diff options
author | David Brownell <dbrownell@users.sourceforge.net> | 2009-11-09 12:02:23 -0800 |
---|---|---|
committer | David Brownell <dbrownell@users.sourceforge.net> | 2009-11-09 12:02:23 -0800 |
commit | 9253ce9baea6f7b5ef3fc53b4bc0cfbff48194f4 (patch) | |
tree | 7a6a81b1e7006851c97ca07219d680b1caa25f52 | |
parent | 3885ab5a5af7ece410ce3eeb1059da3ea950436a (diff) | |
download | openocd_libswd-9253ce9baea6f7b5ef3fc53b4bc0cfbff48194f4.tar.gz openocd_libswd-9253ce9baea6f7b5ef3fc53b4bc0cfbff48194f4.tar.bz2 openocd_libswd-9253ce9baea6f7b5ef3fc53b4bc0cfbff48194f4.tar.xz openocd_libswd-9253ce9baea6f7b5ef3fc53b4bc0cfbff48194f4.zip |
User's Guide: Flash/NAND doc tweaks
Rename the "Drivers, Options, and Commands" sections to be
just "Driver List" matching the earlier reference. Add an
example of parallel CFI flash.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
-rw-r--r-- | doc/openocd.texi | 15 |
1 files changed, 12 insertions, 3 deletions
diff --git a/doc/openocd.texi b/doc/openocd.texi index d869f389..8e1d1a8f 100644 --- a/doc/openocd.texi +++ b/doc/openocd.texi @@ -3688,7 +3688,7 @@ The @var{num} parameter is a value shown by @command{flash banks}. @end deffn @anchor{Flash Driver List} -@section Flash Drivers, Options, and Commands +@section Flash Driver List As noted above, the @command{flash bank} command requires a driver name, and allows driver-specific options and behaviors. Some drivers also activate driver-specific commands. @@ -3704,7 +3704,7 @@ specific external chip select on the CPU. Frequently the first such chip is used to boot the system. Your board's @code{reset-init} handler might need to configure additional chip selects using other commands (like: @command{mww} to -configure a bus and its timings) , or +configure a bus and its timings), or perhaps configure a GPIO pin that controls the ``write protect'' pin on the flash chip. The CFI driver can use a target-specific working area to significantly @@ -3725,6 +3725,15 @@ wide on a sixteen bit bus: flash bank cfi 0x00000000 0x01000000 2 2 $_TARGETNAME flash bank cfi 0x01000000 0x01000000 2 2 $_TARGETNAME @end example + +To configure one bank of 32 MBytes +built from two sixteen bit (two byte) wide parts wired in parallel +to create a thirty-two bit (four byte) bus with doubled throughput: + +@example +flash bank cfi 0x00000000 0x02000000 2 4 $_TARGETNAME +@end example + @c "cfi part_id" disabled @end deffn @@ -4620,7 +4629,7 @@ with the wrong ECC data can cause them to be marked as bad. @end deffn @anchor{NAND Driver List} -@section NAND Drivers, Options, and Commands +@section NAND Driver List As noted above, the @command{nand device} command allows driver-specific options and behaviors. Some controllers also activate controller-specific commands. |