diff options
Diffstat (limited to 'src/tcl/board/digi_connectcore_wi-9c.cfg')
| -rw-r--r-- | src/tcl/board/digi_connectcore_wi-9c.cfg | 127 |
1 files changed, 127 insertions, 0 deletions
diff --git a/src/tcl/board/digi_connectcore_wi-9c.cfg b/src/tcl/board/digi_connectcore_wi-9c.cfg new file mode 100644 index 00000000..93317327 --- /dev/null +++ b/src/tcl/board/digi_connectcore_wi-9c.cfg @@ -0,0 +1,127 @@ +###################################### +# Target: DIGI ConnectCore Wi-9C +###################################### + +reset_config trst_and_srst + +if { [info exists CHIPNAME] } { + set _CHIPNAME $CHIPNAME +} else { + set _CHIPNAME ns9360 +} + +if { [info exists ENDIAN] } { + set _ENDIAN $ENDIAN +} else { + # This config file was defaulting to big endian.. + set _ENDIAN big +} + + +# What's a good fallback frequency for this board if RCLK is +# not available?? +jtag_rclk 1000 + + +if { [info exists CPUTAPID ] } { + set _CPUTAPID $CPUTAPID +} else { + set _CPUTAPID 0xFFFFFFFF +} + +set _TARGETNAME [format "%s.cpu" $_CHIPNAME] +jtag newtap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_CPUTAPID + +jtag_nsrst_delay 200 +jtag_ntrst_delay 0 + + +###################### +# Target configuration +###################### + +target create $_TARGETNAME arm926ejs -endian $_ENDIAN -chain-position $_TARGETNAME -variant arm926ejs +$_TARGETNAME configure -event reset-init { + mww 0x90600104 0x33313333 + mww 0xA0700000 0x00000001 # Enable the memory controller. + mww 0xA0700024 0x00000006 # Set the refresh counter 6 + mww 0xA0700028 0x00000001 # + mww 0xA0700030 0x00000001 # Set the precharge period + mww 0xA0700034 0x00000004 # Active to precharge command period is 16 clock cycles + mww 0xA070003C 0x00000001 # tAPR + mww 0xA0700040 0x00000005 # tDAL + mww 0xA0700044 0x00000001 # tWR + mww 0xA0700048 0x00000006 # tRC 32 clock cycles + mww 0xA070004C 0x00000006 # tRFC 32 clock cycles + mww 0xA0700054 0x00000001 # tRRD + mww 0xA0700058 0x00000001 # tMRD + mww 0xA0700100 0x00004280 # Dynamic Config 0 (cs4) + mww 0xA0700120 0x00004280 # Dynamic Config 1 (cs5) + mww 0xA0700140 0x00004280 # Dynamic Config 2 (cs6) + mww 0xA0700160 0x00004280 # Dynamic Config 3 (cs7) + # + mww 0xA0700104 0x00000203 # CAS latency is 2 at 100 MHz + mww 0xA0700124 0x00000203 # CAS latency is 2 at 100 MHz + mww 0xA0700144 0x00000203 # CAS latency is 2 at 100 MHz + mww 0xA0700164 0x00000203 # CAS latency is 2 at 100 MHz + # + mww 0xA0700020 0x00000103 # issue SDRAM PALL command + # + mww 0xA0700024 0x00000001 # Set the refresh counter to be as small as possible + # + # Add some dummy writes to give the SDRAM time to settle, it needs two + # AHB clock cycles, here we poke in the debugger flag, this lets + # the software know that we are in the debugger + mww 0xA0900000 0x00000002 + mww 0xA0900000 0x00000002 + mww 0xA0900000 0x00000002 + mww 0xA0900000 0x00000002 + mww 0xA0900000 0x00000002 + # + mdw 0xA0900000 + mdw 0xA0900000 + mdw 0xA0900000 + mdw 0xA0900000 + mdw 0xA0900000 + # + mww 0xA0700024 0x00000030 # Set the refresh counter to 30 + mww 0xA0700020 0x00000083 # Issue SDRAM MODE command + # + # Next we perform a read of RAM. + # mw = move word. + mdw 0x00022000 + # mw 0x00022000:P, r3 # 22000 for cas2 latency, 32000 for cas 3 + # + mww 0xA0700020 0x00000003 # issue SDRAM NORMAL command + mww 0xA0700100 0x00084280 # Enable buffer access + mww 0xA0700120 0x00084280 # Enable buffer access + mww 0xA0700140 0x00084280 # Enable buffer access + mww 0xA0700160 0x00084280 # Enable buffer access + + #Set byte lane state (static mem 1)" + mww 0xA0700220, 0x00000082 + #Flash Start + mww 0xA09001F8, 0x50000000 + #Flash Mask Reg + mww 0xA09001FC, 0xFF000001 + mww 0xA0700028, 0x00000001 + + # RAMAddr = 0x00020000 + # RAMSize = 0x00004000 + + # Set the processor mode + reg cpsr 0xd3 +} + +$_TARGETNAME configure -work-area-virt 0 -work-area-phys 0x00000000 -work-area-size 0x1000 -work-area-backup 1 + +##################### +# Flash configuration +##################### + +#M29DW323DB - not working +#flash bank cfi <base> <size> <chip width> <bus width> <target#> +flash bank cfi 0x50000000 0x0400000 2 2 0 + + + |