0x00 instead of 0x18` +	+ `+ (gdb) load + Loading section .text, size 0x194 lma 0x100000 + Start address 0x100040, load size 404 + Transfer rate: 4 KB/sec, 404 bytes/write. + (gdb) moni verify_image /tftp/10.0.0.9/c:/temp/testing/examples/SAM7S256Test/test_rom.elf + verified 404 bytes in 0.570000s +` +	PASS

+ + + \ No newline at end of file diff --git a/testing/results/v0.4.0-rc1/STR710.html b/testing/results/v0.4.0-rc1/STR710.html new file mode 100755 index 00000000..1a18ad0e --- /dev/null +++ b/testing/results/v0.4.0-rc1/STR710.html @@ -0,0 +1,907 @@ + + +Test results for version 1.62 + + + + +

STR710

+ +

Connectivity

+ + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + +

ID	Target	Interface	Description	Initial state	Input	Expected output	Actual output	Pass/Fail
CON001	STR912	ZY1000	Telnet connection	Power on, jtag target attached	On console, type `telnet ip port`	`Open On-Chip Debugger >`	`> telnet 10.0.0.142 + Trying 10.0.0.142... + Connected to 10.0.0.142. + Escape character is '^]'. + Open On-Chip Debugger + > +`	PASS
CON002	STR912	ZY1000	GDB server connection	Power on, jtag target attached	On GDB console, type `target remote ip:port`	`Remote debugging using 10.0.0.73:3333`	`+ (gdb) tar remo 10.0.0.142:3333 + Remote debugging using 10.0.0.142:3333 + 0x00016434 in ?? () + (gdb) +`	PASS

+ +

Reset

+ + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + +

ID	Target	Interface	Description	Initial state	Input	Expected output	Actual output	Pass/Fail
RES001	STR912	ZY1000	Reset halt on a blank target	Erase all the content of the flash	Connect via the telnet interface and type `reset halt`	Reset should return without error and the output should contain `target state: halted`	+ `+> mdw 0 32 +0x00000000: 75755000 8a930104 65696f65 939a3e98 214751f1 fa0edb9b 6664686d 931a989e +0x00000020: 676c65e4 9a0a0982 25653445 da02ba90 c4ed3165 9b9a8a9a 65676365 01981292 +0x00000040: 212e0982 82ba3f8b 34674765 96ba1a9a 6175e7e5 9b9ab91a 0789644d 120a9a18 +0x00000060: 65446167 80d20982 6d6d6565 187090ca 65277d65 9a9a0b81 6960416c 9ffe88b8 +> reset +jtag_speed 6400 => JTAG clk=0.010000 +10 kHz +JTAG tap: str710.cpu tap/device found: 0x3f0f0f0f (mfg: 0x787, part: 0xf0f0, ver: 0x3) +> +` +	PASS
RES002	STR912	ZY1000	Reset init on a blank target	Erase all the content of the flash	Connect via the telnet interface and type `reset init`	Reset should return without error and the output should contain `executing reset script 'name_of_the_script'`	+ `+> reset init +jtag_speed 6400 => JTAG clk=0.010000 +10 kHz +JTAG tap: str710.cpu tap/device found: 0x3f0f0f0f (mfg: 0x787, part: 0xf0f0, ver: 0x3) +srst pulls trst - can not reset into halted mode. Issuing halt after reset. +target state: halted +target halted in ARM state due to debug-request, current mode: Undefined instruction +cpsr: 0xf00000db pc: 0x00000004 +jtag_speed 10 => JTAG clk=6.400000 +6400 kHz +` +	PASS
RES003	STR912	ZY1000	Reset after a power cycle of the target	Reset the target then power cycle the target	Connect via the telnet interface and type `reset halt` after the power was detected	Reset should return without error and the output should contain `target state: halted`	+ + nsed power dropout. + nsed power dropout. + nsed nSRST deasserted. + invalid mode value encountered 0 +cpsr contains invalid mode value - communication failure +jtag_speed 6400 => JTAG clk=0.010000 +10 kHz +JTAG tap: str710.cpu tap/device found: 0x3f0f0f0f (mfg: 0x787, part: 0xf0f0, ver: 0x3) +srst pulls trst - can not reset into halted mode. Issuing halt after reset. +target state: halted +target halted in ARM state due to debug-request, current mode: Supervisor +cpsr: 0x100000d3 pc: 0x0000001c +jtag_speed 10 => JTAG clk=6.400000 +6400 kHz + nsed power restore. +jtag_speed 6400 => JTAG clk=0.010000 +10 kHz +JTAG tap: str710.cpu tap/device found: 0x3f0f0f0f (mfg: 0x787, part: 0xf0f0, ver: 0x3) +srst pulls trst - can not reset into halted mode. Issuing halt after reset. +target state: halted +target halted in ARM state due to debug-request, current mode: Supervisor +cpsr: 0x500000d3 pc: 0x00000000 +jtag_speed 10 => JTAG clk=6.400000 +6400 kHz +> reset init +jtag_speed 6400 => JTAG clk=0.010000 +10 kHz +JTAG tap: str710.cpu tap/device found: 0x3f0f0f0f (mfg: 0x787, part: 0xf0f0, ver: 0x3) +srst pulls trst - can not reset into halted mode. Issuing halt after reset. +target state: halted +target halted in ARM state due to debug-request, current mode: Supervisor +cpsr: 0x500000d3 pc: 0x00000000 +jtag_speed 10 => JTAG clk=6.400000 +6400 kHz +> + +	PASS
RES004	STR912	ZY1000	Reset halt on a blank target where reset halt is supported	Erase all the content of the flash	Connect via the telnet interface and type `reset halt`	Reset should return without error and the output should contain `target state: halted`	+ `+> reset halt +jtag_speed 6400 => JTAG clk=0.010000 +10 kHz +JTAG tap: str710.cpu tap/device found: 0x3f0f0f0f (mfg: 0x787, part: 0xf0f0, ver: 0x3) +srst pulls trst - can not reset into halted mode. Issuing halt after reset. +target state: halted +target halted in ARM state due to debug-request, current mode: Supervisor +cpsr: 0x200000d3 pc: 0xfe50cba4 +> +` +	PASS
RES005	STR912	ZY1000	Reset halt on a blank target using return clock	Erase all the content of the flash, set the configuration script to use RCLK	Connect via the telnet interface and type `reset halt`	Reset should return without error and the output should contain `target state: halted`	+ `+ > jtag_khz 0 +RCLK - adaptive +RCLK timeout +RCLK timeout +RCLK timeout + > reset halt + RCLK timeout +jtag_speed 6400 => JTAG clk=0.010000 +10 kHz +JTAG tap: str710.cpu tap/device found: 0x3f0f0f0f (mfg: 0x787, part: 0xf0f0, ver: 0x3) +srst pulls trst - can not reset into halted mode. Issuing halt after reset. +target state: halted +target halted in ARM state due to debug-request, current mode: Supervisor +cpsr: 0x200000d3 pc: 0xfe50cb50 +` +	FAIL

+ +

JTAG Speed

+ + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + +

ID	Target	ZY1000	Description	Initial state	Input	Expected output	Actual output	Pass/Fail
SPD001	STR912	ZY1000	16MHz on normal operation	Reset init the target according to RES002	Change speed and exercise a memory access over the JTAG, for example `mdw 0x0 32`	The command should run without any errors. If any JTAG checking errors happen, the test failed	+ `+> jtag_khz 16000 +jtag_speed 4 => JTAG clk=16.000000 +16000 kHz +> mdw 0 32 +0x00000000: 75755000 8a930104 65696f65 939a3e98 214751f1 fa0edb9b 6664686d 931a989e +0x00000020: 676c65e4 9a0a0982 25653445 da02ba90 c4ed3165 9b9a8a9a 65676365 01981292 +0x00000040: 212e0982 82ba3f8b 34674765 96ba1a9a 6175e7e5 9b9ab91a 0789644d 120a9a18 +0x00000060: 65446167 80d20982 6d6d6565 187090ca 65277d65 9a9a0b81 6960416c 9ffe88b8 +> +` +	PASS
SPD002	STR912	ZY1000	8MHz on normal operation	Reset init the target according to RES002	Change speed and exercise a memory access over the JTAG, for example `mdw 0x0 32`	The command should run without any errors. If any JTAG checking errors happen, the test failed	+ `+> jtag_khz 8000 +jtag_speed 8 => JTAG clk=8.000000 +8000 kHz +> mdw 0 32 +0x00000000: 75755000 8a930104 65696f65 939a3e98 214751f1 fa0edb9b 6664686d 931a989e +0x00000020: 676c65e4 9a0a0982 25653445 da02ba90 c4ed3165 9b9a8a9a 65676365 01981292 +0x00000040: 212e0982 82ba3f8b 34674765 96ba1a9a 6175e7e5 9b9ab91a 0789644d 120a9a18 +0x00000060: 65446167 80d20982 6d6d6565 187090ca 65277d65 9a9a0b81 6960416c 9ffe88b8 +> +` +	PASS
SPD003	STR912	ZY1000	4MHz on normal operation	Reset init the target according to RES002	Change speed and exercise a memory access over the JTAG, for example `mdw 0x0 32`	The command should run without any errors. If any JTAG checking errors happen, the test failed	+ `+> jtag_khz 4000 +jtag_speed 16 => JTAG clk=4.000000 +4000 kHz +> mdw 0 32 +0x00000000: 75755000 8a930104 65696f65 939a3e98 214751f1 fa0edb9b 6664686d 931a989e +0x00000020: 676c65e4 9a0a0982 25653445 da02ba90 c4ed3165 9b9a8a9a 65676365 01981292 +0x00000040: 212e0982 82ba3f8b 34674765 96ba1a9a 6175e7e5 9b9ab91a 0789644d 120a9a18 +0x00000060: 65446167 80d20982 6d6d6565 187090ca 65277d65 9a9a0b81 6960416c 9ffe88b8 +> +` +	PASS
SPD004	STR912	ZY1000	2MHz on normal operation	Reset init the target according to RES002	Change speed and exercise a memory access over the JTAG, for example `mdw 0x0 32`	The command should run without any errors. If any JTAG checking errors happen, the test failed	+ `+> > jtag_khz 2000 +jtag_speed 32 => JTAG clk=2.000000 +2000 kHz +> mdw 0 32 +0x00000000: 75755000 8a930104 65696f65 939a3e98 214751f1 fa0edb9b 6664686d 931a989e +0x00000020: 676c65e4 9a0a0982 25653445 da02ba90 c4ed3165 9b9a8a9a 65676365 01981292 +0x00000040: 212e0982 82ba3f8b 34674765 96ba1a9a 6175e7e5 9b9ab91a 0789644d 120a9a18 +0x00000060: 65446167 80d20982 6d6d6565 187090ca 65277d65 9a9a0b81 6960416c 9ffe88b8 +> +` +	PASS
SPD005	STR912	ZY1000	RCLK on normal operation	Reset init the target according to RES002	Change speed and exercise a memory access over the JTAG, for example `mdw 0x0 32`	The command should run without any errors. If any JTAG checking errors happen, the test failed	+ `+> jtag_khz 0 +RCLK - adaptive +RCLK timeout +RCLK timeout +RCLK timeout +` +	FAIL

+ +

Debugging

+ + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + +

ID	Target	Interface	Description	Initial state	Input	Expected output	Actual output	Pass/Fail
DBG001	STR912	ZY1000	Load is working	Reset init is working, RAM is accesible, GDB server is started	On the console of the OS: + `arm-elf-gdb test_ram.elf` + `(gdb) target remote ip:port` + `(gdb) load +`	Load should return without error, typical output looks like: + `+ Loading section .text, size 0x14c lma 0x0 + Start address 0x40, load size 332 + Transfer rate: 180 bytes/sec, 332 bytes/write. +` +	`+(gdb) load +Loading section .text, size 0x1cc lma 0x20000000 +Loading section .vectors, size 0x40 lma 0x200001cc +Loading section .rodata, size 0x4 lma 0x2000020c +Start address 0x20000000, load size 528 +Transfer rate: 64 KB/sec, 176 bytes/write. +(gdb) +`	PASS
DBG002	STR912	ZY1000	Software breakpoint	Load the test_ram.elf application, use instructions from GDB001	In the GDB console: + `+ (gdb) monitor gdb_breakpoint_override soft + force soft breakpoints + (gdb) break main + Breakpoint 1 at 0xec: file src/main.c, line 71. + (gdb) continue + Continuing. +` +	The software breakpoint should be reached, a typical output looks like: + `+ target state: halted + target halted in ARM state due to breakpoint, current mode: Supervisor + cpsr: 0x000000d3 pc: 0x000000ec + + Breakpoint 1, main () at src/main.c:71 + 71 DWORD a = 1; +` +	+ `+(gdb) monitor gdb_breakpoint_override soft +force soft breakpoints +Current language: auto +The current source language is "auto; currently asm". +(gdb) break main +Breakpoint 1 at 0x20000170: file src/main.c, line 69. +(gdb) c +Continuing. + +Breakpoint 1, main () at src/main.c:69 +69 DWORD a = 1; +Current language: auto +The current source language is "auto; currently c". +(gdb) +` +	PASS
DBG003	STR912	ZY1000	Single step in a RAM application	Load the test_ram.elf application, use instructions from GDB001, break in main using the instructions from GDB002	In GDB, type `(gdb) step`	The next instruction should be reached, typical output: + `+ (gdb) step + target state: halted + target halted in ARM state due to single step, current mode: Abort + cpsr: 0x20000097 pc: 0x000000f0 + target state: halted + target halted in ARM state due to single step, current mode: Abort + cpsr: 0x20000097 pc: 0x000000f4 + 72 DWORD b = 2; +` +	+ `+ (gdb) step + 70 DWORD b = 2; + (gdb) +` +	PASS
DBG004	STR912	ZY1000	Software break points are working after a reset	Load the test_ram.elf application, use instructions from GDB001, break in main using the instructions from GDB002	In GDB, type `+ (gdb) monitor reset init + (gdb) load + (gdb) continue +`	The breakpoint should be reached, typical output: + `+ target state: halted + target halted in ARM state due to breakpoint, current mode: Supervisor + cpsr: 0x000000d3 pc: 0x000000ec + + Breakpoint 1, main () at src/main.c:71 + 71 DWORD a = 1; +` +	+((gdb) monitor reset init +jtag_speed 6400 => JTAG clk=0.010000 +10 kHz +JTAG tap: str710.cpu tap/device found: 0x3f0f0f0f (mfg: 0x787, part: 0xf0f0, ver: 0x3) +srst pulls trst - can not reset into halted mode. Issuing halt after reset. +target state: halted +target halted in ARM state due to debug-request, current mode: Supervisor +cpsr: 0x60000013 pc: 0x200001bc +jtag_speed 10 => JTAG clk=6.400000 +6400 kHz +(gdb) load +Loading section .text, size 0x1cc lma 0x20000000 +Loading section .vectors, size 0x40 lma 0x200001cc +Loading section .rodata, size 0x4 lma 0x2000020c +Start address 0x20000000, load size 528 +Transfer rate: 64 KB/sec, 176 bytes/write. +(gdb) c +Continuing. + +Breakpoint 1, main () at src/main.c:69 +69 DWORD a = 1; +(gdb) +	PASS
DBG005	STR912	ZY1000	Hardware breakpoint	Flash the test_rom.elf application. Make this test after FLA004 has passed	Be sure that `gdb_memory_map` and `gdb_flash_program` are enabled. In GDB, type + `+ (gdb) monitor reset init + (gdb) load + Loading section .text, size 0x194 lma 0x100000 + Start address 0x100040, load size 404 + Transfer rate: 179 bytes/sec, 404 bytes/write. + (gdb) monitor gdb_breakpoint_override hard + force hard breakpoints + (gdb) break main + Breakpoint 1 at 0x100134: file src/main.c, line 69. + (gdb) continue +` +	The breakpoint should be reached, typical output: + `+ Continuing. + + Breakpoint 1, main () at src/main.c:69 + 69 DWORD a = 1; +` +	+ `+(gdb) monitor gdb_breakpoint_override hard +force hard breakpoints +(gdb) break main +Breakpoint 1 at 0x40000170: file src/main.c, line 69. +(gdb) c +Continuing. +Note: automatically using hardware breakpoints for read-only addresses. + +Breakpoint 1, main () at src/main.c:69 +69 DWORD a = 1; +Current language: auto +The current source language is "auto; currently c". +(gdb) +` +	PASS
DBG006	STR912	ZY1000	Hardware breakpoint is set after a reset	Follow the instructions to flash and insert a hardware breakpoint from DBG005	In GDB, type + `+ (gdb) monitor reset + (gdb) monitor reg pc 0x100000 + pc (/32): 0x00100000 + (gdb) continue +` + where the value inserted in PC is the start address of the application +	The breakpoint should be reached, typical output: + `+ Continuing. + + Breakpoint 1, main () at src/main.c:69 + 69 DWORD a = 1; +` +	+ +(gdb) monitor reset init +jtag_speed 6400 => JTAG clk=0.010000 +10 kHz +JTAG tap: str710.cpu tap/device found: 0x3f0f0f0f (mfg: 0x787, part: 0xf0f0, ver: 0x3) +srst pulls trst - can not reset into halted mode. Issuing halt after reset. +target state: halted +target halted in ARM state due to debug-request, current mode: Undefined instruction +cpsr: 0x400000db pc: 0x010aea80 +jtag_speed 10 => JTAG clk=6.400000 +6400 kHz +(gdb) monitor reg pc 0x40000000 +pc (/32): 0x40000000 +(gdb) c +Continuing. + +Breakpoint 1, main () at src/main.c:69 +69 DWORD a = 1; +Current language: auto +The current source language is "auto; currently c". +(gdb) + +	PASS
DBG007	STR912	ZY1000	Single step in ROM	Flash the test_rom.elf application and set a breakpoint in main, use DBG005. Make this test after FLA004 has passed	Be sure that `gdb_memory_map` and `gdb_flash_program` are enabled. In GDB, type + `+ (gdb) monitor reset + (gdb) load + Loading section .text, size 0x194 lma 0x100000 + Start address 0x100040, load size 404 + Transfer rate: 179 bytes/sec, 404 bytes/write. + (gdb) monitor arm7_9 force_hw_bkpts enable + force hardware breakpoints enabled + (gdb) break main + Breakpoint 1 at 0x100134: file src/main.c, line 69. + (gdb) continue + Continuing. + + Breakpoint 1, main () at src/main.c:69 + 69 DWORD a = 1; + (gdb) step +` +	The breakpoint should be reached, typical output: + `+ target state: halted + target halted in ARM state due to single step, current mode: Supervisor + cpsr: 0x60000013 pc: 0x0010013c + 70 DWORD b = 2; +` +	`+Breakpoint 2, main () at src/main.c:69 +69 DWORD a = 1; +Current language: auto +The current source language is "auto; currently c". +(gdb) step +70 DWORD b = 2; +(gdb) +`	PASS

+ +

RAM access

+Note: these tests are not designed to test/debug the target, but to test functionalities! + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + +

ID	Target	Interface	Description	Initial state	Input	Expected output	Actual output	Pass/Fail
RAM001	STR912	ZY1000	32 bit Write/read RAM	Reset init is working	On the telnet interface + `> mww ram_address 0xdeadbeef 16 + > mdw ram_address 32 +` +	The commands should execute without error. A clear failure is a memory access exception. The result of running the commands should be a list of 16 locations 32bit long containing 0xdeadbeef. + `+ > mww 0x0 0xdeadbeef 16 + > mdw 0x0 32 + 0x00000000: deadbeef deadbeef deadbeef deadbeef deadbeef deadbeef deadbeef deadbeef + 0x00000020: deadbeef deadbeef deadbeef deadbeef deadbeef deadbeef deadbeef deadbeef + 0x00000040: e1a00000 e59fa51c e59f051c e04aa000 00080017 00009388 00009388 00009388 + 0x00000060: 00009388 0002c2c0 0002c2c0 000094f8 000094f4 00009388 00009388 00009388 +` +	`+> mww 0x20000000 0xdeadbeef 16 +> mdw 0x20000000 32 +0x20000000: deadbeef deadbeef deadbeef deadbeef deadbeef deadbeef deadbeef deadbeef +0x20000020: deadbeef deadbeef deadbeef deadbeef deadbeef deadbeef deadbeef deadbeef +0x20000040: e3a0020a e3a01073 e5801018 e5901008 e3110002 0afffffc e3a0020a e59f10d0 +0x20000060: e5801008 e321f0db e59fd0c8 e321f0d7 e59fd0c4 e321f0d1 e59fd0c0 e321f0d2 +> +`	PASS
RAM002	STR912	ZY1000	16 bit Write/read RAM	Reset init is working	On the telnet interface + `> mwh ram_address 0xbeef 16 + > mdh ram_address 32 +` +	The commands should execute without error. A clear failure is a memory access exception. The result of running the commands should be a list of 16 locations 16bit long containing 0xbeef. + `+ > mwh 0x0 0xbeef 16 + > mdh 0x0 32 + 0x00000000: beef beef beef beef beef beef beef beef beef beef beef beef beef beef beef beef + 0x00000020: 00e0 0000 021c 0000 0240 0000 026c 0000 0288 0000 0000 0000 0388 0000 0350 0000 + > +` +	`+> mwh 0x20000000 0xbeef 16 +> mdh 0x20000000 32 +0x20000000: beef beef beef beef beef beef beef beef beef beef beef beef beef beef beef beef +0x20000020: beef dead beef dead beef dead beef dead beef dead beef dead beef dead beef dead +> +`	PASS
RAM003	STR912	ZY1000	8 bit Write/read RAM	Reset init is working	On the telnet interface + `> mwb ram_address 0xab 16 + > mdb ram_address 32 +` +	The commands should execute without error. A clear failure is a memory access exception. The result of running the commands should be a list of 16 locations 8bit long containing 0xab. + `+ > mwb ram_address 0xab 16 + > mdb ram_address 32 + 0x00000000: ab ab ab ab ab ab ab ab ab ab ab ab ab ab ab ab 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 + > +` +	`+> mwb 0x20000000 0xab 16 +> mdb 0x20000000 32 +0x20000000: ab ab ab ab ab ab ab ab ab ab ab ab ab ab ab ab ef be ef be ef be ef be ef be ef be ef be ef be +> +`	PASS

+ + + +

Flash access

+ + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + +

ID	Target	Interface	Description	Initial state	Input	Expected output	Actual output	Pass/Fail
FLA001	STR912	ZY1000	Flash probe	Reset init is working	On the telnet interface: + `> flash probe 0` +	The command should execute without error. The output should state the name of the flash and the starting address. An example of output: + `flash 'ecosflash' found at 0x01000000` +	+ `+ > flash probe 0 + flash 'str7x' found at 0x40000000 + > +` +	PASS
FLA002	STR912	ZY1000	flash fillw	Reset init is working, flash is probed	On the telnet interface + `> flash fillw 0x1000000 0xdeadbeef 16 +` +	The commands should execute without error. The output looks like: + `+ wrote 64 bytes to 0x01000000 in 11.610000s (0.091516 kb/s) +` + To verify the contents of the flash: + `+ > mdw 0x1000000 32 + 0x01000000: deadbeef deadbeef deadbeef deadbeef deadbeef deadbeef deadbeef deadbeef + 0x01000020: deadbeef deadbeef deadbeef deadbeef deadbeef deadbeef deadbeef deadbeef + 0x01000040: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff + 0x01000060: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff +` +	`+ > flash fillw 0x40000000 0xdeadbeef 16 + wrote 64 bytes to 0x40000000 in 0.000000s (inf kb/s) + > mdw 0x40000000 32 + 0x40000000: deadbeef deadbeef deadbeef deadbeef deadbeef deadbeef deadbeef deadbeef + 0x40000020: deadbeef deadbeef deadbeef deadbeef deadbeef deadbeef deadbeef deadbeef + 0x40000040: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff + 0x40000060: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff + > +`	PASS
FLA003	STR912	ZY1000	Flash erase	Reset init is working, flash is probed	On the telnet interface + `> flash erase_address 0x1000000 0x2000 +` +	The commands should execute without error. + `+ erased address 0x01000000 length 8192 in 4.970000s +` + To check that the flash has been erased, read at different addresses. The result should always be 0xff. + `+ > mdw 0x1000000 32 + 0x01000000: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff + 0x01000020: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff + 0x01000040: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff + 0x01000060: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff +` +	`+> flash erase_address 0x40000000 0x2000 +erased address 0x40000000 (length 8192) in 0.270000s (29.630 kb/s) +> mdw 0x40000000 32 +0x40000000: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff +0x40000020: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff +0x40000040: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff +0x40000060: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff +> +`	PASS
FLA004	STR912	ZY1000	Loading to flash from GDB	Reset init is working, flash is probed, connectivity to GDB server is working	Start GDB using a ROM elf image, eg: arm-elf-gdb test_rom.elf. + `+ (gdb) target remote ip:port + (gdb) monitor reset + (gdb) load + Loading section .text, size 0x194 lma 0x100000 + Start address 0x100040, load size 404 + Transfer rate: 179 bytes/sec, 404 bytes/write. + (gdb) monitor verify_image path_to_elf_file +` +	The output should look like: + `+ verified 404 bytes in 5.060000s +` + The failure message is something like: + `Verify operation failed address 0x00200000. Was 0x00 instead of 0x18` +	+ `+(gdb) load +Loading section .text, size 0x1cc lma 0x40000000 +Loading section .vectors, size 0x40 lma 0x400001cc +Loading section .rodata, size 0x4 lma 0x4000020c +Start address 0x40000000, load size 528 +Transfer rate: 53 bytes/sec, 176 bytes/write. +(gdb) monitor verify_image /tftp/10.0.0.194/test_rom.elf +verified 528 bytes in 4.760000s (0.108 kb/s) +Current language: auto +The current source language is "auto; currently asm". +(gdb) +` +	PASS

+ + + \ No newline at end of file diff --git a/testing/results/v0.4.0-rc1/STR912.html b/testing/results/v0.4.0-rc1/STR912.html new file mode 100755 index 00000000..c8df0348 --- /dev/null +++ b/testing/results/v0.4.0-rc1/STR912.html @@ -0,0 +1,1008 @@ + + +Test results for version 1.62 + + + + +

STR912

+ +

Connectivity

+ + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + +

ID	Target	Interface	Description	Initial state	Input	Expected output	Actual output	Pass/Fail
CON001	STR912	ZY1000	Telnet connection	Power on, jtag target attached	On console, type `telnet ip port`	`Open On-Chip Debugger >`	`> telnet 10.0.0.142 + Trying 10.0.0.142... + Connected to 10.0.0.142. + Escape character is '^]'. + Open On-Chip Debugger + > +`	PASS
CON002	STR912	ZY1000	GDB server connection	Power on, jtag target attached	On GDB console, type `target remote ip:port`	`Remote debugging using 10.0.0.73:3333`	`+ (gdb) tar remo 10.0.0.142:3333 + Remote debugging using 10.0.0.142:3333 + 0x00016434 in ?? () + (gdb) +`	PASS

+ +

Reset

+ + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + +

ID	Target	Interface	Description	Initial state	Input	Expected output	Actual output	Pass/Fail
RES001	STR912	ZY1000	Reset halt on a blank target	Erase all the content of the flash	Connect via the telnet interface and type `reset halt`	Reset should return without error and the output should contain `target state: halted`	+ +> reset halt +RCLK - adaptive +SRST took 2ms to deassert +JTAG tap: str912.flash tap/device found: 0x04570041 (mfg: 0x020, part: 0x4570, ver: 0x0) +JTAG tap: str912.cpu tap/device found: 0x25966041 (mfg: 0x020, part: 0x5966, ver: 0x2) +JTAG tap: str912.bs tap/device found: 0x2457f041 (mfg: 0x020, part: 0x457f, ver: 0x2) +JTAG tap: str912.bs UNEXPECTED: 0x2457f041 (mfg: 0x020, part: 0x457f, ver: 0x2) +JTAG tap: str912.bs expected 1 of 1: 0x1457f041 (mfg: 0x020, part: 0x457f, ver: 0x1) +Trying to use configured scan chain anyway... +Bypassing JTAG setup events due to errors +SRST took 2ms to deassert +target state: halted +target halted in ARM state due to debug-request, current mode: Supervisor +cpsr: 0x000000d3 pc: 0x00000000 +NOTE! DCC downloads have not been enabled, defaulting to slow memory writes. Type 'help dcc'. +> + +	PASS
RES002	STR912	ZY1000	Reset init on a blank target	Erase all the content of the flash	Connect via the telnet interface and type `reset init`	Reset should return without error and the output should contain `executing reset script 'name_of_the_script'`	+ +> reset init +RCLK - adaptive +SRST took 2ms to deassert +JTAG tap: str912.flash tap/device found: 0x04570041 (mfg: 0x020, part: 0x4570, ver: 0x0) +JTAG tap: str912.cpu tap/device found: 0x25966041 (mfg: 0x020, part: 0x5966, ver: 0x2) +JTAG tap: str912.bs tap/device found: 0x2457f041 (mfg: 0x020, part: 0x457f, ver: 0x2) +JTAG tap: str912.bs UNEXPECTED: 0x2457f041 (mfg: 0x020, part: 0x457f, ver: 0x2) +JTAG tap: str912.bs expected 1 of 1: 0x1457f041 (mfg: 0x020, part: 0x457f, ver: 0x1) +Trying to use configured scan chain anyway... +Bypassing JTAG setup events due to errors +SRST took 2ms to deassert +target state: halted +target halted in ARM state due to debug-request, current mode: Supervisor +cpsr: 0x000000d3 pc: 0x00000000 +cleared protection for sectors 0 through 7 on flash bank 0 +NOTE! DCC downloads have not been enabled, defaulting to slow memory writes. Type 'help dcc'. +> + +	PASS
RES003	STR912	ZY1000	Reset after a power cycle of the target	Reset the target then power cycle the target	Connect via the telnet interface and type `reset halt` after the power was detected	Reset should return without error and the output should contain `target state: halted`	+ + nsed nSRST asserted. + nsed power dropout. + nsed power restore. +RCLK - adaptive +SRST took 85ms to deassert +SRST took 2ms to deassert +JTAG tap: str912.flash tap/device found: 0x04570041 (mfg: 0x020, part: 0x4570, ver: 0x0) +JTAG tap: str912.cpu tap/device found: 0x25966041 (mfg: 0x020, part: 0x5966, ver: 0x2) +JTAG tap: str912.bs tap/device found: 0x2457f041 (mfg: 0x020, part: 0x457f, ver: 0x2) +JTAG tap: str912.bs UNEXPECTED: 0x2457f041 (mfg: 0x020, part: 0x457f, ver: 0x2) +JTAG tap: str912.bs expected 1 of 1: 0x1457f041 (mfg: 0x020, part: 0x457f, ver: 0x1) +Trying to use configured scan chain anyway... +Bypassing JTAG setup events due to errors +SRST took 2ms to deassert +target state: halted +target halted in ARM state due to debug-request, current mode: Supervisor +cpsr: 0x000000d3 pc: 0x00000000 +cleared protection for sectors 0 through 7 on flash bank 0 +NOTE! DCC downloads have not been enabled, defaulting to slow memory writes. Type 'help dcc'. +> reset halt +RCLK - adaptive +SRST took 2ms to deassert +JTAG tap: str912.flash tap/device found: 0x04570041 (mfg: 0x020, part: 0x4570, ver: 0x0) +JTAG tap: str912.cpu tap/device found: 0x25966041 (mfg: 0x020, part: 0x5966, ver: 0x2) +JTAG tap: str912.bs tap/device found: 0x2457f041 (mfg: 0x020, part: 0x457f, ver: 0x2) +JTAG tap: str912.bs UNEXPECTED: 0x2457f041 (mfg: 0x020, part: 0x457f, ver: 0x2) +JTAG tap: str912.bs expected 1 of 1: 0x1457f041 (mfg: 0x020, part: 0x457f, ver: 0x1) +Trying to use configured scan chain anyway... +Bypassing JTAG setup events due to errors +SRST took 2ms to deassert +target state: halted +target halted in ARM state due to debug-request, current mode: Supervisor +cpsr: 0x000000d3 pc: 0x00000000 +NOTE! DCC downloads have not been enabled, defaulting to slow memory writes. Type 'help dcc'. +> + +	PASS
RES004	STR912	ZY1000	Reset halt on a blank target where reset halt is supported	Erase all the content of the flash	Connect via the telnet interface and type `reset halt`	Reset should return without error and the output should contain `target state: halted pc = 0`	+ +> reset halt + RCLK - adaptive +SRST took 2ms to deassert +JTAG tap: str912.flash tap/device found: 0x04570041 (Manufacturer: 0x020, Part: 0x4570, Version: 0x0) +JTAG Tap/device matched +JTAG tap: str912.cpu tap/device found: 0x25966041 (Manufacturer: 0x020, Part: 0x5966, Version: 0x2) +JTAG Tap/device matched +JTAG tap: str912.bs tap/device found: 0x2457f041 (Manufacturer: 0x020, Part: 0x457f, Version: 0x2) +JTAG Tap/device matched +SRST took 2ms to deassert +target state: halted +target halted in ARM state due to debug-request, current mode: Supervisor +cpsr: 0x000000d3 pc: 0x00000000 +> +	PASS
RES005	STR912	ZY1000	Reset halt on a blank target using return clock	Erase all the content of the flash, set the configuration script to use RCLK	Connect via the telnet interface and type `reset halt`	Reset should return without error and the output should contain `target state: halted`	+ + > reset halt +RCLK - adaptive +SRST took 2ms to deassert +JTAG tap: str912.flash tap/device found: 0x04570041 (mfg: 0x020, part: 0x4570, ver: 0x0) +JTAG tap: str912.cpu tap/device found: 0x25966041 (mfg: 0x020, part: 0x5966, ver: 0x2) +JTAG tap: str912.bs tap/device found: 0x2457f041 (mfg: 0x020, part: 0x457f, ver: 0x2) +JTAG tap: str912.bs UNEXPECTED: 0x2457f041 (mfg: 0x020, part: 0x457f, ver: 0x2) +JTAG tap: str912.bs expected 1 of 1: 0x1457f041 (mfg: 0x020, part: 0x457f, ver: 0x1) +Trying to use configured scan chain anyway... +Bypassing JTAG setup events due to errors +SRST took 2ms to deassert +target state: halted +target halted in ARM state due to debug-request, current mode: Supervisor +cpsr: 0x000000d3 pc: 0x00000000 +NOTE! DCC downloads have not been enabled, defaulting to slow memory writes. Type 'help dcc'. +> + +	PASS

+ +

JTAG Speed

+ + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + +

ID	Target	ZY1000	Description	Initial state	Input	Expected output	Actual output	Pass/Fail
SPD001	STR912	ZY1000	16MHz on normal operation	Reset init the target according to RES002	Change speed and exercise a memory access over the JTAG, for example `mdw 0x0 32`	The command should run without any errors. If any JTAG checking errors happen, the test failed	+ +> jtag_khz 16000 +jtag_speed 4 => JTAG clk=16.000000 +16000 kHz +ThumbEE -- incomplete support +target state: halted +target halted in ThumbEE state due to debug-request, current mode: System +cpsr: 0xfdfdffff pc: 0xfdfdfff9 +> mdw 0 32 +0x00000000: 00000000 00000000 ffffffff ffffffff 00000001 ffffffff 00000001 ffffffff +0x00000020: 00000001 00000001 00000001 00000001 00000001 fffffffe fffffffe 00000001 +0x00000040: fffffffe 00000000 00000000 00000000 00000000 00000000 00000000 00000000 +0x00000060: 00000000 00000000 00000000 00000000 ffffffff ffffffff 00000001 00000000 +invalid mode value encountered 0 +cpsr contains invalid mode value - communication failure +ThumbEE -- incomplete support +target state: halted +target halted in ThumbEE state due to debug-request, current mode: System +cpsr: 0xffffffff pc: 0xfffffff8 +> + +	FAIL
SPD002	STR912	ZY1000	8MHz on normal operation	Reset init the target according to RES002	Change speed and exercise a memory access over the JTAG, for example `mdw 0x0 32`	The command should run without any errors. If any JTAG checking errors happen, the test failed	+ `+> jtag_khz 8000 +jtag_speed 8 => JTAG clk=8.000000 +8000 kHz +> halt +invalid mode value encountered 0 +cpsr contains invalid mode value - communication failure +Command handler execution failed +in procedure 'halt' called at file "command.c", line 647 +called at file "command.c", line 361 +Halt timed out, wake up GDB. +> +` +	FAIL
SPD003	STR912	ZY1000	4MHz on normal operation	Reset init the target according to RES002	Change speed and exercise a memory access over the JTAG, for example `mdw 0x0 32`	The command should run without any errors. If any JTAG checking errors happen, the test failed	+ `+> jtag_khz 4000 +jtag_speed 16 => JTAG clk=4.000000 +4000 kHz +> halt +> mdw 0 32 +0x00000000: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff +0x00000020: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff +0x00000040: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff +0x00000060: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff +> +` +	PASS
SPD004	STR912	ZY1000	2MHz on normal operation	Reset init the target according to RES002	Change speed and exercise a memory access over the JTAG, for example `mdw 0x0 32`	The command should run without any errors. If any JTAG checking errors happen, the test failed	+ `+> jtag_khz 2000 +jtag_speed 32 => JTAG clk=2.000000 +2000 kHz +> halt +> mdw 0 32 +0x00000000: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff +0x00000020: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff +0x00000040: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff +0x00000060: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff +> +` +	PASS
SPD005	STR912	ZY1000	RCLK on normal operation	Reset init the target according to RES002	Change speed and exercise a memory access over the JTAG, for example `mdw 0x0 32`	The command should run without any errors. If any JTAG checking errors happen, the test failed	+ `+> jtag_khz 0 +RCLK - adaptive +> halt +> mdw 0 32 +0x00000000: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff +0x00000020: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff +0x00000040: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff +0x00000060: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff +> +` +	PASS

+ +

Debugging

+ + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + +

ID	Target	Interface	Description	Initial state	Input	Expected output	Actual output	Pass/Fail
DBG001	STR912	ZY1000	Load is working	Reset init is working, RAM is accesible, GDB server is started	On the console of the OS: + `arm-elf-gdb test_ram.elf` + `(gdb) target remote ip:port` + `(gdb) load +`	Load should return without error, typical output looks like: + `+ Loading section .text, size 0x14c lma 0x0 + Start address 0x40, load size 332 + Transfer rate: 180 bytes/sec, 332 bytes/write. +` +	`+(gdb) load +Loading section .text, size 0x1a0 lma 0x4000000 +Loading section .rodata, size 0x4 lma 0x40001a0 +Start address 0x4000000, load size 420 +Transfer rate: 29 KB/sec, 210 bytes/write. +(gdb) +`	PASS
DBG002	STR912	ZY1000	Software breakpoint	Load the test_ram.elf application, use instructions from GDB001	In the GDB console: + `+ (gdb) monitor gdb_breakpoint_override soft + force soft breakpoints + (gdb) break main + Breakpoint 1 at 0xec: file src/main.c, line 71. + (gdb) continue + Continuing. +` +	The software breakpoint should be reached, a typical output looks like: + `+ target state: halted + target halted in ARM state due to breakpoint, current mode: Supervisor + cpsr: 0x000000d3 pc: 0x000000ec + + Breakpoint 1, main () at src/main.c:71 + 71 DWORD a = 1; +` +	+ `+(gdb) monitor gdb_breakpoint_override soft +force soft breakpoints +Current language: auto +The current source language is "auto; currently asm". +(gdb) break main +Breakpoint 1 at 0x4000144: file src/main.c, line 69. +(gdb) c +Continuing. + +Breakpoint 1, main () at src/main.c:69 +warning: Source file is more recent than executable. +69 DWORD a = 1; +Current language: auto +The current source language is "auto; currently c". +(gdb) +` +	PASS
DBG003	STR912	ZY1000	Single step in a RAM application	Load the test_ram.elf application, use instructions from GDB001, break in main using the instructions from GDB002	In GDB, type `(gdb) step`	The next instruction should be reached, typical output: + `+ (gdb) step + target state: halted + target halted in ARM state due to single step, current mode: Abort + cpsr: 0x20000097 pc: 0x000000f0 + target state: halted + target halted in ARM state due to single step, current mode: Abort + cpsr: 0x20000097 pc: 0x000000f4 + 72 DWORD b = 2; +` +	+ `+ (gdb) step + 70 DWORD b = 2; + (gdb) +` +	PASS
DBG004	STR912	ZY1000	Software break points are working after a reset	Load the test_ram.elf application, use instructions from GDB001, break in main using the instructions from GDB002	In GDB, type `+ (gdb) monitor reset init + (gdb) load + (gdb) continue +`	The breakpoint should be reached, typical output: + `+ target state: halted + target halted in ARM state due to breakpoint, current mode: Supervisor + cpsr: 0x000000d3 pc: 0x000000ec + + Breakpoint 1, main () at src/main.c:71 + 71 DWORD a = 1; +` +	+(gdb) monitor reset init +RCLK - adaptive +SRST took 2ms to deassert +JTAG tap: str912.flash tap/device found: 0x04570041 (mfg: 0x020, part: 0x4570, ver: 0x0) +JTAG tap: str912.cpu tap/device found: 0x25966041 (mfg: 0x020, part: 0x5966, ver: 0x2) +JTAG tap: str912.bs tap/device found: 0x2457f041 (mfg: 0x020, part: 0x457f, ver: 0x2) +JTAG tap: str912.bs UNEXPECTED: 0x2457f041 (mfg: 0x020, part: 0x457f, ver: 0x2) +JTAG tap: str912.bs expected 1 of 1: 0x1457f041 (mfg: 0x020, part: 0x457f, ver: 0x1) +Trying to use configured scan chain anyway... +Bypassing JTAG setup events due to errors +SRST took 2ms to deassert +target state: halted +target halted in ARM state due to debug-request, current mode: Supervisor +cpsr: 0x000000d3 pc: 0x00000000 +cleared protection for sectors 0 through 7 on flash bank 0 +NOTE! DCC downloads have not been enabled, defaulting to slow memory writes. Type 'help dcc'. +(gdb) load +Loading section .text, size 0x1a0 lma 0x4000000 +Loading section .rodata, size 0x4 lma 0x40001a0 +Start address 0x4000000, load size 420 +Transfer rate: 25 KB/sec, 210 bytes/write. +(gdb) c +Continuing. + +Breakpoint 1, main () at src/main.c:69 +69 DWORD a = 1; +(gdb) +	PASS
DBG005	STR912	ZY1000	Hardware breakpoint	Flash the test_rom.elf application. Make this test after FLA004 has passed	Be sure that `gdb_memory_map` and `gdb_flash_program` are enabled. In GDB, type + `+ (gdb) monitor reset init + (gdb) load + Loading section .text, size 0x194 lma 0x100000 + Start address 0x100040, load size 404 + Transfer rate: 179 bytes/sec, 404 bytes/write. + (gdb) monitor gdb_breakpoint_override hard + force hard breakpoints + (gdb) break main + Breakpoint 1 at 0x100134: file src/main.c, line 69. + (gdb) continue +` +	The breakpoint should be reached, typical output: + `+ Continuing. + + Breakpoint 1, main () at src/main.c:69 + 69 DWORD a = 1; +` +	+ +(gdb) monitor reset init +RCLK - adaptive +SRST took 2ms to deassert +JTAG tap: str912.flash tap/device found: 0x04570041 (mfg: 0x020, part: 0x4570, ver: 0x0) +JTAG tap: str912.cpu tap/device found: 0x25966041 (mfg: 0x020, part: 0x5966, ver: 0x2) +JTAG tap: str912.bs tap/device found: 0x2457f041 (mfg: 0x020, part: 0x457f, ver: 0x2) +JTAG tap: str912.bs UNEXPECTED: 0x2457f041 (mfg: 0x020, part: 0x457f, ver: 0x2) +JTAG tap: str912.bs expected 1 of 1: 0x1457f041 (mfg: 0x020, part: 0x457f, ver: 0x1) +Trying to use configured scan chain anyway... +Bypassing JTAG setup events due to errors +SRST took 2ms to deassert +target state: halted +target halted in ARM state due to debug-request, current mode: Supervisor +cpsr: 0x000000d3 pc: 0x00000000 +cleared protection for sectors 0 through 7 on flash bank 0 +NOTE! DCC downloads have not been enabled, defaulting to slow memory writes. Type 'help dcc'. +(gdb) load +Loading section .text, size 0x1a0 lma 0x0 +Loading section .rodata, size 0x4 lma 0x1a0 +Start address 0x0, load size 420 +Transfer rate: 426 bytes/sec, 210 bytes/write. +(gdb) monitor gdb_breakpoint_override hard +force hard breakpoints +(gdb) break main +Breakpoint 1 at 0x144: file src/main.c, line 69. +(gdb) continue +Continuing. +Note: automatically using hardware breakpoints for read-only addresses. + +Breakpoint 1, main () at src/main.c:69 +warning: Source file is more recent than executable. +69 DWORD a = 1; +Current language: auto +The current source language is "auto; currently c". +(gdb) + +	PASS
DBG006	STR912	ZY1000	Hardware breakpoint is set after a reset	Follow the instructions to flash and insert a hardware breakpoint from DBG005	In GDB, type + `+ (gdb) monitor reset + (gdb) monitor reg pc 0x100000 + pc (/32): 0x00100000 + (gdb) continue +` + where the value inserted in PC is the start address of the application +	The breakpoint should be reached, typical output: + `+ Continuing. + + Breakpoint 1, main () at src/main.c:69 + 69 DWORD a = 1; +` +	+ +(gdb) monitor reset init +RCLK - adaptive +SRST took 2ms to deassert +JTAG tap: str912.flash tap/device found: 0x04570041 (mfg: 0x020, part: 0x4570, ver: 0x0) +JTAG tap: str912.cpu tap/device found: 0x25966041 (mfg: 0x020, part: 0x5966, ver: 0x2) +JTAG tap: str912.bs tap/device found: 0x2457f041 (mfg: 0x020, part: 0x457f, ver: 0x2) +JTAG tap: str912.bs UNEXPECTED: 0x2457f041 (mfg: 0x020, part: 0x457f, ver: 0x2) +JTAG tap: str912.bs expected 1 of 1: 0x1457f041 (mfg: 0x020, part: 0x457f, ver: 0x1) +Trying to use configured scan chain anyway... +Bypassing JTAG setup events due to errors +SRST took 2ms to deassert +target state: halted +target halted in ARM state due to debug-request, current mode: Supervisor +cpsr: 0x000000d3 pc: 0x00000000 +cleared protection for sectors 0 through 7 on flash bank 0 +NOTE! DCC downloads have not been enabled, defaulting to slow memory writes. Type 'help dcc'. +(gdb) c +Continuing. + +Breakpoint 1, main () at src/main.c:69 +69 DWORD a = 1; +(gdb) + +	PASS
DBG007	STR912	ZY1000	Single step in ROM	Flash the test_rom.elf application and set a breakpoint in main, use DBG005. Make this test after FLA004 has passed	Be sure that `gdb_memory_map` and `gdb_flash_program` are enabled. In GDB, type + `+ (gdb) monitor reset + (gdb) load + Loading section .text, size 0x194 lma 0x100000 + Start address 0x100040, load size 404 + Transfer rate: 179 bytes/sec, 404 bytes/write. + (gdb) monitor arm7_9 force_hw_bkpts enable + force hardware breakpoints enabled + (gdb) break main + Breakpoint 1 at 0x100134: file src/main.c, line 69. + (gdb) continue + Continuing. + + Breakpoint 1, main () at src/main.c:69 + 69 DWORD a = 1; + (gdb) step +` +	The breakpoint should be reached, typical output: + `+ target state: halted + target halted in ARM state due to single step, current mode: Supervisor + cpsr: 0x60000013 pc: 0x0010013c + 70 DWORD b = 2; +` +	`+ (gdb) c +Continuing. + +Breakpoint 2, main () at src/main.c:69 +69 DWORD a = 1; +Current language: auto +The current source language is "auto; currently c". +(gdb) step +70 DWORD b = 2; +(gdb) +`	PASS

+ +

RAM access

+Note: these tests are not designed to test/debug the target, but to test functionalities! + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + +

ID	Target	Interface	Description	Initial state	Input	Expected output	Actual output	Pass/Fail
RAM001	STR912	ZY1000	32 bit Write/read RAM	Reset init is working	On the telnet interface + `> mww ram_address 0xdeadbeef 16 + > mdw ram_address 32 +` +	The commands should execute without error. A clear failure is a memory access exception. The result of running the commands should be a list of 16 locations 32bit long containing 0xdeadbeef. + `+ > mww 0x0 0xdeadbeef 16 + > mdw 0x0 32 + 0x00000000: deadbeef deadbeef deadbeef deadbeef deadbeef deadbeef deadbeef deadbeef + 0x00000020: deadbeef deadbeef deadbeef deadbeef deadbeef deadbeef deadbeef deadbeef + 0x00000040: e1a00000 e59fa51c e59f051c e04aa000 00080017 00009388 00009388 00009388 + 0x00000060: 00009388 0002c2c0 0002c2c0 000094f8 000094f4 00009388 00009388 00009388 +` +	`+> mww 0x4000000 0xdeadbeef 16 +> mdw 0x4000000 32 +0x04000000: deadbeef deadbeef deadbeef deadbeef deadbeef deadbeef deadbeef deadbeef +0x04000020: deadbeef deadbeef deadbeef deadbeef deadbeef deadbeef deadbeef deadbeef +0x04000040: e580100c e3a01802 e5801010 e3a01018 e5801018 e59f00a8 e59f10a8 e5801000 +0x04000060: e3a00806 ee2f0f11 e321f0d7 e59fd098 e321f0db e59fd094 e321f0d3 e59fd090 +> +`	PASS
RAM002	STR912	ZY1000	16 bit Write/read RAM	Reset init is working	On the telnet interface + `> mwh ram_address 0xbeef 16 + > mdh ram_address 32 +` +	The commands should execute without error. A clear failure is a memory access exception. The result of running the commands should be a list of 16 locations 16bit long containing 0xbeef. + `+ > mwh 0x0 0xbeef 16 + > mdh 0x0 32 + 0x00000000: beef beef beef beef beef beef beef beef beef beef beef beef beef beef beef beef + 0x00000020: 00e0 0000 021c 0000 0240 0000 026c 0000 0288 0000 0000 0000 0388 0000 0350 0000 + > +` +	`+> mwh 0x4000000 0xbeef 16 +> mdh 0x4000000 32 +0x04000000: beef beef beef beef beef beef beef beef beef beef beef beef beef beef beef beef +0x04000020: beef dead beef dead beef dead beef dead beef dead beef dead beef dead beef dead +> +`	PASS
RAM003	STR912	ZY1000	8 bit Write/read RAM	Reset init is working	On the telnet interface + `> mwb ram_address 0xab 16 + > mdb ram_address 32 +` +	The commands should execute without error. A clear failure is a memory access exception. The result of running the commands should be a list of 16 locations 8bit long containing 0xab. + `+ > mwb ram_address 0xab 16 + > mdb ram_address 32 + 0x00000000: ab ab ab ab ab ab ab ab ab ab ab ab ab ab ab ab 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 + > +` +	`+> mwb 0x4000000 0xab 16 +> mdb 0x4000000 32 +0x04000000: ab ab ab ab ab ab ab ab ab ab ab ab ab ab ab ab ef be ef be ef be ef be ef be ef be ef be ef be +> +`	PASS

+ + + +

Flash access

+ + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + +

ID	Target	Interface	Description	Initial state	Input	Expected output	Actual output	Pass/Fail
FLA001	STR912	ZY1000	Flash probe	Reset init is working	On the telnet interface: + `> flash probe 0` +	The command should execute without error. The output should state the name of the flash and the starting address. An example of output: + `flash 'ecosflash' found at 0x01000000` +	+ `+ > flash probe 0 + flash 'str9x' found at 0x00000000 + > +` +	PASS
FLA002	STR912	ZY1000	flash fillw	Reset init is working, flash is probed	On the telnet interface + `> flash fillw 0x1000000 0xdeadbeef 16 +` +	The commands should execute without error. The output looks like: + `+ wrote 64 bytes to 0x01000000 in 11.610000s (0.091516 kb/s) +` + To verify the contents of the flash: + `+ > mdw 0x1000000 32 + 0x01000000: deadbeef deadbeef deadbeef deadbeef deadbeef deadbeef deadbeef deadbeef + 0x01000020: deadbeef deadbeef deadbeef deadbeef deadbeef deadbeef deadbeef deadbeef + 0x01000040: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff + 0x01000060: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff +` +	`+> flash fillw 0x0 0xdeadbeef 16 +wrote 64 bytes to 0x00000000 in 0.020000s (3.125 kb/s) +> mdw 0 32 +0x00000000: deadbeef deadbeef deadbeef deadbeef deadbeef deadbeef deadbeef deadbeef +0x00000020: deadbeef deadbeef deadbeef deadbeef deadbeef deadbeef deadbeef deadbeef +0x00000040: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff +0x00000060: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff +> +`	PASS
FLA003	STR912	ZY1000	Flash erase	Reset init is working, flash is probed	On the telnet interface + `> flash erase_address 0x1000000 0x20000 +` +	The commands should execute without error. + `+ erased address 0x01000000 length 131072 in 4.970000s +` + To check that the flash has been erased, read at different addresses. The result should always be 0xff. + `+ > mdw 0x1000000 32 + 0x01000000: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff + 0x01000020: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff + 0x01000040: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff + 0x01000060: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff +` +	`+> flash erase_address 0 0x20000 +erased address 0x00000000 (length 131072) in 1.970000s (64.975 kb/s) +> mdw 0 32 +0x00000000: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff +0x00000020: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff +0x00000040: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff +0x00000060: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff +> +`	PASS
FLA004	STR912	ZY1000	Entire flash erase	Reset init is working, flash is probed	On the telnet interface + `> flash erase_address 0x0 0x80000 +` +	The commands should execute without error. + `+ erased address 0x01000000 length 8192 in 4.970000s +` + To check that the flash has been erased, read at different addresses. The result should always be 0xff. + `+ > mdw 0x1000000 32 + 0x01000000: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff + 0x01000020: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff + 0x01000040: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff + 0x01000060: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff +` +	`+> flash erase_address 0 0x80000 + erased address 0x00000000 length 524288 in 1.020000s + +> mdw 0 32 + 0x00000000: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff +0x00000020: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff +0x00000040: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff +0x00000060: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff +`	PASS
FLA005	STR912	ZY1000	Loading to flash from GDB	Reset init is working, flash is probed, connectivity to GDB server is working	Start GDB using a ROM elf image, eg: arm-elf-gdb test_rom.elf. + `+ (gdb) target remote ip:port + (gdb) monitor reset + (gdb) load + Loading section .text, size 0x194 lma 0x100000 + Start address 0x100040, load size 404 + Transfer rate: 179 bytes/sec, 404 bytes/write. + (gdb) monitor verify_image path_to_elf_file +` +	The output should look like: + `+ verified 404 bytes in 5.060000s +` + The failure message is something like: + `Verify operation failed address 0x00200000. Was 0x00 instead of 0x18` +	+ `+(gdb) load +Loading section .text, size 0x1a0 lma 0x0 +Loading section .rodata, size 0x4 lma 0x1a0 +Start address 0x0, load size 420 +Transfer rate: 425 bytes/sec, 210 bytes/write. +(gdb) moni verify_image /tftp/10.0.0.194/test_rom.elf +verified 420 bytes in 0.350000s (1.172 kb/s) +(gdb) +` +	PASS

+ + + \ No newline at end of file -- cgit v1.2.3