Board, rev A.rev-a

1 files changed, 718 insertions, 0 deletions

diff --git a/firmware/makefile b/firmware/makefile
new file mode 100644
index 0000000..a123bcd
--- /dev/null
+++ b/firmware/makefile
@@ -0,0 +1,718 @@
+# Hey Emacs, this is a -*- makefile -*-
+#----------------------------------------------------------------------------
+# WinAVR Makefile Template written by Eric B. Weddington, Jörg Wunsch, et al.
+#  >> Modified for use with the LUFA project. <<
+#
+# Released to the Public Domain
+#
+# Additional material for this makefile was written by:
+# Peter Fleury
+# Tim Henigan
+# Colin O'Flynn
+# Reiner Patommel
+# Markus Pfaff
+# Sander Pool
+# Frederik Rouleau
+# Carlos Lamas
+# Dean Camera
+# Opendous Inc.
+# Denver Gingerich
+#
+#----------------------------------------------------------------------------
+# On command line:
+#
+# make all = Make software.
+#
+# make clean = Clean out built project files.
+#
+# make coff = Convert ELF to AVR COFF.
+#
+# make extcoff = Convert ELF to AVR Extended COFF.
+#
+# make program = Download the hex file to the device, using avrdude.
+#                Please customize the avrdude settings below first!
+#
+# make dfu = Download the hex file to the device, using dfu-programmer (must
+#            have dfu-programmer installed).
+#
+# make flip = Download the hex file to the device, using Atmel FLIP (must
+#             have Atmel FLIP installed).
+#
+# make dfu-ee = Download the eeprom file to the device, using dfu-programmer
+#               (must have dfu-programmer installed).
+#
+# make flip-ee = Download the eeprom file to the device, using Atmel FLIP
+#                (must have Atmel FLIP installed).
+#
+# make doxygen = Generate DoxyGen documentation for the project (must have
+#                DoxyGen installed)
+#
+# make debug = Start either simulavr or avarice as specified for debugging,
+#              with avr-gdb or avr-insight as the front end for debugging.
+#
+# make filename.s = Just compile filename.c into the assembler code only.
+#
+# make filename.i = Create a preprocessed source file for use in submitting
+#                   bug reports to the GCC project.
+#
+# To rebuild project do "make clean" then "make all".
+#----------------------------------------------------------------------------
+
+
+# MCU name
+MCU = at90usb162
+
+
+# Target board (see library "Board Types" documentation, NONE for projects not requiring
+# LUFA board drivers). If USER is selected, put custom board drivers in a directory called
+# "Board" inside the application directory.
+BOARD = USER
+
+
+# Processor frequency.
+#     This will define a symbol, F_CPU, in all source code files equal to the
+#     processor frequency in Hz. You can then use this symbol in your source code to
+#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
+#     automatically to create a 32-bit value in your source code.
+#
+#     This will be an integer division of F_CLOCK below, as it is sourced by
+#     F_CLOCK after it has run through any CPU prescalers. Note that this value
+#     does not *change* the processor frequency - it should merely be updated to
+#     reflect the processor speed set externally so that the code can use accurate
+#     software delays.
+F_CPU = 16000000
+
+
+# Input clock frequency.
+#     This will define a symbol, F_CLOCK, in all source code files equal to the
+#     input clock frequency (before any prescaling is performed) in Hz. This value may
+#     differ from F_CPU if prescaling is used on the latter, and is required as the
+#     raw input clock is fed directly to the PLL sections of the AVR for high speed
+#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
+#     at the end, this will be done automatically to create a 32-bit value in your
+#     source code.
+#
+#     If no clock division is performed on the input clock inside the AVR (via the
+#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
+F_CLOCK = $(F_CPU)
+
+
+# Output format. (can be srec, ihex, binary)
+FORMAT = ihex
+
+
+# Target file name (without extension).
+TARGET = VirtualSerial
+
+
+# Object files directory
+#     To put object files in current directory, use a dot (.), do NOT make
+#     this an empty or blank macro!
+OBJDIR = .
+
+
+# Path to the LUFA library
+LUFA_PATH = .
+
+
+# LUFA library compile-time options and predefined tokens
+LUFA_OPTS  = -D USB_DEVICE_ONLY
+LUFA_OPTS += -D FIXED_CONTROL_ENDPOINT_SIZE=8
+LUFA_OPTS += -D FIXED_NUM_CONFIGURATIONS=1
+LUFA_OPTS += -D USE_FLASH_DESCRIPTORS
+LUFA_OPTS += -D USE_STATIC_OPTIONS="(USB_DEVICE_OPT_FULLSPEED | USB_OPT_REG_ENABLED | USB_OPT_AUTO_PLL)"
+
+
+# Create the LUFA source path variables by including the LUFA root makefile
+include $(LUFA_PATH)/LUFA/makefile
+
+
+# List C source files here. (C dependencies are automatically generated.)
+SRC = $(TARGET).c                                                 \
+	  Descriptors.c                                               \
+	  $(LUFA_SRC_USB)                                             \
+	  $(LUFA_SRC_USBCLASS)
+
+
+# List C++ source files here. (C dependencies are automatically generated.)
+CPPSRC =
+
+
+# List Assembler source files here.
+#     Make them always end in a capital .S.  Files ending in a lowercase .s
+#     will not be considered source files but generated files (assembler
+#     output from the compiler), and will be deleted upon "make clean"!
+#     Even though the DOS/Win* filesystem matches both .s and .S the same,
+#     it will preserve the spelling of the filenames, and gcc itself does
+#     care about how the name is spelled on its command-line.
+ASRC =
+
+
+# Optimization level, can be [0, 1, 2, 3, s].
+#     0 = turn off optimization. s = optimize for size.
+#     (Note: 3 is not always the best optimization level. See avr-libc FAQ.)
+OPT = s
+
+
+# Debugging format.
+#     Native formats for AVR-GCC's -g are dwarf-2 [default] or stabs.
+#     AVR Studio 4.10 requires dwarf-2.
+#     AVR [Extended] COFF format requires stabs, plus an avr-objcopy run.
+DEBUG = dwarf-2
+
+
+# List any extra directories to look for include files here.
+#     Each directory must be seperated by a space.
+#     Use forward slashes for directory separators.
+#     For a directory that has spaces, enclose it in quotes.
+EXTRAINCDIRS = $(LUFA_PATH)/
+
+
+# Compiler flag to set the C Standard level.
+#     c89   = "ANSI" C
+#     gnu89 = c89 plus GCC extensions
+#     c99   = ISO C99 standard (not yet fully implemented)
+#     gnu99 = c99 plus GCC extensions
+CSTANDARD = -std=c99
+
+
+# Place -D or -U options here for C sources
+CDEFS  = -DF_CPU=$(F_CPU)UL
+CDEFS += -DF_CLOCK=$(F_CLOCK)UL
+CDEFS += -DBOARD=BOARD_$(BOARD)
+CDEFS += $(LUFA_OPTS)
+
+
+# Place -D or -U options here for ASM sources
+ADEFS  = -DF_CPU=$(F_CPU)
+ADEFS += -DF_CLOCK=$(F_CLOCK)UL
+ADEFS += -DBOARD=BOARD_$(BOARD)
+ADEFS += $(LUFA_OPTS)
+
+# Place -D or -U options here for C++ sources
+CPPDEFS  = -DF_CPU=$(F_CPU)UL
+CPPDEFS += -DF_CLOCK=$(F_CLOCK)UL
+CPPDEFS += -DBOARD=BOARD_$(BOARD)
+CPPDEFS += $(LUFA_OPTS)
+#CPPDEFS += -D__STDC_LIMIT_MACROS
+#CPPDEFS += -D__STDC_CONSTANT_MACROS
+
+
+
+#---------------- Compiler Options C ----------------
+#  -g*:          generate debugging information
+#  -O*:          optimization level
+#  -f...:        tuning, see GCC manual and avr-libc documentation
+#  -Wall...:     warning level
+#  -Wa,...:      tell GCC to pass this to the assembler.
+#    -adhlns...: create assembler listing
+CFLAGS = -g$(DEBUG)
+CFLAGS += $(CDEFS)
+CFLAGS += -O$(OPT)
+CFLAGS += -funsigned-char
+CFLAGS += -funsigned-bitfields
+CFLAGS += -ffunction-sections
+CFLAGS += -fno-inline-small-functions
+CFLAGS += -fpack-struct
+CFLAGS += -fshort-enums
+CFLAGS += -fno-strict-aliasing
+CFLAGS += -Wall
+CFLAGS += -Wstrict-prototypes
+#CFLAGS += -mshort-calls
+#CFLAGS += -fno-unit-at-a-time
+#CFLAGS += -Wundef
+#CFLAGS += -Wunreachable-code
+#CFLAGS += -Wsign-compare
+CFLAGS += -Wa,-adhlns=$(<:%.c=$(OBJDIR)/%.lst)
+CFLAGS += $(patsubst %,-I%,$(EXTRAINCDIRS))
+CFLAGS += $(CSTANDARD)
+
+
+#---------------- Compiler Options C++ ----------------
+#  -g*:          generate debugging information
+#  -O*:          optimization level
+#  -f...:        tuning, see GCC manual and avr-libc documentation
+#  -Wall...:     warning level
+#  -Wa,...:      tell GCC to pass this to the assembler.
+#    -adhlns...: create assembler listing
+CPPFLAGS = -g$(DEBUG)
+CPPFLAGS += $(CPPDEFS)
+CPPFLAGS += -O$(OPT)
+CPPFLAGS += -funsigned-char
+CPPFLAGS += -funsigned-bitfields
+CPPFLAGS += -fpack-struct
+CPPFLAGS += -fshort-enums
+CPPFLAGS += -fno-exceptions
+CPPFLAGS += -Wall
+CPPFLAGS += -Wundef
+#CPPFLAGS += -mshort-calls
+#CPPFLAGS += -fno-unit-at-a-time
+#CPPFLAGS += -Wstrict-prototypes
+#CPPFLAGS += -Wunreachable-code
+#CPPFLAGS += -Wsign-compare
+CPPFLAGS += -Wa,-adhlns=$(<:%.cpp=$(OBJDIR)/%.lst)
+CPPFLAGS += $(patsubst %,-I%,$(EXTRAINCDIRS))
+#CPPFLAGS += $(CSTANDARD)
+
+
+#---------------- Assembler Options ----------------
+#  -Wa,...:   tell GCC to pass this to the assembler.
+#  -adhlns:   create listing
+#  -gstabs:   have the assembler create line number information; note that
+#             for use in COFF files, additional information about filenames
+#             and function names needs to be present in the assembler source
+#             files -- see avr-libc docs [FIXME: not yet described there]
+#  -listing-cont-lines: Sets the maximum number of continuation lines of hex
+#       dump that will be displayed for a given single line of source input.
+ASFLAGS = $(ADEFS) -Wa,-adhlns=$(<:%.S=$(OBJDIR)/%.lst),-gstabs,--listing-cont-lines=100
+
+
+#---------------- Library Options ----------------
+# Minimalistic printf version
+PRINTF_LIB_MIN = -Wl,-u,vfprintf -lprintf_min
+
+# Floating point printf version (requires MATH_LIB = -lm below)
+PRINTF_LIB_FLOAT = -Wl,-u,vfprintf -lprintf_flt
+
+# If this is left blank, then it will use the Standard printf version.
+PRINTF_LIB =
+#PRINTF_LIB = $(PRINTF_LIB_MIN)
+#PRINTF_LIB = $(PRINTF_LIB_FLOAT)
+
+
+# Minimalistic scanf version
+SCANF_LIB_MIN = -Wl,-u,vfscanf -lscanf_min
+
+# Floating point + %[ scanf version (requires MATH_LIB = -lm below)
+SCANF_LIB_FLOAT = -Wl,-u,vfscanf -lscanf_flt
+
+# If this is left blank, then it will use the Standard scanf version.
+SCANF_LIB =
+#SCANF_LIB = $(SCANF_LIB_MIN)
+#SCANF_LIB = $(SCANF_LIB_FLOAT)
+
+
+MATH_LIB = -lm
+
+
+# List any extra directories to look for libraries here.
+#     Each directory must be seperated by a space.
+#     Use forward slashes for directory separators.
+#     For a directory that has spaces, enclose it in quotes.
+EXTRALIBDIRS =
+
+
+
+#---------------- External Memory Options ----------------
+
+# 64 KB of external RAM, starting after internal RAM (ATmega128!),
+# used for variables (.data/.bss) and heap (malloc()).
+#EXTMEMOPTS = -Wl,-Tdata=0x801100,--defsym=__heap_end=0x80ffff
+
+# 64 KB of external RAM, starting after internal RAM (ATmega128!),
+# only used for heap (malloc()).
+#EXTMEMOPTS = -Wl,--section-start,.data=0x801100,--defsym=__heap_end=0x80ffff
+
+EXTMEMOPTS =
+
+
+
+#---------------- Linker Options ----------------
+#  -Wl,...:     tell GCC to pass this to linker.
+#    -Map:      create map file
+#    --cref:    add cross reference to  map file
+LDFLAGS  = -Wl,-Map=$(TARGET).map,--cref
+LDFLAGS += -Wl,--relax
+LDFLAGS += -Wl,--gc-sections
+LDFLAGS += $(EXTMEMOPTS)
+LDFLAGS += $(patsubst %,-L%,$(EXTRALIBDIRS))
+LDFLAGS += $(PRINTF_LIB) $(SCANF_LIB) $(MATH_LIB)
+#LDFLAGS += -T linker_script.x
+
+
+
+#---------------- Programming Options (avrdude) ----------------
+
+# Programming hardware
+# Type: avrdude -c ?
+# to get a full listing.
+#
+AVRDUDE_PROGRAMMER = jtag2dw
+
+# com1 = serial port. Use lpt1 to connect to parallel port.
+AVRDUDE_PORT = usb
+
+AVRDUDE_WRITE_FLASH = -U flash:w:$(TARGET).hex
+#AVRDUDE_WRITE_EEPROM = -U eeprom:w:$(TARGET).eep
+
+
+# Uncomment the following if you want avrdude's erase cycle counter.
+# Note that this counter needs to be initialized first using -Yn,
+# see avrdude manual.
+#AVRDUDE_ERASE_COUNTER = -y
+
+# Uncomment the following if you do /not/ wish a verification to be
+# performed after programming the device.
+#AVRDUDE_NO_VERIFY = -V
+
+# Increase verbosity level.  Please use this when submitting bug
+# reports about avrdude. See <http://savannah.nongnu.org/projects/avrdude>
+# to submit bug reports.
+#AVRDUDE_VERBOSE = -v -v
+
+AVRDUDE_FLAGS = -p $(MCU) -P $(AVRDUDE_PORT) -c $(AVRDUDE_PROGRAMMER)
+AVRDUDE_FLAGS += $(AVRDUDE_NO_VERIFY)
+AVRDUDE_FLAGS += $(AVRDUDE_VERBOSE)
+AVRDUDE_FLAGS += $(AVRDUDE_ERASE_COUNTER)
+
+
+
+#---------------- Debugging Options ----------------
+
+# For simulavr only - target MCU frequency.
+DEBUG_MFREQ = $(F_CPU)
+
+# Set the DEBUG_UI to either gdb or insight.
+# DEBUG_UI = gdb
+DEBUG_UI = insight
+
+# Set the debugging back-end to either avarice, simulavr.
+DEBUG_BACKEND = avarice
+#DEBUG_BACKEND = simulavr
+
+# GDB Init Filename.
+GDBINIT_FILE = __avr_gdbinit
+
+# When using avarice settings for the JTAG
+JTAG_DEV = /dev/com1
+
+# Debugging port used to communicate between GDB / avarice / simulavr.
+DEBUG_PORT = 4242
+
+# Debugging host used to communicate between GDB / avarice / simulavr, normally
+#     just set to localhost unless doing some sort of crazy debugging when
+#     avarice is running on a different computer.
+DEBUG_HOST = localhost
+
+
+
+#============================================================================
+
+
+# Define programs and commands.
+SHELL = sh
+CC = avr-gcc
+OBJCOPY = avr-objcopy
+OBJDUMP = avr-objdump
+SIZE = avr-size
+AR = avr-ar rcs
+NM = avr-nm
+AVRDUDE = ~gus/src/upstream/avrdude/avrdude/avrdude
+REMOVE = rm -f
+REMOVEDIR = rm -rf
+COPY = cp
+WINSHELL = cmd
+
+
+# Define Messages
+# English
+MSG_ERRORS_NONE = Errors: none
+MSG_BEGIN = -------- begin --------
+MSG_END = --------  end  --------
+MSG_SIZE_BEFORE = Size before:
+MSG_SIZE_AFTER = Size after:
+MSG_COFF = Converting to AVR COFF:
+MSG_EXTENDED_COFF = Converting to AVR Extended COFF:
+MSG_FLASH = Creating load file for Flash:
+MSG_EEPROM = Creating load file for EEPROM:
+MSG_EXTENDED_LISTING = Creating Extended Listing:
+MSG_SYMBOL_TABLE = Creating Symbol Table:
+MSG_LINKING = Linking:
+MSG_COMPILING = Compiling C:
+MSG_COMPILING_CPP = Compiling C++:
+MSG_ASSEMBLING = Assembling:
+MSG_CLEANING = Cleaning project:
+MSG_CREATING_LIBRARY = Creating library:
+
+
+
+
+# Define all object files.
+OBJ = $(SRC:%.c=$(OBJDIR)/%.o) $(CPPSRC:%.cpp=$(OBJDIR)/%.o) $(ASRC:%.S=$(OBJDIR)/%.o)
+
+# Define all listing files.
+LST = $(SRC:%.c=$(OBJDIR)/%.lst) $(CPPSRC:%.cpp=$(OBJDIR)/%.lst) $(ASRC:%.S=$(OBJDIR)/%.lst)
+
+
+# Compiler flags to generate dependency files.
+GENDEPFLAGS = -MMD -MP -MF .dep/$(@F).d
+
+
+# Combine all necessary flags and optional flags.
+# Add target processor to flags.
+ALL_CFLAGS = -mmcu=$(MCU) -I. $(CFLAGS) $(GENDEPFLAGS)
+ALL_CPPFLAGS = -mmcu=$(MCU) -I. -x c++ $(CPPFLAGS) $(GENDEPFLAGS)
+ALL_ASFLAGS = -mmcu=$(MCU) -I. -x assembler-with-cpp $(ASFLAGS)
+
+
+
+
+
+# Default target.
+all: begin gccversion sizebefore build sizeafter end
+
+# Change the build target to build a HEX file or a library.
+build: elf hex eep lss sym
+#build: lib
+
+
+elf: $(TARGET).elf
+hex: $(TARGET).hex
+eep: $(TARGET).eep
+lss: $(TARGET).lss
+sym: $(TARGET).sym
+LIBNAME=lib$(TARGET).a
+lib: $(LIBNAME)
+
+
+
+# Eye candy.
+# AVR Studio 3.x does not check make's exit code but relies on
+# the following magic strings to be generated by the compile job.
+begin:
+	@echo
+	@echo $(MSG_BEGIN)
+
+end:
+	@echo $(MSG_END)
+	@echo
+
+
+# Display size of file.
+HEXSIZE = $(SIZE) --target=$(FORMAT) $(TARGET).hex
+ELFSIZE = $(SIZE) $(MCU_FLAG) $(FORMAT_FLAG) $(TARGET).elf
+MCU_FLAG = $(shell $(SIZE) --help | grep -- --mcu > /dev/null && echo --mcu=$(MCU) )
+FORMAT_FLAG = $(shell $(SIZE) --help | grep -- --format=.*avr > /dev/null && echo --format=avr )
+
+
+sizebefore:
+	@if test -f $(TARGET).elf; then echo; echo $(MSG_SIZE_BEFORE); $(ELFSIZE); \
+	2>/dev/null; echo; fi
+
+sizeafter:
+	@if test -f $(TARGET).elf; then echo; echo $(MSG_SIZE_AFTER); $(ELFSIZE); \
+	2>/dev/null; echo; fi
+
+
+
+# Display compiler version information.
+gccversion :
+	@$(CC) --version
+
+
+# Program the device.
+program: $(TARGET).hex $(TARGET).eep
+#	$(AVRDUDE) $(AVRDUDE_FLAGS) $(AVRDUDE_WRITE_FLASH) $(AVRDUDE_WRITE_EEPROM)
+	#avarice -w -f VirtualSerial.hex -P at90usb162 -2 -j usb
+	avrdude -c avr109 -p usb162 -P /dev/ttyACM0 -U flash:w:VirtualSerial.hex
+
+reset:
+	avarice -P at90usb162 -2 -j usb -R
+
+flip: $(TARGET).hex
+	batchisp -hardware usb -device $(MCU) -operation erase f
+	batchisp -hardware usb -device $(MCU) -operation loadbuffer $(TARGET).hex program
+	batchisp -hardware usb -device $(MCU) -operation start reset 0
+
+dfu: $(TARGET).hex
+	dfu-programmer $(MCU) erase
+	dfu-programmer $(MCU) flash $(TARGET).hex
+	dfu-programmer $(MCU) reset
+
+flip-ee: $(TARGET).hex $(TARGET).eep
+	$(COPY) $(TARGET).eep $(TARGET)eep.hex
+	batchisp -hardware usb -device $(MCU) -operation memory EEPROM erase
+	batchisp -hardware usb -device $(MCU) -operation memory EEPROM loadbuffer $(TARGET)eep.hex program
+	batchisp -hardware usb -device $(MCU) -operation start reset 0
+	$(REMOVE) $(TARGET)eep.hex
+
+dfu-ee: $(TARGET).hex $(TARGET).eep
+	dfu-programmer $(MCU) eeprom-flash $(TARGET).eep
+	dfu-programmer $(MCU) reset
+
+
+# Generate avr-gdb config/init file which does the following:
+#     define the reset signal, load the target file, connect to target, and set
+#     a breakpoint at main().
+gdb-config:
+	@$(REMOVE) $(GDBINIT_FILE)
+	@echo define reset >> $(GDBINIT_FILE)
+	@echo SIGNAL SIGHUP >> $(GDBINIT_FILE)
+	@echo end >> $(GDBINIT_FILE)
+	@echo file $(TARGET).elf >> $(GDBINIT_FILE)
+	@echo target remote $(DEBUG_HOST):$(DEBUG_PORT)  >> $(GDBINIT_FILE)
+ifeq ($(DEBUG_BACKEND),simulavr)
+	@echo load  >> $(GDBINIT_FILE)
+endif
+	@echo break main >> $(GDBINIT_FILE)
+
+debug: gdb-config $(TARGET).elf
+ifeq ($(DEBUG_BACKEND), avarice)
+	@echo Starting AVaRICE - Press enter when "waiting to connect" message displays.
+	@$(WINSHELL) /c start avarice --jtag $(JTAG_DEV) --erase --program --file \
+	$(TARGET).elf $(DEBUG_HOST):$(DEBUG_PORT)
+	@$(WINSHELL) /c pause
+
+else
+	@$(WINSHELL) /c start simulavr --gdbserver --device $(MCU) --clock-freq \
+	$(DEBUG_MFREQ) --port $(DEBUG_PORT)
+endif
+	@$(WINSHELL) /c start avr-$(DEBUG_UI) --command=$(GDBINIT_FILE)
+
+
+
+
+# Convert ELF to COFF for use in debugging / simulating in AVR Studio or VMLAB.
+COFFCONVERT = $(OBJCOPY) --debugging
+COFFCONVERT += --change-section-address .data-0x800000
+COFFCONVERT += --change-section-address .bss-0x800000
+COFFCONVERT += --change-section-address .noinit-0x800000
+COFFCONVERT += --change-section-address .eeprom-0x810000
+
+
+
+coff: $(TARGET).elf
+	@echo
+	@echo $(MSG_COFF) $(TARGET).cof
+	$(COFFCONVERT) -O coff-avr $< $(TARGET).cof
+
+
+extcoff: $(TARGET).elf
+	@echo
+	@echo $(MSG_EXTENDED_COFF) $(TARGET).cof
+	$(COFFCONVERT) -O coff-ext-avr $< $(TARGET).cof
+
+
+
+# Create final output files (.hex, .eep) from ELF output file.
+%.hex: %.elf
+	@echo
+	@echo $(MSG_FLASH) $@
+	$(OBJCOPY) -O $(FORMAT) -R .eeprom -R .fuse -R .lock $< $@
+
+%.eep: %.elf
+	@echo
+	@echo $(MSG_EEPROM) $@
+	-$(OBJCOPY) -j .eeprom --set-section-flags=.eeprom="alloc,load" \
+	--change-section-lma .eeprom=0 --no-change-warnings -O $(FORMAT) $< $@ || exit 0
+
+# Create extended listing file from ELF output file.
+%.lss: %.elf
+	@echo
+	@echo $(MSG_EXTENDED_LISTING) $@
+	$(OBJDUMP) -h -S -z $< > $@
+
+# Create a symbol table from ELF output file.
+%.sym: %.elf
+	@echo
+	@echo $(MSG_SYMBOL_TABLE) $@
+	$(NM) -n $< > $@
+
+
+
+# Create library from object files.
+.SECONDARY : $(TARGET).a
+.PRECIOUS : $(OBJ)
+%.a: $(OBJ)
+	@echo
+	@echo $(MSG_CREATING_LIBRARY) $@
+	$(AR) $@ $(OBJ)
+
+
+# Link: create ELF output file from object files.
+.SECONDARY : $(TARGET).elf
+.PRECIOUS : $(OBJ)
+%.elf: $(OBJ)
+	@echo
+	@echo $(MSG_LINKING) $@
+	$(CC) $(ALL_CFLAGS) $^ --output $@ $(LDFLAGS)
+
+
+# Compile: create object files from C source files.
+$(OBJDIR)/%.o : %.c
+	@echo
+	@echo $(MSG_COMPILING) $<
+	$(CC) -c $(ALL_CFLAGS) $< -o $@
+
+
+# Compile: create object files from C++ source files.
+$(OBJDIR)/%.o : %.cpp
+	@echo
+	@echo $(MSG_COMPILING_CPP) $<
+	$(CC) -c $(ALL_CPPFLAGS) $< -o $@
+
+
+# Compile: create assembler files from C source files.
+%.s : %.c
+	$(CC) -S $(ALL_CFLAGS) $< -o $@
+
+
+# Compile: create assembler files from C++ source files.
+%.s : %.cpp
+	$(CC) -S $(ALL_CPPFLAGS) $< -o $@
+
+
+# Assemble: create object files from assembler source files.
+$(OBJDIR)/%.o : %.S
+	@echo
+	@echo $(MSG_ASSEMBLING) $<
+	$(CC) -c $(ALL_ASFLAGS) $< -o $@
+
+
+# Create preprocessed source for use in sending a bug report.
+%.i : %.c
+	$(CC) -E -mmcu=$(MCU) -I. $(CFLAGS) $< -o $@
+
+
+# Target: clean project.
+clean: begin clean_list end
+
+clean_list :
+	@echo
+	@echo $(MSG_CLEANING)
+	$(REMOVE) $(TARGET).hex
+	$(REMOVE) $(TARGET).eep
+	$(REMOVE) $(TARGET).cof
+	$(REMOVE) $(TARGET).elf
+	$(REMOVE) $(TARGET).map
+	$(REMOVE) $(TARGET).sym
+	$(REMOVE) $(TARGET).lss
+	$(REMOVE) $(SRC:%.c=$(OBJDIR)/%.o) $(CPPSRC:%.cpp=$(OBJDIR)/%.o) $(ASRC:%.S=$(OBJDIR)/%.o)
+	$(REMOVE) $(SRC:%.c=$(OBJDIR)/%.lst) $(CPPSRC:%.cpp=$(OBJDIR)/%.lst) $(ASRC:%.S=$(OBJDIR)/%.lst)
+	$(REMOVE) $(SRC:.c=.s)
+	$(REMOVE) $(SRC:.c=.d)
+	$(REMOVE) $(SRC:.c=.i)
+	$(REMOVEDIR) .dep
+
+doxygen:
+	@echo Generating Project Documentation...
+	@doxygen Doxygen.conf
+	@echo Documentation Generation Complete.
+
+clean_doxygen:
+	rm -rf Documentation
+
+# Create object files directory
+$(shell mkdir $(OBJDIR) 2>/dev/null)
+
+
+# Include the dependency files.
+-include $(shell mkdir .dep 2>/dev/null) $(wildcard .dep/*)
+
+
+# Listing of phony targets.
+.PHONY : all begin finish end sizebefore sizeafter gccversion \
+build elf hex eep lss sym coff extcoff doxygen clean          \
+clean_list clean_doxygen program dfu flip flip-ee dfu-ee      \
+debug gdb-config
+