diff options
| -rw-r--r-- | tcl/board/telo.cfg | 2 | ||||
| -rw-r--r-- | tcl/target/c100config.tcl | 4 | ||||
| -rw-r--r-- | tcl/target/c100helper.tcl | 2 | ||||
| -rw-r--r-- | tcl/target/telo.cfg | 61 |
4 files changed, 4 insertions, 65 deletions
diff --git a/tcl/board/telo.cfg b/tcl/board/telo.cfg index a60cb02d..1c0ad762 100644 --- a/tcl/board/telo.cfg +++ b/tcl/board/telo.cfg @@ -58,4 +58,4 @@ set _FLASHNAME $_CHIPNAME.flash flash bank $_FLASHNAME cfi 0x20000000 0x01000000 2 2 $_TARGETNAME # writing data to memory does not work without this -memwrite burst disable
\ No newline at end of file +arm11 memwrite burst disable
\ No newline at end of file diff --git a/tcl/target/c100config.tcl b/tcl/target/c100config.tcl index b08f9098..17a94760 100644 --- a/tcl/target/c100config.tcl +++ b/tcl/target/c100config.tcl @@ -403,9 +403,9 @@ proc flashUBOOT {file} { flash erase_sector 0 0 3 puts "Programming u-boot" putsUART0 "Programming u-boot..." - memwrite burst enable + arm11 memwrite burst enable flash write_image $file $EXP_CS0_BASEADDR - memwrite burst disable + arm11 memwrite burst disable putsUART0 "done.\n" putsUART0 "Rebooting, please wait!\n" reboot diff --git a/tcl/target/c100helper.tcl b/tcl/target/c100helper.tcl index 1fd58b65..477fe5c2 100644 --- a/tcl/target/c100helper.tcl +++ b/tcl/target/c100helper.tcl @@ -325,7 +325,7 @@ proc setupDDR2 {} { if {$tmp == "128M"} { configureDDR2regs_128M } elseif {$tmp == "256M"} { - configureDDR2regs_256B + configureDDR2regs_256M } else { puts "Don't know how to configure DDR2 setup?" } diff --git a/tcl/target/telo.cfg b/tcl/target/telo.cfg deleted file mode 100644 index aa9ff225..00000000 --- a/tcl/target/telo.cfg +++ /dev/null @@ -1,61 +0,0 @@ -source [find target/c100.cfg] -# basic register defintion for C100 -source [find target/c100regs.tcl] -# board-config info -source [find target/c100config.tcl] -# C100 helper functions -source [find target/c100helper.tcl] - - -# Telo board & C100 support trst and srst -# Note that libftd2xx.so tries to assert srst -# which break this script -# use libftdi.so library instead with this script -# make the reset asserted to -# allow RC circuit to discharge for: [ms] -adapter_nsrst_assert_width 100 -jtag_ntrst_assert_width 100 -# don't talk to JTAG after reset for: [ms] -adapter_nsrst_delay 100 -jtag_ntrst_delay 100 -reset_config trst_and_srst separate - - - - -# issue telnet: reset init -# issue gdb: monitor reset init -$_TARGETNAME configure -event reset-init { - adapter_khz 100 - # this will setup Telo board - setupTelo - #turn up the JTAG speed - adapter_khz 3000 - puts "JTAG speed now 3MHz" - puts "type helpC100 to get help on C100" -} - -$_TARGETNAME configure -event reset-deassert-post { - # Force target into ARM state. -# soft_reset_halt # not implemented on ARM11 - puts "Detected SRSRT asserted on C100.CPU" - -} - -$_TARGETNAME configure -event reset-assert-post { - puts "Assering reset" - #sleep 10 -} - -proc power_restore {} { puts "Sensed power restore. No action." } -proc srst_deasserted {} { puts "Sensed nSRST deasserted. No action." } - - -# boots from NOR on CS0: 8 MBytes CFI flash, 16-bit bus -# it's really 16MB but the upper 8mb is controller via gpio -# openocd does not support 'complex reads/writes' to NOR -set _FLASHNAME $_CHIPNAME.flash -flash bank $_FLASHNAME cfi 0x20000000 0x01000000 2 2 $_TARGETNAME - -# writing data to memory does not work without this -memwrite burst disable |