diff options
Diffstat (limited to 'tcl/board/unknown_at91sam9260.cfg')
| -rw-r--r-- | tcl/board/unknown_at91sam9260.cfg | 96 |
1 files changed, 96 insertions, 0 deletions
diff --git a/tcl/board/unknown_at91sam9260.cfg b/tcl/board/unknown_at91sam9260.cfg new file mode 100644 index 00000000..7763fe49 --- /dev/null +++ b/tcl/board/unknown_at91sam9260.cfg @@ -0,0 +1,96 @@ +# Thanks to Pieter Conradie for this script!
+#
+# Unknown vendor board contains:
+#
+# Atmel AT91SAM9260 : PLLA = 192.512MHz, MCK = 96.256 MHz
+# OSCSEL configured for internal RC oscillator (22 to 42 kHz)
+#
+# 16-bit NOR FLASH : Intel JS28F128P30T85 128MBit
+# 32-bit SDRAM : 2 x Samsung K4S561632H-UC75, 4M x 16Bit x 4 Banks
+##################################################################
+
+# We add to the minimal configuration.
+source [find target/at91sam9260.cfg]
+
+$_TARGETNAME configure -event reset-start {
+ # At reset CPU runs at 22 to 42 kHz.
+ # JTAG Frequency must be 6 times slower.
+ jtag_rclk 3
+ halt
+ # RSTC_MR : enable user reset, MMU may be enabled... use physical address
+ arm926ejs mww_phys 0xfffffd08 0xa5000501
+}
+
+
+$_TARGETNAME configure -event reset-init {
+ mww 0xfffffd44 0x00008000 # WDT_MR : disable watchdog
+
+ mww 0xfffffc20 0x00004001 # CKGR_MOR : enable the main oscillator
+ sleep 20 # wait 20 ms
+ mww 0xfffffc30 0x00000001 # PMC_MCKR : switch to main oscillator
+ sleep 10 # wait 10 ms
+ mww 0xfffffc28 0x205dbf09 # CKGR_PLLAR: Set PLLA Register for 192.512MHz
+ sleep 20 # wait 20 ms
+ mww 0xfffffc30 0x00000101 # PMC_MCKR : Select prescaler (divide by 2)
+ sleep 10 # wait 10 ms
+ mww 0xfffffc30 0x00000102 # PMC_MCKR : Clock from PLLA is selected (96.256 MHz)
+ sleep 10 # wait 10 ms
+
+ # Increase JTAG Speed to 6 MHz if RCLK is not supported
+ jtag_rclk 6000
+
+ arm7_9 dcc_downloads enable # Enable faster DCC downloads
+
+ mww 0xffffec00 0x01020102 # SMC_SETUP0 : Setup SMC for Intel NOR Flash JS28F128P30T85 128MBit
+ mww 0xffffec04 0x09070806 # SMC_PULSE0
+ mww 0xffffec08 0x000d000b # SMC_CYCLE0
+ mww 0xffffec0c 0x00001003 # SMC_MODE0
+
+ flash probe 0 # Identify flash bank 0
+
+ mww 0xfffff870 0xffff0000 # PIO_ASR : Select peripheral function for D15..D31
+ mww 0xfffff804 0xffff0000 # PIO_PDR : Disable PIO function for D15..D31
+ mww 0xfffff860 0xffff0000 # PIO_PUDR : Disable D15..D31 pull-ups
+
+ mww 0xffffef1c 0x00010102 # EBI_CSA : Assign EBI Chip Select 1 to SDRAM
+ # VDDIOMSEL set for +3V3 memory
+ # Disable D0..D15 pull-ups
+
+ mww 0xffffea08 0x85227259 # SDRAMC_CR : Configure SDRAM (2 x Samsung K4S561632H-UC75 : 4M x 16Bit x 4 Banks)
+
+ mww 0xffffea00 0x1 # SDRAMC_MR : issue a NOP command
+ mww 0x20000000 0
+ mww 0xffffea00 0x2 # SDRAMC_MR : issue an 'All Banks Precharge' command
+ mww 0x20000000 0
+ mww 0xffffea00 0x4 # SDRAMC_MR : issue 8 x 'Auto-Refresh' Command
+ mww 0x20000000 0
+ mww 0xffffea00 0x4
+ mww 0x20000000 0
+ mww 0xffffea00 0x4
+ mww 0x20000000 0
+ mww 0xffffea00 0x4
+ mww 0x20000000 0
+ mww 0xffffea00 0x4
+ mww 0x20000000 0
+ mww 0xffffea00 0x4
+ mww 0x20000000 0
+ mww 0xffffea00 0x4
+ mww 0x20000000 0
+ mww 0xffffea00 0x4
+ mww 0x20000000 0
+ mww 0xffffea00 0x3 # SDRAMC_MR : issue a 'Load Mode Register' command
+ mww 0x20000000 0
+ mww 0xffffea00 0x0 # SDRAMC_MR : normal mode
+ mww 0x20000000 0
+ mww 0xffffea04 0x2a2 # SDRAMC_TR : Set refresh timer count to 7us
+}
+
+
+#####################
+# Flash configuration
+#####################
+
+#flash bank cfi <base> <size> <chip width> <bus width> <target#>
+flash bank cfi 0x10000000 0x01000000 2 2 0
+
+
|