diff options
Diffstat (limited to 'src/tcl/target')
52 files changed, 0 insertions, 2586 deletions
diff --git a/src/tcl/target/aduc702x.cfg b/src/tcl/target/aduc702x.cfg deleted file mode 100644 index ef1beb78..00000000 --- a/src/tcl/target/aduc702x.cfg +++ /dev/null @@ -1,61 +0,0 @@ -## -*- tcl -*- -## - - -if { [info exists CHIPNAME] } { - set _CHIPNAME $CHIPNAME -} else { - set _CHIPNAME s3c2410 -} - -if { [info exists ENDIAN] } { - set _ENDIAN $ENDIAN -} else { - # This config file was defaulting to big endian.. - set _ENDIAN little -} - -if { [info exists CPUTAPID] } { - set _CPUTAPID $CPUTAPID -} else { - set _CPUTAPID 0xffffffff -} - - -jtag_nsrst_delay 200 -jtag_ntrst_delay 200 - -# This is for the case that TRST/SRST is not wired on your JTAG adaptor. -# Don't really need them anyways. -reset_config none - -## JTAG scan chain -#format L IRC IRCM IDCODE (Length, IR Capture, IR Capture Mask, IDCODE) -jtag newtap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_CPUTAPID - -## -## Target configuration -## -set _TARGETNAME [format "%s.cpu" $_CHIPNAME] -target create $_TARGETNAME arm7tdmi -endian $_ENDIAN -chain-position $_TARGETNAME - -# allocate the entire SRAM as working area -$_TARGETNAME configure -work-area-phys 0x10000 -work-area-size 0x2000 - -## flash configuration -# only target number is needed -flash bank aduc702x 0 0 0 0 0 - -## If you use the watchdog, the following code makes sure that the board -## doesn't reboot when halted via JTAG. Yes, on the older generation -## AdUC702x, timer3 continues running even when the CPU is halted. - -proc watchdog_service {} { - global watchdog_hdl - mww 0xffff036c 0 -# puts "watchdog!!" - set watchdog_hdl [after 500 watchdog_service] -} - -$_TARGETNAME configure -event reset-halt-post { watchdog_service } -$_TARGETNAME configure -event old-pre_resume { global watchdog_hdl; after cancel $watchdog_hdl } diff --git a/src/tcl/target/at91eb40a.cfg b/src/tcl/target/at91eb40a.cfg deleted file mode 100644 index 39fbe095..00000000 --- a/src/tcl/target/at91eb40a.cfg +++ /dev/null @@ -1,61 +0,0 @@ -#Script for AT91EB40a - -if { [info exists CHIPNAME] } { - set _CHIPNAME $CHIPNAME -} else { - set _CHIPNAME at91eb40a -} - -if { [info exists ENDIAN] } { - set _ENDIAN $ENDIAN -} else { - set _ENDIAN little -} - -if { [info exists CPUTAPID ] } { - set _CPUTAPID $CPUTAPID -} else { - # force an error till we get a good number - set _CPUTAPID 0x1f0f0f0f -} - - -#Atmel ties SRST & TRST together, at which point it makes -#no sense to use TRST, but use TMS instead. -# -#The annoying thing with tying SRST & TRST together is that -#there is no way to halt the CPU *before and during* the -#SRST reset, which means that the CPU will run a number -#of cycles before it can be halted(as much as milliseconds). -reset_config srst_only srst_pulls_trst - -#jtag scan chain -#format L IRC IRCM IDCODE (Length, IR Capture, IR Capture Mask, IDCODE) -jtag newtap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_CPUTAPID - -#target configuration -set _TARGETNAME [format "%s.cpu" $_CHIPNAME] -target create $_TARGETNAME arm7tdmi -endian $_ENDIAN -chain-position $_TARGETNAME -variant arm7tdmi-s_r4 - -# speed up memory downloads -arm7_9 fast_memory_access enable -arm7_9 dcc_downloads enable - -#flash driver -flash bank ecosflash 0x01000000 0x200000 2 2 0 ecos/at91eb40a.elf - -# required for usable performance. Used for lots of -# other things than flash programming. -$_TARGETNAME configure -work-area-virt 0 -work-area-phys 0x00030000 -work-area-size 0x10000 -work-area-backup 0 - -$_TARGETNAME configure -event reset-init { - puts "Running reset init script for AT91EB40A" - # Reset script for AT91EB40a - reg cpsr 0x000000D3 - mww 0xFFE00020 0x1 - mww 0xFFE00024 0x00000000 - mww 0xFFE00000 0x01002539 - mww 0xFFFFF124 0xFFFFFFFF - mww 0xffff0010 0x100 - mww 0xffff0034 0x100 -} diff --git a/src/tcl/target/at91r40008.cfg b/src/tcl/target/at91r40008.cfg deleted file mode 100644 index f8f5d410..00000000 --- a/src/tcl/target/at91r40008.cfg +++ /dev/null @@ -1,50 +0,0 @@ - - -if { [info exists CHIPNAME] } { - set _CHIPNAME $CHIPNAME -} else { - set _CHIPNAME at9r40008 -} - -if { [info exists ENDIAN] } { - set _ENDIAN $ENDIAN -} else { - set _ENDIAN little -} - -if { [info exists CPUTAPID ] } { - set _CPUTAPID $CPUTAPID -} else { - # force an error till we get a good number - set _CPUTAPID 0xffffffff -} - -jtag_nsrst_delay 200 -jtag_ntrst_delay 200 - -#use combined on interfaces or targets that can't set TRST/SRST separately -reset_config srst_only srst_pulls_trst - -#jtag scan chain -#format L IRC IRCM IDCODE (Length, IR Capture, IR Capture Mask, IDCODE) -jtag newtap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_CPUTAPID -set _TARGETNAME [format "%s.cpu" $_CHIPNAME] -target create $_TARGETNAME arm7tdmi -endian $_ENDIAN -chain-position $_TARGETNAME -variant arm7tdmi - - -$_TARGETNAME configure -event gdb-flash-erase-start { - wait_halt - sleep 10 - poll - # Ethernut 3 remapping is required to access external flash memory. - mww 0xffe00000 0x1000213d - mww 0xffe00004 0x20003e3d - mww 0xffe00020 0x00000001 -} - -$_TARGETNAME configure -work-area-virt 0 -work-area-phys 0x3C000 -work-area-size 0x4000 -work-area-backup 0 - -flash bank cfi 0x10000000 0x400000 2 2 0 - -# For more information about the configuration files, take a look at: -# openocd.texi diff --git a/src/tcl/target/at91rm9200.cfg b/src/tcl/target/at91rm9200.cfg deleted file mode 100644 index 58c7318e..00000000 --- a/src/tcl/target/at91rm9200.cfg +++ /dev/null @@ -1,51 +0,0 @@ - -reset_config trst_and_srst - -if { [info exists CHIPNAME] } { - set _CHIPNAME $CHIPNAME -} else { - set _CHIPNAME at91rm9200 -} - -if { [info exists ENDIAN] } { - set _ENDIAN $ENDIAN -} else { - set _ENDIAN little -} - -if { [info exists CPUTAPID ] } { - set _CPUTAPID $CPUTAPID -} else { - set _CPUTAPID 0x05b0203f -} - -# Never allow the following! -if { $_CPUTAPID == 0x15b0203f } { - puts "-------------------------------------------------------" - puts "- ERROR: -" - puts "- ERROR: TapID 0x15b0203f is wrong for at91rm9200 -" - puts "- ERROR: The chip/board has a JTAG select pin/jumper -" - puts "- ERROR: -" - puts "- ERROR: In one position (0x05b0203f) it selects the -" - puts "- ERROR: ARM CPU, in the other position (0x1b0203f) -" - puts "- ERROR: it selects boundry-scan not the ARM -" - puts "- ERROR: -" - puts "-------------------------------------------------------" -} - -jtag newtap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_CPUTAPID - - -# Create the GDB Target. -set _TARGETNAME [format "%s.cpu" $_CHIPNAME] -target create $_TARGETNAME arm920t -endian $_ENDIAN -chain-position $_TARGETNAME -# AT91RM9200 has a 16K block of sram @ 0x0020.0000 -$_TARGETNAME configure -work-area-virt 0x00200000 -work-area-phys 0x00200000 -work-area-size 0x4000 -work-area-backup 1 - -# This chip has a DCC ... use it -arm7_9 dcc_downloads enable - - - - - diff --git a/src/tcl/target/at91sam9260.cfg b/src/tcl/target/at91sam9260.cfg deleted file mode 100644 index 4d51831d..00000000 --- a/src/tcl/target/at91sam9260.cfg +++ /dev/null @@ -1,42 +0,0 @@ -###################################### -# Target: Atmel AT91SAM9260 -###################################### - -if { [info exists CHIPNAME] } { - set _CHIPNAME $CHIPNAME -} else { - set _CHIPNAME at91sam9260 -} - -if { [info exists ENDIAN] } { - set _ENDIAN $ENDIAN -} else { - set _ENDIAN little -} - -if { [info exists CPUTAPID ] } { - set _CPUTAPID $CPUTAPID -} else { - # force an error till we get a good number - set _CPUTAPID 0x0792603f -} - -reset_config trst_and_srst - -# -jtag newtap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_CPUTAPID - -jtag_nsrst_delay 200 -jtag_ntrst_delay 200 - -###################### -# Target configuration -###################### - -set _TARGETNAME [format "%s.cpu" $_CHIPNAME] -target create $_TARGETNAME arm926ejs -endian $_ENDIAN -chain-position $_TARGETNAME -variant arm926ejs - -# Internal sram1 memory -$_TARGETNAME configure -work-area-virt 0 -work-area-phys 0x00300000 -work-area-size 0x1000 -work-area-backup 1 - - diff --git a/src/tcl/target/at91sam9260_ext_RAM_ext_flash.cfg b/src/tcl/target/at91sam9260_ext_RAM_ext_flash.cfg deleted file mode 100644 index f10a021c..00000000 --- a/src/tcl/target/at91sam9260_ext_RAM_ext_flash.cfg +++ /dev/null @@ -1,127 +0,0 @@ - - - -jtag_khz 4 - - -###################################### -# Target: Atmel AT91SAM9260 -###################################### - -if { [info exists CHIPNAME] } { - set _CHIPNAME $CHIPNAME -} else { - set _CHIPNAME at91sam9260 -} - -if { [info exists ENDIAN] } { - set _ENDIAN $ENDIAN -} else { - set _ENDIAN little -} - -if { [info exists CPUTAPID ] } { - set _CPUTAPID $CPUTAPID -} else { - # force an error till we get a good number - set _CPUTAPID 0x0792603f -} - -reset_config trst_and_srst - - -jtag_nsrst_delay 200 -jtag_ntrst_delay 200 - - -jtag newtap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_CPUTAPID - - -###################### -# Target configuration -###################### - -set _TARGETNAME [format "%s.cpu" $_CHIPNAME] -target create $_TARGETNAME arm926ejs -endian $_ENDIAN -chain-position $_TARGETNAME -variant arm926ejs - -$_TARGETNAME invoke-event halted - -# Internal sram1 memory -$_TARGETNAME configure -work-area-virt 0 -work-area-phys 0x00300000 -work-area-size 0x1000 -work-area-backup 1 - -scan_chain -$_TARGETNAME configure -event reset-deassert-post {at91sam_init} - - -# Flash configuration -#flash bank cfi <base> <size> <chip width> <bus width> <target#> -flash bank cfi 0x10000000 0x01000000 2 2 $_TARGETNAME - - -proc at91sam_init { } { - - # at reset chip runs at 32khz - jtag_khz 8 - halt - mww 0xfffffd08 0xa5000501 # RSTC_MR : enable user reset - mww 0xfffffd44 0x00008000 # WDT_MR : disable watchdog - - mww 0xfffffc20 0x00004001 # CKGR_MOR : enable the main oscillator - sleep 20 # wait 20 ms - mww 0xfffffc30 0x00000001 # PMC_MCKR : switch to main oscillator - sleep 10 # wait 10 ms - mww 0xfffffc28 0x2060bf09 # CKGR_PLLAR: Set PLLA Register for 198,656MHz - sleep 20 # wait 20 ms - mww 0xfffffc30 0x00000101 # PMC_MCKR : Select prescaler - sleep 10 # wait 10 ms - mww 0xfffffc30 0x00000102 # PMC_MCKR : Clock from PLLA is selected - sleep 10 # wait 10 ms - - # Now run at anything fast... ie: 10mhz! - jtag_khz 10000 # Increase JTAG Speed to 6 MHz - arm7_9 dcc_downloads enable # Enable faster DCC downloads - - mww 0xffffec00 0x0a0a0a0a # SMC_SETUP0 : Setup SMC for Intel NOR Flash JS28F128P30T85 128MBit - mww 0xffffec04 0x0b0b0b0b # SMC_PULSE0 - mww 0xffffec08 0x00160016 # SMC_CYCLE0 - mww 0xffffec0c 0x00161003 # SMC_MODE0 - - flash probe 0 # Identify flash bank 0 - - mww 0xfffff870 0xffff0000 # PIO_ASR : Select peripheral function for D15..D31 - mww 0xfffff804 0xffff0000 # PIO_PDR : Disable PIO function for D15..D31 - - mww 0xffffef1c 0x2 # EBI_CSA : Assign EBI Chip Select 1 to SDRAM - - mww 0xffffea08 0x85227259 # SDRAMC_CR : Configure SDRAM (2 x Samsung K4S561632H-UC75 : 4M x 16Bit x 4 Banks) - #mww 0xffffea08 0x85227254 # SDRAMC_CR : Configure SDRAM (2 x Samsung K4S641632H-UC75 : 1M x 16Bit x 4 Banks) - - mww 0xffffea00 0x1 # SDRAMC_MR : issue a NOP command - mww 0x20000000 0 - mww 0xffffea00 0x2 # SDRAMC_MR : issue an 'All Banks Precharge' command - mww 0x20000000 0 - mww 0xffffea00 0x4 # SDRAMC_MR : issue 8 x 'Auto-Refresh' Command - mww 0x20000000 0 - mww 0xffffea00 0x4 - mww 0x20000000 0 - mww 0xffffea00 0x4 - mww 0x20000000 0 - mww 0xffffea00 0x4 - mww 0x20000000 0 - mww 0xffffea00 0x4 - mww 0x20000000 0 - mww 0xffffea00 0x4 - mww 0x20000000 0 - mww 0xffffea00 0x4 - mww 0x20000000 0 - mww 0xffffea00 0x4 - mww 0x20000000 0 - mww 0xffffea00 0x3 # SDRAMC_MR : issue a 'Load Mode Register' command - mww 0x20000000 0 - mww 0xffffea00 0x0 # SDRAMC_MR : normal mode - mww 0x20000000 0 - mww 0xffffea04 0x5d2 # SDRAMC_TR : Set refresh timer count to 15us -} - - - diff --git a/src/tcl/target/davinci.cfg b/src/tcl/target/davinci.cfg deleted file mode 100644 index 0a3da27d..00000000 --- a/src/tcl/target/davinci.cfg +++ /dev/null @@ -1,170 +0,0 @@ -# -# Utility code for DaVinci-family chips -# - -# davinci_pinmux: assigns PINMUX$reg <== $value -proc davinci_pinmux {soc reg value} { - mww [expr [dict get $soc sysbase] + 4 * $reg] $value -} - -# mrw: "memory read word", returns value of $reg -proc mrw {reg} { - set value "" - ocd_mem2array value 32 $reg 1 - return $value(0) -} - -# mmw: "memory modify word", updates value of $reg -# $reg <== ((value & ~$clearbits) | $setbits) -proc mmw {reg setbits clearbits} { - set old [mrw $reg] - set new [expr ($old & ~$clearbits) | $setbits] - mww $reg $new -} - -# -# pll_setup: initialize PLL -# - pll_addr ... physical addr of controller -# - mult ... pll multiplier -# - config ... dict mapping { prediv, postdiv, div[1-9] } to dividers -# -# For PLLs that don't have a given register (e.g. plldiv8), or where a -# given divider is non-programmable, caller provides *NO* config mapping. -# -# REVISIT there are minor differences between the PLL controllers. -# Handle those; maybe check the ID register. This version behaves -# for at least the dm355. On dm6446 and dm357 the PLLRST polarity -# is different. On dm365 there are more changes. -# -proc pll_setup {pll_addr mult config} { - set pll_ctrl_addr [expr $pll_addr + 0x100] - set pll_ctrl [mrw $pll_ctrl_addr] - - # 1 - clear CLKMODE (bit 8) iff using on-chip oscillator - # NOTE: this assumes we should clear that bit - set pll_ctrl [expr $pll_ctrl & ~0x0100] - mww $pll_ctrl_addr $pll_ctrl - - # 2 - clear PLLENSRC (bit 5) - set pll_ctrl [expr $pll_ctrl & ~0x0020] - mww $pll_ctrl_addr $pll_ctrl - - # 3 - clear PLLEN (bit 0) ... enter bypass mode - set pll_ctrl [expr $pll_ctrl & ~0x0001] - mww $pll_ctrl_addr $pll_ctrl - - # 4 - wait at least 4 refclk cycles - sleep 1 - - # 5 - set PLLRST (bit 3) - set pll_ctrl [expr $pll_ctrl | 0x0008] - mww $pll_ctrl_addr $pll_ctrl - - # 6 - set PLLDIS (bit 4) - set pll_ctrl [expr $pll_ctrl | 0x0010] - mww $pll_ctrl_addr $pll_ctrl - - # 7 - clear PLLPWRDN (bit 1) - set pll_ctrl [expr $pll_ctrl & ~0x0002] - mww $pll_ctrl_addr $pll_ctrl - - # 8 - clear PLLDIS (bit 4) - set pll_ctrl [expr $pll_ctrl & ~0x0010] - mww $pll_ctrl_addr $pll_ctrl - - # 9 - optional: write prediv, postdiv, and pllm - # NOTE: for dm355 PLL1, postdiv is controlled via MISC register - mww [expr $pll_addr + 0x0110] [expr ($mult - 1) & 0xff] - if { [dict exists $config prediv] } { - set div [dict get $config prediv] - set div [expr 0x8000 | ($div - 1)] - mww [expr $pll_addr + 0x0114] $div - } - if { [dict exists $config postdiv] } { - set div [dict get $config postdiv] - set div [expr 0x8000 | ($div - 1)] - mww [expr $pll_addr + 0x0128] $div - } - - # 10 - optional: set plldiv1, plldiv2, ... - # NOTE: this assumes some registers have their just-reset values: - # - PLLSTAT.GOSTAT is clear when we enter - # - ALNCTL has everything set - set go 0 - if { [dict exists $config div1] } { - set div [dict get $config div1] - set div [expr 0x8000 | ($div - 1)] - mww [expr $pll_addr + 0x0118] $div - set go 1 - } - if { [dict exists $config div2] } { - 1et div [dict get $config div2] - set div [expr 0x8000 | ($div - 1)] - mww [expr $pll_addr + 0x011c] $div - set go 1 - } - if { [dict exists $config div3] } { - set div [dict get $config div3] - set div [expr 0x8000 | ($div - 1)] - mww [expr $pll_addr + 0x011c] $div - set go 1 - } - if { [dict exists $config div4] } { - set div [dict get $config div4] - set div [expr 0x8000 | ($div - 1)] - mww [expr $pll_addr + 0x0160] $div - set go 1 - } - if { [dict exists $config div5] } { - set div [dict get $config div5] - set div [expr 0x8000 | ($div - 1)] - mww [expr $pll_addr + 0x0164] $div - set go 1 - } - if {$go != 0} { - # write pllcmd.GO; poll pllstat.GO - mww [expr $pll_addr + 0x0138] 0x01 - set pllstat [expr $pll_addr + 0x013c] - while {[expr [mrw $pllstat] & 0x01] != 0} { sleep 1 } - } - - # 11 - wait at least 5 usec for reset to finish - # (assume covered by overheads including JTAG messaging) - - # 12 - clear PLLRST (bit 3) - set pll_ctrl [expr $pll_ctrl & ~0x0008] - mww $pll_ctrl_addr $pll_ctrl - - # 13 - wait at least 8000 refclk cycles for PLL to lock - # if we assume 24 MHz (slowest osc), that's 1/3 msec - sleep 3 - - # 14 - set PLLEN (bit 0) ... leave bypass mode - set pll_ctrl [expr $pll_ctrl | 0x0001] - mww $pll_ctrl_addr $pll_ctrl -} - -# NOTE: dm6446 requires EMURSTIE set in MDCTL before certain -# modules can be enabled. - -# prepare a non-DSP module to be enabled; finish with psc_go -proc psc_enable {module} { - set psc_addr 0x01c41000 - # write MDCTL - mmw [expr $psc_addr + 0x0a00 + (4 * $module)] 0x03 0x1f -} - -# execute non-DSP PSC transition(s) set up by psc_enable -proc psc_go {} { - set psc_addr 0x01c41000 - set ptstat_addr [expr $psc_addr + 0x0128] - - # just in case PTSTAT.go isn't clear - while { [expr [mrw $ptstat_addr] & 0x01] != 0 } { sleep 1 } - - # write PTCMD.go ... ignoring any DSP power domain - mww [expr $psc_addr + 0x0120] 1 - - # wait for PTSTAT.go to clear (again ignoring DSP power domain) - while { [expr [mrw $ptstat_addr] & 0x01] != 0 } { sleep 1 } -} diff --git a/src/tcl/target/epc9301.cfg b/src/tcl/target/epc9301.cfg deleted file mode 100644 index 6dbb91b3..00000000 --- a/src/tcl/target/epc9301.cfg +++ /dev/null @@ -1,31 +0,0 @@ -# Cirrus Logic EP9301 processor on an Olimex CS-E9301 board. - -if { [info exists CHIPNAME] } { - set _CHIPNAME $CHIPNAME -} else { - set _CHIPNAME ep9301 -} - -if { [info exists ENDIAN] } { - set _ENDIAN $ENDIAN -} else { - set _ENDIAN little -} - -if { [info exists CPUTAPID ] } { - set _CPUTAPID $CPUTAPID -} else { - # force an error till we get a good number - set _CPUTAPID 0xffffffff -} - -jtag newtap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_CPUTAPID -jtag_nsrst_delay 100 -jtag_ntrst_delay 100 - -set _TARGETNAME [format "%s.cpu" $_CHIPNAME] -target create $_TARGETNAME arm920t -endian $_ENDIAN -chain-position $_TARGETNAME -work-area-virt 0 -work-area-phys 0x80014000 -work-area-size 0x1000 -work-area-backup 1 - -#flash configuration -#flash bank <driver> <base> <size> <chip_width> <bus_width> [driver_options ...] -flash bank cfi 0x60000000 0x1000000 2 2 0 diff --git a/src/tcl/target/feroceon.cfg b/src/tcl/target/feroceon.cfg deleted file mode 100644 index 552831a8..00000000 --- a/src/tcl/target/feroceon.cfg +++ /dev/null @@ -1,30 +0,0 @@ -###################################### -# Target: Marvell Feroceon CPU core -###################################### - -if { [info exists CHIPNAME] } { - set _CHIPNAME $CHIPNAME -} else { - set _CHIPNAME feroceon -} - -if { [info exists ENDIAN] } { - set _ENDIAN $ENDIAN -} else { - set _ENDIAN little -} - -if { [info exists CPUTAPID ] } { - set _CPUTAPID $CPUTAPID -} else { - set _CPUTAPID 0x20a023d3 -} - -jtag newtap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_CPUTAPID -set _TARGETNAME [format "%s.cpu" $_CHIPNAME] -target create $_TARGETNAME feroceon -endian $_ENDIAN -chain-position $_TARGETNAME - -reset_config trst_and_srst -jtag_nsrst_delay 200 -jtag_ntrst_delay 200 - diff --git a/src/tcl/target/imx21.cfg b/src/tcl/target/imx21.cfg deleted file mode 100644 index fd2143e1..00000000 --- a/src/tcl/target/imx21.cfg +++ /dev/null @@ -1,32 +0,0 @@ -#use combined on interfaces or targets that can't set TRST/SRST separately -reset_config trst_and_srst - -if { [info exists CHIPNAME] } { - set _CHIPNAME $CHIPNAME -} else { - set _CHIPNAME imx21 -} - -if { [info exists ENDIAN] } { - set _ENDIAN $ENDIAN -} else { - set _ENDIAN little -} - - -# Note above there is 1 tap - -# The CPU tap -if { [info exists CPUTAPID ] } { - set _CPUTAPID $CPUTAPID -} else { - set _CPUTAPID 0x0792611f -} -jtag newtap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_CPUTAPID - - -# Create the GDB Target. -set _TARGETNAME [format "%s.cpu" $_CHIPNAME] -target create $_TARGETNAME arm926ejs -endian $_ENDIAN -chain-position $_TARGETNAME -variant arm926ejs - -arm7_9 dcc_downloads enable diff --git a/src/tcl/target/imx27.cfg b/src/tcl/target/imx27.cfg deleted file mode 100644 index 240a8498..00000000 --- a/src/tcl/target/imx27.cfg +++ /dev/null @@ -1,42 +0,0 @@ -#use combined on interfaces or targets that can't set TRST/SRST separately -reset_config trst_and_srst - -if { [info exists CHIPNAME] } { - set _CHIPNAME $CHIPNAME -} else { - set _CHIPNAME imx27 -} - -if { [info exists ENDIAN] } { - set _ENDIAN $ENDIAN -} else { - set _ENDIAN little -} - - -# Note above there are 2 taps - -# The bs tap -if { [info exists BSTAPID ] } { - set _BSTAPID $BSTAPID -} else { - set _BSTAPID 0x1b900f0f -} -jtag newtap $_CHIPNAME bs -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_BSTAPID - -# The CPU tap -if { [info exists CPUTAPID ] } { - set _CPUTAPID $CPUTAPID -} else { - set _CPUTAPID 0x07926121 -} -jtag newtap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_CPUTAPID - -# Create the GDB Target. -set _TARGETNAME [format "%s.cpu" $_CHIPNAME] -target create $_TARGETNAME arm926ejs -endian $_ENDIAN -chain-position $_TARGETNAME -variant arm926ejs -$_TARGETNAME configure -work-area-virt 0xffff4c00 -work-area-phys 0xffff4c00 -work-area-size 0x8000 -work-area-backup 1 -# Internal to the chip, there is 45K of SRAM -# - -arm7_9 dcc_downloads enable diff --git a/src/tcl/target/imx31.cfg b/src/tcl/target/imx31.cfg deleted file mode 100644 index 3fed2f82..00000000 --- a/src/tcl/target/imx31.cfg +++ /dev/null @@ -1,62 +0,0 @@ -# imx31 config -# - -reset_config trst_and_srst - -if { [info exists CHIPNAME] } { - set _CHIPNAME $CHIPNAME -} else { - set _CHIPNAME imx31 -} - -if { [info exists ENDIAN] } { - set _ENDIAN $ENDIAN -} else { - set _ENDIAN little -} - -if { [info exists CPUTAPID ] } { - set _CPUTAPID $CPUTAPID -} else { - set _CPUTAPID 0x07b3601d -} - -if { [info exists SDMATAPID ] } { - set _SDMATAPID $SDMATAPID -} else { - set _SDMATAPID 0x2190101d -} - -#======================================== -# The "system jtag controller" -# IMX31 reference manual, page 6-28 - figure 6-14 -if { [info exists SJCTAPID ] } { - set _SJCTAPID $SJCTAPID -} else { - set _SJCTAPID 0x2b900f0f -} -jtag newtap $_CHIPNAME sjc -irlen 4 -ircapture 0x0 -irmask 0x0 -expected-id $_SJCTAPID - -# The "SDMA" - <S>mart <DMA> controller debug tap -# Based on some IO pins - this can be disabled & removed -# See diagram: 6-14 -# SIGNAL NAME: -# SJC_MOD - controls multiplexer - disables ARM1136 -# SDMA_BYPASS - disables SDMA - -# -# Per ARM: DDI0211J_arm1136_r1p5_trm.pdf - the ARM 1136 as a 5 bit IR register -jtag newtap $_CHIPNAME cpu -irlen 5 -ircapture 0x1 -irmask 0x1f -expected-id $_CPUTAPID - -# No IDCODE for this TAP -jtag newtap $_CHIPNAME whatchacallit -irlen 4 -ircapture 0 -irmask 0xf -expected-id 0x0 - -# Per section 40.17.1, table 40-85 the IR register is 4 bits -# But this conflicts with Diagram 6-13, "3bits ir and drs" -jtag newtap $_CHIPNAME smda -irlen 5 -ircapture 0x1 -irmask 0x1f -expected-id $_SDMATAPID - -set _TARGETNAME [format "%s.cpu" $_CHIPNAME] -target create $_TARGETNAME arm11 -endian $_ENDIAN -chain-position $_TARGETNAME - - -proc power_restore {} { puts "Sensed power restore. No action." } -proc srst_deasserted {} { puts "Sensed nSRST deasserted. No action." } diff --git a/src/tcl/target/imx35.cfg b/src/tcl/target/imx35.cfg deleted file mode 100644 index d254c603..00000000 --- a/src/tcl/target/imx35.cfg +++ /dev/null @@ -1,50 +0,0 @@ -# imx35 config -# - -if { [info exists CHIPNAME] } { - set _CHIPNAME $CHIPNAME -} else { - set _CHIPNAME imx35 -} - -if { [info exists ENDIAN] } { - set _ENDIAN $ENDIAN -} else { - set _ENDIAN little -} - -if { [info exists CPUTAPID ] } { - set _CPUTAPID $CPUTAPID -} else { - set _CPUTAPID 0x07b3601d -} - -if { [info exists SDMATAPID ] } { - set _SDMATAPID $SDMATAPID -} else { - set _SDMATAPID 0x0882601d -} - -#======================================== -# The "system jtag controller" -# IMX31 reference manual, page 6-28 - figure 6-14 -if { [info exists SJCTAPID ] } { - set _SJCTAPID $SJCTAPID -} else { - set _SJCTAPID 0x2b900f0f -} - -jtag newtap $_CHIPNAME sjc -irlen 4 -ircapture 0x0 -irmask 0x0 -expected-id $_SJCTAPID - -jtag newtap $_CHIPNAME cpu -irlen 5 -ircapture 0x1 -irmask 0x1f -expected-id $_CPUTAPID - -# No IDCODE for this TAP -jtag newtap $_CHIPNAME whatchacallit -irlen 4 -ircapture 0 -irmask 0x0 -expected-id 0x0 - -jtag newtap $_CHIPNAME smda -irlen 5 -ircapture 0x1 -irmask 0x1f -expected-id $_SDMATAPID - -set _TARGETNAME [format "%s.cpu" $_CHIPNAME] -target create $_TARGETNAME arm11 -endian $_ENDIAN -chain-position $_TARGETNAME - -proc power_restore {} { puts "Sensed power restore. No action." } -proc srst_deasserted {} { puts "Sensed nSRST deasserted. No action." } diff --git a/src/tcl/target/is5114.cfg b/src/tcl/target/is5114.cfg deleted file mode 100644 index c28298c6..00000000 --- a/src/tcl/target/is5114.cfg +++ /dev/null @@ -1,49 +0,0 @@ -# script for Insilica IS-5114 -# AKA: Atmel AT76C114 - an ARM946 chip -# ATMEL sold his product line to Insilica... - -if { [info exists CHIPNAME] } { - set _CHIPNAME $CHIPNAME -} else { - set _CHIPNAME is5114 -} - -if { [info exists ENDIAN] } { - set _ENDIAN $ENDIAN -} else { - # this defaults to a little endian - set _ENDIAN little -} - -if { [info exists CPUTAPID ] } { - set _CPUTAPID $CPUTAPID -} else { - # force an error till we get a good number - set _CPUTAPID 0xffffffff -} - -# jtag speed. We need to stick to 16kHz until we've finished reset. -jtag_rclk 16 - -reset_config trst_and_srst - -# Do not specify a tap id here... -#OLD SYNTAX: jtag_device 8 0x1 0x1 0xfe -jtag newtap $_CHIPNAME unknown1 -irlen 8 -ircapture 0x01 -irmask 1 -#OLD SYNTAX: jtag_device 4 0x1 0xf 0xe -# This is the "arm946" chip. -jtag newtap $_CHIPNAME cpu -irlen 4 -ircapture 0x0e -irmask 0xf -#OLD SYNTAX: jtag_device 5 0x1 0x1 0x1e -jtag newtap $_CHIPNAME unknown2 -irlen 5 -ircapture 1 -irmask 1 - - -#arm946e-s and -set _TARGETNAME [format "%s.cpu" $_CHIPNAME] -target create $_TARGETNAME arm966e -endian $_ENDIAN -chain-position $_TARGETNAME -variant arm966e - -$_TARGETNAME configure -event reset-start { jtag_rclk 16 } -$_TARGETNAME configure -event reset-init { - # We can increase speed now that we know the target is halted. - jtag_rclk 3000 -} -$_TARGETNAME configure -work-area-phys 0x50000000 -work-area-virt 0x50000000 -work-area-size 16384 -work-area-backup 1 diff --git a/src/tcl/target/ixp42x.cfg b/src/tcl/target/ixp42x.cfg deleted file mode 100644 index 12ace990..00000000 --- a/src/tcl/target/ixp42x.cfg +++ /dev/null @@ -1,32 +0,0 @@ -#xscale ixp42x CPU - - -if { [info exists CHIPNAME] } { - set _CHIPNAME $CHIPNAME -} else { - set _CHIPNAME ixp42x -} - -if { [info exists ENDIAN] } { - set _ENDIAN $ENDIAN -} else { - # this defaults to a bigendian - set _ENDIAN big -} - -if { [info exists CPUTAPID ] } { - set _CPUTAPID $CPUTAPID -} else { - # force an error till we get a good number - set _CPUTAPID 0xffffffff -} - -#use combined on interfaces or targets that can?t set TRST/SRST separately -reset_config srst_only srst_pulls_trst -#jtag scan chain - -jtag newtap $_CHIPNAME cpu -irlen 7 -ircapture 0x1 -irmask 0x7f -expected-id $_CPUTAPID - -set _TARGETNAME [format "%s.cpu" $_CHIPNAME] -target create $_TARGETNAME xscale -endian $_ENDIAN -chain-position $_TARGETNAME -variant ixp42x - diff --git a/src/tcl/target/lm3s3748.cfg b/src/tcl/target/lm3s3748.cfg deleted file mode 100644 index 7321cb8a..00000000 --- a/src/tcl/target/lm3s3748.cfg +++ /dev/null @@ -1,49 +0,0 @@ -# Script for luminary lm3s3748 -# -# NB! work in progress! Duplicated from lm3s811.cfg, but does -# it need modification?? - -if { [info exists CHIPNAME] } { - set _CHIPNAME $CHIPNAME -} else { - set _CHIPNAME lm3s3748 -} - -if { [info exists ENDIAN] } { - set _ENDIAN $ENDIAN -} else { - # this defaults to a little endian - set _ENDIAN little -} - -if { [info exists CPUTAPID ] } { - set _CPUTAPID $CPUTAPID -} else { - # force an error till we get a good number - set _CPUTAPID 0x3ba00477 -} - -# RCLK -jtag_khz 500 - -jtag_nsrst_delay 100 -jtag_ntrst_delay 100 - -#lm3s3748 Evaluation Board has only srst -reset_config srst_only - -#jtag scan chain -jtag newtap $_CHIPNAME cpu -irlen 4 -ircapture 1 -irmask 0xf -expected-id $_CPUTAPID - - -# the luminary variant causes a software reset rather than asserting SRST -# this stops the debug registers from being cleared -# this will be fixed in later revisions of silicon -set _TARGETNAME [format "%s.cpu" $_CHIPNAME] -target create $_TARGETNAME cortex_m3 -endian $_ENDIAN -chain-position $_TARGETNAME -variant lm3s - -# 8k working area at base of ram -$_TARGETNAME configure -work-area-virt 0 -work-area-phys 0x20000000 -work-area-size 0x2000 -work-area-backup 0 - -#flash configuration -flash bank stellaris 0 0 0 0 0 diff --git a/src/tcl/target/lm3s6965.cfg b/src/tcl/target/lm3s6965.cfg deleted file mode 100644 index 27b104ff..00000000 --- a/src/tcl/target/lm3s6965.cfg +++ /dev/null @@ -1,46 +0,0 @@ -# script for luminary lm3s6965 - - -if { [info exists CHIPNAME] } { - set _CHIPNAME $CHIPNAME -} else { - set _CHIPNAME lm3s6965 -} - -if { [info exists ENDIAN] } { - set _ENDIAN $ENDIAN -} else { - # this defaults to a little endian - set _ENDIAN little -} - -if { [info exists CPUTAPID ] } { - set _CPUTAPID $CPUTAPID -} else { - # force an error till we get a good number - set _CPUTAPID 0x3ba00477 -} - -# jtag speed -jtag_khz 500 - -jtag_nsrst_delay 100 -jtag_ntrst_delay 100 - -#LM3S6965 Evaluation Board has only srst -reset_config srst_only - -#jtag scan chain -jtag newtap $_CHIPNAME cpu -irlen 4 -ircapture 1 -irmask 0xf -expected-id $_CPUTAPID - -# the luminary variant causes a software reset rather than asserting SRST -# this stops the debug registers from being cleared -# this will be fixed in later revisions of silicon -set _TARGETNAME [format "%s.cpu" $_CHIPNAME] -target create $_TARGETNAME cortex_m3 -endian $_ENDIAN -chain-position $_TARGETNAME -variant lm3s - -# 4k working area at base of ram -$_TARGETNAME configure -work-area-virt 0 -work-area-phys 0x20000000 -work-area-size 0x4000 -work-area-backup 0 - -#flash configuration -flash bank stellaris 0 0 0 0 0 diff --git a/src/tcl/target/lm3s811.cfg b/src/tcl/target/lm3s811.cfg deleted file mode 100644 index 2fa914fa..00000000 --- a/src/tcl/target/lm3s811.cfg +++ /dev/null @@ -1,45 +0,0 @@ -# Script for luminary lm3s811 - -if { [info exists CHIPNAME] } { - set _CHIPNAME $CHIPNAME -} else { - set _CHIPNAME lm3s811 -} - -if { [info exists ENDIAN] } { - set _ENDIAN $ENDIAN -} else { - # this defaults to a little endian - set _ENDIAN little -} - -if { [info exists CPUTAPID ] } { - set _CPUTAPID $CPUTAPID -} else { - # force an error till we get a good number - set _CPUTAPID 0x3ba00477 -} - -# jtag speed -jtag_khz 500 - -jtag_nsrst_delay 100 -jtag_ntrst_delay 100 - -#LM3S811 Evaluation Board has only srst -reset_config srst_only - -#jtag scan chain -jtag newtap $_CHIPNAME cpu -irlen 4 -ircapture 1 -irmask 0xf -expected-id $_CPUTAPID - -# the luminary variant causes a software reset rather than asserting SRST -# this stops the debug registers from being cleared -# this will be fixed in later revisions of silicon -set _TARGETNAME [format "%s.cpu" $_CHIPNAME] -target create $_TARGETNAME cortex_m3 -endian $_ENDIAN -chain-position $_TARGETNAME -variant lm3s - -# 8k working area at base of ram -$_TARGETNAME configure -work-area-virt 0 -work-area-phys 0x20000000 -work-area-size 0x2000 -work-area-backup 0 - -#flash configuration -flash bank stellaris 0 0 0 0 0 diff --git a/src/tcl/target/lpc2103.cfg b/src/tcl/target/lpc2103.cfg deleted file mode 100644 index cccc16d7..00000000 --- a/src/tcl/target/lpc2103.cfg +++ /dev/null @@ -1,39 +0,0 @@ -# NXP LPC2103 ARM7TDMI-S with 32kB Flash and 8kB SRAM, clocked with 12MHz crystal - -if { [info exists CHIPNAME] } { - set _CHIPNAME $CHIPNAME -} else { - set _CHIPNAME lpc2103 -} - -if { [info exists ENDIAN] } { - set _ENDIAN $ENDIAN -} else { - set _ENDIAN little -} - -if { [info exists CPUTAPID ] } { - set _CPUTAPID $CPUTAPID -} else { - set _CPUTAPID 0x4f1f0f0f -} - -# LPC2000 -> SRST causes TRST -reset_config trst_and_srst srst_pulls_trst - -# reset delays -jtag_nsrst_delay 100 -jtag_ntrst_delay 100 - -jtag newtap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_CPUTAPID - -set _TARGETNAME [format "%s.cpu" $_CHIPNAME] - -target create $_TARGETNAME arm7tdmi -endian $_ENDIAN -chain-position $_TARGETNAME -variant arm7tdmi-s_r4 - -# 8kB of internal SRAM -$_TARGETNAME configure -work-area-virt 0 -work-area-phys 0x40000000 -work-area-size 0x2000 -work-area-backup 0 - -# 32kB of internal Flash, core clocked with 12MHz crystal -# flash bank lpc2000 <base> <size> 0 0 <target#> <variant> <clock> [calc_checksum] -flash bank lpc2000 0x0 0x8000 0 0 0 lpc2000_v2 12000 calc_checksum diff --git a/src/tcl/target/lpc2124.cfg b/src/tcl/target/lpc2124.cfg deleted file mode 100644 index 4cdbc02c..00000000 --- a/src/tcl/target/lpc2124.cfg +++ /dev/null @@ -1,42 +0,0 @@ -#LPC-2124 CPU - -if { [info exists CHIPNAME] } { - set _CHIPNAME $CHIPNAME -} else { - set _CHIPNAME lpc2124 -} - -if { [info exists ENDIAN] } { - set _ENDIAN $ENDIAN -} else { - set _ENDIAN little -} - -if { [info exists CPUTAPID ] } { - set _CPUTAPID $CPUTAPID -} else { - # force an error till we get a good number - set _CPUTAPID 0x4f1f0f0f -} - - -#use combined on interfaces or targets that can't set TRST/SRST separately -reset_config trst_and_srst srst_pulls_trst - -# reset delays -jtag_nsrst_delay 100 -jtag_ntrst_delay 100 - -jtag_khz 1000 - -#jtag scan chain -jtag newtap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_CPUTAPID - -set _TARGETNAME [format "%s.cpu" $_CHIPNAME] -target create $_TARGETNAME arm7tdmi -endian $_ENDIAN -chain-position $_TARGETNAME -variant arm7tdmi-s_r4 - -$_TARGETNAME configure -work-area-virt 0 -work-area-phys 0x40000000 -work-area-size 0x4000 -work-area-backup 0 - - -#flash bank <driver> <base> <size> <chip_width> <bus_width> -flash bank lpc2000 0x0 0x40000 0 0 0 lpc2000_v1 14745 calc_checksum diff --git a/src/tcl/target/lpc2129.cfg b/src/tcl/target/lpc2129.cfg deleted file mode 100644 index b224c044..00000000 --- a/src/tcl/target/lpc2129.cfg +++ /dev/null @@ -1,41 +0,0 @@ -#LPC-2129 CPU - - -if { [info exists CHIPNAME] } { - set _CHIPNAME $CHIPNAME -} else { - set _CHIPNAME lpc2129 -} - -if { [info exists ENDIAN] } { - set _ENDIAN $ENDIAN -} else { - set _ENDIAN little -} - -if { [info exists CPUTAPID ] } { - set _CPUTAPID $CPUTAPID -} else { - # force an error till we get a good number - set _CPUTAPID 0xffffffff -} - - -#use combined on interfaces or targets that can't set TRST/SRST separately -reset_config trst_and_srst srst_pulls_trst - -# reset delays -jtag_nsrst_delay 100 -jtag_ntrst_delay 100 - -#jtag scan chain -jtag newtap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_CPUTAPID - - -set _TARGETNAME [format "%s.cpu" $_CHIPNAME] -target create $_TARGETNAME arm7tdmi -endian $_ENDIAN -chain-position $_TARGETNAME -variant arm7tdmi-s_r4 - -$_TARGETNAME configure -work-area-virt 0 -work-area-phys 0x40000000 -work-area-size 0x4000 -work-area-backup 0 - -#flash bank <driver> <base> <size> <chip_width> <bus_width> -flash bank lpc2000 0x0 0x40000 0 0 0 lpc2000_v1 14765 calc_checksum diff --git a/src/tcl/target/lpc2148.cfg b/src/tcl/target/lpc2148.cfg deleted file mode 100644 index d367a8f5..00000000 --- a/src/tcl/target/lpc2148.cfg +++ /dev/null @@ -1,56 +0,0 @@ -# Use RCLK. If RCLK is not available fall back to 500kHz. -# -# Depending on cabling you might be able to eek this up to 2000kHz. -jtag_rclk 500 - -if { [info exists CHIPNAME] } { - set _CHIPNAME $CHIPNAME -} else { - set _CHIPNAME lpc2148 -} - -if { [info exists ENDIAN] } { - set _ENDIAN $ENDIAN -} else { - set _ENDIAN little -} - -if { [info exists CPUTAPID ] } { - set _CPUTAPID $CPUTAPID -} else { - set _CPUTAPID 0x4f1f0f0f -} - -jtag_nsrst_delay 200 -jtag_ntrst_delay 200 - -# NOTE!!! LPCs need reset pulled while RTCK is low. 0 to activate -# JTAG, power-on reset is not enough, i.e. you need to perform a -# reset before being able to talk to the LPC2148, attach is not possible. - -reset_config trst_and_srst srst_pulls_trst - -jtag newtap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_CPUTAPID - -set _TARGETNAME [format "%s.cpu" $_CHIPNAME] - -target create $_TARGETNAME arm7tdmi -endian $_ENDIAN -chain-position $_TARGETNAME -variant arm7tdmi-s_r4 - -$_TARGETNAME configure -work-area-virt 0 -work-area-phys 0x40000000 -work-area-size 0x4000 -work-area-backup 0 - -$_TARGETNAME configure -event reset-init { - # Force target into ARM state. - soft_reset_halt - - # Do not remap 0x0000-0x0020 to anything but the flash (i.e. select - # "User Flash Mode" where interrupt vectors are _not_ remapped, - # and reside in flash instead). - # - # See section 7.1 on page 32 ("Memory Mapping control register") in - # "UM10139: Volume 1: LPC214x User Manual", Rev. 02 -- 25 July 2006. - # http://www.standardics.nxp.com/support/documents/microcontrollers/pdf/user.manual.lpc2141.lpc2142.lpc2144.lpc2146.lpc2148.pdf - mwb 0xE01FC040 0x01 -} - -# flash bank lpc2000 <base> <size> 0 0 <target#> <variant> <clock> [calc_checksum] -flash bank lpc2000 0x0 0x7d000 0 0 0 lpc2000_v2 14765 calc_checksum diff --git a/src/tcl/target/lpc2294.cfg b/src/tcl/target/lpc2294.cfg deleted file mode 100644 index c3746c1f..00000000 --- a/src/tcl/target/lpc2294.cfg +++ /dev/null @@ -1,38 +0,0 @@ -if { [info exists CHIPNAME] } { - set _CHIPNAME $CHIPNAME -} else { - set _CHIPNAME lpc2294 -} - -if { [info exists ENDIAN] } { - set _ENDIAN $ENDIAN -} else { - set _ENDIAN little -} - -if { [info exists CPUTAPID ] } { - set _CPUTAPID $CPUTAPID -} else { - # force an error till we get a good number - set _CPUTAPID 0xffffffff -} - -jtag_nsrst_delay 200 -jtag_ntrst_delay 200 - -#use combined on interfaces or targets that can't set TRST/SRST separately -reset_config trst_and_srst srst_pulls_trst - -#jtag scan chain -jtag newtap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_CPUTAPID - -set _TARGETNAME [format "%s.cpu" $_CHIPNAME] -target create $_TARGETNAME arm7tdmi -endian $_ENDIAN -chain-position $_TARGETNAME -variant arm7tdmi-s_r4 -$_TARGETNAME configure -work-area-virt 0 -work-area-phys 0x40000000 -work-area-size 0x4000 -work-area-backup 0 - -#flash configuration -#flash bank lpc2000 <base> <size> 0 0 <target#> <variant> -flash bank lpc2000 0x0 0x40000 0 0 0 lpc2000_v1 14765 calc_checksum - -# For more information about the configuration files, take a look at: -# openocd.texi diff --git a/src/tcl/target/lpc2378.cfg b/src/tcl/target/lpc2378.cfg deleted file mode 100644 index 16232383..00000000 --- a/src/tcl/target/lpc2378.cfg +++ /dev/null @@ -1,49 +0,0 @@ -# NXP LPC2378 ARM7TDMI-S with 512kB Flash and 32kB Local On-Chip SRAM (58kB total), clocked with 4MHz internal RC oscillator - -if { [info exists CHIPNAME] } { - set _CHIPNAME $CHIPNAME -} else { - set _CHIPNAME lpc2378 -} - -if { [info exists ENDIAN] } { - set _ENDIAN $ENDIAN -} else { - set _ENDIAN little -} - -if { [info exists CPUTAPID ] } { - set _CPUTAPID $CPUTAPID -} else { - set _CPUTAPID 0x4f1f0f0f -} - -#delays on reset lines -jtag_nsrst_delay 200 -jtag_ntrst_delay 200 - -# LPC2000 -> SRST causes TRST -reset_config trst_and_srst srst_pulls_trst - -jtag newtap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_CPUTAPID - -set _TARGETNAME [format "%s.cpu" $_CHIPNAME] -target create $_TARGETNAME arm7tdmi -endian $_ENDIAN -chain-position $_TARGETNAME -variant arm7tdmi-s_r4 - -# LPC2378 has 32kB of SRAM on its main system bus (so-called Local On-Chip SRAM) -$_TARGETNAME configure -work-area-virt 0 -work-area-phys 0x40000000 -work-area-size 0x8000 -work-area-backup 0 - -$_TARGETNAME configure -event reset-init { - # Force target into ARM state - soft_reset_halt - #do not remap 0x0000-0x0020 to anything but the flash - mwb 0xE01FC040 0x01 -} - -# LPC2378 has 512kB of FLASH, but upper 8kB are occupied by bootloader. -# After reset the chip uses its internal 4MHz RC oscillator -#flash bank lpc2000 <base> <size> 0 0 <target#> <variant> -flash bank lpc2000 0x0 0x0007D000 0 0 0 lpc2000_v2 4000 calc_checksum - -# 4MHz / 6 = 666kHz, so use 500 -jtag_khz 500 diff --git a/src/tcl/target/lpc2478.cfg b/src/tcl/target/lpc2478.cfg deleted file mode 100644 index 84675705..00000000 --- a/src/tcl/target/lpc2478.cfg +++ /dev/null @@ -1,35 +0,0 @@ -# Testing feeedback wanted! -set _CHIPNAME lpc2478 -set _ENDIAN little -set _CPUTAPID 0x4f1f0f0f - -# Use RCLK. If RCLK is not available fall back to 500kHz. -# -# Depending on cabling you might be able to eek this up to 2000kHz. -jtag_rclk 500 - -jtag_nsrst_delay 200 -jtag_ntrst_delay 200 - -#use combined on interfaces or targets that can't set TRST/SRST separately -reset_config trst_and_srst srst_pulls_trst - - -jtag newtap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_CPUTAPID - -set _TARGETNAME [format "%s.cpu" $_CHIPNAME] -target create $_TARGETNAME arm7tdmi -endian $_ENDIAN -chain-position $_TARGETNAME -variant arm7tdmi-s_r4 -$_TARGETNAME configure -work-area-virt 0 -work-area-phys 0x40000000 -work-area-size 0x4000 -work-area-backup 0 - - -$_TARGETNAME configure -event reset-init { - # Force target into ARM state - soft_reset_halt - # FIX!!!! should we remap the range below??? Is this applicable to - # Copied from LPC2148. - #do not remap 0x0000-0x0020 to anything but the flash - mwb 0xE01FC040 0x01 -} - - -flash bank lpc2000 0x0 0x7D000 0 0 0 lpc2000_v2 12000 calc_checksum diff --git a/src/tcl/target/mega128.cfg b/src/tcl/target/mega128.cfg deleted file mode 100644 index 964542c9..00000000 --- a/src/tcl/target/mega128.cfg +++ /dev/null @@ -1,42 +0,0 @@ -# for avr - - set _CHIPNAME avr - set _ENDIAN little - -# jtag speed -jtag_khz 4500 - -reset_config srst_only -jtag_nsrst_delay 100 - -#jtag scan chain -if { [info exists CPUTAPID ] } { - set _CPUTAPID $CPUTAPID -} else { - set _CPUTAPID 0x8970203F -} -jtag newtap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_CPUTAPID - -set _TARGETNAME [format "%s.cpu" $_CHIPNAME] -target create $_TARGETNAME avr -endian $_ENDIAN -chain-position $_TARGETNAME - -#$_TARGETNAME configure -work-area-virt 0 -work-area-phys 0x20000000 -work-area-size 16384 -work-area-backup 0 - -flash bank avr 0 0 0 0 0 - -#to use it, script will be like: -#init -#jtag_khz 4500 -#reset init -#verify_ircapture disable -# -#halt -#wait halt -#poll -#avr mass_erase 0 -#flash write_image E:/Versaloon/Software/CAMERAPROTOCOLAGENT.hex -#reset run -#shutdown -# -# For more information about the configuration files, take a look at: -# openocd.texi diff --git a/src/tcl/target/netx500.cfg b/src/tcl/target/netx500.cfg deleted file mode 100644 index c639017b..00000000 --- a/src/tcl/target/netx500.cfg +++ /dev/null @@ -1,34 +0,0 @@ -#Hilscher netX 500 CPU - - -if { [info exists CHIPNAME] } { - set _CHIPNAME $CHIPNAME -} else { - set _CHIPNAME netx500 -} - -if { [info exists ENDIAN] } { - set _ENDIAN $ENDIAN -} else { - set _ENDIAN little -} - -if { [info exists CPUTAPID ] } { - set _CPUTAPID $CPUTAPID -} else { - # force an error till we get a good number - set _CPUTAPID 0xffffffff -} - - -#use combined on interfaces or targets that can't set TRST/SRST separately -reset_config trst_and_srst -#jtag scan chain -# -jtag newtap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_CPUTAPID -jtag_nsrst_delay 100 -jtag_ntrst_delay 100 - -set _TARGETNAME [format "%s.cpu" $_CHIPNAME] -target create $_TARGETNAME arm926ejs -endian $_ENDIAN -chain-position $_TARGETNAME -variant arm926ejs - diff --git a/src/tcl/target/omap3530.cfg b/src/tcl/target/omap3530.cfg deleted file mode 100644 index ad8f8ea8..00000000 --- a/src/tcl/target/omap3530.cfg +++ /dev/null @@ -1,57 +0,0 @@ -#File omap3530.cfg - as found on the BEAGLEBOARD -# Assumption is it is generic for all OMAP3530 - -#TI OMAP3 processor - http://www.ti.com - -if { [info exists CHIPNAME] } { - set _CHIPNAME $CHIPNAME -} else { - set _CHIPNAME omap3 -} - -if { [info exists ENDIAN] } { - set _ENDIAN $ENDIAN -} else { - # this defaults to a little endianness - set _ENDIAN little -} - -if { [info exists CPUTAPID ] } { - set _CPUTAPID $CPUTAPID -} else { - # force an error till we get a good number - set _CPUTAPID 0x0B6D602F -} - -#jtag scan chain -jtag newtap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0x0 -expected-id $_CPUTAPID -disable -jtag newtap $_CHIPNAME jrc -irlen 6 -ircapture 0x1 -irmask 0xf -expected-id 0x0b7ae02f - -target create omap3.cpu cortex_m3 -endian little -chain-position omap3.cpu - -jtag configure $_CHIPNAME.cpu -event tap-enable { - puts "Enabling Cortex-A8 @ OMAP3" - irscan omap3.jrc 7 -endstate IRPAUSE - drscan omap3.jrc 8 0x89 -endstate DRPAUSE - irscan omap3.jrc 2 -endstate IRPAUSE - drscan omap3.jrc 32 0xa3002108 -endstate RUN/IDLE - irscan omap3.jrc 0x3F -endstate RUN/IDLE - runtest 10 - puts "Cortex-A8 @ OMAP3 enabled" -} - -proc omap3_dbginit { } { - version - jtag tapenable omap3.cpu - targets - # sleep 1000 - # dap apsel 1 - # sleep 1000 - # dap apsel 1 - # dap info 1 - omap3.cpu mww 0x54011FB0 0xC5ACCE55 4 - omap3.cpu mdw 0x54011314 - omap3.cpu mdw 0x54011314 - # omap3.cpu mdw 0x54011080 - omap3.cpu mww 0x5401d030 0x00002000 4 -} diff --git a/src/tcl/target/omap5912.cfg b/src/tcl/target/omap5912.cfg deleted file mode 100644 index 2942ad74..00000000 --- a/src/tcl/target/omap5912.cfg +++ /dev/null @@ -1,63 +0,0 @@ -#TI OMAP5912 dual core processor - http://www.ti.com -#on a OMAP5912 OSK board http://www.spectrumdigital.com. - -if { [info exists CHIPNAME] } { - set _CHIPNAME $CHIPNAME -} else { - set _CHIPNAME omap5912 -} - -if { [info exists ENDIAN] } { - set _ENDIAN $ENDIAN -} else { - # this defaults to a bigendian - set _ENDIAN little -} - -if { [info exists CPUTAPID ] } { - set _CPUTAPID $CPUTAPID -} else { - # force an error till we get a good number - set _CPUTAPID 0xffffffff -} - -#use combined on interfaces or targets that can't set TRST/SRST separately -reset_config trst_and_srst - -#jtag scan chain -jtag newtap $_CHIPNAME unknown1 -irlen 38 -ircapture 0x0 -irmask 0x0 -jtag newtap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0x0 -expected-id $_CPUTAPID -jtag newtap $_CHIPNAME unknown2 irlen 8 -ircapture 0x0 -irmask 0x0 - -set _TARGETNAME [format "%s.cpu" $_CHIPNAME] -target create $_TARGETNAME arm926ejs -endian $_ENDIAN -chain-position $_TARGETNAME -variant arm926ejs - -$_TARGETNAME configure -event reset-init { - # - # halt target - # - poll - sleep 1 - halt - wait_halt - # - # disable wdt - # - mww 0xfffec808 0x000000f5 - mww 0xfffec808 0x000000a0 - - mww 0xfffeb048 0x0000aaaa - sleep 500 - mww 0xfffeb048 0x00005555 - sleep 500 - # - # detect flash - # - flash probe 0 -} - -# omap5912 lcd frame buffer as working area -$_TARGETNAME configure -work-area-virt 0 -work-area-phys 0x20000000 -work-area-size 0x3e800 -work-area-backup 0 - -#flash bank <driver> <base> <size> <chip_width> <bus_width> -flash bank cfi 0x00000000 0x1000000 2 2 0 diff --git a/src/tcl/target/pic32mx.cfg b/src/tcl/target/pic32mx.cfg deleted file mode 100644 index 139f801f..00000000 --- a/src/tcl/target/pic32mx.cfg +++ /dev/null @@ -1,40 +0,0 @@ - -if { [info exists CHIPNAME] } { - set _CHIPNAME $CHIPNAME -} else { - set _CHIPNAME pic32mx -} - -if { [info exists ENDIAN] } { - set _ENDIAN $ENDIAN -} else { - set _ENDIAN little -} - -if { [info exists CPUTAPID ] } { - set _CPUTAPID $CPUTAPID -} else { - # force an error till we get a good number - set _CPUTAPID 0x30938053 -} - -jtag_nsrst_delay 100 -jtag_ntrst_delay 100 - -#use combined on interfaces or targets that can't set TRST/SRST separately -reset_config srst_only - -#jtag scan chain -#format L IRC IRCM IDCODE (Length, IR Capture, IR Capture Mask, IDCODE) -jtag newtap $_CHIPNAME cpu -irlen 5 -ircapture 0x1 -irmask 0x1f -expected-id $_CPUTAPID - -set _TARGETNAME [format "%s.cpu" $_CHIPNAME] -target create $_TARGETNAME mips_m4k -endian $_ENDIAN -chain-position $_TARGETNAME - -$_TARGETNAME configure -work-area-virt 0 -work-area-phys 0xa0000000 -work-area-size 16384 -work-area-backup 0 - -flash bank pic32mx 0xbd000000 0 0 0 0 -flash bank pic32mx 0xbfc00000 0 0 0 0 - -# For more information about the configuration files, take a look at: -# openocd.texi diff --git a/src/tcl/target/pxa255.cfg b/src/tcl/target/pxa255.cfg deleted file mode 100644 index c79ea4c9..00000000 --- a/src/tcl/target/pxa255.cfg +++ /dev/null @@ -1,104 +0,0 @@ -if { [info exists CHIPNAME] } { - set _CHIPNAME $CHIPNAME -} else { - set _CHIPNAME pxa255 -} - -if { [info exists ENDIAN] } { - set _ENDIAN $ENDIAN -} else { - set _ENDIAN little -} - -if { [info exists CPUTAPID ] } { - set _CPUTAPID $CPUTAPID -} else { - # force an error till we get a good number - set _CPUTAPID 0xffffffff -} - -jtag newtap $_CHIPNAME cpu -irlen 5 -ircapture 0x1 -irmask 0x1f -expected-id $_CPUTAPID - -jtag_nsrst_delay 200 -jtag_ntrst_delay 200 -set _TARGETNAME [format "%s.cpu" $_CHIPNAME] -target create $_TARGETNAME xscale -endian $_ENDIAN -chain-position $_TARGETNAME -variant pxa255 -$_TARGETNAME configure -event reset-init { - xscale cp15 15 0x00002001 #Enable CP0 and CP13 access - # - # setup GPIO - # - mww 0x40E00018 0x00008000 #CPSR0 - sleep 20 - mww 0x40E0001C 0x00000002 #GPSR1 - sleep 20 - mww 0x40E00020 0x00000008 #GPSR2 - sleep 20 - mww 0x40E0000C 0x00008000 #GPDR0 - sleep 20 - mww 0x40E00054 0x80000000 #GAFR0_L - sleep 20 - mww 0x40E00058 0x00188010 #GAFR0_H - sleep 20 - mww 0x40E0005C 0x60908018 #GAFR1_L - sleep 20 - mww 0x40E0000C 0x0280E000 #GPDR0 - sleep 20 - mww 0x40E00010 0x821C88B2 #GPDR1 - sleep 20 - mww 0x40E00014 0x000F03DB #GPDR2 - sleep 20 - mww 0x40E00000 0x000F03DB #GPLR0 - sleep 20 - - - mww 0x40F00004 0x00000020 #PSSR - sleep 20 - - # - # setup memory controller - # - mww 0x48000008 0x01111998 #MSC0 - sleep 20 - mww 0x48000010 0x00047ff0 #MSC2 - sleep 20 - mww 0x48000014 0x00000000 #MECR - sleep 20 - mww 0x48000028 0x00010504 #MCMEM0 - sleep 20 - mww 0x4800002C 0x00010504 #MCMEM1 - sleep 20 - mww 0x48000030 0x00010504 #MCATT0 - sleep 20 - mww 0x48000034 0x00010504 #MCATT1 - sleep 20 - mww 0x48000038 0x00004715 #MCIO0 - sleep 20 - mww 0x4800003C 0x00004715 #MCIO1 - sleep 20 - # - mww 0x48000004 0x03CA4018 #MDREF - sleep 20 - mww 0x48000004 0x004B4018 #MDREF - sleep 20 - mww 0x48000004 0x000B4018 #MDREF - sleep 20 - mww 0x48000004 0x000BC018 #MDREF - sleep 20 - mww 0x48000000 0x00001AC8 #MDCNFG - sleep 20 - - sleep 20 - - mww 0x48000000 0x00001AC9 #MDCNFG - sleep 20 - mww 0x48000040 0x00000000 #MDMRS - sleep 20 -} - -reset_config trst_and_srst - - - -#xscale debug_handler 0 0xFFFF0800 # debug handler base address - diff --git a/src/tcl/target/pxa270.cfg b/src/tcl/target/pxa270.cfg deleted file mode 100644 index 34bb60d4..00000000 --- a/src/tcl/target/pxa270.cfg +++ /dev/null @@ -1,39 +0,0 @@ -#Marvell/Intel PXA270 Script - -if { [info exists CHIPNAME] } { - set _CHIPNAME $CHIPNAME -} else { - set _CHIPNAME pxa270 -} - -if { [info exists ENDIAN] } { - set _ENDIAN $ENDIAN -} else { - set _ENDIAN little -} - -#IDs for pxa270. Choose one. Are there others?# -#set CPUTAPID 0x79265013 -#set CPUTAPID 0x49265013 -if { [info exists CPUTAPID ] } { - set _CPUTAPID $CPUTAPID -} else { - # force an error till we get a good number - set _CPUTAPID 0xffffffff -} - - -# set jtag_nsrst_delay to the delay introduced by your reset circuit -# the rest of the needed delays are built into the openocd program -jtag_nsrst_delay 260 -# set the jtag_ntrst_delay to the delay introduced by a reset circuit -# the rest of the needed delays are built into the openocd program -jtag_ntrst_delay 0 - -set _TARGETNAME [format "%s.cpu" $_CHIPNAME] -jtag newtap $_CHIPNAME cpu -irlen 7 -ircapture 0x1 -irmask 0x7f -expected-id $_CPUTAPID - -target create $_TARGETNAME xscale -endian $_ENDIAN -chain-position $_TARGETNAME -variant pxa27x -# maps to PXA internal RAM. If you are using a PXA255 -# you must initialize SDRAM or leave this option off -$_TARGETNAME configure -work-area-virt 0 -work-area-phys 0x5c000000 -work-area-size 0x10000 -work-area-backup 0 diff --git a/src/tcl/target/readme.txt b/src/tcl/target/readme.txt deleted file mode 100644 index ca23c64b..00000000 --- a/src/tcl/target/readme.txt +++ /dev/null @@ -1,41 +0,0 @@ -Prerequisites: -The users of OpenOCD as well as computer programs interacting with OpenOCD are expecting that certain commands -do the same thing across all the targets. - -Rules to follow when writing scripts: - -1. The configuration script should be defined such as , for example, the following sequences are working: - reset - flash info <bank> -and - reset - flash erase_address <start> <len> -and - reset init - load - -In most cases this can be accomplished by specifying the default startup mode as reset_init (target command -in the configuration file). - -2. If the target is correctly configured, flash must be writable without any other helper commands. It is -assumed that all write-protect mechanisms should be disabled. - -3. The configuration scripts should be defined such as the binary that was written to flash verifies -(turn off remapping, checksums, etc...) - -flash write_image [file] <parameters> -verify_image [file] <parameters> - -4. jtag_khz sets the maximum speed (or alternatively RCLK). If invoked -multiple times only the last setting is used. - -interface/xxx.cfg files are always executed *before* target/xxx.cfg -files, so any jtag_khz in interface/xxx.cfg will be overridden by -target/xxx.cfg. jtag_khz in interface/xxx.cfg would then, effectively, -set the default JTAG speed. - -Note that a target/xxx.cfg file can invoke another target/yyy.cfg file, -so one can create target subtype configurations where e.g. only -amount of DRAM, oscillator speeds differ and having a single -config file for the default/common settings. - diff --git a/src/tcl/target/sam7se512.cfg b/src/tcl/target/sam7se512.cfg deleted file mode 100644 index 6f0aa38c..00000000 --- a/src/tcl/target/sam7se512.cfg +++ /dev/null @@ -1,39 +0,0 @@ - -# ATMEL sam7se512 -# Example: the "Elektor Internet Radio" - EIR -# http://www.ethernut.de/en/hardware/eir/index.html - -if { [info exists CHIPNAME] } { - set _CHIPNAME $CHIPNAME -} else { - set _CHIPNAME sam7se512 -} - -if { [info exists ENDIAN] } { - set _ENDIAN $ENDIAN -} else { - set _ENDIAN little -} - -if { [info exists CPUTAPID ] } { - set _CPUTAPID $CPUTAPID -} else { - # force an error till we get a good number - set _CPUTAPID 0xffffffff -} - -#use combined on interfaces or targets that can't set TRST/SRST separately -reset_config srst_only srst_pulls_trst - -#jtag scan chain -jtag newtap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_CPUTAPID - -# The target -set _TARGETNAME [format "%s.cpu" $_CHIPNAME] -target create $_TARGETNAME arm7tdmi -endian $_ENDIAN -chain-position $_TARGETNAME -variant arm7tdmi - -$_TARGETNAME configure -work-area-virt 0 -work-area-phys 0x00200000 -work-area-size 0x4000 -work-area-backup 0 - -#flash bank <driver> <base_addr> <size> <chip_width> <bus_width> <target_number> [<target_name> <banks> <sectors_per_bank> <pages_per_sector> <page_size> <num_nvmbits> <ext_freq_khz>] -flash bank at91sam7 0 0 0 0 0 0 0 0 0 0 0 0 18432 - diff --git a/src/tcl/target/sam7x256.cfg b/src/tcl/target/sam7x256.cfg deleted file mode 100644 index 789f7dd6..00000000 --- a/src/tcl/target/sam7x256.cfg +++ /dev/null @@ -1,52 +0,0 @@ -#use combined on interfaces or targets that can't set TRST/SRST separately -reset_config srst_only srst_pulls_trst - -if { [info exists CHIPNAME] } { - set _CHIPNAME $CHIPNAME -} else { - set _CHIPNAME sam7x256 -} - -if { [info exists ENDIAN] } { - set _ENDIAN $ENDIAN -} else { - set _ENDIAN little -} - -if { [info exists CPUTAPID ] } { - set _CPUTAPID $CPUTAPID -} else { - set _CPUTAPID 0x3f0f0f0f -} - -jtag newtap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_CPUTAPID - -set _TARGETNAME [format "%s.cpu" $_CHIPNAME] - -target create $_TARGETNAME arm7tdmi -endian $_ENDIAN -chain-position $_TARGETNAME -variant arm7tdmi -$_TARGETNAME configure -event reset-init { - # disable watchdog - mww 0xfffffd44 0x00008000 - # enable user reset - mww 0xfffffd08 0xa5000001 - # CKGR_MOR : enable the main oscillator - mww 0xfffffc20 0x00000601 - sleep 10 - # CKGR_PLLR: 96.1097 MHz - mww 0xfffffc2c 0x00481c0e - sleep 10 - # PMC_MCKR : MCK = PLL / 2 ~= 48 MHz - mww 0xfffffc30 0x00000007 - sleep 10 - # MC_FMR: flash mode (FWS=1,FMCN=60) - mww 0xffffff60 0x003c0100 - sleep 100 -} - -$_TARGETNAME configure -work-area-virt 0 -work-area-phys 0x00200000 -work-area-size 0x4000 -work-area-backup 0 - -#flash bank <driver> <base_addr> <size> <chip_width> <bus_width> <target_number> [<target_name> <banks> <sectors_per_bank> <pages_per_sector> <page_size> <num_nvmbits> <ext_freq_khz>] -flash bank at91sam7 0 0 0 0 0 0 0 0 0 0 0 0 18432 - -# For more information about the configuration files, take a look at: -# openocd.texi diff --git a/src/tcl/target/samsung_s3c2410.cfg b/src/tcl/target/samsung_s3c2410.cfg deleted file mode 100644 index 3c0768bc..00000000 --- a/src/tcl/target/samsung_s3c2410.cfg +++ /dev/null @@ -1,35 +0,0 @@ -# Found on the 'TinCanTools' Hammer board. - -if { [info exists CHIPNAME] } { - set _CHIPNAME $CHIPNAME -} else { - set _CHIPNAME s3c2410 -} - -if { [info exists ENDIAN] } { - set _ENDIAN $ENDIAN -} else { - # This config file was defaulting to big endian.. - set _ENDIAN little -} - -if { [info exists CPUTAPID] } { - set _CPUTAPID $CPUTAPID -} else { - set _CPUTAPID 0xffffffff -} - -#use combined on interfaces or targets that cannot set TRST/SRST separately -reset_config trst_and_srst - -#jtag scan chain -jtag newtap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_CPUTAPID - -set _TARGETNAME [format "%s.cpu" $_CHIPNAME] -target create $_TARGETNAME arm920t -endian $_ENDIAN -chain-position $_TARGETNAME -variant arm920t - -$_TARGETNAME configure -work-area-virt 0 -work-area-phys 0x30800000 -work-area-size 0x20000 -work-area-backup 0 - -# speed up memory downloads -arm7_9 fast_memory_access enable -arm7_9 dcc_downloads enable diff --git a/src/tcl/target/samsung_s3c2440.cfg b/src/tcl/target/samsung_s3c2440.cfg deleted file mode 100644 index 12bb4085..00000000 --- a/src/tcl/target/samsung_s3c2440.cfg +++ /dev/null @@ -1,35 +0,0 @@ -# Target configuration for the Samsung 2440 system on chip -# Tested on a S3C2440 Evaluation board by keesj -# Processor : ARM920Tid(wb) rev 0 (v4l) -# Info: JTAG tap: s3c2440.cpu tap/device found: 0x0032409d (Manufacturer: 0x04e, Part: 0x0324, Version: 0x0) - -if { [info exists CHIPNAME] } { - set _CHIPNAME $CHIPNAME -} else { - set _CHIPNAME s3c2440 -} - -if { [info exists ENDIAN] } { - set _ENDIAN $ENDIAN -} else { - # this defaults to a bigendian - set _ENDIAN little -} - -if { [info exists CPUTAPID ] } { - set _CPUTAPID $CPUTAPID -} else { - # force an error till we get a good number - set _CPUTAPID 0x0032409d -} - -#jtag scan chain -jtag newtap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0x0f -expected-id $_CPUTAPID - -set _TARGETNAME [format "%s.cpu" $_CHIPNAME] -target create $_TARGETNAME arm920t -endian $_ENDIAN -chain-position $_TARGETNAME -variant arm920t -$_TARGETNAME configure -work-area-virt 0 -work-area-phys 0x200000 -work-area-size 0x4000 -work-area-backup 1 - -#reset configuration -reset_config trst_and_srst - diff --git a/src/tcl/target/samsung_s3c4510.cfg b/src/tcl/target/samsung_s3c4510.cfg deleted file mode 100644 index 65e7fd84..00000000 --- a/src/tcl/target/samsung_s3c4510.cfg +++ /dev/null @@ -1,25 +0,0 @@ - -if { [info exists CHIPNAME] } { - set _CHIPNAME $CHIPNAME -} else { - set _CHIPNAME s3c4510 -} - -if { [info exists ENDIAN] } { - set _ENDIAN $ENDIAN -} else { - set _ENDIAN little -} - - -# This appears to be a "Version 1" arm7tdmi. -if { [info exists CPUTAPID ] } { - set _CPUTAPID $CPUTAPID -} else { - set _CPUTAPID 0x1f0f0f0f -} -jtag newtap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_CPUTAPID - -set _TARGETNAME [format "%s.cpu" $_CHIPNAME] -target create $_TARGETNAME arm7tdmi -endian $_ENDIAN -chain-position $_TARGETNAME - diff --git a/src/tcl/target/samsung_s3c6410.cfg b/src/tcl/target/samsung_s3c6410.cfg deleted file mode 100644 index 4991c811..00000000 --- a/src/tcl/target/samsung_s3c6410.cfg +++ /dev/null @@ -1,49 +0,0 @@ -# -*- tcl -*- -# Target configuration for the Samsung s3c6410 system on chip -# Tested on a SMDK6410 -# Processor : ARM1176 -# Info: JTAG device found: 0x0032409d (Manufacturer: 0x04e, Part: 0x0324, Version: 0x0) -# [Duane Ellis 27/nov/2008: Above 0x0032409d appears to be copy/paste from other places] -# [and I do not believe it to be accurate, hence the 0xffffffff below] - -if { [info exists CHIPNAME] } { - set _CHIPNAME $CHIPNAME -} else { - set _CHIPNAME s3c6410 -} - -if { [info exists ENDIAN] } { - set _ENDIAN $ENDIAN -} else { - # this defaults to a bigendian - set _ENDIAN little -} - -if { [info exists BSTAPID ] } { - set _BSTAPID $BSTAPID -} else { - # force an error till we get a good number - set _BSTAPID 0x2b900f0f -} - -if { [info exists CPUTAPID ] } { - set _CPUTAPID $CPUTAPID -} else { - # force an error till we get a good number - set _CPUTAPID 0x07b76f0f -} - -#jtag scan chain - -# I think the "unknown" is the boundry scan tap -jtag newtap $_CHIPNAME unknown -irlen 4 -ircapture 0x1 -irmask 0xe -expected-id $_BSTAPID -jtag newtap $_CHIPNAME cpu -irlen 5 -ircapture 0x1 -irmask 0x1f -expected-id $_CPUTAPID - -set _TARGETNAME [format "%s.cpu" $_CHIPNAME] -target create $_TARGETNAME arm11 -endian $_ENDIAN -chain-position $_TARGETNAME -variant arm1176 - -jtag_nsrst_delay 500 -jtag_ntrst_delay 500 - -#reset configuration -reset_config trst_and_srst diff --git a/src/tcl/target/sharp_lh79532.cfg b/src/tcl/target/sharp_lh79532.cfg deleted file mode 100644 index a239e3c5..00000000 --- a/src/tcl/target/sharp_lh79532.cfg +++ /dev/null @@ -1,26 +0,0 @@ -reset_config srst_only srst_pulls_trst - -if { [info exists CHIPNAME] } { - set _CHIPNAME $CHIPNAME -} else { - set _CHIPNAME lh79532 -} - -if { [info exists ENDIAN] } { - set _ENDIAN $ENDIAN -} else { - set _ENDIAN little -} - -if { [info exists CPUTAPID ] } { - set _CPUTAPID $CPUTAPID -} else { - # sharp changed the number! - set _CPUTAPID 0x00002061 -} -jtag newtap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_CPUTAPID - -set _TARGETNAME [format "%s.cpu" $_CHIPNAME] -target create $_TARGETNAME arm7tdmi -endian $_ENDIAN -chain-position $_TARGETNAME - - diff --git a/src/tcl/target/smdk6410.cfg b/src/tcl/target/smdk6410.cfg deleted file mode 100644 index 6ce07cae..00000000 --- a/src/tcl/target/smdk6410.cfg +++ /dev/null @@ -1,8 +0,0 @@ -# Target configuration for the Samsung s3c6410 system on chip -# Tested on a SMDK6410 -# Processor : ARM1176 -# Info: JTAG device found: 0x0032409d (Manufacturer: 0x04e, Part: 0x0324, Version: 0x0) - -source [find target/samsung_s3c6410.cfg] - -flash bank cfi 0x00000000 0x00100000 2 2 0 jedec_probe
\ No newline at end of file diff --git a/src/tcl/target/smp8634.cfg b/src/tcl/target/smp8634.cfg deleted file mode 100644 index c1d61882..00000000 --- a/src/tcl/target/smp8634.cfg +++ /dev/null @@ -1,32 +0,0 @@ -# script for Sigma Designs SMP8634 (eventually even SMP8635) - -if { [info exists CHIPNAME] } { - set _CHIPNAME $CHIPNAME -} else { - set _CHIPNAME smp8634 -} - -if { [info exists ENDIAN] } { - set _ENDIAN $ENDIAN -} else { - set _ENDIAN little -} - -if { [info exists CPUTAPID ] } { - set _CPUTAPID $CPUTAPID -} else { - # force an error till we get a good number - set _CPUTAPID 0x08630001 -} - -jtag_nsrst_delay 100 -jtag_ntrst_delay 100 - -reset_config trst_and_srst separate - -# jtag scan chain -# format L IRC IRCM IDCODE (Length, IR Capture, IR Capture Mask, IDCODE) -jtag newtap $_CHIPNAME cpu -irlen 5 -ircapture 0x1 -irmask 0x1 - -set _TARGETNAME [format "%s.cpu" $_CHIPNAME] -target create $_TARGETNAME mips_m4k -endian $_ENDIAN -variant diff --git a/src/tcl/target/stm32.cfg b/src/tcl/target/stm32.cfg deleted file mode 100644 index 2fe17850..00000000 --- a/src/tcl/target/stm32.cfg +++ /dev/null @@ -1,58 +0,0 @@ -# script for stm32 - -if { [info exists CHIPNAME] } { - set _CHIPNAME $CHIPNAME -} else { - set _CHIPNAME stm32 -} - -if { [info exists ENDIAN] } { - set _ENDIAN $ENDIAN -} else { - set _ENDIAN little -} - -# jtag speed -jtag_khz 500 - -jtag_nsrst_delay 100 -jtag_ntrst_delay 100 - -#use combined on interfaces or targets that can't set TRST/SRST separately -reset_config trst_and_srst - -#jtag scan chain -if { [info exists CPUTAPID ] } { - set _CPUTAPID $CPUTAPID -} else { - # See STM Document RM0008 - # Section 26.6.3 - set _CPUTAPID 0x3ba00477 -} -jtag newtap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_CPUTAPID - -if { [info exists BSTAPID ] } { - set _BSTAPID $BSTAPID -} else { - # See STM Document RM0008 - # Section 26.6.2 - # Low density devices, Rev A - set _BSTAPID1 0x06412041 - # Medium density devices, Rev A - set _BSTAPID2 0x06410041 - # Medium density devices, Rev B and Rev Z - set _BSTAPID3 0x16410041 - # High density devices, Rev A - set _BSTAPID4 0x06414041 -} -jtag newtap $_CHIPNAME bs -irlen 5 -ircapture 0x1 -irmask 0x1 -expected-id $_BSTAPID1 -expected-id $_BSTAPID2 -expected-id $_BSTAPID3 -expected-id $_BSTAPID4 - -set _TARGETNAME [format "%s.cpu" $_CHIPNAME] -target create $_TARGETNAME cortex_m3 -endian $_ENDIAN -chain-position $_TARGETNAME - -$_TARGETNAME configure -work-area-virt 0 -work-area-phys 0x20000000 -work-area-size 16384 -work-area-backup 0 - -flash bank stm32x 0 0 0 0 0 - -# For more information about the configuration files, take a look at: -# openocd.texi diff --git a/src/tcl/target/str710.cfg b/src/tcl/target/str710.cfg deleted file mode 100644 index 2d9d2fc4..00000000 --- a/src/tcl/target/str710.cfg +++ /dev/null @@ -1,45 +0,0 @@ -#start slow, speed up after reset -jtag_khz 10 - -if { [info exists CHIPNAME] } { - set _CHIPNAME $CHIPNAME -} else { - set _CHIPNAME str710 -} - -if { [info exists ENDIAN] } { - set _ENDIAN $ENDIAN -} else { - set _ENDIAN little -} - -if { [info exists CPUTAPID] } { - set _CPUTAPID $CPUTAPID -} else { - set _CPUTAPID 0x3f0f0f0f -} - -#use combined on interfaces or targets that can't set TRST/SRST separately -reset_config trst_and_srst srst_pulls_trst - -#jtag scan chain - -jtag newtap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0x0f -expected-id $_CPUTAPID - -set _TARGETNAME [format "%s.cpu" $_CHIPNAME] -target create $_TARGETNAME arm7tdmi -endian $_ENDIAN -chain-position $_TARGETNAME -variant arm7tdmi -$_TARGETNAME configure -event reset-start { jtag_khz 10 } -$_TARGETNAME configure -event reset-init { jtag_khz 6000 } -$_TARGETNAME configure -event gdb-flash-erase-start { - flash protect 0 0 7 off - flash protect 1 0 1 off -} - -$_TARGETNAME configure -work-area-virt 0 -work-area-phys 0x2000C000 -work-area-size 0x4000 -work-area-backup 0 - -#flash bank str7x <base> <size> 0 0 <target#> <variant> -flash bank str7x 0x40000000 0x00040000 0 0 0 STR71x -flash bank str7x 0x400C0000 0x00004000 0 0 0 STR71x - -# For more information about the configuration files, take a look at: -# openocd.texi diff --git a/src/tcl/target/str730.cfg b/src/tcl/target/str730.cfg deleted file mode 100644 index 5d01ec71..00000000 --- a/src/tcl/target/str730.cfg +++ /dev/null @@ -1,46 +0,0 @@ -#STR730 CPU - -jtag_khz 3000 - -if { [info exists CHIPNAME] } { - set _CHIPNAME $CHIPNAME -} else { - set _CHIPNAME str730 -} - -if { [info exists ENDIAN] } { - set _ENDIAN $ENDIAN -} else { - set _ENDIAN little -} - -if { [info exists CPUTAPID] } { - set _CPUTAPID $CPUTAPID -} else { - set _CPUTAPID 0x3f0f0f0f -} - -#use combined on interfaces or targets that can't set TRST/SRST separately -#reset_config trst_and_srst srst_pulls_trst -reset_config trst_and_srst srst_pulls_trst - -#jtag scan chain -jtag newtap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0x0f -expected-id $_CPUTAPID - -#jtag nTRST and nSRST delay -jtag_nsrst_delay 500 -jtag_ntrst_delay 500 - -set _TARGETNAME [format "%s.cpu" $_CHIPNAME] -target create $_TARGETNAME arm7tdmi -endian little -chain-position 0 -variant arm7tdmi -$_TARGETNAME configure -event reset-start { jtag_khz 10 } -$_TARGETNAME configure -event reset-init { jtag_khz 3000 } -$_TARGETNAME configure -event gdb-flash-erase-start { - flash protect 0 0 7 off -} - -$_TARGETNAME configure -work-area-virt 0 -work-area-phys 0x40000000 -work-area-size 0x4000 -work-area-backup 0 - -#flash bank <driver> <base> <size> <chip_width> <bus_width> -flash bank str7x 0x20000000 0x00040000 0 0 0 STR3x - diff --git a/src/tcl/target/str750.cfg b/src/tcl/target/str750.cfg deleted file mode 100644 index 6b5e66c3..00000000 --- a/src/tcl/target/str750.cfg +++ /dev/null @@ -1,51 +0,0 @@ -#STR750 CPU - -if { [info exists CHIPNAME] } { - set _CHIPNAME $CHIPNAME -} else { - set _CHIPNAME str750 -} - -if { [info exists ENDIAN] } { - set _ENDIAN $ENDIAN -} else { - set _ENDIAN little -} - -if { [info exists CPUTAPID] } { - set _CPUTAPID $CPUTAPID -} else { - set _CPUTAPID 0x4f1f0041 -} - -# jtag speed -jtag_khz 10 - -#use combined on interfaces or targets that can't set TRST/SRST separately -#reset_config trst_and_srst srst_pulls_trst -reset_config trst_and_srst srst_pulls_trst - -#jtag scan chain - -jtag newtap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0x0f -expected-id $_CPUTAPID - -#jtag nTRST and nSRST delay -jtag_nsrst_delay 500 -jtag_ntrst_delay 500 - -set _TARGETNAME [format "%s.cpu" $_CHIPNAME] -target create $_TARGETNAME arm7tdmi -endian little -chain-position 0 -variant arm7tdmi - -$_TARGETNAME configure -event reset-start { jtag_khz 10 } -$_TARGETNAME configure -event reset-init { jtag_khz 3000 } -$_TARGETNAME configure -event gdb-flash-erase-start { - flash protect 0 0 7 off - flash protect 1 0 1 off -} - -$_TARGETNAME configure -work-area-virt 0 -work-area-phys 0x40000000 -work-area-size 0x4000 -work-area-backup 0 - -#flash bank <driver> <base> <size> <chip_width> <bus_width> -flash bank str7x 0x20000000 0x00040000 0 0 0 STR75x -flash bank str7x 0x200C0000 0x00004000 0 0 0 STR75x - diff --git a/src/tcl/target/str912.cfg b/src/tcl/target/str912.cfg deleted file mode 100644 index 705326b5..00000000 --- a/src/tcl/target/str912.cfg +++ /dev/null @@ -1,70 +0,0 @@ -# script for str9 - -if { [info exists CHIPNAME] } { - set _CHIPNAME $CHIPNAME -} else { - set _CHIPNAME str912 -} - -if { [info exists ENDIAN] } { - set _ENDIAN $ENDIAN -} else { - set _ENDIAN little -} - -# jtag speed. We need to stick to 16kHz until we've finished reset. -jtag_rclk 16 - -jtag_nsrst_delay 100 -jtag_ntrst_delay 100 - -#use combined on interfaces or targets that can't set TRST/SRST separately -reset_config trst_and_srst - -if { [info exists FLASHTAPID ] } { - set _FLASHTAPID $FLASHTAPID -} else { - set _FLASHTAPID 0x04570041 -} -jtag newtap $_CHIPNAME flash -irlen 8 -ircapture 0x1 -irmask 0x1 -expected-id $_FLASHTAPID - -if { [info exists CPUTAPID ] } { - set _CPUTAPID $CPUTAPID -} else { - set _CPUTAPID 0x25966041 -} -jtag newtap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_CPUTAPID - - -if { [info exists BSTAPID ] } { - set _BSTAPID $BSTAPID -} else { - set _BSTAPID 0x1457f041 -} -jtag newtap $_CHIPNAME bs -irlen 5 -ircapture 0x1 -irmask 0x1 -expected-id $_BSTAPID - -set _TARGETNAME [format "%s.cpu" $_CHIPNAME] -target create $_TARGETNAME arm966e -endian $_ENDIAN -chain-position $_TARGETNAME -variant arm966e - -$_TARGETNAME configure -event reset-start { jtag_rclk 16 } - -$_TARGETNAME configure -event reset-init { - # We can increase speed now that we know the target is halted. - #jtag_rclk 3000 - - # -- Enable 96K RAM - # PFQBC enabled / DTCM & AHB wait-states disabled - mww 0x5C002034 0x0191 - - str9x flash_config 0 4 2 0 0x80000 - flash protect 0 0 7 off -} - -$_TARGETNAME configure -work-area-virt 0 -work-area-phys 0x50000000 -work-area-size 16384 -work-area-backup 0 - -#flash bank str9x <base> <size> 0 0 <target#> <variant> -flash bank str9x 0x00000000 0x00080000 0 0 0 -flash bank str9x 0x00080000 0x00008000 0 0 0 - -# For more information about the configuration files, take a look at: -# openocd.texi diff --git a/src/tcl/target/test_reset_syntax_error.cfg b/src/tcl/target/test_reset_syntax_error.cfg deleted file mode 100644 index e573c1c0..00000000 --- a/src/tcl/target/test_reset_syntax_error.cfg +++ /dev/null @@ -1,17 +0,0 @@ -# Test script to check that syntax error in reset -# script is reported properly. - -# at91eb40a target - -#jtag scan chain -set _CHIPNAME syntaxtest -jtag newtap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0xf - -#target configuration -set _TARGETNAME [format "%s.cpu" $_CHIPNAME] -target create $_TARGETNAME arm7tdmi -endian $_ENDIAN -chain-position $_TARGETNAME -variant arm7tdmi-s_r4 - -$_TARGETNAME configure -event reset-init { - - syntax error -} diff --git a/src/tcl/target/test_syntax_error.cfg b/src/tcl/target/test_syntax_error.cfg deleted file mode 100644 index 8727aa36..00000000 --- a/src/tcl/target/test_syntax_error.cfg +++ /dev/null @@ -1,4 +0,0 @@ -# This script tests a syntax error in the startup -# config script - -syntax error here diff --git a/src/tcl/target/ti_dm355.cfg b/src/tcl/target/ti_dm355.cfg deleted file mode 100644 index 1bd5cda5..00000000 --- a/src/tcl/target/ti_dm355.cfg +++ /dev/null @@ -1,92 +0,0 @@ -# -# Texas Instruments DaVinci family: TMS320DM355 -# -if { [info exists CHIPNAME] } { - set _CHIPNAME $CHIPNAME -} else { - set _CHIPNAME dm355 -} -if { [info exists ENDIAN] } { - set _ENDIAN $ENDIAN -} else { - set _ENDIAN little -} - -# -# For now, expect EMU0/EMU1 jumpered LOW (not TI's default) so ARM and ETB -# are enabled without making ICEpick route ARM and ETB into the JTAG chain. -# -# Also note: when running without RTCK before the PLLs are set up, you -# may need to slow the JTAG clock down quite a lot (under 2 MHz). -# - -# Subsidiary TAP: ARM ETB11, with scan chain for 4K of ETM trace buffer -if { [info exists ETB_TAPID ] } { - set _ETB_TAPID $ETB_TAPID -} else { - set _ETB_TAPID 0x2b900f0f -} -jtag newtap $_CHIPNAME etb -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_ETB_TAPID - -# Subsidiary TAP: ARM926ejs with scan chains for ARM Debug, EmbeddedICE-RT, ETM. -if { [info exists CPU_TAPID ] } { - set _CPU_TAPID $CPU_TAPID -} else { - set _CPU_TAPID 0x07926001 -} -jtag newtap $_CHIPNAME arm -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_CPU_TAPID - -# Primary TAP: ICEpick (JTAG route controller) and boundary scan -if { [info exists JRC_TAPID ] } { - set _JRC_TAPID $JRC_TAPID -} else { - set _JRC_TAPID 0x0b73b02f -} -jtag newtap $_CHIPNAME jrc -irlen 6 -ircapture 0x1 -irmask 0x3f -expected-id $_JRC_TAPID - -################ - -# various symbol definitions, to avoid hard-wiring addresses -# and enable some sharing of DaVinci-family utility code -global dm355 -set dm355 [ dict create ] - -# Physical addresses for controllers and memory -# (Some of these are valid for many DaVinci family chips) -dict set dm355 sram0 0x00010000 -dict set dm355 sram1 0x00014000 -dict set dm355 sysbase 0x01c40000 -dict set dm355 pllc1 0x01c40800 -dict set dm355 pllc2 0x01c40c00 -dict set dm355 psc 0x01c41000 -dict set dm355 gpio 0x01c67000 -dict set dm355 a_emif 0x01e10000 -dict set dm355 a_emif_cs0 0x02000000 -dict set dm355 a_emif_cs1 0x04000000 -dict set dm355 ddr_emif 0x20000000 -dict set dm355 ddr 0x80000000 - -source [find target/davinci.cfg] - -################ -# GDB target: the ARM, using SRAM1 for scratch. SRAM0 (also 16K) -# and the ETB memory (4K) are other options, while trace is unused. -set _TARGETNAME $_CHIPNAME.arm - -target create $_TARGETNAME arm926ejs -endian $_ENDIAN -chain-position $_TARGETNAME - -# NOTE that work-area-virt presumes a Linux 2.6.30-rc2+ kernel, -# and that the work area is used only with a kernel mmu context ... -$_TARGETNAME configure \ - -work-area-virt [expr 0xfffe0000 + 0x4000] \ - -work-area-phys [dict get $dm355 sram1] \ - -work-area-size 0x4000 \ - -work-area-backup 0 - -arm7_9 dbgrq enable -arm7_9 fast_memory_access enable -arm7_9 dcc_downloads enable - -# trace setup -etm config $_TARGETNAME 16 normal full etb -etb config $_TARGETNAME $_CHIPNAME.etb diff --git a/src/tcl/target/ti_dm6446.cfg b/src/tcl/target/ti_dm6446.cfg deleted file mode 100644 index 68a7c207..00000000 --- a/src/tcl/target/ti_dm6446.cfg +++ /dev/null @@ -1,66 +0,0 @@ -# -# Texas Instruments DaVinci family: TMS320DM6446 -# -if { [info exists CHIPNAME] } { - set _CHIPNAME $CHIPNAME -} else { - set _CHIPNAME dm6446 -} -if { [info exists ENDIAN] } { - set _ENDIAN $ENDIAN -} else { - set _ENDIAN little -} - -# -# For now, expect EMU0/EMU1 jumpered LOW (not TI's default) so ARM and ETB -# are enabled without making ICEpick route ARM and ETB into the JTAG chain. -# -# Also note: when running without RTCK before the PLLs are set up, you -# may need to slow the JTAG clock down quite a lot (under 2 MHz). -# - -# Subsidiary TAP: ARM ETB11, with scan chain for 4K of ETM trace buffer -if { [info exists ETB_TAPID ] } { - set _ETB_TAPID $ETB_TAPID -} else { - set _ETB_TAPID 0x2b900f0f -} -jtag newtap $_CHIPNAME etb -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_ETB_TAPID - -# Subsidiary TAP: ARM926ejs with scan chains for ARM Debug, EmbeddedICE-RT, ETM. -if { [info exists CPU_TAPID ] } { - set _CPU_TAPID $CPU_TAPID -} else { - set _CPU_TAPID 0x07926001 -} -jtag newtap $_CHIPNAME arm -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_CPU_TAPID - -# Subsidiary TAP: C64x+ DSP ... NOT CURRENTLY INCLUDED, must add via ICEpick. -# Documentation for DSP JTAG interfaces evidently needs NDAs. - -# Primary TAP: ICEpick (JTAG route controller) and boundary scan -if { [info exists JRC_TAPID ] } { - set _JRC_TAPID $JRC_TAPID -} else { - set _JRC_TAPID 0x0b70002f -} -jtag newtap $_CHIPNAME jrc -irlen 6 -ircapture 0x1 -irmask 0x3f -expected-id $_JRC_TAPID - -# GDB target: the ARM, using SRAM1 for scratch. SRAM0 (also 8K) -# and the ETB memory (4K) are other options, while trace is unused. -set _TARGETNAME $_CHIPNAME.arm - -target create $_TARGETNAME arm926ejs -endian $_ENDIAN -chain-position $_TARGETNAME -$_TARGETNAME configure -work-area-virt 0 -work-area-phys 0x0000a000 -work-area-size 0x2000 -work-area-backup 0 - -arm7_9 dbgrq enable -arm7_9 fast_memory_access enable -arm7_9 dcc_downloads enable - -# trace setup -# FIXME we ought to be able to say "... config $_TARGETNAME ..." -# (not "config 0") facilitating additional targets (e.g. other chips) -etm config 0 16 normal full etb -etb config 0 $_CHIPNAME.etb - diff --git a/src/tcl/target/xba_revA3.cfg b/src/tcl/target/xba_revA3.cfg deleted file mode 100644 index 007cb9e1..00000000 --- a/src/tcl/target/xba_revA3.cfg +++ /dev/null @@ -1,86 +0,0 @@ -#Written by: Michael Schwingen <rincewind@discworld.dascon.de> - -if { [info exists CHIPNAME] } { - set _CHIPNAME $CHIPNAME -} else { - set _CHIPNAME xba_reva3 -} - -if { [info exists ENDIAN] } { - set _ENDIAN $ENDIAN -} else { - # default to big endian - set _ENDIAN big -} - -if { [info exists CPUTAPID ] } { - set _CPUTAPID $CPUTAPID -} else { - # force an error till we get a good number - set _CPUTAPID 0xffffffff -} - -reset_config trst_and_srst separate - -jtag_nsrst_delay 100 -jtag_ntrst_delay 100 - -#jtag scan chain -jtag newtap $_CHIPNAME cpu -irlen 7 -ircapture 0x1 -irmask 0x7f -expected-id $_CPUTAPID - -set _TARGETNAME [format "%s.cpu" $_CHIPNAME] -target create $_TARGETNAME xscale -endian $_ENDIAN -chain-position $_TARGETNAME -variant ixp42x -$_TARGETNAME configure -event reset-init { - ############################################################################# - # setup expansion bus CS, disable external wdt - ############################################################################# - mww 0xc4000000 0xbd113842 #CS0 : Flash, write enabled @0x50000000 - mww 0xc4000004 0x94d10013 #CS1 - mww 0xc4000008 0x95960003 #CS2 - mww 0xc400000c 0x00000000 #CS3 - mww 0xc4000010 0x80900003 #CS4 - mww 0xc4000014 0x9d520003 #CS5 - mww 0xc4000018 0x81860001 #CS6 - mww 0xc400001c 0x80900003 #CS7 - - ############################################################################# - # init SDRAM controller: 16MB, one bank, CL3 - ############################################################################# - mww 0xCC000000 0x2A # SDRAM_CFG: 64MBit, CL3 - mww 0xCC000004 0 # disable refresh - mww 0xCC000008 3 # NOP - sleep 100 - mww 0xCC000004 2100 # set refresh counter - mww 0xCC000008 2 # Precharge All Banks - sleep 100 - mww 0xCC000008 4 # Auto Refresh - mww 0xCC000008 4 # Auto Refresh - mww 0xCC000008 4 # Auto Refresh - mww 0xCC000008 4 # Auto Refresh - mww 0xCC000008 4 # Auto Refresh - mww 0xCC000008 4 # Auto Refresh - mww 0xCC000008 4 # Auto Refresh - mww 0xCC000008 4 # Auto Refresh - mww 0xCC000008 1 # Mode Select CL3 - - #mww 0xc4000020 0xffffee # CFG0: remove expansion bus boot flash - #mirror at 0x00000000 - - #big endian - reg XSCALE_CTRL 0xF8 - - # - # detect flash - # - flash probe 0 -} - -$_TARGETNAME configure -work-area-virt 0 -work-area-phys 0x20010000 -work-area-size 0x8060 -work-area-backup 0 - - -flash bank cfi 0x50000000 0x400000 2 2 0 - -init -reset init -# set big endian mode -reg XSCALE_CTRL 0xF8 |