summaryrefslogtreecommitdiff
diff options
context:
space:
mode:
-rw-r--r--src/target/board/crossbow_tech_imote2.cfg92
-rw-r--r--src/target/board/digi_connectcore_wi-9c.cfg254
-rw-r--r--src/target/board/hitex_stm32-performancestick.cfg100
-rw-r--r--src/target/board/hitex_str9-comstick.cfg144
-rw-r--r--src/target/board/linksys_nslu2.cfg16
-rw-r--r--src/target/board/pxa255_sst.cfg30
-rw-r--r--src/target/board/str910-eval.cfg122
-rw-r--r--src/target/board/zy1000.cfg220
-rw-r--r--src/target/interface/hitex_str9-comstick.cfg22
9 files changed, 500 insertions, 500 deletions
diff --git a/src/target/board/crossbow_tech_imote2.cfg b/src/target/board/crossbow_tech_imote2.cfg
index 8cdd7001..7527bef8 100644
--- a/src/target/board/crossbow_tech_imote2.cfg
+++ b/src/target/board/crossbow_tech_imote2.cfg
@@ -1,46 +1,46 @@
-# Crossbow Technology iMote2
-
-if { [info exists CHIPNAME] } {
- set _CHIPNAME $CHIPNAME
-} else {
- set _CHIPNAME imote2
-}
-
-if { [info exists ENDIAN] } {
- set _ENDIAN $ENDIAN
-} else {
- set _ENDIAN little
-}
-
-if { [info exists CPUTAPID ] } {
- set _CPUTAPID $CPUTAPID
-} else {
- # force an error till we get a good number
- set _CPUTAPID 0xffffffff
-}
-
-# PXA271 and an Intel Strataflash of 32 Megabytes (p30)
-#
-# Marvell/Intel PXA270 Script
-# set jtag_nsrst_delay to the delay introduced by your reset circuit
-# the rest of the needed delays are built into the openocd program
-jtag_nsrst_delay 800
-# set the jtag_ntrst_delay to the delay introduced by a reset circuit
-# the rest of the needed delays are built into the openocd program
-jtag_ntrst_delay 0
-#use combined on interfaces or targets that can't set TRST/SRST separately
-reset_config trst_and_srst separate
-#jtag scan chain
-
-jtag newtap $_CHIPNAME cpu -irlen 7 -ircapture 0x1 -irmask 0x7f -expected-id $_CPUTAPID
-
-set _TARGETNAME [format "%s.cpu" $_CHIPNAME]
-target create $_TARGETNAME xscale -endian $_ENDIAN -chain-position $_TARGETNAME -variant pxa27x
-$_TARGETNAME configure -work-area-virt 0x0x5c000000 -work-area-phys 0x0x5c000000 -work-area-size 0x10000 -work-area-backup 1
-# maps to PXA internal RAM. If you are using a PXA255
-# you must initialize SDRAM or leave this option off
-
-
-#flash bank <driver> <base> <size> <chip_width> <bus_width>
-# works for P30 flash
-flash bank cfi 0x00000000 0x2000000 2 2 0
+# Crossbow Technology iMote2
+
+if { [info exists CHIPNAME] } {
+ set _CHIPNAME $CHIPNAME
+} else {
+ set _CHIPNAME imote2
+}
+
+if { [info exists ENDIAN] } {
+ set _ENDIAN $ENDIAN
+} else {
+ set _ENDIAN little
+}
+
+if { [info exists CPUTAPID ] } {
+ set _CPUTAPID $CPUTAPID
+} else {
+ # force an error till we get a good number
+ set _CPUTAPID 0xffffffff
+}
+
+# PXA271 and an Intel Strataflash of 32 Megabytes (p30)
+#
+# Marvell/Intel PXA270 Script
+# set jtag_nsrst_delay to the delay introduced by your reset circuit
+# the rest of the needed delays are built into the openocd program
+jtag_nsrst_delay 800
+# set the jtag_ntrst_delay to the delay introduced by a reset circuit
+# the rest of the needed delays are built into the openocd program
+jtag_ntrst_delay 0
+#use combined on interfaces or targets that can't set TRST/SRST separately
+reset_config trst_and_srst separate
+#jtag scan chain
+
+jtag newtap $_CHIPNAME cpu -irlen 7 -ircapture 0x1 -irmask 0x7f -expected-id $_CPUTAPID
+
+set _TARGETNAME [format "%s.cpu" $_CHIPNAME]
+target create $_TARGETNAME xscale -endian $_ENDIAN -chain-position $_TARGETNAME -variant pxa27x
+$_TARGETNAME configure -work-area-virt 0x0x5c000000 -work-area-phys 0x0x5c000000 -work-area-size 0x10000 -work-area-backup 1
+# maps to PXA internal RAM. If you are using a PXA255
+# you must initialize SDRAM or leave this option off
+
+
+#flash bank <driver> <base> <size> <chip_width> <bus_width>
+# works for P30 flash
+flash bank cfi 0x00000000 0x2000000 2 2 0
diff --git a/src/target/board/digi_connectcore_wi-9c.cfg b/src/target/board/digi_connectcore_wi-9c.cfg
index 6b0e2a67..93317327 100644
--- a/src/target/board/digi_connectcore_wi-9c.cfg
+++ b/src/target/board/digi_connectcore_wi-9c.cfg
@@ -1,127 +1,127 @@
-######################################
-# Target: DIGI ConnectCore Wi-9C
-######################################
-
-reset_config trst_and_srst
-
-if { [info exists CHIPNAME] } {
- set _CHIPNAME $CHIPNAME
-} else {
- set _CHIPNAME ns9360
-}
-
-if { [info exists ENDIAN] } {
- set _ENDIAN $ENDIAN
-} else {
- # This config file was defaulting to big endian..
- set _ENDIAN big
-}
-
-
-# What's a good fallback frequency for this board if RCLK is
-# not available??
-jtag_rclk 1000
-
-
-if { [info exists CPUTAPID ] } {
- set _CPUTAPID $CPUTAPID
-} else {
- set _CPUTAPID 0xFFFFFFFF
-}
-
-set _TARGETNAME [format "%s.cpu" $_CHIPNAME]
-jtag newtap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_CPUTAPID
-
-jtag_nsrst_delay 200
-jtag_ntrst_delay 0
-
-
-######################
-# Target configuration
-######################
-
-target create $_TARGETNAME arm926ejs -endian $_ENDIAN -chain-position $_TARGETNAME -variant arm926ejs
-$_TARGETNAME configure -event reset-init {
- mww 0x90600104 0x33313333
- mww 0xA0700000 0x00000001 # Enable the memory controller.
- mww 0xA0700024 0x00000006 # Set the refresh counter 6
- mww 0xA0700028 0x00000001 #
- mww 0xA0700030 0x00000001 # Set the precharge period
- mww 0xA0700034 0x00000004 # Active to precharge command period is 16 clock cycles
- mww 0xA070003C 0x00000001 # tAPR
- mww 0xA0700040 0x00000005 # tDAL
- mww 0xA0700044 0x00000001 # tWR
- mww 0xA0700048 0x00000006 # tRC 32 clock cycles
- mww 0xA070004C 0x00000006 # tRFC 32 clock cycles
- mww 0xA0700054 0x00000001 # tRRD
- mww 0xA0700058 0x00000001 # tMRD
- mww 0xA0700100 0x00004280 # Dynamic Config 0 (cs4)
- mww 0xA0700120 0x00004280 # Dynamic Config 1 (cs5)
- mww 0xA0700140 0x00004280 # Dynamic Config 2 (cs6)
- mww 0xA0700160 0x00004280 # Dynamic Config 3 (cs7)
- #
- mww 0xA0700104 0x00000203 # CAS latency is 2 at 100 MHz
- mww 0xA0700124 0x00000203 # CAS latency is 2 at 100 MHz
- mww 0xA0700144 0x00000203 # CAS latency is 2 at 100 MHz
- mww 0xA0700164 0x00000203 # CAS latency is 2 at 100 MHz
- #
- mww 0xA0700020 0x00000103 # issue SDRAM PALL command
- #
- mww 0xA0700024 0x00000001 # Set the refresh counter to be as small as possible
- #
- # Add some dummy writes to give the SDRAM time to settle, it needs two
- # AHB clock cycles, here we poke in the debugger flag, this lets
- # the software know that we are in the debugger
- mww 0xA0900000 0x00000002
- mww 0xA0900000 0x00000002
- mww 0xA0900000 0x00000002
- mww 0xA0900000 0x00000002
- mww 0xA0900000 0x00000002
- #
- mdw 0xA0900000
- mdw 0xA0900000
- mdw 0xA0900000
- mdw 0xA0900000
- mdw 0xA0900000
- #
- mww 0xA0700024 0x00000030 # Set the refresh counter to 30
- mww 0xA0700020 0x00000083 # Issue SDRAM MODE command
- #
- # Next we perform a read of RAM.
- # mw = move word.
- mdw 0x00022000
- # mw 0x00022000:P, r3 # 22000 for cas2 latency, 32000 for cas 3
- #
- mww 0xA0700020 0x00000003 # issue SDRAM NORMAL command
- mww 0xA0700100 0x00084280 # Enable buffer access
- mww 0xA0700120 0x00084280 # Enable buffer access
- mww 0xA0700140 0x00084280 # Enable buffer access
- mww 0xA0700160 0x00084280 # Enable buffer access
-
- #Set byte lane state (static mem 1)"
- mww 0xA0700220, 0x00000082
- #Flash Start
- mww 0xA09001F8, 0x50000000
- #Flash Mask Reg
- mww 0xA09001FC, 0xFF000001
- mww 0xA0700028, 0x00000001
-
- # RAMAddr = 0x00020000
- # RAMSize = 0x00004000
-
- # Set the processor mode
- reg cpsr 0xd3
-}
-
-$_TARGETNAME configure -work-area-virt 0 -work-area-phys 0x00000000 -work-area-size 0x1000 -work-area-backup 1
-
-#####################
-# Flash configuration
-#####################
-
-#M29DW323DB - not working
-#flash bank cfi <base> <size> <chip width> <bus width> <target#>
-flash bank cfi 0x50000000 0x0400000 2 2 0
-
-
-
+######################################
+# Target: DIGI ConnectCore Wi-9C
+######################################
+
+reset_config trst_and_srst
+
+if { [info exists CHIPNAME] } {
+ set _CHIPNAME $CHIPNAME
+} else {
+ set _CHIPNAME ns9360
+}
+
+if { [info exists ENDIAN] } {
+ set _ENDIAN $ENDIAN
+} else {
+ # This config file was defaulting to big endian..
+ set _ENDIAN big
+}
+
+
+# What's a good fallback frequency for this board if RCLK is
+# not available??
+jtag_rclk 1000
+
+
+if { [info exists CPUTAPID ] } {
+ set _CPUTAPID $CPUTAPID
+} else {
+ set _CPUTAPID 0xFFFFFFFF
+}
+
+set _TARGETNAME [format "%s.cpu" $_CHIPNAME]
+jtag newtap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_CPUTAPID
+
+jtag_nsrst_delay 200
+jtag_ntrst_delay 0
+
+
+######################
+# Target configuration
+######################
+
+target create $_TARGETNAME arm926ejs -endian $_ENDIAN -chain-position $_TARGETNAME -variant arm926ejs
+$_TARGETNAME configure -event reset-init {
+ mww 0x90600104 0x33313333
+ mww 0xA0700000 0x00000001 # Enable the memory controller.
+ mww 0xA0700024 0x00000006 # Set the refresh counter 6
+ mww 0xA0700028 0x00000001 #
+ mww 0xA0700030 0x00000001 # Set the precharge period
+ mww 0xA0700034 0x00000004 # Active to precharge command period is 16 clock cycles
+ mww 0xA070003C 0x00000001 # tAPR
+ mww 0xA0700040 0x00000005 # tDAL
+ mww 0xA0700044 0x00000001 # tWR
+ mww 0xA0700048 0x00000006 # tRC 32 clock cycles
+ mww 0xA070004C 0x00000006 # tRFC 32 clock cycles
+ mww 0xA0700054 0x00000001 # tRRD
+ mww 0xA0700058 0x00000001 # tMRD
+ mww 0xA0700100 0x00004280 # Dynamic Config 0 (cs4)
+ mww 0xA0700120 0x00004280 # Dynamic Config 1 (cs5)
+ mww 0xA0700140 0x00004280 # Dynamic Config 2 (cs6)
+ mww 0xA0700160 0x00004280 # Dynamic Config 3 (cs7)
+ #
+ mww 0xA0700104 0x00000203 # CAS latency is 2 at 100 MHz
+ mww 0xA0700124 0x00000203 # CAS latency is 2 at 100 MHz
+ mww 0xA0700144 0x00000203 # CAS latency is 2 at 100 MHz
+ mww 0xA0700164 0x00000203 # CAS latency is 2 at 100 MHz
+ #
+ mww 0xA0700020 0x00000103 # issue SDRAM PALL command
+ #
+ mww 0xA0700024 0x00000001 # Set the refresh counter to be as small as possible
+ #
+ # Add some dummy writes to give the SDRAM time to settle, it needs two
+ # AHB clock cycles, here we poke in the debugger flag, this lets
+ # the software know that we are in the debugger
+ mww 0xA0900000 0x00000002
+ mww 0xA0900000 0x00000002
+ mww 0xA0900000 0x00000002
+ mww 0xA0900000 0x00000002
+ mww 0xA0900000 0x00000002
+ #
+ mdw 0xA0900000
+ mdw 0xA0900000
+ mdw 0xA0900000
+ mdw 0xA0900000
+ mdw 0xA0900000
+ #
+ mww 0xA0700024 0x00000030 # Set the refresh counter to 30
+ mww 0xA0700020 0x00000083 # Issue SDRAM MODE command
+ #
+ # Next we perform a read of RAM.
+ # mw = move word.
+ mdw 0x00022000
+ # mw 0x00022000:P, r3 # 22000 for cas2 latency, 32000 for cas 3
+ #
+ mww 0xA0700020 0x00000003 # issue SDRAM NORMAL command
+ mww 0xA0700100 0x00084280 # Enable buffer access
+ mww 0xA0700120 0x00084280 # Enable buffer access
+ mww 0xA0700140 0x00084280 # Enable buffer access
+ mww 0xA0700160 0x00084280 # Enable buffer access
+
+ #Set byte lane state (static mem 1)"
+ mww 0xA0700220, 0x00000082
+ #Flash Start
+ mww 0xA09001F8, 0x50000000
+ #Flash Mask Reg
+ mww 0xA09001FC, 0xFF000001
+ mww 0xA0700028, 0x00000001
+
+ # RAMAddr = 0x00020000
+ # RAMSize = 0x00004000
+
+ # Set the processor mode
+ reg cpsr 0xd3
+}
+
+$_TARGETNAME configure -work-area-virt 0 -work-area-phys 0x00000000 -work-area-size 0x1000 -work-area-backup 1
+
+#####################
+# Flash configuration
+#####################
+
+#M29DW323DB - not working
+#flash bank cfi <base> <size> <chip width> <bus width> <target#>
+flash bank cfi 0x50000000 0x0400000 2 2 0
+
+
+
diff --git a/src/target/board/hitex_stm32-performancestick.cfg b/src/target/board/hitex_stm32-performancestick.cfg
index da0ceb61..5effbd96 100644
--- a/src/target/board/hitex_stm32-performancestick.cfg
+++ b/src/target/board/hitex_stm32-performancestick.cfg
@@ -1,50 +1,50 @@
-# Hitex stm32 performance stick
-
-if { [info exists CHIPNAME] } {
- set _CHIPNAME $CHIPNAME
-} else {
- set _CHIPNAME stm32_hitex
-}
-
-if { [info exists ENDIAN] } {
- set _ENDIAN $ENDIAN
-} else {
- set _ENDIAN little
-}
-
-# set jtag speed
-jtag_khz 500
-
-jtag_nsrst_delay 100
-jtag_ntrst_delay 100
-
-#use combined on interfaces or targets that can't set TRST/SRST separately
-reset_config trst_and_srst
-
-#jtag scan chain
-# The CPU
-if { [info exists CPUTAPID ] } {
- set _CPUTAPID $CPUTAPID
-} else {
- # See STM Document RM0008
- # Section 26.6.3
- set _CPUTAPID 0x3ba00477
-}
-jtag newtap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_CPUTAPID
-
-# The boundery scan register, leave the "expected-id" undefined.
-jtag newtap $_CHIPNAME bs -irlen 5 -ircapture 0x1 -irmask 0x1
-
-# configure str750 connected to jtag chain
-jtag newtap $_CHIPNAME unknown -irlen 4 -ircapture 0x1 -irmask 0x0f
-
-set _TARGETNAME [format "%s.cpu" $_CHIPNAME]
-target create $_TARGETNAME cortex_m3 -endian $_ENDIAN -chain-position $_TARGETNAME
-
-$_TARGETNAME configure -work-area-virt 0 -work-area-phys 0x20000000 -work-area-size 16384 -work-area-backup 0
-
-#
-flash bank stm32x 0 0 0 0 0
-
-# For more information about the configuration files, take a look at:
-# openocd.texi
+# Hitex stm32 performance stick
+
+if { [info exists CHIPNAME] } {
+ set _CHIPNAME $CHIPNAME
+} else {
+ set _CHIPNAME stm32_hitex
+}
+
+if { [info exists ENDIAN] } {
+ set _ENDIAN $ENDIAN
+} else {
+ set _ENDIAN little
+}
+
+# set jtag speed
+jtag_khz 500
+
+jtag_nsrst_delay 100
+jtag_ntrst_delay 100
+
+#use combined on interfaces or targets that can't set TRST/SRST separately
+reset_config trst_and_srst
+
+#jtag scan chain
+# The CPU
+if { [info exists CPUTAPID ] } {
+ set _CPUTAPID $CPUTAPID
+} else {
+ # See STM Document RM0008
+ # Section 26.6.3
+ set _CPUTAPID 0x3ba00477
+}
+jtag newtap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_CPUTAPID
+
+# The boundery scan register, leave the "expected-id" undefined.
+jtag newtap $_CHIPNAME bs -irlen 5 -ircapture 0x1 -irmask 0x1
+
+# configure str750 connected to jtag chain
+jtag newtap $_CHIPNAME unknown -irlen 4 -ircapture 0x1 -irmask 0x0f
+
+set _TARGETNAME [format "%s.cpu" $_CHIPNAME]
+target create $_TARGETNAME cortex_m3 -endian $_ENDIAN -chain-position $_TARGETNAME
+
+$_TARGETNAME configure -work-area-virt 0 -work-area-phys 0x20000000 -work-area-size 16384 -work-area-backup 0
+
+#
+flash bank stm32x 0 0 0 0 0
+
+# For more information about the configuration files, take a look at:
+# openocd.texi
diff --git a/src/target/board/hitex_str9-comstick.cfg b/src/target/board/hitex_str9-comstick.cfg
index 0974f5ad..de4d56dd 100644
--- a/src/target/board/hitex_str9-comstick.cfg
+++ b/src/target/board/hitex_str9-comstick.cfg
@@ -1,72 +1,72 @@
-# Hitex STR9-comStick
-# http://www.hitex.com/index.php?id=383
-# This works for the STR9-comStick revisions STR912CS-A1 and STR912CS-A2.
-
-source [find interface/hitex_str9-comstick.cfg]
-
-# set jtag speed
-jtag_khz 3000
-
-jtag_nsrst_delay 100
-jtag_ntrst_delay 100
-#use combined on interfaces or targets that can't set TRST/SRST separately
-reset_config trst_and_srst
-#jtag scan chain
-#format L IRC IRCM IDCODE (Length, IR Capture, IR Capture Mask, IDCODE)
-
-if { [info exists CHIPNAME] } {
- set _CHIPNAME $CHIPNAME
-} else {
- set _CHIPNAME str912
-}
-
-if { [info exists ENDIAN] } {
- set _ENDIAN $ENDIAN
-} else {
- set _ENDIAN little
-}
-
-if { [info exists FLASHTAPID ] } {
- set _FLASHTAPID $FLASHTAPID
-} else {
- set _FLASHTAPID 0x04570041
-}
-jtag newtap $_CHIPNAME flash -irlen 8 -ircapture 0x1 -irmask 0x1 -expected-id $_FLASHTAPID
-
-if { [info exists CPUTAPID ] } {
- set _CPUTAPID $CPUTAPID
-} else {
- set _CPUTAPID 0x25966041
-}
-jtag newtap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_CPUTAPID
-
-if { [info exists BSTAPID ] } {
- set _BSTAPID $BSTAPID
-} else {
- # Found on STR9-comStick, revision STR912CS-A1
- set _BSTAPID1 0x1457f041
- # Found on STR9-comStick, revision STR912CS-A2
- set _BSTAPID2 0x2457f041
-}
-jtag newtap $_CHIPNAME bs -irlen 5 -ircapture 0x1 -irmask 0x1 -expected-id $_BSTAPID1 -expected-id $_BSTAPID2
-
-set _TARGETNAME [format "%s.cpu" $_CHIPNAME]
-target create $_TARGETNAME arm966e -endian $_ENDIAN -chain-position $_TARGETNAME -variant arm966e
-
-$_TARGETNAME configure -event reset-init {
- # We can increase speed now that we know the target is halted.
- #jtag_rclk 3000
-
- # -- Enable 96K RAM
- # PFQBC enabled / DTCM & AHB wait-states disabled
- mww 0x5C002034 0x0191
-
- str9x flash_config 0 4 2 0 0x80000
- flash protect 0 0 7 off
-}
-
-$_TARGETNAME configure -work-area-virt 0 -work-area-phys 0x50000000 -work-area-size 16384 -work-area-backup 0
-
-#flash bank <driver> <base> <size> <chip_width> <bus_width>
-flash bank str9x 0x00000000 0x00080000 0 0 0
-flash bank str9x 0x00080000 0x00008000 0 0 0
+# Hitex STR9-comStick
+# http://www.hitex.com/index.php?id=383
+# This works for the STR9-comStick revisions STR912CS-A1 and STR912CS-A2.
+
+source [find interface/hitex_str9-comstick.cfg]
+
+# set jtag speed
+jtag_khz 3000
+
+jtag_nsrst_delay 100
+jtag_ntrst_delay 100
+#use combined on interfaces or targets that can't set TRST/SRST separately
+reset_config trst_and_srst
+#jtag scan chain
+#format L IRC IRCM IDCODE (Length, IR Capture, IR Capture Mask, IDCODE)
+
+if { [info exists CHIPNAME] } {
+ set _CHIPNAME $CHIPNAME
+} else {
+ set _CHIPNAME str912
+}
+
+if { [info exists ENDIAN] } {
+ set _ENDIAN $ENDIAN
+} else {
+ set _ENDIAN little
+}
+
+if { [info exists FLASHTAPID ] } {
+ set _FLASHTAPID $FLASHTAPID
+} else {
+ set _FLASHTAPID 0x04570041
+}
+jtag newtap $_CHIPNAME flash -irlen 8 -ircapture 0x1 -irmask 0x1 -expected-id $_FLASHTAPID
+
+if { [info exists CPUTAPID ] } {
+ set _CPUTAPID $CPUTAPID
+} else {
+ set _CPUTAPID 0x25966041
+}
+jtag newtap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_CPUTAPID
+
+if { [info exists BSTAPID ] } {
+ set _BSTAPID $BSTAPID
+} else {
+ # Found on STR9-comStick, revision STR912CS-A1
+ set _BSTAPID1 0x1457f041
+ # Found on STR9-comStick, revision STR912CS-A2
+ set _BSTAPID2 0x2457f041
+}
+jtag newtap $_CHIPNAME bs -irlen 5 -ircapture 0x1 -irmask 0x1 -expected-id $_BSTAPID1 -expected-id $_BSTAPID2
+
+set _TARGETNAME [format "%s.cpu" $_CHIPNAME]
+target create $_TARGETNAME arm966e -endian $_ENDIAN -chain-position $_TARGETNAME -variant arm966e
+
+$_TARGETNAME configure -event reset-init {
+ # We can increase speed now that we know the target is halted.
+ #jtag_rclk 3000
+
+ # -- Enable 96K RAM
+ # PFQBC enabled / DTCM & AHB wait-states disabled
+ mww 0x5C002034 0x0191
+
+ str9x flash_config 0 4 2 0 0x80000
+ flash protect 0 0 7 off
+}
+
+$_TARGETNAME configure -work-area-virt 0 -work-area-phys 0x50000000 -work-area-size 16384 -work-area-backup 0
+
+#flash bank <driver> <base> <size> <chip_width> <bus_width>
+flash bank str9x 0x00000000 0x00080000 0 0 0
+flash bank str9x 0x00080000 0x00008000 0 0 0
diff --git a/src/target/board/linksys_nslu2.cfg b/src/target/board/linksys_nslu2.cfg
index 8c919d84..52984107 100644
--- a/src/target/board/linksys_nslu2.cfg
+++ b/src/target/board/linksys_nslu2.cfg
@@ -1,8 +1,8 @@
-# This is for the LinkSys (CISCO) NSLU2 board
-# It is an Intel XSCALE IXP420 CPU.
-
-source [find target/ixp42x.cfg]
-# The _TARGETNAME is set by the above.
-
-$_TARGETNAME configure -work-area-virt 0 -work-area-phys 0x00020000 -work-area-size 0x10000 -work-area-backup 0
-
+# This is for the LinkSys (CISCO) NSLU2 board
+# It is an Intel XSCALE IXP420 CPU.
+
+source [find target/ixp42x.cfg]
+# The _TARGETNAME is set by the above.
+
+$_TARGETNAME configure -work-area-virt 0 -work-area-phys 0x00020000 -work-area-size 0x10000 -work-area-backup 0
+
diff --git a/src/target/board/pxa255_sst.cfg b/src/target/board/pxa255_sst.cfg
index 199af4b4..37ff1a8b 100644
--- a/src/target/board/pxa255_sst.cfg
+++ b/src/target/board/pxa255_sst.cfg
@@ -1,15 +1,15 @@
-# A PXA255 test board with SST 39LF400A flash
-#
-# At reset the memory map is as follows. Note that
-# the memory map changes later on as the application
-# starts...
-#
-# RAM at 0x4000000
-# Flash at 0x00000000
-#
-source [find target/pxa255.cfg]
-# Target name is set by above
-$_TARGETNAME configure -work-area-virt 0 -work-area-phys 0x4000000 -work-area-size 0x4000 -work-area-backup 0
-# flash bank <driver> <base> <size> <chip_width> <bus_width> <targetNum> [options]
-flash bank cfi 0x00000000 0x80000 2 2 0 jedec_probe
-
+# A PXA255 test board with SST 39LF400A flash
+#
+# At reset the memory map is as follows. Note that
+# the memory map changes later on as the application
+# starts...
+#
+# RAM at 0x4000000
+# Flash at 0x00000000
+#
+source [find target/pxa255.cfg]
+# Target name is set by above
+$_TARGETNAME configure -work-area-virt 0 -work-area-phys 0x4000000 -work-area-size 0x4000 -work-area-backup 0
+# flash bank <driver> <base> <size> <chip_width> <bus_width> <targetNum> [options]
+flash bank cfi 0x00000000 0x80000 2 2 0 jedec_probe
+
diff --git a/src/target/board/str910-eval.cfg b/src/target/board/str910-eval.cfg
index 74341312..10a2100b 100644
--- a/src/target/board/str910-eval.cfg
+++ b/src/target/board/str910-eval.cfg
@@ -1,61 +1,61 @@
-# str910-eval eval board
-#
-# Need reset scripts
-reset_config trst_and_srst
-
-if { [info exists CHIPNAME] } {
- set _CHIPNAME $CHIPNAME
-} else {
- set _CHIPNAME str912
-}
-
-if { [info exists ENDIAN] } {
- set _ENDIAN $ENDIAN
-} else {
- set _ENDIAN little
-}
-
-if { [info exists FLASHTAPID ] } {
- set _FLASHTAPID $FLASHTAPID
-} else {
- set _FLASHTAPID 0x04570041
-}
-jtag newtap $_CHIPNAME flash -irlen 8 -ircapture 0x1 -irmask 0x1 -expected-id $_FLASHTAPID
-
-
-if { [info exists CPUTAPID ] } {
- set _CPUTAPID $CPUTAPID
-} else {
- set _CPUTAPID 0x25966041
-}
-jtag newtap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_CPUTAPID
-
-if { [info exists BSTAPID ] } {
- set _BSTAPID $BSTAPID
-} else {
- set _BSTAPID 0x1457f041
-}
-jtag newtap $_CHIPNAME bs -irlen 5 -ircapture 0x1 -irmask 0x1 -expected-id $_BSTAPID
-
-set _TARGETNAME [format "%s.cpu" $_CHIPNAME]
-target create $_TARGETNAME arm966e -endian $_ENDIAN -chain-position $_TARGETNAME -variant arm966e
-$_TARGETNAME configure -work-area-phys 0x50000000 -work-area-virt 0x50000000 -work-area-size 16384 -work-area-backup 1
-
-$_TARGETNAME configure -event reset-init {
- # We can increase speed now that we know the target is halted.
- #jtag_rclk 3000
-
- # -- Enable 96K RAM
- # PFQBC enabled / DTCM & AHB wait-states disabled
- mww 0x5C002034 0x0191
-
- str9x flash_config 0 4 2 0 0x80000
- flash protect 0 0 7 off
-}
-
-#flash bank str9x <base> <size> 0 0 <target#> <variant>
-flash bank str9x 0x00000000 0x00080000 0 0 0
-flash bank str9x 0x00080000 0x00008000 0 0 0
-
-# For more information about the configuration files, take a look at:
-# openocd.texi
+# str910-eval eval board
+#
+# Need reset scripts
+reset_config trst_and_srst
+
+if { [info exists CHIPNAME] } {
+ set _CHIPNAME $CHIPNAME
+} else {
+ set _CHIPNAME str912
+}
+
+if { [info exists ENDIAN] } {
+ set _ENDIAN $ENDIAN
+} else {
+ set _ENDIAN little
+}
+
+if { [info exists FLASHTAPID ] } {
+ set _FLASHTAPID $FLASHTAPID
+} else {
+ set _FLASHTAPID 0x04570041
+}
+jtag newtap $_CHIPNAME flash -irlen 8 -ircapture 0x1 -irmask 0x1 -expected-id $_FLASHTAPID
+
+
+if { [info exists CPUTAPID ] } {
+ set _CPUTAPID $CPUTAPID
+} else {
+ set _CPUTAPID 0x25966041
+}
+jtag newtap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_CPUTAPID
+
+if { [info exists BSTAPID ] } {
+ set _BSTAPID $BSTAPID
+} else {
+ set _BSTAPID 0x1457f041
+}
+jtag newtap $_CHIPNAME bs -irlen 5 -ircapture 0x1 -irmask 0x1 -expected-id $_BSTAPID
+
+set _TARGETNAME [format "%s.cpu" $_CHIPNAME]
+target create $_TARGETNAME arm966e -endian $_ENDIAN -chain-position $_TARGETNAME -variant arm966e
+$_TARGETNAME configure -work-area-phys 0x50000000 -work-area-virt 0x50000000 -work-area-size 16384 -work-area-backup 1
+
+$_TARGETNAME configure -event reset-init {
+ # We can increase speed now that we know the target is halted.
+ #jtag_rclk 3000
+
+ # -- Enable 96K RAM
+ # PFQBC enabled / DTCM & AHB wait-states disabled
+ mww 0x5C002034 0x0191
+
+ str9x flash_config 0 4 2 0 0x80000
+ flash protect 0 0 7 off
+}
+
+#flash bank str9x <base> <size> 0 0 <target#> <variant>
+flash bank str9x 0x00000000 0x00080000 0 0 0
+flash bank str9x 0x00080000 0x00008000 0 0 0
+
+# For more information about the configuration files, take a look at:
+# openocd.texi
diff --git a/src/target/board/zy1000.cfg b/src/target/board/zy1000.cfg
index 1d3eea26..d8bb4650 100644
--- a/src/target/board/zy1000.cfg
+++ b/src/target/board/zy1000.cfg
@@ -1,110 +1,110 @@
-#Script for ZY1000
-
-#Atmel ties SRST & TRST together, at which point it makes
-#no sense to use TRST, but use TMS instead.
-#
-#The annoying thing with tying SRST & TRST together is that
-#there is no way to halt the CPU *before and during* the
-#SRST reset, which means that the CPU will run a number
-#of cycles before it can be halted(as much as milliseconds).
-reset_config srst_only srst_pulls_trst
-
-
-if { [info exists CHIPNAME] } {
- set _CHIPNAME $CHIPNAME
-} else {
- set _CHIPNAME zy1000
-}
-
-if { [info exists ENDIAN] } {
- set _ENDIAN $ENDIAN
-} else {
- set _ENDIAN little
-}
-
-
-#jtag scan chain
-if { [info exists CPUTAPID ] } {
- set _CPUTAPID $CPUTAPID
-} else {
- set _CPUTAPID 0x1f0f0f0f
-}
-jtag newtap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_CPUTAPID
-
-set _TARGETNAME [format "%s.cpu" $_CHIPNAME]
-target create $_TARGETNAME arm7tdmi -endian $_ENDIAN -chain-position $_TARGETNAME -variant arm7tdmi-s_r4
-
-# at CPU CLK <32kHz this must be disabled
-arm7_9 fast_memory_access enable
-arm7_9 dcc_downloads enable
-
-flash bank ecosflash 0x01000000 0x200000 2 2 0 ecos/at91eb40a.elf
-$_TARGETNAME configure -event reset-init {
- # Set up chip selects & timings
- mww 0xFFE00000 0x0100273D
- mww 0xFFE00004 0x08002125
- mww 0xFFEe0008 0x02002125
- mww 0xFFE0000c 0x03002125
- mww 0xFFE00010 0x40000000
- mww 0xFFE00014 0x50000000
- mww 0xFFE00018 0x60000000
- mww 0xFFE0001c 0x70000000
- mww 0xFFE00020 0x00000001
- mww 0xFFE00024 0x00000000
-
- # remap
- mww 0xFFFFF124 0xFFFFFFFF
- mww 0xffff0010 0x100
- mww 0xffff0034 0x100
-
- #disable 16x5x UART interrupts
- mww 0x08020004 0
-}
-
-# required for usable performance. Used for lots of
-# other things than flash programming.
-$_TARGETNAME configure -work-area-virt 0 -work-area-phys 0x00020000 -work-area-size 0x20000 -work-area-backup 0
-
-jtag_khz 16000
-
-
-proc production_info {} {
- return "Serial number is official MAC number. Format XXXXXXXXXXXX"
-}
-
-# There is no return value from this procedure. If it is
-# successful it does not throw an exception
-#
-# Progress messages are output via puts
-proc production {firmwarefile serialnumber} {
- if {[string length $serialnumber]!=12} {
- puts "Invalid serial number"
- return
- }
-
- puts "Power cycling target"
- power off
- sleep 3000
- power on
- sleep 1000
- reset init
- flash write_image erase $firmwarefile 0x1000000 bin
- verify_image $firmwarefile 0x1000000 bin
-
- # Big endian... weee!!!!
- puts "Setting MAC number to $serialnumber"
- flash fillw [expr 0x1030000-0x8] "0x[string range $serialnumber 2 3][string range $serialnumber 0 1]0000" 1
- flash fillw [expr 0x1030000-0x4] "0x[string range $serialnumber 10 11][string range $serialnumber 8 9][string range $serialnumber 6 7][string range $serialnumber 4 5]" 1
- puts "Production successful"
-}
-
-
-proc production_test {} {
- power on
- sleep 1000
- target_request debugmsgs enable
- reset run
- sleep 25000
- target_request debugmsgs disable
- return "See IP address above..."
-}
+#Script for ZY1000
+
+#Atmel ties SRST & TRST together, at which point it makes
+#no sense to use TRST, but use TMS instead.
+#
+#The annoying thing with tying SRST & TRST together is that
+#there is no way to halt the CPU *before and during* the
+#SRST reset, which means that the CPU will run a number
+#of cycles before it can be halted(as much as milliseconds).
+reset_config srst_only srst_pulls_trst
+
+
+if { [info exists CHIPNAME] } {
+ set _CHIPNAME $CHIPNAME
+} else {
+ set _CHIPNAME zy1000
+}
+
+if { [info exists ENDIAN] } {
+ set _ENDIAN $ENDIAN
+} else {
+ set _ENDIAN little
+}
+
+
+#jtag scan chain
+if { [info exists CPUTAPID ] } {
+ set _CPUTAPID $CPUTAPID
+} else {
+ set _CPUTAPID 0x1f0f0f0f
+}
+jtag newtap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_CPUTAPID
+
+set _TARGETNAME [format "%s.cpu" $_CHIPNAME]
+target create $_TARGETNAME arm7tdmi -endian $_ENDIAN -chain-position $_TARGETNAME -variant arm7tdmi-s_r4
+
+# at CPU CLK <32kHz this must be disabled
+arm7_9 fast_memory_access enable
+arm7_9 dcc_downloads enable
+
+flash bank ecosflash 0x01000000 0x200000 2 2 0 ecos/at91eb40a.elf
+$_TARGETNAME configure -event reset-init {
+ # Set up chip selects & timings
+ mww 0xFFE00000 0x0100273D
+ mww 0xFFE00004 0x08002125
+ mww 0xFFEe0008 0x02002125
+ mww 0xFFE0000c 0x03002125
+ mww 0xFFE00010 0x40000000
+ mww 0xFFE00014 0x50000000
+ mww 0xFFE00018 0x60000000
+ mww 0xFFE0001c 0x70000000
+ mww 0xFFE00020 0x00000001
+ mww 0xFFE00024 0x00000000
+
+ # remap
+ mww 0xFFFFF124 0xFFFFFFFF
+ mww 0xffff0010 0x100
+ mww 0xffff0034 0x100
+
+ #disable 16x5x UART interrupts
+ mww 0x08020004 0
+}
+
+# required for usable performance. Used for lots of
+# other things than flash programming.
+$_TARGETNAME configure -work-area-virt 0 -work-area-phys 0x00020000 -work-area-size 0x20000 -work-area-backup 0
+
+jtag_khz 16000
+
+
+proc production_info {} {
+ return "Serial number is official MAC number. Format XXXXXXXXXXXX"
+}
+
+# There is no return value from this procedure. If it is
+# successful it does not throw an exception
+#
+# Progress messages are output via puts
+proc production {firmwarefile serialnumber} {
+ if {[string length $serialnumber]!=12} {
+ puts "Invalid serial number"
+ return
+ }
+
+ puts "Power cycling target"
+ power off
+ sleep 3000
+ power on
+ sleep 1000
+ reset init
+ flash write_image erase $firmwarefile 0x1000000 bin
+ verify_image $firmwarefile 0x1000000 bin
+
+ # Big endian... weee!!!!
+ puts "Setting MAC number to $serialnumber"
+ flash fillw [expr 0x1030000-0x8] "0x[string range $serialnumber 2 3][string range $serialnumber 0 1]0000" 1
+ flash fillw [expr 0x1030000-0x4] "0x[string range $serialnumber 10 11][string range $serialnumber 8 9][string range $serialnumber 6 7][string range $serialnumber 4 5]" 1
+ puts "Production successful"
+}
+
+
+proc production_test {} {
+ power on
+ sleep 1000
+ target_request debugmsgs enable
+ reset run
+ sleep 25000
+ target_request debugmsgs disable
+ return "See IP address above..."
+}
diff --git a/src/target/interface/hitex_str9-comstick.cfg b/src/target/interface/hitex_str9-comstick.cfg
index 0b98e8f8..32f19c68 100644
--- a/src/target/interface/hitex_str9-comstick.cfg
+++ b/src/target/interface/hitex_str9-comstick.cfg
@@ -1,11 +1,11 @@
-#
-# Hitex STR9-comStick
-#
-# http://www.hitex.com/index.php?id=383
-#
-
-interface ft2232
-ft2232_device_desc "STR9-comStick A"
-ft2232_layout comstick
-ft2232_vid_pid 0x0640 0x002c
-
+#
+# Hitex STR9-comStick
+#
+# http://www.hitex.com/index.php?id=383
+#
+
+interface ft2232
+ft2232_device_desc "STR9-comStick A"
+ft2232_layout comstick
+ft2232_vid_pid 0x0640 0x002c
+