Move TCL script files -- Step 1 of 2:

- Move src/target/{interface,target,board,test}/ into src/tcl/
- Remove existing rules in src/Makefile.am and src/target/Makefile.am.
- Add Makefile.am handling of *.cfg and *.tcl files in top Makefile.am:
  - Add dist-hook to include such files under src/tcl in the distribution.
  - Add install-data-hook to install contents of '$(top_srcdir)/src/tcl/'.
  - Add uninstall-hook to remove the installed script files.
- Change paths to (un)install script files in '$(pkgdatadir)/scripts'.


git-svn-id: svn://svn.berlios.de/openocd/trunk@1918 b42882b7-edfa-0310-969c-e2dbd0fdcd60

1 files changed, 92 insertions, 0 deletions

diff --git a/src/tcl/target/ti_dm355.cfg b/src/tcl/target/ti_dm355.cfg
new file mode 100644
index 00000000..1bd5cda5
--- /dev/null
+++ b/src/tcl/target/ti_dm355.cfg
@@ -0,0 +1,92 @@
+#
+# Texas Instruments DaVinci family:  TMS320DM355
+#
+if { [info exists CHIPNAME] } {
+   set  _CHIPNAME $CHIPNAME
+} else {
+   set  _CHIPNAME dm355
+}
+if { [info exists ENDIAN] } {
+   set  _ENDIAN $ENDIAN
+} else {
+   set  _ENDIAN little
+}
+
+#
+# For now, expect EMU0/EMU1 jumpered LOW (not TI's default) so ARM and ETB
+# are enabled without making ICEpick route ARM and ETB into the JTAG chain.
+#
+# Also note:  when running without RTCK before the PLLs are set up, you
+# may need to slow the JTAG clock down quite a lot (under 2 MHz).
+#
+
+# Subsidiary TAP: ARM ETB11, with scan chain for 4K of ETM trace buffer
+if { [info exists ETB_TAPID ] } {
+   set _ETB_TAPID $ETB_TAPID
+} else {
+   set _ETB_TAPID 0x2b900f0f
+}
+jtag newtap $_CHIPNAME etb -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_ETB_TAPID
+
+# Subsidiary TAP: ARM926ejs with scan chains for ARM Debug, EmbeddedICE-RT, ETM.
+if { [info exists CPU_TAPID ] } {
+   set _CPU_TAPID $CPU_TAPID
+} else {
+   set _CPU_TAPID 0x07926001
+}
+jtag newtap $_CHIPNAME arm -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_CPU_TAPID
+
+# Primary TAP: ICEpick (JTAG route controller) and boundary scan
+if { [info exists JRC_TAPID ] } {
+   set _JRC_TAPID $JRC_TAPID
+} else {
+   set _JRC_TAPID 0x0b73b02f
+}
+jtag newtap $_CHIPNAME jrc -irlen 6 -ircapture 0x1 -irmask 0x3f -expected-id $_JRC_TAPID
+
+################
+
+# various symbol definitions, to avoid hard-wiring addresses
+# and enable some sharing of DaVinci-family utility code
+global dm355
+set dm355 [ dict create ]
+
+# Physical addresses for controllers and memory
+# (Some of these are valid for many DaVinci family chips)
+dict set dm355 sram0		0x00010000
+dict set dm355 sram1		0x00014000
+dict set dm355 sysbase		0x01c40000
+dict set dm355 pllc1		0x01c40800
+dict set dm355 pllc2		0x01c40c00
+dict set dm355 psc		0x01c41000
+dict set dm355 gpio		0x01c67000
+dict set dm355 a_emif		0x01e10000
+dict set dm355 a_emif_cs0	0x02000000
+dict set dm355 a_emif_cs1	0x04000000
+dict set dm355 ddr_emif		0x20000000
+dict set dm355 ddr		0x80000000
+
+source [find target/davinci.cfg]
+
+################
+# GDB target:  the ARM, using SRAM1 for scratch.  SRAM0 (also 16K)
+# and the ETB memory (4K) are other options, while trace is unused.
+set _TARGETNAME $_CHIPNAME.arm
+
+target create $_TARGETNAME arm926ejs -endian $_ENDIAN -chain-position $_TARGETNAME
+
+# NOTE that work-area-virt presumes a Linux 2.6.30-rc2+ kernel,
+# and that the work area is used only with a kernel mmu context ...
+$_TARGETNAME configure \
+	-work-area-virt [expr 0xfffe0000 + 0x4000] \
+	-work-area-phys [dict get $dm355 sram1] \
+	-work-area-size 0x4000 \
+	-work-area-backup 0
+
+arm7_9 dbgrq enable
+arm7_9 fast_memory_access enable
+arm7_9 dcc_downloads enable
+
+# trace setup
+etm config $_TARGETNAME 16 normal full etb
+etb config $_TARGETNAME $_CHIPNAME.etb