diff options
Diffstat (limited to 'tmp/STM32F10x_StdPeriph_Lib_V3.5.0/Project/STM32F10x_StdPeriph_Examples/USART/IrDA/Transmit/readme.txt')
| -rw-r--r-- | tmp/STM32F10x_StdPeriph_Lib_V3.5.0/Project/STM32F10x_StdPeriph_Examples/USART/IrDA/Transmit/readme.txt | 141 |
1 files changed, 141 insertions, 0 deletions
diff --git a/tmp/STM32F10x_StdPeriph_Lib_V3.5.0/Project/STM32F10x_StdPeriph_Examples/USART/IrDA/Transmit/readme.txt b/tmp/STM32F10x_StdPeriph_Lib_V3.5.0/Project/STM32F10x_StdPeriph_Examples/USART/IrDA/Transmit/readme.txt new file mode 100644 index 0000000..c9ea1a8 --- /dev/null +++ b/tmp/STM32F10x_StdPeriph_Lib_V3.5.0/Project/STM32F10x_StdPeriph_Examples/USART/IrDA/Transmit/readme.txt @@ -0,0 +1,141 @@ +/** + @page USART_IrDA_Transmit USART IrDA Transmit example + + @verbatim + ******************** (C) COPYRIGHT 2011 STMicroelectronics ******************* + * @file USART/IrDA/Transmit/readme.txt + * @author MCD Application Team + * @version V3.5.0 + * @date 08-April-2011 + * @brief Description of the USART IrDA Transmit example. + ****************************************************************************** + * THE PRESENT FIRMWARE WHICH IS FOR GUIDANCE ONLY AIMS AT PROVIDING CUSTOMERS + * WITH CODING INFORMATION REGARDING THEIR PRODUCTS IN ORDER FOR THEM TO SAVE + * TIME. AS A RESULT, STMICROELECTRONICS SHALL NOT BE HELD LIABLE FOR ANY + * DIRECT, INDIRECT OR CONSEQUENTIAL DAMAGES WITH RESPECT TO ANY CLAIMS ARISING + * FROM THE CONTENT OF SUCH FIRMWARE AND/OR THE USE MADE BY CUSTOMERS OF THE + * CODING INFORMATION CONTAINED HEREIN IN CONNECTION WITH THEIR PRODUCTS. + ****************************************************************************** + @endverbatim + +@par Example Description + +This example provides a basic communication USARTy IrDA transmit mode. Five pins, +configured in input floating mode, are used to select the byte to be send at +each pin state change. USARTy can be USART3 or USART2 depending on the +STMicroelectronics EVAL board you are using. + +These bytes are: + - 0x00 if no key (JOY_NONE) pressed + - 0x01 if JOY_SEL pin state change + - 0x02 if JOY_DOWN pin state change + - 0x03 if JOY_LEFT pin state change + - 0x04 if JOY_RIGHT pin state change + - 0x05 if JOY_UP pin state change + +USARTy configured as follow: + - BaudRate = 115200 baud + - Word Length = 8 Bits + - One Stop Bit + - No parity + - Hardware flow control disabled (RTS and CTS signals) + - Receive and transmit enabled + +The USART IrDA example provides two IrDA program: transmitter&receiver and requires two boards +to be able to run the full demonstration: + - one board will act as IrDA transmitter + - one board will act as IrDA receiver + + +@par Directory contents + + - USART/IrDA/Transmit/platform_config.h Evaluation board specific configuration file + - USART/IrDA/Transmit/stm32f10x_conf.h Library Configuration file + - USART/IrDA/Transmit/stm32f10x_it.h Interrupt handlers header file + - USART/IrDA/Transmit/stm32f10x_it.c Interrupt handlers + - USART/IrDA/Transmit/main.c Main program + - USART/IrDA/Transmit/system_stm32f10x.c STM32F10x system source file + +@par Hardware and Software environment + + - This example runs on STM32F10x Connectivity line, High-Density, High-Density + Value line, Medium-Density, XL-Density, Medium-Density Value line, Low-Density + and Low-Density Value line Devices. + + - This example has been tested with STMicroelectronics STM32100E-EVAL (High-Density + Value line), STM32100B-EVAL (Medium-Density Value line), STM3210C-EVAL (Connectivity line), + STM3210E-EVAL (High-Density and XL-Density) and STM3210B-EVAL (Medium-Density) + evaluation boards and can be easily tailored to any other supported device + and development board. + To select the STMicroelectronics evaluation board used to run the example, + uncomment the corresponding line in USART/IrDA/Transmit/platform_config.h or the stm32_eval.h file + + - STM32100E-EVAL Set-up + - Use DOWN push-button connected to pin PD.03 + - Use UP push-button connected to pin PG.15 + - Use SEL push-button connected to pin PG.07 + - Use RIGHT push-button connected to pin PG.13 + - Use RIGHT push-button connected to pin PG.14 + - Use an IrDA transceiver connected to the USART3 Tx and Rx pins (U16 + connector, JP15 jumper must be fitted). + + - STM32100B-EVAL Set-up + - Use DOWN push-button connected to pin PD.14 + - Use UP push-button connected to pin PD.08 + - Use SEL push-button connected to pin PD.12 + - Use RIGHT push-button connected to pin PE.01 + - Use RIGHT push-button connected to pin PE.00 + - Use an IrDA transceiver connected to the USART3 Tx and Rx pins (U14 + connector, JP11 jumper must be fitted). + + - STM3210C-EVAL Set-up + - The JoyStick push buttons are connected to the IO Expander on I2C. + - Use an IrDA transceiver connected to the USART2 Tx and Rx pins (U12 + connector, JP16 should be in position 1<-->2). + + - STM3210E-EVAL Set-up + - Use DOWN push-button connected to pin PD.03 + - Use UP push-button connected to pin PG.15 + - Use SEL push-button connected to pin PG.07 + - Use RIGHT push-button connected to pin PG.13 + - Use RIGHT push-button connected to pin PG.14 + - Use an IrDA transceiver connected to the USART3 Tx and Rx pins (U13 + connector, JP21 and JP22 jumper must be fitted). + + - STM3210B-EVAL Set-up + - Use DOWN push-button connected to pin PD.14 + - Use UP push-button connected to pin PD.08 + - Use SEL push-button connected to pin PD.12 + - Use RIGHT push-button connected to pin PE.00 + - Use RIGHT push-button connected to pin PE.01 + - Use an IrDA transceiver connected to the USART3 Tx and Rx pins (U11 + connector, JP5 jumper must be fitted). + +@par How to use it ? + +In order to make the program work, you must do the following : + - Copy all source files from this example folder to the template folder under + Project\STM32F10x_StdPeriph_Template + - Open your preferred toolchain + - Rebuild all files and load your image into target memory + - Run the example + +@note + - Low-density Value line devices are STM32F100xx microcontrollers where the + Flash memory density ranges between 16 and 32 Kbytes. + - Low-density devices are STM32F101xx, STM32F102xx and STM32F103xx + microcontrollers where the Flash memory density ranges between 16 and 32 Kbytes. + - Medium-density Value line devices are STM32F100xx microcontrollers where + the Flash memory density ranges between 64 and 128 Kbytes. + - Medium-density devices are STM32F101xx, STM32F102xx and STM32F103xx + microcontrollers where the Flash memory density ranges between 64 and 128 Kbytes. + - High-density Value line devices are STM32F100xx microcontrollers where + the Flash memory density ranges between 256 and 512 Kbytes. + - High-density devices are STM32F101xx and STM32F103xx microcontrollers where + the Flash memory density ranges between 256 and 512 Kbytes. + - XL-density devices are STM32F101xx and STM32F103xx microcontrollers where + the Flash memory density ranges between 512 and 1024 Kbytes. + - Connectivity line devices are STM32F105xx and STM32F107xx microcontrollers. + + * <h3><center>© COPYRIGHT 2011 STMicroelectronics</center></h3> + */ |