mww_phys retired. Replaced by generic mww phys in target.c

5 files changed, 44 insertions, 44 deletions

diff --git a/tcl/board/atmel_at91sam9260-ek.cfg b/tcl/board/atmel_at91sam9260-ek.cfg
index 099d93df..06a54e23 100644
--- a/tcl/board/atmel_at91sam9260-ek.cfg
+++ b/tcl/board/atmel_at91sam9260-ek.cfg
@@ -24,7 +24,7 @@ $_TARGETNAME configure -event reset-start {
         jtag_rclk 5
         halt
         # RSTC_MR : enable user reset, MMU may be enabled... use physical address
-        arm926ejs mww_phys 0xfffffd08 0xa5000501
+        arm926ejs mww phys 0xfffffd08 0xa5000501
 }
 
 $_TARGETNAME configure -event reset-init {
diff --git a/tcl/board/mini2440.cfg b/tcl/board/mini2440.cfg
index 277f61ff..29819501 100644
--- a/tcl/board/mini2440.cfg
+++ b/tcl/board/mini2440.cfg
@@ -177,10 +177,10 @@ proc init_2440 { } {
     # usb clock are off 12mHz xtal
     #-----------------------------------------------
 
-    arm920t mww_phys 0x4C000014 0x00000005 #  Clock Divider control Reg
-    arm920t mww_phys 0x4C000000 0xFFFFFFFF #  LOCKTIME count register
-    arm920t mww_phys 0x4C000008 0x00038022 #  UPPLCON  USB clock config Reg
-    arm920t mww_phys 0x4C000004 0x0007F021 #  MPPLCON  Proc clock config Reg
+    arm920t mww phys 0x4C000014 0x00000005 #  Clock Divider control Reg
+    arm920t mww phys 0x4C000000 0xFFFFFFFF #  LOCKTIME count register
+    arm920t mww phys 0x4C000008 0x00038022 #  UPPLCON  USB clock config Reg
+    arm920t mww phys 0x4C000004 0x0007F021 #  MPPLCON  Proc clock config Reg
 
     #-----------------------------------------------
     # Configure Memory controller
@@ -188,45 +188,45 @@ proc init_2440 { } {
     # DRAM - 64MB - 32 bit bus, uses BANKCON6 BANKCON7
     #-----------------------------------------------
 
-    arm920t mww_phys 0x48000000 0x22111112 #  BWSCON - Bank and Bus Width
-    arm920t mww_phys 0x48000010 0x00001112 #  BANKCON4 - ?
-    arm920t mww_phys 0x4800001c 0x00018009 #  BANKCON6 - DRAM
-    arm920t mww_phys 0x48000020 0x00018009 #  BANKCON7 - DRAM
-    arm920t mww_phys 0x48000024 0x008E04EB #  REFRESH  - DRAM
-    arm920t mww_phys 0x48000028 0x000000B2 #  BANKSIZE - DRAM
-    arm920t mww_phys 0x4800002C 0x00000030 #  MRSRB6 - DRAM
-    arm920t mww_phys 0x48000030 0x00000030 #  MRSRB7 - DRAM
+    arm920t mww phys 0x48000000 0x22111112 #  BWSCON - Bank and Bus Width
+    arm920t mww phys 0x48000010 0x00001112 #  BANKCON4 - ?
+    arm920t mww phys 0x4800001c 0x00018009 #  BANKCON6 - DRAM
+    arm920t mww phys 0x48000020 0x00018009 #  BANKCON7 - DRAM
+    arm920t mww phys 0x48000024 0x008E04EB #  REFRESH  - DRAM
+    arm920t mww phys 0x48000028 0x000000B2 #  BANKSIZE - DRAM
+    arm920t mww phys 0x4800002C 0x00000030 #  MRSRB6 - DRAM
+    arm920t mww phys 0x48000030 0x00000030 #  MRSRB7 - DRAM
 
     #-----------------------------------------------
     # Now port configuration for enables for memory
     # and other stuff.
     #-----------------------------------------------
 
-    arm920t mww_phys 0x56000000	0x007FFFFF #  GPACON
+    arm920t mww phys 0x56000000	0x007FFFFF #  GPACON
 
-    arm920t mww_phys 0x56000010	0x00295559 #  GPBCON
-    arm920t mww_phys 0x56000018	0x000003FF #  GPBUP (PULLUP ENABLE)
-    arm920t mww_phys 0x56000014	0x000007C2 #  GPBDAT
+    arm920t mww phys 0x56000010	0x00295559 #  GPBCON
+    arm920t mww phys 0x56000018	0x000003FF #  GPBUP (PULLUP ENABLE)
+    arm920t mww phys 0x56000014	0x000007C2 #  GPBDAT
 
-    arm920t mww_phys 0x56000020	0xAAAAA6AA #  GPCCON
-    arm920t mww_phys 0x56000028	0x0000FFFF #  GPCUP
-    arm920t mww_phys 0x56000024	0x00000020 #  GPCDAT
+    arm920t mww phys 0x56000020	0xAAAAA6AA #  GPCCON
+    arm920t mww phys 0x56000028	0x0000FFFF #  GPCUP
+    arm920t mww phys 0x56000024	0x00000020 #  GPCDAT
 
-    arm920t mww_phys 0x56000030	0xAAAAAAAA #  GPDCON
-    arm920t mww_phys 0x56000038	0x0000FFFF #  GPDUP
+    arm920t mww phys 0x56000030	0xAAAAAAAA #  GPDCON
+    arm920t mww phys 0x56000038	0x0000FFFF #  GPDUP
 
-    arm920t mww_phys 0x56000040	0xAAAAAAAA #  GPECON
-    arm920t mww_phys 0x56000048	0x0000FFFF #  GPEUP
+    arm920t mww phys 0x56000040	0xAAAAAAAA #  GPECON
+    arm920t mww phys 0x56000048	0x0000FFFF #  GPEUP
 
-    arm920t mww_phys 0x56000050	0x00001555 #  GPFCON
-    arm920t mww_phys 0x56000058	0x0000007F #  GPFUP
-    arm920t mww_phys 0x56000054	0x00000000 #  GPFDAT
+    arm920t mww phys 0x56000050	0x00001555 #  GPFCON
+    arm920t mww phys 0x56000058	0x0000007F #  GPFUP
+    arm920t mww phys 0x56000054	0x00000000 #  GPFDAT
 
-    arm920t mww_phys 0x56000060	0x00150114 #  GPGCON
-    arm920t mww_phys 0x56000068	0x0000007F #  GPGUP
+    arm920t mww phys 0x56000060	0x00150114 #  GPGCON
+    arm920t mww phys 0x56000068	0x0000007F #  GPGUP
 
-    arm920t mww_phys 0x56000070	0x0015AAAA #  GPHCON
-    arm920t mww_phys 0x56000078	0x000003FF #  GPGUP
+    arm920t mww phys 0x56000070	0x0015AAAA #  GPHCON
+    arm920t mww phys 0x56000078	0x000003FF #  GPGUP
 
 }
 
diff --git a/tcl/board/olimex_sam9_l9260.cfg b/tcl/board/olimex_sam9_l9260.cfg
index b5cd10ec..935d7cd5 100644
--- a/tcl/board/olimex_sam9_l9260.cfg
+++ b/tcl/board/olimex_sam9_l9260.cfg
@@ -26,7 +26,7 @@ $_TARGETNAME configure -event reset-start {
 	
 	# RSTC_MR : enable user reset, reset length is 64 slow clock cycles.  MMU may 
 	# be enabled... use physical address.
-	arm926ejs mww_phys 0xfffffd08 0xa5000501
+	arm926ejs mww phys 0xfffffd08 0xa5000501
 }
 
 $_TARGETNAME configure -event reset-init {
diff --git a/tcl/board/unknown_at91sam9260.cfg b/tcl/board/unknown_at91sam9260.cfg
index 017f793f..7286a967 100644
--- a/tcl/board/unknown_at91sam9260.cfg
+++ b/tcl/board/unknown_at91sam9260.cfg
@@ -18,7 +18,7 @@ $_TARGETNAME configure -event reset-start {
         jtag_rclk 3
         halt
 	# RSTC_MR : enable user reset, MMU may be enabled... use physical address
-        arm926ejs mww_phys 0xfffffd08 0xa5000501
+        arm926ejs mww phys 0xfffffd08 0xa5000501
 }
 
 
diff --git a/tcl/target/davinci.cfg b/tcl/target/davinci.cfg
index e1eb48f5..c14c98ea 100644
--- a/tcl/target/davinci.cfg
+++ b/tcl/target/davinci.cfg
@@ -204,34 +204,34 @@ proc davinci_wdog_reset {} {
 	#
 
 	# EMUMGT_CLKSPEED: write FREE bit to run despite emulation halt
-	arm926ejs mww_phys [expr $timer2_phys + 0x28] 0x00004000
+	arm926ejs mww phys [expr $timer2_phys + 0x28] 0x00004000
 
 	#
 	# Part II -- in case watchdog hasn't been set up
 	#
 
 	# TCR: disable, force internal clock source
-	arm926ejs mww_phys [expr $timer2_phys + 0x20] 0
+	arm926ejs mww phys [expr $timer2_phys + 0x20] 0
 
 	# TGCR: reset, force to 64-bit wdog mode, un-reset ("initial" state)
-	arm926ejs mww_phys [expr $timer2_phys + 0x24] 0
-	arm926ejs mww_phys [expr $timer2_phys + 0x24] 0x110b
+	arm926ejs mww phys [expr $timer2_phys + 0x24] 0
+	arm926ejs mww phys [expr $timer2_phys + 0x24] 0x110b
 
 	# clear counter (TIM12, TIM34) and period (PRD12, PRD34) registers
 	# so watchdog triggers ASAP
-	arm926ejs mww_phys [expr $timer2_phys + 0x10] 0
-	arm926ejs mww_phys [expr $timer2_phys + 0x14] 0
-	arm926ejs mww_phys [expr $timer2_phys + 0x18] 0
-	arm926ejs mww_phys [expr $timer2_phys + 0x1c] 0
+	arm926ejs mww phys [expr $timer2_phys + 0x10] 0
+	arm926ejs mww phys [expr $timer2_phys + 0x14] 0
+	arm926ejs mww phys [expr $timer2_phys + 0x18] 0
+	arm926ejs mww phys [expr $timer2_phys + 0x1c] 0
 
 	# WDTCR: put into pre-active state, then active
-	arm926ejs mww_phys [expr $timer2_phys + 0x28] 0xa5c64000
-	arm926ejs mww_phys [expr $timer2_phys + 0x28] 0xda7e4000
+	arm926ejs mww phys [expr $timer2_phys + 0x28] 0xa5c64000
+	arm926ejs mww phys [expr $timer2_phys + 0x28] 0xda7e4000
 
 	#
 	# Part III -- it's ready to rumble
 	#
 
 	# WDTCR: write invalid WDKEY to trigger reset
-	arm926ejs mww_phys [expr $timer2_phys + 0x28] 0x00004000
+	arm926ejs mww phys [expr $timer2_phys + 0x28] 0x00004000
 }