- add missing svn props

git-svn-id: svn://svn.berlios.de/openocd/trunk@554 b42882b7-edfa-0310-969c-e2dbd0fdcd60

4 files changed, 209 insertions, 209 deletions

diff --git a/src/target/event/pxa255_reset.script b/src/target/event/pxa255_reset.script
index a4a97165..bc9fa822 100644
--- a/src/target/event/pxa255_reset.script
+++ b/src/target/event/pxa255_reset.script
@@ -1,74 +1,74 @@
-#configuration file for PXA250 Evaluation Board

-# -----------------------------------------------------

-#

-xscale cp15   15      0x00002001  #Enable CP0 and CP13 access

-#

-# setup GPIO

-#

-mww    0x40E00018  0x00008000  #CPSR0

-sleep   20

-mww    0x40E0001C  0x00000002  #GPSR1

-sleep   20

-mww    0x40E00020  0x00000008  #GPSR2

-sleep   20

-mww    0x40E0000C  0x00008000  #GPDR0

-sleep   20

-mww    0x40E00054  0x80000000  #GAFR0_L

-sleep   20

-mww    0x40E00058  0x00188010  #GAFR0_H

-sleep   20

-mww    0x40E0005C  0x60908018  #GAFR1_L

-sleep   20

-mww    0x40E0000C  0x0280E000  #GPDR0

-sleep   20

-mww    0x40E00010  0x821C88B2  #GPDR1

-sleep   20

-mww    0x40E00014  0x000F03DB  #GPDR2

-sleep   20

-mww    0x40E00000  0x000F03DB  #GPLR0

-sleep   20

-

-

-mww    0x40F00004  0x00000020  #PSSR

-sleep   20

-

-#

-# setup memory controller

-#

-mww    0x48000008  0x01111998  #MSC0

-sleep   20

-mww    0x48000010  0x00047ff0  #MSC2

-sleep   20

-mww    0x48000014  0x00000000  #MECR

-sleep   20

-mww    0x48000028  0x00010504  #MCMEM0

-sleep   20

-mww    0x4800002C  0x00010504  #MCMEM1

-sleep   20

-mww    0x48000030  0x00010504  #MCATT0

-sleep   20

-mww    0x48000034  0x00010504  #MCATT1

-sleep   20

-mww    0x48000038  0x00004715  #MCIO0

-sleep   20

-mww    0x4800003C  0x00004715  #MCIO1

-sleep   20

-#

-mww    0x48000004  0x03CA4018  #MDREF

-sleep   20

-mww    0x48000004  0x004B4018  #MDREF

-sleep   20

-mww    0x48000004  0x000B4018  #MDREF

-sleep   20

-mww    0x48000004  0x000BC018  #MDREF

-sleep   20

-mww    0x48000000  0x00001AC8  #MDCNFG

-sleep   20

-

-sleep   20

-

-mww    0x48000000  0x00001AC9  #MDCNFG

-sleep   20

-mww    0x48000040  0x00000000  #MDMRS

-sleep   20

-

+#configuration file for PXA250 Evaluation Board
+# -----------------------------------------------------
+#
+xscale cp15   15      0x00002001  #Enable CP0 and CP13 access
+#
+# setup GPIO
+#
+mww    0x40E00018  0x00008000  #CPSR0
+sleep   20
+mww    0x40E0001C  0x00000002  #GPSR1
+sleep   20
+mww    0x40E00020  0x00000008  #GPSR2
+sleep   20
+mww    0x40E0000C  0x00008000  #GPDR0
+sleep   20
+mww    0x40E00054  0x80000000  #GAFR0_L
+sleep   20
+mww    0x40E00058  0x00188010  #GAFR0_H
+sleep   20
+mww    0x40E0005C  0x60908018  #GAFR1_L
+sleep   20
+mww    0x40E0000C  0x0280E000  #GPDR0
+sleep   20
+mww    0x40E00010  0x821C88B2  #GPDR1
+sleep   20
+mww    0x40E00014  0x000F03DB  #GPDR2
+sleep   20
+mww    0x40E00000  0x000F03DB  #GPLR0
+sleep   20
+
+
+mww    0x40F00004  0x00000020  #PSSR
+sleep   20
+
+#
+# setup memory controller
+#
+mww    0x48000008  0x01111998  #MSC0
+sleep   20
+mww    0x48000010  0x00047ff0  #MSC2
+sleep   20
+mww    0x48000014  0x00000000  #MECR
+sleep   20
+mww    0x48000028  0x00010504  #MCMEM0
+sleep   20
+mww    0x4800002C  0x00010504  #MCMEM1
+sleep   20
+mww    0x48000030  0x00010504  #MCATT0
+sleep   20
+mww    0x48000034  0x00010504  #MCATT1
+sleep   20
+mww    0x48000038  0x00004715  #MCIO0
+sleep   20
+mww    0x4800003C  0x00004715  #MCIO1
+sleep   20
+#
+mww    0x48000004  0x03CA4018  #MDREF
+sleep   20
+mww    0x48000004  0x004B4018  #MDREF
+sleep   20
+mww    0x48000004  0x000B4018  #MDREF
+sleep   20
+mww    0x48000004  0x000BC018  #MDREF
+sleep   20
+mww    0x48000000  0x00001AC8  #MDCNFG
+sleep   20
+
+sleep   20
+
+mww    0x48000000  0x00001AC9  #MDCNFG
+sleep   20
+mww    0x48000040  0x00000000  #MDMRS
+sleep   20
+
diff --git a/src/target/event/str912_reset.script b/src/target/event/str912_reset.script
index bbec5976..c3d68104 100644
--- a/src/target/event/str912_reset.script
+++ b/src/target/event/str912_reset.script
@@ -1,22 +1,22 @@
-mww 0xFFFFFD44, 0x00008000 #Disable watchdog

-mww 0xFFFFFC20, 0x00000601 #Enable Main oscillator

-sleep 20

-mww 0xFFFFFC30, 0x00000001 #Switch master clock to CPU clock, write 1 to PMC_MCKR

-sleep 20

-

-

-# -- Remap Flash Bank 0 at address 0x0 and Bank 1 at address 0x80000,

-#    when the bank 0 is the boot bank, then enable the Bank 1. */

-

-mww 0x54000000, 0x4 #BOOT BANK Size = (2^4) * 32 = 512KB

-mww 0x54000004, 0x2 #NON BOOT BANK Size = (2^2) * 8 = 32KB

-mww 0x5400000C, 0x0 #BOOT BANK Address = 0x0

-mww 0x54000010, 0x20000 #NON BOOT BANK Address = 0x80000

-mww 0x54000018, 0x18 #Enable CS on both banks

-

-# -- Enable 96K RAM */

-mww 0x5C002034, 0x0191 # PFQBC enabled / DTCM & AHB wait-states disabled

-arm966e cp15 15, 0x60000 #Set bits 17-18 (DTCM/ITCM order bits) of the Core Configuration Control Register

-

-str9x flash_config 0 4 2 0 0x80000

-flash protect 0 0 7 off

+mww 0xFFFFFD44, 0x00008000 #Disable watchdog
+mww 0xFFFFFC20, 0x00000601 #Enable Main oscillator
+sleep 20
+mww 0xFFFFFC30, 0x00000001 #Switch master clock to CPU clock, write 1 to PMC_MCKR
+sleep 20
+
+
+# -- Remap Flash Bank 0 at address 0x0 and Bank 1 at address 0x80000,
+#    when the bank 0 is the boot bank, then enable the Bank 1. */
+
+mww 0x54000000, 0x4 #BOOT BANK Size = (2^4) * 32 = 512KB
+mww 0x54000004, 0x2 #NON BOOT BANK Size = (2^2) * 8 = 32KB
+mww 0x5400000C, 0x0 #BOOT BANK Address = 0x0
+mww 0x54000010, 0x20000 #NON BOOT BANK Address = 0x80000
+mww 0x54000018, 0x18 #Enable CS on both banks
+
+# -- Enable 96K RAM */
+mww 0x5C002034, 0x0191 # PFQBC enabled / DTCM & AHB wait-states disabled
+arm966e cp15 15, 0x60000 #Set bits 17-18 (DTCM/ITCM order bits) of the Core Configuration Control Register
+
+str9x flash_config 0 4 2 0 0x80000
+flash protect 0 0 7 off
diff --git a/src/target/event/wi-9c_reset.script b/src/target/event/wi-9c_reset.script
index abb50216..b648106c 100644
--- a/src/target/event/wi-9c_reset.script
+++ b/src/target/event/wi-9c_reset.script
@@ -1,70 +1,70 @@
-mww 0x90600104 0x33313333

-mww 0xA0700000 0x00000001  # Enable the memory controller.

-mww 0xA0700024 0x00000006  # Set the refresh counter 6

-mww 0xA0700028 0x00000001  # 

-mww 0xA0700030 0x00000001  # Set the precharge period

-mww 0xA0700034 0x00000004  # Active to precharge command period is 16 clock cycles

-mww 0xA070003C 0x00000001  # tAPR

-mww 0xA0700040 0x00000005  # tDAL

-mww 0xA0700044 0x00000001  # tWR

-mww 0xA0700048 0x00000006  # tRC 32 clock cycles  

-mww 0xA070004C 0x00000006  # tRFC 32 clock cycles

-mww 0xA0700054 0x00000001  # tRRD

-mww 0xA0700058 0x00000001  # tMRD

-mww 0xA0700100 0x00004280  # Dynamic Config 0 (cs4) 

-mww 0xA0700120 0x00004280  # Dynamic Config 1 (cs5)

-mww 0xA0700140 0x00004280  # Dynamic Config 2 (cs6)

-mww 0xA0700160 0x00004280  # Dynamic Config 3 (cs7)

-#

-mww 0xA0700104 0x00000203  # CAS latency is 2 at 100 MHz

-mww 0xA0700124 0x00000203  # CAS latency is 2 at 100 MHz

-mww 0xA0700144 0x00000203  # CAS latency is 2 at 100 MHz

-mww 0xA0700164 0x00000203  # CAS latency is 2 at 100 MHz

-#

-mww 0xA0700020 0x00000103  # issue SDRAM PALL command

-#

-mww 0xA0700024 0x00000001  # Set the refresh counter to be as small as possible

-#

-# Add some dummy writes to give the SDRAM time to settle, it needs two

-# AHB clock cycles, here we poke in the debugger flag, this lets

-# the software know that we are in the debugger

-mww 0xA0900000 0x00000002

-mww 0xA0900000 0x00000002

-mww 0xA0900000 0x00000002

-mww 0xA0900000 0x00000002

-mww 0xA0900000 0x00000002

-#

-mdw 0xA0900000 

-mdw 0xA0900000 

-mdw 0xA0900000 

-mdw 0xA0900000 

-mdw 0xA0900000 

-#

-mww 0xA0700024 0x00000030 # Set the refresh counter to 30

-mww 0xA0700020 0x00000083 # Issue SDRAM MODE command

-#

-# Next we perform a read of RAM.

-# mw = move word.

-mdw 0x00022000

-# mw 0x00022000:P, r3  # 22000 for cas2 latency, 32000 for cas 3

-#

-mww 0xA0700020 0x00000003   # issue SDRAM NORMAL command

-mww 0xA0700100 0x00084280   # Enable buffer access

-mww 0xA0700120 0x00084280   # Enable buffer access

-mww 0xA0700140 0x00084280   # Enable buffer access

-mww 0xA0700160 0x00084280   # Enable buffer access

-

-#Set byte lane state (static mem 1)"

-mww 0xA0700220, 0x00000082

-#Flash Start

-mww 0xA09001F8, 0x50000000

-#Flash Mask Reg

-mww 0xA09001FC, 0xFF000001

-mww 0xA0700028, 0x00000001

-

-#  RAMAddr = 0x00020000

-#  RAMSize = 0x00004000

-

-# Set the processor mode

-reg cpsr 0xd3

-

+mww 0x90600104 0x33313333
+mww 0xA0700000 0x00000001  # Enable the memory controller.
+mww 0xA0700024 0x00000006  # Set the refresh counter 6
+mww 0xA0700028 0x00000001  # 
+mww 0xA0700030 0x00000001  # Set the precharge period
+mww 0xA0700034 0x00000004  # Active to precharge command period is 16 clock cycles
+mww 0xA070003C 0x00000001  # tAPR
+mww 0xA0700040 0x00000005  # tDAL
+mww 0xA0700044 0x00000001  # tWR
+mww 0xA0700048 0x00000006  # tRC 32 clock cycles  
+mww 0xA070004C 0x00000006  # tRFC 32 clock cycles
+mww 0xA0700054 0x00000001  # tRRD
+mww 0xA0700058 0x00000001  # tMRD
+mww 0xA0700100 0x00004280  # Dynamic Config 0 (cs4) 
+mww 0xA0700120 0x00004280  # Dynamic Config 1 (cs5)
+mww 0xA0700140 0x00004280  # Dynamic Config 2 (cs6)
+mww 0xA0700160 0x00004280  # Dynamic Config 3 (cs7)
+#
+mww 0xA0700104 0x00000203  # CAS latency is 2 at 100 MHz
+mww 0xA0700124 0x00000203  # CAS latency is 2 at 100 MHz
+mww 0xA0700144 0x00000203  # CAS latency is 2 at 100 MHz
+mww 0xA0700164 0x00000203  # CAS latency is 2 at 100 MHz
+#
+mww 0xA0700020 0x00000103  # issue SDRAM PALL command
+#
+mww 0xA0700024 0x00000001  # Set the refresh counter to be as small as possible
+#
+# Add some dummy writes to give the SDRAM time to settle, it needs two
+# AHB clock cycles, here we poke in the debugger flag, this lets
+# the software know that we are in the debugger
+mww 0xA0900000 0x00000002
+mww 0xA0900000 0x00000002
+mww 0xA0900000 0x00000002
+mww 0xA0900000 0x00000002
+mww 0xA0900000 0x00000002
+#
+mdw 0xA0900000 
+mdw 0xA0900000 
+mdw 0xA0900000 
+mdw 0xA0900000 
+mdw 0xA0900000 
+#
+mww 0xA0700024 0x00000030 # Set the refresh counter to 30
+mww 0xA0700020 0x00000083 # Issue SDRAM MODE command
+#
+# Next we perform a read of RAM.
+# mw = move word.
+mdw 0x00022000
+# mw 0x00022000:P, r3  # 22000 for cas2 latency, 32000 for cas 3
+#
+mww 0xA0700020 0x00000003   # issue SDRAM NORMAL command
+mww 0xA0700100 0x00084280   # Enable buffer access
+mww 0xA0700120 0x00084280   # Enable buffer access
+mww 0xA0700140 0x00084280   # Enable buffer access
+mww 0xA0700160 0x00084280   # Enable buffer access
+
+#Set byte lane state (static mem 1)"
+mww 0xA0700220, 0x00000082
+#Flash Start
+mww 0xA09001F8, 0x50000000
+#Flash Mask Reg
+mww 0xA09001FC, 0xFF000001
+mww 0xA0700028, 0x00000001
+
+#  RAMAddr = 0x00020000
+#  RAMSize = 0x00004000
+
+# Set the processor mode
+reg cpsr 0xd3
+
diff --git a/src/target/event/xba_revA3.script b/src/target/event/xba_revA3.script
index 3d011014..e58185e2 100644
--- a/src/target/event/xba_revA3.script
+++ b/src/target/event/xba_revA3.script
@@ -1,43 +1,43 @@
-#Written by: Michael Schwingen <rincewind@discworld.dascon.de>

-#############################################################################

-# setup expansion bus CS, disable external wdt

-#############################################################################

-mww 0xc4000000  0xbd113842  #CS0  : Flash, write enabled @0x50000000

-mww 0xc4000004  0x94d10013  #CS1

-mww 0xc4000008  0x95960003  #CS2

-mww 0xc400000c  0x00000000  #CS3

-mww 0xc4000010  0x80900003  #CS4

-mww 0xc4000014  0x9d520003  #CS5

-mww 0xc4000018  0x81860001  #CS6

-mww 0xc400001c  0x80900003  #CS7

-

-#############################################################################

-# init SDRAM controller: 16MB, one bank, CL3

-#############################################################################

-mww 0xCC000000  0x2A # SDRAM_CFG: 64MBit, CL3

-mww 0xCC000004     0 # disable refresh

-mww 0xCC000008     3 # NOP

-sleep 100

-mww 0xCC000004  2100 # set refresh counter

-mww 0xCC000008     2 # Precharge All Banks

-sleep 100

-mww 0xCC000008     4 # Auto Refresh

-mww 0xCC000008     4 # Auto Refresh

-mww 0xCC000008     4 # Auto Refresh

-mww 0xCC000008     4 # Auto Refresh

-mww 0xCC000008     4 # Auto Refresh

-mww 0xCC000008     4 # Auto Refresh

-mww 0xCC000008     4 # Auto Refresh

-mww 0xCC000008     4 # Auto Refresh

-mww 0xCC000008     1 # Mode Select CL3

-

-#mww 0xc4000020  0xffffee # CFG0: remove expansion bus boot flash

-#mirror at 0x00000000

-

-#big endian

-reg XSCALE_CTRL 0xF8

-

-#

-# detect flash

-#

-flash probe 0

+#Written by: Michael Schwingen <rincewind@discworld.dascon.de>
+#############################################################################
+# setup expansion bus CS, disable external wdt
+#############################################################################
+mww 0xc4000000  0xbd113842  #CS0  : Flash, write enabled @0x50000000
+mww 0xc4000004  0x94d10013  #CS1
+mww 0xc4000008  0x95960003  #CS2
+mww 0xc400000c  0x00000000  #CS3
+mww 0xc4000010  0x80900003  #CS4
+mww 0xc4000014  0x9d520003  #CS5
+mww 0xc4000018  0x81860001  #CS6
+mww 0xc400001c  0x80900003  #CS7
+
+#############################################################################
+# init SDRAM controller: 16MB, one bank, CL3
+#############################################################################
+mww 0xCC000000  0x2A # SDRAM_CFG: 64MBit, CL3
+mww 0xCC000004     0 # disable refresh
+mww 0xCC000008     3 # NOP
+sleep 100
+mww 0xCC000004  2100 # set refresh counter
+mww 0xCC000008     2 # Precharge All Banks
+sleep 100
+mww 0xCC000008     4 # Auto Refresh
+mww 0xCC000008     4 # Auto Refresh
+mww 0xCC000008     4 # Auto Refresh
+mww 0xCC000008     4 # Auto Refresh
+mww 0xCC000008     4 # Auto Refresh
+mww 0xCC000008     4 # Auto Refresh
+mww 0xCC000008     4 # Auto Refresh
+mww 0xCC000008     4 # Auto Refresh
+mww 0xCC000008     1 # Mode Select CL3
+
+#mww 0xc4000020  0xffffee # CFG0: remove expansion bus boot flash
+#mirror at 0x00000000
+
+#big endian
+reg XSCALE_CTRL 0xF8
+
+#
+# detect flash
+#
+flash probe 0