Move TCL script files -- Step 1 of 2:

- Move src/target/{interface,target,board,test}/ into src/tcl/
- Remove existing rules in src/Makefile.am and src/target/Makefile.am.
- Add Makefile.am handling of *.cfg and *.tcl files in top Makefile.am:
  - Add dist-hook to include such files under src/tcl in the distribution.
  - Add install-data-hook to install contents of '$(top_srcdir)/src/tcl/'.
  - Add uninstall-hook to remove the installed script files.
- Change paths to (un)install script files in '$(pkgdatadir)/scripts'.


git-svn-id: svn://svn.berlios.de/openocd/trunk@1918 b42882b7-edfa-0310-969c-e2dbd0fdcd60

1 files changed, 61 insertions, 0 deletions

diff --git a/src/tcl/target/aduc702x.cfg b/src/tcl/target/aduc702x.cfg
new file mode 100644
index 00000000..ef1beb78
--- /dev/null
+++ b/src/tcl/target/aduc702x.cfg
@@ -0,0 +1,61 @@
+## -*- tcl -*-
+##
+
+
+if { [info exists CHIPNAME] } {	
+   set  _CHIPNAME $CHIPNAME    
+} else {	 
+   set  _CHIPNAME s3c2410
+}
+
+if { [info exists ENDIAN] } {	
+   set  _ENDIAN $ENDIAN    
+} else {	 
+  # This config file was defaulting to big endian..
+   set  _ENDIAN little
+}
+
+if { [info exists CPUTAPID] } {	
+   set  _CPUTAPID $CPUTAPID    
+} else {	 
+   set  _CPUTAPID 0xffffffff
+}
+
+
+jtag_nsrst_delay 200
+jtag_ntrst_delay 200
+
+# This is for the case that TRST/SRST is not wired on your JTAG adaptor.
+# Don't really need them anyways.  
+reset_config none
+
+## JTAG scan chain
+#format L IRC IRCM IDCODE (Length, IR Capture, IR Capture Mask, IDCODE)
+jtag newtap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_CPUTAPID
+
+##
+## Target configuration
+##
+set _TARGETNAME [format "%s.cpu" $_CHIPNAME]
+target create $_TARGETNAME arm7tdmi -endian $_ENDIAN -chain-position $_TARGETNAME
+
+# allocate the entire SRAM as working area
+$_TARGETNAME configure -work-area-phys 0x10000 -work-area-size 0x2000
+
+## flash configuration
+# only target number is needed
+flash bank aduc702x 0 0 0 0 0
+
+## If you use the watchdog, the following code makes sure that the board
+## doesn't reboot when halted via JTAG.  Yes, on the older generation
+## AdUC702x, timer3 continues running even when the CPU is halted.
+
+proc watchdog_service {} {
+    global watchdog_hdl
+    mww 0xffff036c 0
+#    puts "watchdog!!"
+    set watchdog_hdl [after 500 watchdog_service]
+}
+
+$_TARGETNAME configure -event reset-halt-post {  watchdog_service }
+$_TARGETNAME configure -event old-pre_resume { global watchdog_hdl; after cancel $watchdog_hdl }