moved out stuff that wasn't already moved from openocd.pdf to the target library.

git-svn-id: svn://svn.berlios.de/openocd/trunk@576 b42882b7-edfa-0310-969c-e2dbd0fdcd60

13 files changed, 189 insertions, 652 deletions

diff --git a/doc/openocd.texi b/doc/openocd.texi
index 834edee2..60142be7 100644
--- a/doc/openocd.texi
+++ b/doc/openocd.texi
@@ -47,6 +47,7 @@ This manual documents edition @value{EDITION} of the Open On-Chip Debugger
 * Building::          Building Openocd
 * Running::           Running Openocd
 * Configuration::     Openocd Configuration.
+* Target library::    Target library
 * Commands::          Openocd Commands
 * Sample Scripts::    Sample Target Scripts
 * GDB and Openocd::   Using GDB and Openocd
@@ -235,7 +236,9 @@ chain, the targets that should be debugged, and connected flashes.
 @itemize @bullet
 @item @b{init} This command terminates the configuration stage and enters the normal
 command mode. This can be useful to add commands to the startup scripts and commands
-such as resetting the target, programming flash, etc.
+such as resetting the target, programming flash, etc. To reset the CPU upon startup,
+add "init" and "reset" at the end of the config script or at the end of the
+openocd command line using the -c option.
 @cindex init
 @item @b{telnet_port} <@var{number}>
 @cindex telnet_port
@@ -263,8 +266,9 @@ Default behaviour is <@var{disable}>
 @item @b{daemon_startup} <@var{mode}>
 @cindex daemon_startup
 @option{mode} can either @option{attach} or @option{reset}
-Tells the OpenOCD whether it should reset the target when the daemon is launched, or
-if it should just attach to the target. 
+This is equivalent to adding "init" and "reset" to the end of the config script.
+
+It is availble as a command mainly for backwards compatibility.
 @end itemize
 
 @section JTAG interface configuration
@@ -1219,7 +1223,7 @@ Enable/disable target debugmsgs requests. debugmsgs enable messages to be sent t
 @chapter Sample Scripts
 @cindex scripts
 
-This page will collect some script examples for different CPUs.
+This page shows how to use the target library.
 
 The configuration script can be divided in the following section:
 @itemize @bullet
@@ -1230,657 +1234,16 @@ The configuration script can be divided in the following section:
 @item flash configuration 
 @end itemize
 
-Detailed information about each section can be found at OpenOCD configuration 
-
-@section OMAP5912 Flash Debug
-@cindex OMAP5912 Flash Debug
-The following two scripts were used with a wiggler PP and and a TI OMAP5912
-dual core processor - (@uref{http://www.ti.com}), on a OMAP5912 OSK board
-- (@uref{http://www.spectrumdigital.com}).
-@subsection Openocd config
-@smallexample
-#daemon configuration
-telnet_port 4444
-gdb_port 3333
-
-#interface
-interface parport
-parport_port 0x378
-parport_cable wiggler
-jtag_speed 0
-
-#use combined on interfaces or targets that can't set TRST/SRST separately
-reset_config trst_and_srst
-
-#jtag scan chain
-#format L IRC IRCM IDCODE (Length, IR Capture, IR Capture Mask, IDCODE)
-jtag_device 38 0x0 0x0 0x0
-jtag_device 4  0x1 0x0 0xe
-jtag_device 8  0x0 0x0 0x0
-
-#target configuration
-daemon_startup reset
-
-#target <type> <endianness> <reset mode> <chainpos> <variant>
-target arm926ejs little run_and_init 1 arm926ejs
-target_script 0 reset omap5912_osk.init
-run_and_halt_time 0 30
-
-# omap5912 lcd frame buffer as working area
-working_area 0 0x20000000 0x3e800 nobackup
-
-#flash bank <driver> <base> <size> <chip_width> <bus_width>
-flash bank cfi 0x00000000 0x1000000 2 2 0
-@end smallexample
-
-@subsection Openocd init
-@smallexample
-#
-# halt target
-#
-poll
-sleep 1
-halt
-wait_halt
-#
-# disable wdt
-#
-mww 0xfffec808 0x000000f5
-mww 0xfffec808 0x000000a0
-
-mww 0xfffeb048 0x0000aaaa
-sleep 500
-mww 0xfffeb048 0x00005555
-sleep 500
-#
-# detect flash
-#
-flash probe 0
-
-@end smallexample
-
-@section STR71x Script
-@cindex STR71x Script
-The following script was used with an Amontec JTAGkey and a STR710 / STR711 CPU:
-@smallexample
-#daemon configuration
-telnet_port 4444
-gdb_port 3333
- 
-#interface
-interface ft2232
-ft2232_device_desc "Amontec JTAGkey A"
-ft2232_layout jtagkey
-ft2232_vid_pid 0x0403 0xcff8
-jtag_speed 0
- 
-#use combined on interfaces or targets that can't set TRST/SRST separately
-reset_config trst_and_srst srst_pulls_trst
- 
-#jtag scan chain
-#format L IRC IRCM IDCODE (Length, IR Capture, IR Capture Mask, IDCODE)
-jtag_device 4 0x1 0xf 0xe
- 
-#target configuration
-daemon_startup reset
- 
-#target <type> <startup mode>
-#target arm7tdmi <endianness> <reset mode> <chainpos> <variant>
-target arm7tdmi little run_and_halt 0 arm7tdmi
-run_and_halt_time 0 30
-
-working_area 0 0x2000C000 0x4000 nobackup
- 
-#flash bank <driver> <base> <size> <chip_width> <bus_width>
-flash bank str7x 0x40000000 0x00040000 0 0 0 STR71x
-@end smallexample
-
-@section STR750 Script
-@cindex STR750 Script
-The following script was used with an Amontec JTAGkey and a STR750 CPU:
-@smallexample
-#daemon configuration
-telnet_port 4444
-gdb_port 3333
- 
-#interface
-interface ft2232
-ft2232_device_desc "Amontec JTAGkey A"
-ft2232_layout jtagkey
-ft2232_vid_pid 0x0403 0xcff8
-jtag_speed 19
- 
-#use combined on interfaces or targets that can't set TRST/SRST separately
-#reset_config trst_and_srst srst_pulls_trst
-reset_config trst_and_srst srst_pulls_trst
-
-#jtag scan chain
-#format L IRC IRCM IDCODE (Length, IR Capture, IR Capture Mask, IDCODE)
-jtag_device 4 0x1 0xf 0xe
-
-#jtag nTRST and nSRST delay
-jtag_nsrst_delay 500
-jtag_ntrst_delay 500
- 
-#target configuration
-daemon_startup reset
- 
-#target <type> <startup mode>
-#target arm7tdmi <reset mode> <chainpos> <endianness> <variant>
-target arm7tdmi little run_and_halt 0 arm7tdmi
-run_and_halt_time 0 30
- 
-working_area 0 0x40000000 0x4000 nobackup
- 
-#flash bank <driver> <base> <size> <chip_width> <bus_width>
-flash bank str7x 0x20000000 0x000040000 0 0 0 STR75x
-@end smallexample
-
-@section STR912 Script
-@cindex STR912 Script
-The following script was used with an Amontec JTAGkey and a STR912 CPU:
-@smallexample
-#daemon configuration
-telnet_port 4444
-gdb_port 3333
- 
-#interface
-interface ft2232
-ft2232_device_desc "Amontec JTAGkey A"
-ft2232_layout jtagkey
-jtag_speed 1
- 
-#use combined on interfaces or targets that can't set TRST/SRST separately
-reset_config trst_and_srst
- 
-#jtag scan chain
-#format L IRC IRCM IDCODE (Length, IR Capture, IR Capture Mask, IDCODE)
-jtag_device 8 0x1 0x1 0xfe
-jtag_device 4 0x1 0xf 0xe
-jtag_device 5 0x1 0x1 0x1e
- 
-#target configuration
-daemon_startup reset
- 
-#target <type> <startup mode>
-#target arm966e <endianness> <reset mode> <chainpos> <variant>
-target arm966e little reset_halt 1 arm966e
-run_and_halt_time 0 30
- 
-working_area 0 0x50000000 16384 nobackup
- 
-#flash bank <driver> <base> <size> <chip_width> <bus_width>
-flash bank str9x 0x00000000 0x00080000 0 0 0
-@end smallexample
-
-@section STR912 comstick
-@cindex STR912 comstick Script
-The following script was used with a Hitex STR9 Comstick:
-@smallexample
-#daemon configuration
-telnet_port 4444
-gdb_port 3333
- 
-#interface
-interface ft2232
-ft2232_device_desc "STR9-comStick A"
-ft2232_layout comstick
-jtag_speed 1
-
-jtag_nsrst_delay 100
-jtag_ntrst_delay 100
+Detailed information about each section can be found at OpenOCD configuration. 
 
-#use combined on interfaces or targets that can't set TRST/SRST separately
-reset_config trst_and_srst
- 
-#jtag scan chain
-#format L IRC IRCM IDCODE (Length, IR Capture, IR Capture Mask, IDCODE)
-jtag_device 8 0x1 0x1 0xfe
-jtag_device 4 0x1 0xf 0xe
-jtag_device 5 0x1 0x1 0x1e
- 
-#target configuration
-daemon_startup reset
- 
-#target <type> <startup mode>
-#target arm966e <endianness> <reset mode> <chainpos> <variant>
-target arm966e little reset_halt 1 arm966e
-run_and_halt_time 0 30
- 
-working_area 0 0x50000000 16384 nobackup
- 
-#flash bank <driver> <base> <size> <chip_width> <bus_width>
-flash bank str9x 0x00000000 0x00080000 0 0 0
-@end smallexample
-
-@section STM32x Script
-@cindex STM32x Script
-The following script was used with an Amontec JTAGkey and a STM32x CPU:
+@section AT91R40008 example
+@cindex AT91R40008 example
+To start OpenOCD with a target script for the AT91R40008 CPU and reset
+the CPU upon startup of the OpenOCD daemon.
 @smallexample
-#daemon configuration
-telnet_port 4444
-gdb_port 3333
- 
-#interface
-interface ft2232
-ft2232_device_desc "Amontec JTAGkey A"
-ft2232_layout jtagkey
-jtag_speed 10
-
-jtag_nsrst_delay 100
-jtag_ntrst_delay 100
-
-#use combined on interfaces or targets that can't set TRST/SRST separately
-reset_config trst_and_srst
- 
-#jtag scan chain
-#format L IRC IRCM IDCODE (Length, IR Capture, IR Capture Mask, IDCODE)
-jtag_device 4 0x1 0xf 0xe
-jtag_device 5 0x1 0x1 0x1e
- 
-#target configuration
-daemon_startup reset
- 
-#target <type> <startup mode>
-#target cortex_m3 <endianness> <reset mode> <chainpos> <variant>
-target cortex_m3 little run_and_halt 0
-run_and_halt_time 0 30
- 
-working_area 0 0x20000000 16384 nobackup
- 
-#flash bank <driver> <base> <size> <chip_width> <bus_width>
-flash bank stm32x 0x08000000 0x00020000 0 0 0
-@end smallexample
-
-@section STM32x Performance Stick
-@cindex STM32x Performance Stick Script
-The following script was used with the Hitex STM32 Performance Stick
-@smallexample
-#daemon configuration
-telnet_port 4444
-gdb_port 3333
- 
-#interface
-interface ft2232
-ft2232_device_desc "STM32-PerformanceStick A"
-ft2232_layout stm32stick
-jtag_speed 10
-
-jtag_nsrst_delay 100
-jtag_ntrst_delay 100
-
-#use combined on interfaces or targets that can't set TRST/SRST separately
-reset_config trst_and_srst
- 
-#jtag scan chain
-#format L IRC IRCM IDCODE (Length, IR Capture, IR Capture Mask, IDCODE)
-jtag_device 4 0x1 0xf 0xe
-jtag_device 5 0x1 0x1 0x1e
-jtag_device 4 0x1 0xf 0xe
- 
-#target configuration
-daemon_startup reset
- 
-#target <type> <startup mode>
-#target cortex_m3 <endianness> <reset mode> <chainpos> <variant>
-target cortex_m3 little run_and_halt 0
-run_and_halt_time 0 30
- 
-working_area 0 0x20000000 16384 nobackup
- 
-#flash bank <driver> <base> <size> <chip_width> <bus_width>
-flash bank stm32x 0x08000000 0x00020000 0 0 0
+openocd -f interface/parport.cfg -f target/at91r40008.cfg -c init -c reset 
 @end smallexample
 
-@section LPC2129 Script
-@cindex LPC2129 Script
-The following script was used with an wiggler PP and a LPC-2129 CPU:
-@smallexample
-#daemon configuration
-telnet_port 4444
-gdb_port 3333
- 
-#interface
-interface parport
-parport_port 0x378
-parport_cable wiggler
-jtag_speed 0
- 
-#use combined on interfaces or targets that can't set TRST/SRST separately
-reset_config trst_and_srst srst_pulls_trst
- 
-#jtag scan chain
-#format L IRC IRCM IDCODE (Length, IR Capture, IR Capture Mask, IDCODE)
-jtag_device 4 0x1 0xf 0xe
- 
-#target configuration
-daemon_startup reset
- 
-#target <type> <startup mode>
-#target arm7tdmi <endianness> <reset mode> <chainpos> <variant>
-target arm7tdmi little run_and_halt 0 arm7tdmi-s_r4
-run_and_halt_time 0 30
- 
-working_area 0 0x40000000 0x4000 nobackup
- 
-#flash bank <driver> <base> <size> <chip_width> <bus_width>
-flash bank lpc2000 0x0 0x40000 0 0 0 lpc2000_v1 14765 calc_checksum
-@end smallexample
-
-@section  LPC2148 Script
-@cindex  LPC2148 Script
-The following script was used with an Amontec JTAGkey and a LPC2148 CPU:
-@smallexample
-#daemon configuration
-telnet_port 4444
-gdb_port 3333
- 
-#interface
-interface ft2232
-ft2232_device_desc "Amontec JTAGkey A"
-ft2232_layout jtagkey
-ft2232_vid_pid 0x0403 0xcff8
-jtag_speed 3
- 
-#use combined on interfaces or targets that can't set TRST/SRST separately
-reset_config trst_and_srst srst_pulls_trst
- 
-#jtag scan chain
-#format L IRC IRCM IDCODE (Length, IR Capture, IR Capture Mask, IDCODE)
-jtag_device 4 0x1 0xf 0xe
- 
-#target configuration
-daemon_startup reset
- 
-#target <type> <startup mode>
-#target arm7tdmi <endianness> <reset mode> <chainpos> <variant>
-target arm7tdmi little run_and_halt 0 arm7tdmi-s_r4
-run_and_halt_time 0 30
- 
-working_area 0 0x40000000 0x8000 nobackup
- 
-#flash configuration
-flash bank lpc2000 0x0 0x7d000 0 0 0 lpc2000_v1 14765 calc_checksum
-@end smallexample
-
-@section  LPC2294 Script
-@cindex  LPC2294 Script
-The following script was used with an Amontec JTAGkey and a LPC2294 CPU:
-@smallexample
-#daemon configuration
-telnet_port 4444
-gdb_port 3333
- 
-#interface
-interface ft2232
-ft2232_device_desc "Amontec JTAGkey A"
-ft2232_layout jtagkey
-ft2232_vid_pid 0x0403 0xcff8
-jtag_speed 3
- 
-#use combined on interfaces or targets that can't set TRST/SRST separately
-reset_config trst_and_srst srst_pulls_trst
- 
-#jtag scan chain
-#format L IRC IRCM IDCODE (Length, IR Capture, IR Capture Mask, IDCODE)
-jtag_device 4 0x1 0xf 0xe
- 
-#target configuration
-daemon_startup reset
- 
-#target <type> <startup mode>
-#target arm7tdmi <endianness> <reset mode> <chainpos> <variant>
-target arm7tdmi little run_and_halt 0 arm7tdmi-s_r4
-run_and_halt_time 0 30
- 
-working_area 0 0x40000000 0x4000 nobackup
- 
-#flash configuration
-flash bank lpc2000 0x0 0x40000 0 0 0 lpc2000_v1 14765 calc_checksum
-@end smallexample
-
-@section AT91R40008 Script
-@cindex AT91R40008 Script
-The following script was used with an Amontec JTAGkey and a AT91R40008 CPU:
-@smallexample
-#daemon configuration
-telnet_port 4444
-gdb_port 3333
- 
-#interface
-interface ft2232
-ft2232_device_desc "Amontec JTAGkey A"
-ft2232_layout jtagkey
-ft2232_vid_pid 0x0403 0xcff8
-jtag_speed 0
-jtag_nsrst_delay 200
-jtag_ntrst_delay 200
- 
-#use combined on interfaces or targets that can't set TRST/SRST separately
-reset_config srst_only srst_pulls_trst
- 
-#jtag scan chain
-#format L IRC IRCM IDCODE (Length, IR Capture, IR Capture Mask, IDCODE)
-jtag_device 4 0x1 0xf 0xe
- 
-#target configuration
-daemon_startup reset
- 
-#target <type> <startup mode>
-#target arm7tdmi <endianness> <reset mode> <chainpos> <variant>
-target arm7tdmi little run_and_halt 0 arm7tdmi
-run_and_halt_time 0 30
-@end smallexample
-
-@section AT91SAM7s Script
-@cindex AT91SAM7s Script
-The following script was used with an Olimex ARM-JTAG-OCD and a AT91SAM7S64 CPU:
-@smallexample
-#daemon configuration
-telnet_port 4444
-gdb_port 3333
- 
-#interface
-interface ft2232
-ft2232_device_desc "Olimex OpenOCD JTAG A"
-ft2232_layout olimex-jtag
-ft2232_vid_pid 0x15BA 0x0003
-jtag_speed 0
-jtag_nsrst_delay 200
-jtag_ntrst_delay 200
- 
-#use combined on interfaces or targets that can't set TRST/SRST separately
-reset_config srst_only srst_pulls_trst
- 
-#jtag scan chain
-#format L IRC IRCM IDCODE (Length, IR Capture, IR Capture Mask, IDCODE)
-jtag_device 4 0x1 0xf 0xe
- 
-#target configuration
-daemon_startup reset
- 
-#target <type> <startup mode>
-#target arm7tdmi <endianness> <reset mode> <chainpos> <variant>
-target arm7tdmi little run_and_halt 0 arm7tdmi
-run_and_halt_time 0 30
- 
-# flash-options AT91
-working_area 0 0x00200000 0x4000 nobackup
-flash bank at91sam7 0 0 0 0 0
- 
-# Information: 
-# erase command (telnet-interface) for complete flash:
-# flash erase <num> 0 numlockbits-1 (can be seen from output of flash info 0)
-# SAM7S64 with 16 lockbits and bank 0: flash erase 0 0 15
-# set/clear NVM-Bits:
-# at91sam7 gpnvm <num> <bit> <set|clear>
-# disable locking from SAM-BA:
-# flash protect 0 0 1 off
-@end smallexample
-
-@section XSCALE IXP42x Script
-@cindex XSCALE IXP42x Script
-The following script was used with an Amontec JTAGkey-Tiny and a xscale ixp42x CPU:
-@smallexample
-#daemon configuration
-telnet_port 4444
-gdb_port 3333
-
-#interface
-interface ft2232
-ft2232_device_desc "Amontec JTAGkey A"
-ft2232_layout jtagkey
-ft2232_vid_pid 0x0403 0xcff8
-jtag_speed 0
-jtag_nsrst_delay 200
-jtag_ntrst_delay 200
- 
-#use combined on interfaces or targets that can't set TRST/SRST separately
-reset_config srst_only srst_pulls_trst
- 
-#jtag scan chain
-#format L IRC IRCM IDCODE (Length, IR Capture, IR Capture Mask, IDCODE)
-jtag_device 7 0x1 0x7f 0x7e
- 
-#target configuration
-daemon_startup reset
- 
-#target <type> <startup mode>
-#target arm7tdmi <reset mode> <chainpos> <endianness> <variant>
-target xscale big run_and_halt 0 IXP42x
-run_and_halt_time 0 30
-@end smallexample
-
-@section Cirrus Logic EP9301 Script
-@cindex Cirrus Logic EP9301 Script
-The following script was used with FT2232 based JTAG interfaces and a
-Cirrus Logic EP9301 processor on an Olimex CS-E9301 board.
-@smallexample
-#daemon configuration
-telnet_port 4444
-gdb_port 3333
- 
-#interface
-interface ft2232
-
-#Olimex ARM-USB-OCD
-#ft2232_device_desc "Olimex OpenOCD JTAG"
-#ft2232_layout olimex-jtag
-#ft2232_vid_pid 0x15ba 0x0003
- 
-#Amontec JTAGkey (and JTAGkey-Tiny)
-#Serial is only necessary if more than one JTAGkey is connected
-ft2232_device_desc "Amontec JTAGkey A"
-#ft2232_serial AMTJKV31
-#ft2232_serial T1P3S2W8
-ft2232_layout jtagkey
-ft2232_vid_pid 0x0403 0xcff8
- 
-#wiggler/parallel port interface
-#interface parport
-#parport_port 0x378
-#parport_cable wiggler
-#jtag_speed 0
-jtag_speed 1
-reset_config trst_and_srst
- 
-#jtag scan chain
-#format L IRC IRCM IDCODE (Length, IR Capture, IR Capture Mask, IDCODE)
-jtag_device 4 0x1 0xf 0xe
- 
-jtag_nsrst_delay 100
-jtag_ntrst_delay 100
- 
-#target configuration
-daemon_startup attach
- 
-#target <type> <endianess> <reset mode>
-target arm920t little reset_halt 0
-working_area 0 0x80014000 0x1000 backup
- 
-#flash configuration
-#flash bank <driver> <base> <size> <chip_width> <bus_width> [driver_options ...]
-flash bank cfi 0x60000000 0x1000000 2 2 0
-@end smallexample
-
-@section Hilscher netX 100 / 500 Script
-@cindex Hilscher netX 100 / 500 Script
-The following script was used with an Amontec JTAGkey and a Hilscher
-netX 500 CPU:
-@smallexample
-#daemon configuration
-telnet_port 4444
-gdb_port 3333
-
-#interface
-interface ft2232
-ft2232_device_desc "Amontec JTAGkey A"
-ft2232_layout jtagkey
-ft2232_vid_pid 0x0403 0xcff8
-jtag_speed 5
-
-#use combined on interfaces or targets that can't set TRST/SRST separately
-reset_config trst_and_srst
-
-#jtag scan chain
-#format L IRC IRCM IDCODE (Length, IR Capture, IR Capture Mask, IDCODE)
-jtag_device 4 0x1 0xf 0xe
-
-jtag_nsrst_delay 100
-jtag_ntrst_delay 100
-
-#target configuration
-daemon_startup reset
-
-#target <type> <endianness> <startup mode> <chainpos> <variant>
-target arm926ejs little run_and_halt 0 arm926ejs
-run_and_halt_time 0 500
-@end smallexample
-
-@section Marvell/Intel PXA270 Script
-@cindex Marvell/Intel PXA270 Script
-@smallexample
-# config for Intel PXA270
-# not, as of 2007-06-22, openocd only works with the
-# libftd2xx library from ftdi.  libftdi does not work.
-
-telnet_port	3333
-gdb_port	4444
-
-interface ft2232
-ft2232_layout olimex-jtag
-ft2232_vid_pid 0x15BA 0x0003
-ft2232_device_desc "Olimex OpenOCD JTAG"
-jtag_speed 0
-# set jtag_nsrst_delay to the delay introduced by your reset circuit
-# the rest of the needed delays are built into the openocd program
-jtag_nsrst_delay 260
-# set the jtag_ntrst_delay to the delay introduced by a reset circuit
-# the rest of the needed delays are built into the openocd program
-jtag_ntrst_delay 0
-
-#use combined on interfaces or targets that can't set TRST/SRST separately
-reset_config trst_and_srst separate
-
-#jtag scan chain
-#format L IRC IRCM IDCODE (Length, IR Capture, IR Capture Mask, IDCODE)
-jtag_device 7 0x1 0x7f 0x7e
-
-#target configuration
-daemon_startup reset
-
-target xscale little reset_halt 0 pxa27x
-
-# maps to PXA internal RAM.  If you are using a PXA255
-# you must initialize SDRAM or leave this option off
-working_area 0 0x5c000000 0x10000 nobackup
-
-run_and_halt_time 0 30
-
-#flash bank <driver> <base> <size> <chip_width> <bus_width>
-# works for P30 flash
-flash bank cfi 0x00000000 0x1000000 2 4 0
-@end smallexample
 
 @node GDB and Openocd
 @chapter GDB and Openocd
diff --git a/src/target/Makefile.am b/src/target/Makefile.am
index 2de8cf00..d975d6fc 100644
--- a/src/target/Makefile.am
+++ b/src/target/Makefile.am
@@ -24,4 +24,8 @@ nobase_dist_pkglib_DATA = xscale/debug_handler.bin event/at91eb40a_reset.script
 	target/sam7x256.cfg target/str710.cfg target/str912.cfg target/nslu2.cfg target/pxa255_sst.cfg \
 	target/pxa255.cfg  target/zy1000.cfg event/zy1000_reset.script event/at91sam9260_reset.script target/at91sam9260.cfg \
 	target/wi-9c.cfg event/wi-9c_reset.script event/pxa255_reset.script target/stm32.cfg  target/xba_revA3.cfg event/xba_revA3.script \
-	ecos/at91eb40a.elf target/lm3s6965.cfg interface/parport.cfg
+	ecos/at91eb40a.elf target/lm3s6965.cfg interface/parport.cfg \
+	event/omap5912_reset.script interface/amontec-tiny.cfg interface/str9-comstick.cfg \
+	target/epc9301.cfg target/ipx42x.cfg target/lpc2129.cfg target/netx500.cfg \
+	target/omap5912.cfg target/pxa270.cfg target/str750.cfg target/str9comstick.cfg
+  
diff --git a/src/target/event/omap5912_reset.script b/src/target/event/omap5912_reset.script
new file mode 100644
index 00000000..9d452018
--- /dev/null
+++ b/src/target/event/omap5912_reset.script
@@ -0,0 +1,21 @@
+#

+# halt target

+#

+poll

+sleep 1

+halt

+wait_halt

+#

+# disable wdt

+#

+mww 0xfffec808 0x000000f5

+mww 0xfffec808 0x000000a0

+

+mww 0xfffeb048 0x0000aaaa

+sleep 500

+mww 0xfffeb048 0x00005555

+sleep 500

+#

+# detect flash

+#

+flash probe 0

diff --git a/src/target/interface/amontec-tiny.cfg b/src/target/interface/amontec-tiny.cfg
new file mode 100644
index 00000000..aaa1cde2
--- /dev/null
+++ b/src/target/interface/amontec-tiny.cfg
@@ -0,0 +1,8 @@
+#interface

+interface ft2232

+ft2232_device_desc "Amontec JTAGkey A"

+ft2232_layout jtagkey

+ft2232_vid_pid 0x0403 0xcff8

+jtag_speed 0

+jtag_nsrst_delay 200

+jtag_ntrst_delay 200

diff --git a/src/target/interface/str9-comstick.cfg b/src/target/interface/str9-comstick.cfg
new file mode 100644
index 00000000..afece3ce
--- /dev/null
+++ b/src/target/interface/str9-comstick.cfg
@@ -0,0 +1,3 @@
+interface ft2232

+ft2232_device_desc "STR9-comStick A"

+ft2232_layout comstick

diff --git a/src/target/target/epc9301.cfg b/src/target/target/epc9301.cfg
new file mode 100644
index 00000000..f3b5eb88
--- /dev/null
+++ b/src/target/target/epc9301.cfg
@@ -0,0 +1,12 @@
+# Cirrus Logic EP9301 processor on an Olimex CS-E9301 board.

+jtag_device 4 0x1 0xf 0xe

+jtag_nsrst_delay 100

+jtag_ntrst_delay 100

+#target configuration

+daemon_startup attach

+#target <type> <endianess> <reset mode>

+target arm920t little reset_halt 0

+working_area 0 0x80014000 0x1000 backup

+#flash configuration

+#flash bank <driver> <base> <size> <chip_width> <bus_width> [driver_options ...]

+flash bank cfi 0x60000000 0x1000000 2 2 0

diff --git a/src/target/target/ipx42x.cfg b/src/target/target/ipx42x.cfg
new file mode 100644
index 00000000..397985d2
--- /dev/null
+++ b/src/target/target/ipx42x.cfg
@@ -0,0 +1,13 @@
+#xscale ixp42x CPU

+

+#use combined on interfaces or targets that can’t set TRST/SRST separately

+reset_config srst_only srst_pulls_trst

+#jtag scan chain

+#format L IRC IRCM IDCODE (Length, IR Capture, IR Capture Mask, IDCODE)

+jtag_device 7 0x1 0x7f 0x7e

+#target configuration

+daemon_startup reset

+#target <type> <startup mode>

+#target arm7tdmi <reset mode> <chainpos> <endianness> <variant>

+target xscale big run_and_halt 0 IXP42x

+run_and_halt_time 0 30

diff --git a/src/target/target/lpc2129.cfg b/src/target/target/lpc2129.cfg
new file mode 100644
index 00000000..908b2512
--- /dev/null
+++ b/src/target/target/lpc2129.cfg
@@ -0,0 +1,15 @@
+#LPC-2129 CPU

+#use combined on interfaces or targets that can’t set TRST/SRST separately

+reset_config trst_and_srst srst_pulls_trst

+#jtag scan chain

+#format L IRC IRCM IDCODE (Length, IR Capture, IR Capture Mask, IDCODE)

+jtag_device 4 0x1 0xf 0xe

+#target configuration

+daemon_startup reset

+#target <type> <startup mode>

+#target arm7tdmi <endianness> <reset mode> <chainpos> <variant>

+target arm7tdmi little run_and_halt 0 arm7tdmi-s_r4

+run_and_halt_time 0 30

+working_area 0 0x40000000 0x4000 nobackup

+#flash bank <driver> <base> <size> <chip_width> <bus_width>

+flash bank lpc2000 0x0 0x40000 0 0 0 lpc2000_v1 14765 calc_checksum

diff --git a/src/target/target/netx500.cfg b/src/target/target/netx500.cfg
new file mode 100644
index 00000000..9bb6bed2
--- /dev/null
+++ b/src/target/target/netx500.cfg
@@ -0,0 +1,13 @@
+#Hilscher netX 500 CPU

+#use combined on interfaces or targets that can’t set TRST/SRST separately

+reset_config trst_and_srst

+#jtag scan chain

+#format L IRC IRCM IDCODE (Length, IR Capture, IR Capture Mask, IDCODE)

+jtag_device 4 0x1 0xf 0xe

+jtag_nsrst_delay 100

+jtag_ntrst_delay 100

+#target configuration

+daemon_startup reset

+#target <type> <endianness> <startup mode> <chainpos> <variant>

+target arm926ejs little run_and_halt 0 arm926ejs

+run_and_halt_time 0 500

diff --git a/src/target/target/omap5912.cfg b/src/target/target/omap5912.cfg
new file mode 100644
index 00000000..2c471a7a
--- /dev/null
+++ b/src/target/target/omap5912.cfg
@@ -0,0 +1,25 @@
+#TI OMAP5912 dual core processor - http://www.ti.com 

+#on a OMAP5912 OSK board http://www.spectrumdigital.com.

+

+#use combined on interfaces or targets that can't set TRST/SRST separately

+reset_config trst_and_srst

+

+#jtag scan chain

+#format L IRC IRCM IDCODE (Length, IR Capture, IR Capture Mask, IDCODE)

+jtag_device 38 0x0 0x0 0x0

+jtag_device 4  0x1 0x0 0xe

+jtag_device 8  0x0 0x0 0x0

+

+#target configuration

+daemon_startup reset

+

+#target <type> <endianness> <reset mode> <chainpos> <variant>

+target arm926ejs little run_and_init 1 arm926ejs

+target_script 0 reset event/omap5912_reset.script

+run_and_halt_time 0 30

+

+# omap5912 lcd frame buffer as working area

+working_area 0 0x20000000 0x3e800 nobackup

+

+#flash bank <driver> <base> <size> <chip_width> <bus_width>

+flash bank cfi 0x00000000 0x1000000 2 2 0

diff --git a/src/target/target/pxa270.cfg b/src/target/target/pxa270.cfg
new file mode 100644
index 00000000..5946e757
--- /dev/null
+++ b/src/target/target/pxa270.cfg
@@ -0,0 +1,22 @@
+#Marvell/Intel PXA270 Script

+# set jtag_nsrst_delay to the delay introduced by your reset circuit

+# the rest of the needed delays are built into the openocd program

+jtag_nsrst_delay 260

+# set the jtag_ntrst_delay to the delay introduced by a reset circuit

+# the rest of the needed delays are built into the openocd program

+jtag_ntrst_delay 0

+#use combined on interfaces or targets that can’t set TRST/SRST separately

+reset_config trst_and_srst separate

+#jtag scan chain

+#format L IRC IRCM IDCODE (Length, IR Capture, IR Capture Mask, IDCODE)

+jtag_device 7 0x1 0x7f 0x7e

+#target configuration

+daemon_startup reset

+target xscale little reset_halt 0 pxa27x

+# maps to PXA internal RAM. If you are using a PXA255

+# you must initialize SDRAM or leave this option off

+working_area 0 0x5c000000 0x10000 nobackup

+run_and_halt_time 0 30

+#flash bank <driver> <base> <size> <chip_width> <bus_width>

+# works for P30 flash

+flash bank cfi 0x00000000 0x1000000 2 4 0

diff --git a/src/target/target/str750.cfg b/src/target/target/str750.cfg
new file mode 100644
index 00000000..6e7c2180
--- /dev/null
+++ b/src/target/target/str750.cfg
@@ -0,0 +1,19 @@
+#STR750 CPU

+#use combined on interfaces or targets that can’t set TRST/SRST separately

+#reset_config trst_and_srst srst_pulls_trst

+reset_config trst_and_srst srst_pulls_trst

+#jtag scan chain

+#format L IRC IRCM IDCODE (Length, IR Capture, IR Capture Mask, IDCODE)

+jtag_device 4 0x1 0xf 0xe

+#jtag nTRST and nSRST delay

+jtag_nsrst_delay 500

+jtag_ntrst_delay 500

+#target configuration

+daemon_startup reset

+#target <type> <startup mode>

+#target arm7tdmi <reset mode> <chainpos> <endianness> <variant>

+target arm7tdmi little run_and_halt 0 arm7tdmi

+run_and_halt_time 0 30

+working_area 0 0x40000000 0x4000 nobackup

+#flash bank <driver> <base> <size> <chip_width> <bus_width>

+flash bank str7x 0x20000000 0x000040000 0 0 0 STR75x

diff --git a/src/target/target/str9comstick.cfg b/src/target/target/str9comstick.cfg
new file mode 100644
index 00000000..f9886674
--- /dev/null
+++ b/src/target/target/str9comstick.cfg
@@ -0,0 +1,19 @@
+#Hitex STR9 Comstick

+jtag_nsrst_delay 100

+jtag_ntrst_delay 100

+#use combined on interfaces or targets that can’t set TRST/SRST separately

+reset_config trst_and_srst

+#jtag scan chain

+#format L IRC IRCM IDCODE (Length, IR Capture, IR Capture Mask, IDCODE)

+jtag_device 8 0x1 0x1 0xfe

+jtag_device 4 0x1 0xf 0xe

+jtag_device 5 0x1 0x1 0x1e

+#target configuration

+daemon_startup reset

+#target <type> <startup mode>

+#target arm966e <endianness> <reset mode> <chainpos> <variant>

+target arm966e little reset_halt 1 arm966e

+run_and_halt_time 0 30

+working_area 0 0x50000000 16384 nobackup

+#flash bank <driver> <base> <size> <chip_width> <bus_width>

+flash bank str9x 0x00000000 0x00080000 0 0 0