8 files changed, 9 insertions, 9 deletions
diff --git a/tcl/board/at91sam9g20-ek.cfg b/tcl/board/at91sam9g20-ek.cfg
index 00ab7faf..6e8a1934 100644
--- a/tcl/board/at91sam9g20-ek.cfg
+++ b/tcl/board/at91sam9g20-ek.cfg
@@ -41,8 +41,8 @@ target create $_TARGETNAME arm926ejs -endian $_ENDIAN -chain-position $_TARGETNA
 # AT91SAM9G20 has two SRAM areas, one starting at 0x00200000 and the other starting at 0x00300000.
 # Both areas are 16 kB long.
 
-$_TARGETNAME configure -work-area-virt 0 -work-area-phys 0x00200000 -work-area-size 0x4000 -work-area-backup 1
-$_TARGETNAME configure -work-area-virt 0 -work-area-phys 0x00300000 -work-area-size 0x4000 -work-area-backup 1
+#$_TARGETNAME configure -work-area-phys 0x00200000 -work-area-size 0x4000 -work-area-backup 1
+$_TARGETNAME configure -work-area-phys 0x00300000 -work-area-size 0x4000 -work-area-backup 1
 
 # If you don't want to execute built-in boot rom code (and there are good reasons at times not to do that) in the
 # AT91SAM9 family, the microcontroller is a lump on a log without initialization.  Because this family has
diff --git a/tcl/board/digi_connectcore_wi-9c.cfg b/tcl/board/digi_connectcore_wi-9c.cfg
index 58f12a68..e6d17bdd 100644
--- a/tcl/board/digi_connectcore_wi-9c.cfg
+++ b/tcl/board/digi_connectcore_wi-9c.cfg
@@ -114,7 +114,7 @@ $_TARGETNAME configure -event reset-init {
 	reg cpsr 0xd3
 }
 
-$_TARGETNAME configure -work-area-virt 0 -work-area-phys 0x00000000 -work-area-size 0x1000 -work-area-backup 1
+$_TARGETNAME configure -work-area-phys 0x00000000 -work-area-size 0x1000 -work-area-backup 1
 
 #####################
 # Flash configuration
diff --git a/tcl/board/hitex_str9-comstick.cfg b/tcl/board/hitex_str9-comstick.cfg
index 25ff784d..e7b79616 100644
--- a/tcl/board/hitex_str9-comstick.cfg
+++ b/tcl/board/hitex_str9-comstick.cfg
@@ -65,7 +65,7 @@ $_TARGETNAME configure -event reset-init {
 	flash protect 0 0 7 off
 }
 
-$_TARGETNAME configure -work-area-virt 0 -work-area-phys 0x50000000 -work-area-size 16384 -work-area-backup 0
+$_TARGETNAME configure -work-area-phys 0x50000000 -work-area-size 16384 -work-area-backup 0
 
 #flash bank <driver> <base> <size> <chip_width> <bus_width>
 flash bank str9x 0x00000000 0x00080000 0 0 0
diff --git a/tcl/board/linksys_nslu2.cfg b/tcl/board/linksys_nslu2.cfg
index 52984107..e605fc19 100644
--- a/tcl/board/linksys_nslu2.cfg
+++ b/tcl/board/linksys_nslu2.cfg
@@ -4,5 +4,5 @@
 source [find target/ixp42x.cfg]
 # The _TARGETNAME is set by the above.
 
-$_TARGETNAME configure -work-area-virt 0 -work-area-phys 0x00020000 -work-area-size 0x10000 -work-area-backup 0
+$_TARGETNAME configure -work-area-phys 0x00020000 -work-area-size 0x10000 -work-area-backup 0
 
diff --git a/tcl/board/mini2440.cfg b/tcl/board/mini2440.cfg
index 90acafa0..d17b1076 100644
--- a/tcl/board/mini2440.cfg
+++ b/tcl/board/mini2440.cfg
@@ -104,7 +104,7 @@ jtag newtap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0x0f -expected-id $_C
 
 set _TARGETNAME [format "%s.cpu" $_CHIPNAME]
 target create $_TARGETNAME arm920t -endian $_ENDIAN -chain-position $_TARGETNAME -variant arm920t
-$_TARGETNAME configure -work-area-virt 0 -work-area-phys 0x40000000  -work-area-size 0x4000 -work-area-backup 1
+$_TARGETNAME configure -work-area-phys 0x40000000  -work-area-size 0x4000 -work-area-backup 1
 
 #reset configuration
 jtag_nsrst_delay 100
diff --git a/tcl/board/pxa255_sst.cfg b/tcl/board/pxa255_sst.cfg
index d9f6187b..8bc691ba 100644
--- a/tcl/board/pxa255_sst.cfg
+++ b/tcl/board/pxa255_sst.cfg
@@ -10,7 +10,7 @@
 source [find target/pxa255.cfg]
 
 # Target name is set by above
-$_TARGETNAME configure -work-area-virt 0 -work-area-phys 0x4000000 -work-area-size 0x4000 -work-area-backup 0
+$_TARGETNAME configure -work-area-phys 0x4000000 -work-area-size 0x4000 -work-area-backup 0
 
 # flash bank <driver> <base> <size> <chip_width> <bus_width> <target> [options]
 flash bank cfi 0x00000000 0x80000 2 2 $_TARGETNAME jedec_probe
diff --git a/tcl/board/str910-eval.cfg b/tcl/board/str910-eval.cfg
index e98c1c74..fa872a9b 100644
--- a/tcl/board/str910-eval.cfg
+++ b/tcl/board/str910-eval.cfg
@@ -39,7 +39,7 @@ jtag newtap $_CHIPNAME bs    -irlen 5 -ircapture 0x1 -irmask 0x1 -expected-id $_
 
 set _TARGETNAME [format "%s.cpu" $_CHIPNAME]
 target create $_TARGETNAME arm966e -endian $_ENDIAN -chain-position $_TARGETNAME -variant arm966e
-$_TARGETNAME configure -work-area-phys 0x50000000 -work-area-virt 0x50000000 -work-area-size 16384 -work-area-backup 1
+$_TARGETNAME configure -work-area-phys 0x50000000 -work-area-size 16384 -work-area-backup 1
 
 $_TARGETNAME configure -event reset-init {
 	# We can increase speed now that we know the target is halted.
diff --git a/tcl/board/zy1000.cfg b/tcl/board/zy1000.cfg
index 2e13ecbb..54bb7bb7 100644
--- a/tcl/board/zy1000.cfg
+++ b/tcl/board/zy1000.cfg
@@ -63,7 +63,7 @@ $_TARGETNAME configure -event reset-init {
 
 # required for usable performance. Used for lots of
 # other things than flash programming.
-$_TARGETNAME configure -work-area-virt 0 -work-area-phys 0x00020000 -work-area-size 0x20000 -work-area-backup 0
+$_TARGETNAME configure -work-area-phys 0x00020000 -work-area-size 0x20000 -work-area-backup 0
 
 jtag_khz 16000