A working version for my EFM board.

1 files changed, 77 insertions, 0 deletions

diff --git a/tcl/target/efm32.cfg b/tcl/target/efm32.cfg
new file mode 100644
index 00000000..de5384cb
--- /dev/null
+++ b/tcl/target/efm32.cfg
@@ -0,0 +1,77 @@
+# script for Energy Micro's efm32
+
+if { [info exists CHIPNAME] } {
+   set  _CHIPNAME $CHIPNAME
+} else {
+   set  _CHIPNAME efm32
+}
+
+if { [info exists ENDIAN] } {
+   set  _ENDIAN $ENDIAN
+} else {
+   set  _ENDIAN little
+}
+
+# Work-area is a space in RAM used for flash programming
+# By default use 16kB
+if { [info exists WORKAREASIZE] } {
+   set  _WORKAREASIZE $WORKAREASIZE
+} else {
+   set  _WORKAREASIZE 0x4000
+}
+
+# JTAG speed should be <= F_CPU/6. F_CPU after reset is 8MHz, so use F_JTAG = 1MHz
+adapter_khz 1000
+
+adapter_nsrst_delay 100
+# jtag_ntrst_delay 100
+
+#jtag scan chain
+if { [info exists CPUTAPID ] } {
+   set _CPUTAPID $CPUTAPID
+} else {
+  # See STM Document RM0008
+  # Section 26.6.3
+   set _CPUTAPID 0x3ba00477
+}
+# jtag newtap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_CPUTAPID
+swd newtap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_CPUTAPID
+
+if { [info exists BSTAPID ] } {
+   # FIXME this never gets used to override defaults...
+   set _BSTAPID $BSTAPID
+} else {
+  # See STM Document RM0008
+  # Section 29.6.2
+  # Low density devices, Rev A
+  set _BSTAPID1 0x06412041
+  # Medium density devices, Rev A
+  set _BSTAPID2 0x06410041
+  # Medium density devices, Rev B and Rev Z
+  set _BSTAPID3 0x16410041
+  set _BSTAPID4 0x06420041
+  # High density devices, Rev A
+  set _BSTAPID5 0x06414041
+  # Connectivity line devices, Rev A and Rev Z
+  set _BSTAPID6 0x06418041
+  # XL line devices, Rev A
+  set _BSTAPID7 0x06430041
+}
+# jtag newtap $_CHIPNAME bs -irlen 5 -expected-id $_BSTAPID1 \
+swd newtap $_CHIPNAME bs -irlen 5 -expected-id $_BSTAPID1 \
+	-expected-id $_BSTAPID2 -expected-id $_BSTAPID3 \
+	-expected-id $_BSTAPID4 -expected-id $_BSTAPID5 \
+	-expected-id $_BSTAPID6 -expected-id $_BSTAPID7
+
+set _TARGETNAME $_CHIPNAME.cpu
+target create $_TARGETNAME cortex_m3 -endian $_ENDIAN -chain-position $_TARGETNAME
+
+$_TARGETNAME configure -work-area-phys 0x20000000 -work-area-size $_WORKAREASIZE -work-area-backup 0
+
+# flash size will be probed
+set _FLASHNAME $_CHIPNAME.flash
+flash bank $_FLASHNAME stm32x 0x08000000 0 0 0 $_TARGETNAME
+
+# if srst is not fitted use SYSRESETREQ to
+# perform a soft reset
+cortex_m3 reset_config sysresetreq