Move TCL script files -- Step 1 of 2:

- Move src/target/{interface,target,board,test}/ into src/tcl/
- Remove existing rules in src/Makefile.am and src/target/Makefile.am.
- Add Makefile.am handling of *.cfg and *.tcl files in top Makefile.am:
  - Add dist-hook to include such files under src/tcl in the distribution.
  - Add install-data-hook to install contents of '$(top_srcdir)/src/tcl/'.
  - Add uninstall-hook to remove the installed script files.
- Change paths to (un)install script files in '$(pkgdatadir)/scripts'.


git-svn-id: svn://svn.berlios.de/openocd/trunk@1918 b42882b7-edfa-0310-969c-e2dbd0fdcd60

1 files changed, 56 insertions, 0 deletions

diff --git a/src/tcl/target/lpc2148.cfg b/src/tcl/target/lpc2148.cfg
new file mode 100644
index 00000000..d367a8f5
--- /dev/null
+++ b/src/tcl/target/lpc2148.cfg
@@ -0,0 +1,56 @@
+# Use RCLK. If RCLK is not available fall back to 500kHz. 
+# 
+# Depending on cabling you might be able to eek this up to 2000kHz.
+jtag_rclk 500
+
+if { [info exists CHIPNAME] } {	
+   set _CHIPNAME $CHIPNAME
+} else {
+   set _CHIPNAME lpc2148
+}
+
+if { [info exists ENDIAN] } {
+   set _ENDIAN $ENDIAN
+} else {
+   set _ENDIAN little
+}
+
+if { [info exists CPUTAPID ] } {
+   set _CPUTAPID $CPUTAPID
+} else {
+   set _CPUTAPID 0x4f1f0f0f
+}
+
+jtag_nsrst_delay 200
+jtag_ntrst_delay 200
+
+# NOTE!!! LPCs need reset pulled while RTCK is low. 0 to activate
+# JTAG, power-on reset is not enough, i.e. you need to perform a
+# reset before being able to talk to the LPC2148, attach is not possible.
+
+reset_config trst_and_srst srst_pulls_trst
+
+jtag newtap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_CPUTAPID
+
+set _TARGETNAME [format "%s.cpu" $_CHIPNAME]
+
+target create $_TARGETNAME arm7tdmi -endian $_ENDIAN -chain-position $_TARGETNAME -variant arm7tdmi-s_r4
+
+$_TARGETNAME configure -work-area-virt 0 -work-area-phys 0x40000000 -work-area-size 0x4000 -work-area-backup 0
+
+$_TARGETNAME configure -event reset-init {
+	# Force target into ARM state.
+	soft_reset_halt
+
+	# Do not remap 0x0000-0x0020 to anything but the flash (i.e. select
+	# "User Flash Mode" where interrupt vectors are _not_ remapped,
+	# and reside in flash instead).
+	#
+	# See section 7.1 on page 32 ("Memory Mapping control register") in
+	# "UM10139: Volume 1: LPC214x User Manual", Rev. 02 -- 25 July 2006.
+	# http://www.standardics.nxp.com/support/documents/microcontrollers/pdf/user.manual.lpc2141.lpc2142.lpc2144.lpc2146.lpc2148.pdf
+	mwb 0xE01FC040 0x01
+}
+
+# flash bank lpc2000 <base> <size> 0 0 <target#> <variant> <clock> [calc_checksum]
+flash bank lpc2000 0x0 0x7d000 0 0 0 lpc2000_v2 14765 calc_checksum