diff options
Diffstat (limited to 'thirdparty/STM32_USB-FS-Device_Lib_V4.0.0/Libraries/STM32F30x_StdPeriph_Driver/src/stm32f30x_i2c.c')
| -rw-r--r-- | thirdparty/STM32_USB-FS-Device_Lib_V4.0.0/Libraries/STM32F30x_StdPeriph_Driver/src/stm32f30x_i2c.c | 1585 |
1 files changed, 1585 insertions, 0 deletions
diff --git a/thirdparty/STM32_USB-FS-Device_Lib_V4.0.0/Libraries/STM32F30x_StdPeriph_Driver/src/stm32f30x_i2c.c b/thirdparty/STM32_USB-FS-Device_Lib_V4.0.0/Libraries/STM32F30x_StdPeriph_Driver/src/stm32f30x_i2c.c new file mode 100644 index 0000000..2d81b08 --- /dev/null +++ b/thirdparty/STM32_USB-FS-Device_Lib_V4.0.0/Libraries/STM32F30x_StdPeriph_Driver/src/stm32f30x_i2c.c @@ -0,0 +1,1585 @@ +/** + ****************************************************************************** + * @file stm32f30x_i2c.c + * @author MCD Application Team + * @version V1.0.1 + * @date 23-October-2012 + * @brief This file provides firmware functions to manage the following + * functionalities of the Inter-Integrated circuit (I2C): + * + Initialization and Configuration + * + Communications handling + * + SMBUS management + * + I2C registers management + * + Data transfers management + * + DMA transfers management + * + Interrupts and flags management + * + * @verbatim + ============================================================================ + ##### How to use this driver ##### + ============================================================================ + [..] + (#) Enable peripheral clock using RCC_APB1PeriphClockCmd(RCC_APB1Periph_I2Cx, ENABLE) + function for I2C1 or I2C2. + (#) Enable SDA, SCL and SMBA (when used) GPIO clocks using + RCC_AHBPeriphClockCmd() function. + (#) Peripherals alternate function: + (++) Connect the pin to the desired peripherals' Alternate + Function (AF) using GPIO_PinAFConfig() function. + (++) Configure the desired pin in alternate function by: + GPIO_InitStruct->GPIO_Mode = GPIO_Mode_AF + (++) Select the type, OpenDrain and speed via + GPIO_PuPd, GPIO_OType and GPIO_Speed members + (++) Call GPIO_Init() function. + (#) Program the Mode, Timing , Own address, Ack and Acknowledged Address + using the I2C_Init() function. + (#) Optionally you can enable/configure the following parameters without + re-initialization (i.e there is no need to call again I2C_Init() function): + (++) Enable the acknowledge feature using I2C_AcknowledgeConfig() function. + (++) Enable the dual addressing mode using I2C_DualAddressCmd() function. + (++) Enable the general call using the I2C_GeneralCallCmd() function. + (++) Enable the clock stretching using I2C_StretchClockCmd() function. + (++) Enable the PEC Calculation using I2C_CalculatePEC() function. + (++) For SMBus Mode: + (+++) Enable the SMBusAlert pin using I2C_SMBusAlertCmd() function. + (#) Enable the NVIC and the corresponding interrupt using the function + I2C_ITConfig() if you need to use interrupt mode. + (#) When using the DMA mode + (++) Configure the DMA using DMA_Init() function. + (++) Active the needed channel Request using I2C_DMACmd() function. + (#) Enable the I2C using the I2C_Cmd() function. + (#) Enable the DMA using the DMA_Cmd() function when using DMA mode in the + transfers. + [..] + (@) When using I2C in Fast Mode Plus, SCL and SDA pin 20mA current drive capability + must be enabled by setting the driving capability control bit in SYSCFG. + + @endverbatim + ****************************************************************************** + * @attention + * + * <h2><center>© COPYRIGHT 2012 STMicroelectronics</center></h2> + * + * Licensed under MCD-ST Liberty SW License Agreement V2, (the "License"); + * You may not use this file except in compliance with the License. + * You may obtain a copy of the License at: + * + * http://www.st.com/software_license_agreement_liberty_v2 + * + * Unless required by applicable law or agreed to in writing, software + * distributed under the License is distributed on an "AS IS" BASIS, + * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. + * See the License for the specific language governing permissions and + * limitations under the License. + * + ****************************************************************************** + */ + +/* Includes ------------------------------------------------------------------*/ +#include "stm32f30x_i2c.h" +#include "stm32f30x_rcc.h" + +/** @addtogroup STM32F30x_StdPeriph_Driver + * @{ + */ + +/** @defgroup I2C + * @brief I2C driver modules + * @{ + */ + +/* Private typedef -----------------------------------------------------------*/ +/* Private define ------------------------------------------------------------*/ + +#define CR1_CLEAR_MASK ((uint32_t)0x00CFE0FF) /*<! I2C CR1 clear register Mask */ +#define CR2_CLEAR_MASK ((uint32_t)0x07FF7FFF) /*<! I2C CR2 clear register Mask */ +#define TIMING_CLEAR_MASK ((uint32_t)0xF0FFFFFF) /*<! I2C TIMING clear register Mask */ +#define ERROR_IT_MASK ((uint32_t)0x00003F00) /*<! I2C Error interrupt register Mask */ +#define TC_IT_MASK ((uint32_t)0x000000C0) /*<! I2C TC interrupt register Mask */ + +/* Private macro -------------------------------------------------------------*/ +/* Private variables ---------------------------------------------------------*/ +/* Private function prototypes -----------------------------------------------*/ +/* Private functions ---------------------------------------------------------*/ + +/** @defgroup I2C_Private_Functions + * @{ + */ + + +/** @defgroup I2C_Group1 Initialization and Configuration functions + * @brief Initialization and Configuration functions + * +@verbatim + =============================================================================== + ##### Initialization and Configuration functions ##### + =============================================================================== + [..] This section provides a set of functions allowing to initialize the I2C Mode, + I2C Timing, I2C filters, I2C Addressing mode, I2C OwnAddress1. + + [..] The I2C_Init() function follows the I2C configuration procedures (these procedures + are available in reference manual). + + [..] When the Software Reset is performed using I2C_SoftwareResetCmd() function, the internal + states machines are reset and communication control bits, as well as status bits come + back to their reset value. + + [..] Before enabling Stop mode using I2C_StopModeCmd() I2C Clock source must be set to + HSI and Digital filters must be disabled. + + [..] Before enabling Own Address 2 via I2C_DualAddressCmd() function, OA2 and mask should be + configured using I2C_OwnAddress2Config() function. + + [..] I2C_SlaveByteControlCmd() enable Slave byte control that allow user to get control of + each byte in slave mode when NBYTES is set to 0x01. + +@endverbatim + * @{ + */ + +/** + * @brief Deinitializes the I2Cx peripheral registers to their default reset values. + * @param I2Cx: where x can be 1 or 2 to select the I2C peripheral. + * @retval None + */ +void I2C_DeInit(I2C_TypeDef* I2Cx) +{ + /* Check the parameters */ + assert_param(IS_I2C_ALL_PERIPH(I2Cx)); + + if (I2Cx == I2C1) + { + /* Enable I2C1 reset state */ + RCC_APB1PeriphResetCmd(RCC_APB1Periph_I2C1, ENABLE); + /* Release I2C1 from reset state */ + RCC_APB1PeriphResetCmd(RCC_APB1Periph_I2C1, DISABLE); + } + else + { + /* Enable I2C2 reset state */ + RCC_APB1PeriphResetCmd(RCC_APB1Periph_I2C2, ENABLE); + /* Release I2C2 from reset state */ + RCC_APB1PeriphResetCmd(RCC_APB1Periph_I2C2, DISABLE); + } +} + +/** + * @brief Initializes the I2Cx peripheral according to the specified + * parameters in the I2C_InitStruct. + * @param I2Cx: where x can be 1 or 2 to select the I2C peripheral. + * @param I2C_InitStruct: pointer to a I2C_InitTypeDef structure that + * contains the configuration information for the specified I2C peripheral. + * @retval None + */ +void I2C_Init(I2C_TypeDef* I2Cx, I2C_InitTypeDef* I2C_InitStruct) +{ + uint32_t tmpreg = 0; + + /* Check the parameters */ + assert_param(IS_I2C_ALL_PERIPH(I2Cx)); + assert_param(IS_I2C_ANALOG_FILTER(I2C_InitStruct->I2C_AnalogFilter)); + assert_param(IS_I2C_DIGITAL_FILTER(I2C_InitStruct->I2C_DigitalFilter)); + assert_param(IS_I2C_MODE(I2C_InitStruct->I2C_Mode)); + assert_param(IS_I2C_OWN_ADDRESS1(I2C_InitStruct->I2C_OwnAddress1)); + assert_param(IS_I2C_ACK(I2C_InitStruct->I2C_Ack)); + assert_param(IS_I2C_ACKNOWLEDGE_ADDRESS(I2C_InitStruct->I2C_AcknowledgedAddress)); + + /* Disable I2Cx Peripheral */ + I2Cx->CR1 &= (uint32_t)~((uint32_t)I2C_CR1_PE); + + /*---------------------------- I2Cx FILTERS Configuration ------------------*/ + /* Get the I2Cx CR1 value */ + tmpreg = I2Cx->CR1; + /* Clear I2Cx CR1 register */ + tmpreg &= CR1_CLEAR_MASK; + /* Configure I2Cx: analog and digital filter */ + /* Set ANFOFF bit according to I2C_AnalogFilter value */ + /* Set DFN bits according to I2C_DigitalFilter value */ + tmpreg |= (uint32_t)I2C_InitStruct->I2C_AnalogFilter |(I2C_InitStruct->I2C_DigitalFilter << 8); + + /* Write to I2Cx CR1 */ + I2Cx->CR1 = tmpreg; + + /*---------------------------- I2Cx TIMING Configuration -------------------*/ + /* Configure I2Cx: Timing */ + /* Set TIMINGR bits according to I2C_Timing */ + /* Write to I2Cx TIMING */ + I2Cx->TIMINGR = I2C_InitStruct->I2C_Timing & TIMING_CLEAR_MASK; + + /* Enable I2Cx Peripheral */ + I2Cx->CR1 |= I2C_CR1_PE; + + /*---------------------------- I2Cx OAR1 Configuration ---------------------*/ + /* Clear tmpreg local variable */ + tmpreg = 0; + /* Clear OAR1 register */ + I2Cx->OAR1 = (uint32_t)tmpreg; + /* Clear OAR2 register */ + I2Cx->OAR2 = (uint32_t)tmpreg; + /* Configure I2Cx: Own Address1 and acknowledged address */ + /* Set OA1MODE bit according to I2C_AcknowledgedAddress value */ + /* Set OA1 bits according to I2C_OwnAddress1 value */ + tmpreg = (uint32_t)((uint32_t)I2C_InitStruct->I2C_AcknowledgedAddress | \ + (uint32_t)I2C_InitStruct->I2C_OwnAddress1); + /* Write to I2Cx OAR1 */ + I2Cx->OAR1 = tmpreg; + /* Enable Own Address1 acknowledgement */ + I2Cx->OAR1 |= I2C_OAR1_OA1EN; + + /*---------------------------- I2Cx MODE Configuration ---------------------*/ + /* Configure I2Cx: mode */ + /* Set SMBDEN and SMBHEN bits according to I2C_Mode value */ + tmpreg = I2C_InitStruct->I2C_Mode; + /* Write to I2Cx CR1 */ + I2Cx->CR1 |= tmpreg; + + /*---------------------------- I2Cx ACK Configuration ----------------------*/ + /* Get the I2Cx CR2 value */ + tmpreg = I2Cx->CR2; + /* Clear I2Cx CR2 register */ + tmpreg &= CR2_CLEAR_MASK; + /* Configure I2Cx: acknowledgement */ + /* Set NACK bit according to I2C_Ack value */ + tmpreg |= I2C_InitStruct->I2C_Ack; + /* Write to I2Cx CR2 */ + I2Cx->CR2 = tmpreg; +} + +/** + * @brief Fills each I2C_InitStruct member with its default value. + * @param I2C_InitStruct: pointer to an I2C_InitTypeDef structure which will be initialized. + * @retval None + */ +void I2C_StructInit(I2C_InitTypeDef* I2C_InitStruct) +{ + /*---------------- Reset I2C init structure parameters values --------------*/ + /* Initialize the I2C_Timing member */ + I2C_InitStruct->I2C_Timing = 0; + /* Initialize the I2C_AnalogFilter member */ + I2C_InitStruct->I2C_AnalogFilter = I2C_AnalogFilter_Enable; + /* Initialize the I2C_DigitalFilter member */ + I2C_InitStruct->I2C_DigitalFilter = 0; + /* Initialize the I2C_Mode member */ + I2C_InitStruct->I2C_Mode = I2C_Mode_I2C; + /* Initialize the I2C_OwnAddress1 member */ + I2C_InitStruct->I2C_OwnAddress1 = 0; + /* Initialize the I2C_Ack member */ + I2C_InitStruct->I2C_Ack = I2C_Ack_Disable; + /* Initialize the I2C_AcknowledgedAddress member */ + I2C_InitStruct->I2C_AcknowledgedAddress = I2C_AcknowledgedAddress_7bit; +} + +/** + * @brief Enables or disables the specified I2C peripheral. + * @param I2Cx: where x can be 1 or 2 to select the I2C peripheral. + * @param NewState: new state of the I2Cx peripheral. + * This parameter can be: ENABLE or DISABLE. + * @retval None + */ +void I2C_Cmd(I2C_TypeDef* I2Cx, FunctionalState NewState) +{ + /* Check the parameters */ + assert_param(IS_I2C_ALL_PERIPH(I2Cx)); + assert_param(IS_FUNCTIONAL_STATE(NewState)); + if (NewState != DISABLE) + { + /* Enable the selected I2C peripheral */ + I2Cx->CR1 |= I2C_CR1_PE; + } + else + { + /* Disable the selected I2C peripheral */ + I2Cx->CR1 &= (uint32_t)~((uint32_t)I2C_CR1_PE); + } +} + + +/** + * @brief Enables or disables the specified I2C software reset. + * @param I2Cx: where x can be 1 or 2 to select the I2C peripheral. + * @retval None + */ +void I2C_SoftwareResetCmd(I2C_TypeDef* I2Cx) +{ + /* Check the parameters */ + assert_param(IS_I2C_ALL_PERIPH(I2Cx)); + + /* Disable peripheral */ + I2Cx->CR1 &= (uint32_t)~((uint32_t)I2C_CR1_PE); + + /* Perform a dummy read to delay the disable of peripheral for minimum + 3 APB clock cycles to perform the software reset functionality */ + *(__IO uint32_t *)(uint32_t)I2Cx; + + /* Enable peripheral */ + I2Cx->CR1 |= I2C_CR1_PE; +} + +/** + * @brief Enables or disables the specified I2C interrupts. + * @param I2Cx: where x can be 1 or 2 to select the I2C peripheral. + * @param I2C_IT: specifies the I2C interrupts sources to be enabled or disabled. + * This parameter can be any combination of the following values: + * @arg I2C_IT_ERRI: Error interrupt mask + * @arg I2C_IT_TCI: Transfer Complete interrupt mask + * @arg I2C_IT_STOPI: Stop Detection interrupt mask + * @arg I2C_IT_NACKI: Not Acknowledge received interrupt mask + * @arg I2C_IT_ADDRI: Address Match interrupt mask + * @arg I2C_IT_RXI: RX interrupt mask + * @arg I2C_IT_TXI: TX interrupt mask + * @param NewState: new state of the specified I2C interrupts. + * This parameter can be: ENABLE or DISABLE. + * @retval None + */ +void I2C_ITConfig(I2C_TypeDef* I2Cx, uint32_t I2C_IT, FunctionalState NewState) +{ + /* Check the parameters */ + assert_param(IS_I2C_ALL_PERIPH(I2Cx)); + assert_param(IS_FUNCTIONAL_STATE(NewState)); + assert_param(IS_I2C_CONFIG_IT(I2C_IT)); + + if (NewState != DISABLE) + { + /* Enable the selected I2C interrupts */ + I2Cx->CR1 |= I2C_IT; + } + else + { + /* Disable the selected I2C interrupts */ + I2Cx->CR1 &= (uint32_t)~((uint32_t)I2C_IT); + } +} + +/** + * @brief Enables or disables the I2C Clock stretching. + * @param I2Cx: where x can be 1 or 2 to select the I2C peripheral. + * @param NewState: new state of the I2Cx Clock stretching. + * This parameter can be: ENABLE or DISABLE. + * @retval None + */ +void I2C_StretchClockCmd(I2C_TypeDef* I2Cx, FunctionalState NewState) +{ + /* Check the parameters */ + assert_param(IS_I2C_ALL_PERIPH(I2Cx)); + assert_param(IS_FUNCTIONAL_STATE(NewState)); + + if (NewState != DISABLE) + { + /* Enable clock stretching */ + I2Cx->CR1 &= (uint32_t)~((uint32_t)I2C_CR1_NOSTRETCH); + } + else + { + /* Disable clock stretching */ + I2Cx->CR1 |= I2C_CR1_NOSTRETCH; + } +} + +/** + * @brief Enables or disables I2C wakeup from stop mode. + * @param I2Cx: where x can be 1 or 2 to select the I2C peripheral. + * @param NewState: new state of the I2Cx stop mode. + * This parameter can be: ENABLE or DISABLE. + * @retval None + */ +void I2C_StopModeCmd(I2C_TypeDef* I2Cx, FunctionalState NewState) +{ + /* Check the parameters */ + assert_param(IS_I2C_ALL_PERIPH(I2Cx)); + assert_param(IS_FUNCTIONAL_STATE(NewState)); + + if (NewState != DISABLE) + { + /* Enable wakeup from stop mode */ + I2Cx->CR1 |= I2C_CR1_WUPEN; + } + else + { + /* Disable wakeup from stop mode */ + I2Cx->CR1 &= (uint32_t)~((uint32_t)I2C_CR1_WUPEN); + } +} + +/** + * @brief Enables or disables the I2C own address 2. + * @param I2Cx: where x can be 1 or 2 to select the I2C peripheral. + * @param NewState: new state of the I2C own address 2. + * This parameter can be: ENABLE or DISABLE. + * @retval None + */ +void I2C_DualAddressCmd(I2C_TypeDef* I2Cx, FunctionalState NewState) +{ + /* Check the parameters */ + assert_param(IS_I2C_ALL_PERIPH(I2Cx)); + assert_param(IS_FUNCTIONAL_STATE(NewState)); + + if (NewState != DISABLE) + { + /* Enable own address 2 */ + I2Cx->OAR2 |= I2C_OAR2_OA2EN; + } + else + { + /* Disable own address 2 */ + I2Cx->OAR2 &= (uint32_t)~((uint32_t)I2C_OAR2_OA2EN); + } +} + +/** + * @brief Configures the I2C slave own address 2 and mask. + * @param I2Cx: where x can be 1 or 2 to select the I2C peripheral. + * @param Address: specifies the slave address to be programmed. + * @param Mask: specifies own address 2 mask to be programmed. + * This parameter can be one of the following values: + * @arg I2C_OA2_NoMask: no mask. + * @arg I2C_OA2_Mask01: OA2[1] is masked and don't care. + * @arg I2C_OA2_Mask02: OA2[2:1] are masked and don't care. + * @arg I2C_OA2_Mask03: OA2[3:1] are masked and don't care. + * @arg I2C_OA2_Mask04: OA2[4:1] are masked and don't care. + * @arg I2C_OA2_Mask05: OA2[5:1] are masked and don't care. + * @arg I2C_OA2_Mask06: OA2[6:1] are masked and don't care. + * @arg I2C_OA2_Mask07: OA2[7:1] are masked and don't care. + * @retval None + */ +void I2C_OwnAddress2Config(I2C_TypeDef* I2Cx, uint16_t Address, uint8_t Mask) +{ + uint32_t tmpreg = 0; + + /* Check the parameters */ + assert_param(IS_I2C_ALL_PERIPH(I2Cx)); + assert_param(IS_I2C_OWN_ADDRESS2(Address)); + assert_param(IS_I2C_OWN_ADDRESS2_MASK(Mask)); + + /* Get the old register value */ + tmpreg = I2Cx->OAR2; + + /* Reset I2Cx OA2 bit [7:1] and OA2MSK bit [1:0] */ + tmpreg &= (uint32_t)~((uint32_t)(I2C_OAR2_OA2 | I2C_OAR2_OA2MSK)); + + /* Set I2Cx SADD */ + tmpreg |= (uint32_t)(((uint32_t)Address & I2C_OAR2_OA2) | \ + (((uint32_t)Mask << 8) & I2C_OAR2_OA2MSK)) ; + + /* Store the new register value */ + I2Cx->OAR2 = tmpreg; +} + +/** + * @brief Enables or disables the I2C general call mode. + * @param I2Cx: where x can be 1 or 2 to select the I2C peripheral. + * @param NewState: new state of the I2C general call mode. + * This parameter can be: ENABLE or DISABLE. + * @retval None + */ +void I2C_GeneralCallCmd(I2C_TypeDef* I2Cx, FunctionalState NewState) +{ + /* Check the parameters */ + assert_param(IS_I2C_ALL_PERIPH(I2Cx)); + assert_param(IS_FUNCTIONAL_STATE(NewState)); + + if (NewState != DISABLE) + { + /* Enable general call mode */ + I2Cx->CR1 |= I2C_CR1_GCEN; + } + else + { + /* Disable general call mode */ + I2Cx->CR1 &= (uint32_t)~((uint32_t)I2C_CR1_GCEN); + } +} + +/** + * @brief Enables or disables the I2C slave byte control. + * @param I2Cx: where x can be 1 or 2 to select the I2C peripheral. + * @param NewState: new state of the I2C slave byte control. + * This parameter can be: ENABLE or DISABLE. + * @retval None + */ +void I2C_SlaveByteControlCmd(I2C_TypeDef* I2Cx, FunctionalState NewState) +{ + /* Check the parameters */ + assert_param(IS_I2C_ALL_PERIPH(I2Cx)); + assert_param(IS_FUNCTIONAL_STATE(NewState)); + + if (NewState != DISABLE) + { + /* Enable slave byte control */ + I2Cx->CR1 |= I2C_CR1_SBC; + } + else + { + /* Disable slave byte control */ + I2Cx->CR1 &= (uint32_t)~((uint32_t)I2C_CR1_SBC); + } +} + +/** + * @brief Configures the slave address to be transmitted after start generation. + * @param I2Cx: where x can be 1 or 2 to select the I2C peripheral. + * @param Address: specifies the slave address to be programmed. + * @note This function should be called before generating start condition. + * @retval None + */ +void I2C_SlaveAddressConfig(I2C_TypeDef* I2Cx, uint16_t Address) +{ + uint32_t tmpreg = 0; + + /* Check the parameters */ + assert_param(IS_I2C_ALL_PERIPH(I2Cx)); + assert_param(IS_I2C_SLAVE_ADDRESS(Address)); + + /* Get the old register value */ + tmpreg = I2Cx->CR2; + + /* Reset I2Cx SADD bit [9:0] */ + tmpreg &= (uint32_t)~((uint32_t)I2C_CR2_SADD); + + /* Set I2Cx SADD */ + tmpreg |= (uint32_t)((uint32_t)Address & I2C_CR2_SADD); + + /* Store the new register value */ + I2Cx->CR2 = tmpreg; +} + +/** + * @brief Enables or disables the I2C 10-bit addressing mode for the master. + * @param I2Cx: where x can be 1 or 2 to select the I2C peripheral. + * @param NewState: new state of the I2C 10-bit addressing mode. + * This parameter can be: ENABLE or DISABLE. + * @note This function should be called before generating start condition. + * @retval None + */ +void I2C_10BitAddressingModeCmd(I2C_TypeDef* I2Cx, FunctionalState NewState) +{ + /* Check the parameters */ + assert_param(IS_I2C_ALL_PERIPH(I2Cx)); + assert_param(IS_FUNCTIONAL_STATE(NewState)); + + if (NewState != DISABLE) + { + /* Enable 10-bit addressing mode */ + I2Cx->CR2 |= I2C_CR2_ADD10; + } + else + { + /* Disable 10-bit addressing mode */ + I2Cx->CR2 &= (uint32_t)~((uint32_t)I2C_CR2_ADD10); + } +} + +/** + * @} + */ + + +/** @defgroup I2C_Group2 Communications handling functions + * @brief Communications handling functions + * +@verbatim + =============================================================================== + ##### Communications handling functions ##### + =============================================================================== + [..] This section provides a set of functions that handles I2C communication. + + [..] Automatic End mode is enabled using I2C_AutoEndCmd() function. When Reload + mode is enabled via I2C_ReloadCmd() AutoEnd bit has no effect. + + [..] I2C_NumberOfBytesConfig() function set the number of bytes to be transferred, + this configuration should be done before generating start condition in master + mode. + + [..] When switching from master write operation to read operation in 10Bit addressing + mode, master can only sends the 1st 7 bits of the 10 bit address, followed by + Read direction by enabling HEADR bit using I2C_10BitAddressHeader() function. + + [..] In master mode, when transferring more than 255 bytes Reload mode should be used + to handle communication. In the first phase of transfer, Nbytes should be set to + 255. After transferring these bytes TCR flag is set and I2C_TransferHandling() + function should be called to handle remaining communication. + + [..] In master mode, when software end mode is selected when all data is transferred + TC flag is set I2C_TransferHandling() function should be called to generate STOP + or generate ReStart. + +@endverbatim + * @{ + */ + +/** + * @brief Enables or disables the I2C automatic end mode (stop condition is + * automatically sent when nbytes data are transferred). + * @param I2Cx: where x can be 1 or 2 to select the I2C peripheral. + * @param NewState: new state of the I2C automatic end mode. + * This parameter can be: ENABLE or DISABLE. + * @note This function has effect if Reload mode is disabled. + * @retval None + */ +void I2C_AutoEndCmd(I2C_TypeDef* I2Cx, FunctionalState NewState) +{ + /* Check the parameters */ + assert_param(IS_I2C_ALL_PERIPH(I2Cx)); + assert_param(IS_FUNCTIONAL_STATE(NewState)); + + if (NewState != DISABLE) + { + /* Enable Auto end mode */ + I2Cx->CR2 |= I2C_CR2_AUTOEND; + } + else + { + /* Disable Auto end mode */ + I2Cx->CR2 &= (uint32_t)~((uint32_t)I2C_CR2_AUTOEND); + } +} + +/** + * @brief Enables or disables the I2C nbytes reload mode. + * @param I2Cx: where x can be 1 or 2 to select the I2C peripheral. + * @param NewState: new state of the nbytes reload mode. + * This parameter can be: ENABLE or DISABLE. + * @retval None + */ +void I2C_ReloadCmd(I2C_TypeDef* I2Cx, FunctionalState NewState) +{ + /* Check the parameters */ + assert_param(IS_I2C_ALL_PERIPH(I2Cx)); + assert_param(IS_FUNCTIONAL_STATE(NewState)); + + if (NewState != DISABLE) + { + /* Enable Auto Reload mode */ + I2Cx->CR2 |= I2C_CR2_RELOAD; + } + else + { + /* Disable Auto Reload mode */ + I2Cx->CR2 &= (uint32_t)~((uint32_t)I2C_CR2_RELOAD); + } +} + +/** + * @brief Configures the number of bytes to be transmitted/received. + * @param I2Cx: where x can be 1 or 2 to select the I2C peripheral. + * @param Number_Bytes: specifies the number of bytes to be programmed. + * @retval None + */ +void I2C_NumberOfBytesConfig(I2C_TypeDef* I2Cx, uint8_t Number_Bytes) +{ + uint32_t tmpreg = 0; + + /* Check the parameters */ + assert_param(IS_I2C_ALL_PERIPH(I2Cx)); + + /* Get the old register value */ + tmpreg = I2Cx->CR2; + + /* Reset I2Cx Nbytes bit [7:0] */ + tmpreg &= (uint32_t)~((uint32_t)I2C_CR2_NBYTES); + + /* Set I2Cx Nbytes */ + tmpreg |= (uint32_t)(((uint32_t)Number_Bytes << 16 ) & I2C_CR2_NBYTES); + + /* Store the new register value */ + I2Cx->CR2 = tmpreg; +} + +/** + * @brief Configures the type of transfer request for the master. + * @param I2Cx: where x can be 1 or 2 to select the I2C peripheral. + * @param I2C_Direction: specifies the transfer request direction to be programmed. + * This parameter can be one of the following values: + * @arg I2C_Direction_Transmitter: Master request a write transfer + * @arg I2C_Direction_Receiver: Master request a read transfer + * @retval None + */ +void I2C_MasterRequestConfig(I2C_TypeDef* I2Cx, uint16_t I2C_Direction) +{ +/* Check the parameters */ + assert_param(IS_I2C_ALL_PERIPH(I2Cx)); + assert_param(IS_I2C_DIRECTION(I2C_Direction)); + + /* Test on the direction to set/reset the read/write bit */ + if (I2C_Direction == I2C_Direction_Transmitter) + { + /* Request a write Transfer */ + I2Cx->CR2 &= (uint32_t)~((uint32_t)I2C_CR2_RD_WRN); + } + else + { + /* Request a read Transfer */ + I2Cx->CR2 |= I2C_CR2_RD_WRN; + } +} + +/** + * @brief Generates I2Cx communication START condition. + * @param I2Cx: where x can be 1 or 2 to select the I2C peripheral. + * @param NewState: new state of the I2C START condition generation. + * This parameter can be: ENABLE or DISABLE. + * @retval None + */ +void I2C_GenerateSTART(I2C_TypeDef* I2Cx, FunctionalState NewState) +{ + /* Check the parameters */ + assert_param(IS_I2C_ALL_PERIPH(I2Cx)); + assert_param(IS_FUNCTIONAL_STATE(NewState)); + + if (NewState != DISABLE) + { + /* Generate a START condition */ + I2Cx->CR2 |= I2C_CR2_START; + } + else + { + /* Disable the START condition generation */ + I2Cx->CR2 &= (uint32_t)~((uint32_t)I2C_CR2_START); + } +} + +/** + * @brief Generates I2Cx communication STOP condition. + * @param I2Cx: where x can be 1 or 2 to select the I2C peripheral. + * @param NewState: new state of the I2C STOP condition generation. + * This parameter can be: ENABLE or DISABLE. + * @retval None + */ +void I2C_GenerateSTOP(I2C_TypeDef* I2Cx, FunctionalState NewState) +{ + /* Check the parameters */ + assert_param(IS_I2C_ALL_PERIPH(I2Cx)); + assert_param(IS_FUNCTIONAL_STATE(NewState)); + + if (NewState != DISABLE) + { + /* Generate a STOP condition */ + I2Cx->CR2 |= I2C_CR2_STOP; + } + else + { + /* Disable the STOP condition generation */ + I2Cx->CR2 &= (uint32_t)~((uint32_t)I2C_CR2_STOP); + } +} + +/** + * @brief Enables or disables the I2C 10-bit header only mode with read direction. + * @param I2Cx: where x can be 1 or 2 to select the I2C peripheral. + * @param NewState: new state of the I2C 10-bit header only mode. + * This parameter can be: ENABLE or DISABLE. + * @note This mode can be used only when switching from master transmitter mode + * to master receiver mode. + * @retval None + */ +void I2C_10BitAddressHeaderCmd(I2C_TypeDef* I2Cx, FunctionalState NewState) +{ + /* Check the parameters */ + assert_param(IS_I2C_ALL_PERIPH(I2Cx)); + assert_param(IS_FUNCTIONAL_STATE(NewState)); + + if (NewState != DISABLE) + { + /* Enable 10-bit header only mode */ + I2Cx->CR2 |= I2C_CR2_HEAD10R; + } + else + { + /* Disable 10-bit header only mode */ + I2Cx->CR2 &= (uint32_t)~((uint32_t)I2C_CR2_HEAD10R); + } +} + +/** + * @brief Generates I2C communication Acknowledge. + * @param I2Cx: where x can be 1 or 2 to select the I2C peripheral. + * @param NewState: new state of the Acknowledge. + * This parameter can be: ENABLE or DISABLE. + * @retval None + */ +void I2C_AcknowledgeConfig(I2C_TypeDef* I2Cx, FunctionalState NewState) +{ + /* Check the parameters */ + assert_param(IS_I2C_ALL_PERIPH(I2Cx)); + assert_param(IS_FUNCTIONAL_STATE(NewState)); + + if (NewState != DISABLE) + { + /* Enable ACK generation */ + I2Cx->CR2 &= (uint32_t)~((uint32_t)I2C_CR2_NACK); + } + else + { + /* Enable NACK generation */ + I2Cx->CR2 |= I2C_CR2_NACK; + } +} + +/** + * @brief Returns the I2C slave matched address . + * @param I2Cx: where x can be 1 or 2 to select the I2C peripheral. + * @retval The value of the slave matched address . + */ +uint8_t I2C_GetAddressMatched(I2C_TypeDef* I2Cx) +{ + /* Check the parameters */ + assert_param(IS_I2C_ALL_PERIPH(I2Cx)); + + /* Return the slave matched address in the SR1 register */ + return (uint8_t)(((uint32_t)I2Cx->ISR & I2C_ISR_ADDCODE) >> 16) ; +} + +/** + * @brief Returns the I2C slave received request. + * @param I2Cx: where x can be 1 or 2 to select the I2C peripheral. + * @retval The value of the received request. + */ +uint16_t I2C_GetTransferDirection(I2C_TypeDef* I2Cx) +{ + uint32_t tmpreg = 0; + uint16_t direction = 0; + + /* Check the parameters */ + assert_param(IS_I2C_ALL_PERIPH(I2Cx)); + + /* Return the slave matched address in the SR1 register */ + tmpreg = (uint32_t)(I2Cx->ISR & I2C_ISR_DIR); + + /* If write transfer is requested */ + if (tmpreg == 0) + { + /* write transfer is requested */ + direction = I2C_Direction_Transmitter; + } + else + { + /* Read transfer is requested */ + direction = I2C_Direction_Receiver; + } + return direction; +} + +/** + * @brief Handles I2Cx communication when starting transfer or during transfer (TC or TCR flag are set). + * @param I2Cx: where x can be 1 or 2 to select the I2C peripheral. + * @param Address: specifies the slave address to be programmed. + * @param Number_Bytes: specifies the number of bytes to be programmed. + * This parameter must be a value between 0 and 255. + * @param ReloadEndMode: new state of the I2C START condition generation. + * This parameter can be one of the following values: + * @arg I2C_Reload_Mode: Enable Reload mode . + * @arg I2C_AutoEnd_Mode: Enable Automatic end mode. + * @arg I2C_SoftEnd_Mode: Enable Software end mode. + * @param StartStopMode: new state of the I2C START condition generation. + * This parameter can be one of the following values: + * @arg I2C_No_StartStop: Don't Generate stop and start condition. + * @arg I2C_Generate_Stop: Generate stop condition (Number_Bytes should be set to 0). + * @arg I2C_Generate_Start_Read: Generate Restart for read request. + * @arg I2C_Generate_Start_Write: Generate Restart for write request. + * @retval None + */ +void I2C_TransferHandling(I2C_TypeDef* I2Cx, uint16_t Address, uint8_t Number_Bytes, uint32_t ReloadEndMode, uint32_t StartStopMode) +{ + uint32_t tmpreg = 0; + + /* Check the parameters */ + assert_param(IS_I2C_ALL_PERIPH(I2Cx)); + assert_param(IS_I2C_SLAVE_ADDRESS(Address)); + assert_param(IS_RELOAD_END_MODE(ReloadEndMode)); + assert_param(IS_START_STOP_MODE(StartStopMode)); + + /* Get the CR2 register value */ + tmpreg = I2Cx->CR2; + + /* clear tmpreg specific bits */ + tmpreg &= (uint32_t)~((uint32_t)(I2C_CR2_SADD | I2C_CR2_NBYTES | I2C_CR2_RELOAD | I2C_CR2_AUTOEND | I2C_CR2_RD_WRN | I2C_CR2_START | I2C_CR2_STOP)); + + /* update tmpreg */ + tmpreg |= (uint32_t)(((uint32_t)Address & I2C_CR2_SADD) | (((uint32_t)Number_Bytes << 16 ) & I2C_CR2_NBYTES) | \ + (uint32_t)ReloadEndMode | (uint32_t)StartStopMode); + + /* update CR2 register */ + I2Cx->CR2 = tmpreg; +} + +/** + * @} + */ + + +/** @defgroup I2C_Group3 SMBUS management functions + * @brief SMBUS management functions + * +@verbatim + =============================================================================== + ##### SMBUS management functions ##### + =============================================================================== + [..] This section provides a set of functions that handles SMBus communication + and timeouts detection. + + [..] The SMBus Device default address (0b1100 001) is enabled by calling I2C_Init() + function and setting I2C_Mode member of I2C_InitTypeDef() structure to + I2C_Mode_SMBusDevice. + + [..] The SMBus Host address (0b0001 000) is enabled by calling I2C_Init() + function and setting I2C_Mode member of I2C_InitTypeDef() structure to + I2C_Mode_SMBusHost. + + [..] The Alert Response Address (0b0001 100) is enabled using I2C_SMBusAlertCmd() + function. + + [..] To detect cumulative SCL stretch in master and slave mode, TIMEOUTB should be + configured (in accordance to SMBus specification) using I2C_TimeoutBConfig() + function then I2C_ExtendedClockTimeoutCmd() function should be called to enable + the detection. + + [..] SCL low timeout is detected by configuring TIMEOUTB using I2C_TimeoutBConfig() + function followed by the call of I2C_ClockTimeoutCmd(). When adding to this + procedure the call of I2C_IdleClockTimeoutCmd() function, Bus Idle condition + (both SCL and SDA high) is detected also. + +@endverbatim + * @{ + */ + +/** + * @brief Enables or disables I2C SMBus alert. + * @param I2Cx: where x can be 1 or 2 to select the I2C peripheral. + * @param NewState: new state of the I2Cx SMBus alert. + * This parameter can be: ENABLE or DISABLE. + * @retval None + */ +void I2C_SMBusAlertCmd(I2C_TypeDef* I2Cx, FunctionalState NewState) +{ + /* Check the parameters */ + assert_param(IS_I2C_ALL_PERIPH(I2Cx)); + assert_param(IS_FUNCTIONAL_STATE(NewState)); + + if (NewState != DISABLE) + { + /* Enable SMBus alert */ + I2Cx->CR1 |= I2C_CR1_ALERTEN; + } + else + { + /* Disable SMBus alert */ + I2Cx->CR1 &= (uint32_t)~((uint32_t)I2C_CR1_ALERTEN); + } +} + +/** + * @brief Enables or disables I2C Clock Timeout (SCL Timeout detection). + * @param I2Cx: where x can be 1 or 2 to select the I2C peripheral. + * @param NewState: new state of the I2Cx clock Timeout. + * This parameter can be: ENABLE or DISABLE. + * @retval None + */ +void I2C_ClockTimeoutCmd(I2C_TypeDef* I2Cx, FunctionalState NewState) +{ + /* Check the parameters */ + assert_param(IS_I2C_ALL_PERIPH(I2Cx)); + assert_param(IS_FUNCTIONAL_STATE(NewState)); + + if (NewState != DISABLE) + { + /* Enable Clock Timeout */ + I2Cx->TIMEOUTR |= I2C_TIMEOUTR_TIMOUTEN; + } + else + { + /* Disable Clock Timeout */ + I2Cx->TIMEOUTR &= (uint32_t)~((uint32_t)I2C_TIMEOUTR_TIMOUTEN); + } +} + +/** + * @brief Enables or disables I2C Extended Clock Timeout (SCL cumulative Timeout detection). + * @param I2Cx: where x can be 1 or 2 to select the I2C peripheral. + * @param NewState: new state of the I2Cx Extended clock Timeout. + * This parameter can be: ENABLE or DISABLE. + * @retval None + */ +void I2C_ExtendedClockTimeoutCmd(I2C_TypeDef* I2Cx, FunctionalState NewState) +{ + /* Check the parameters */ + assert_param(IS_I2C_ALL_PERIPH(I2Cx)); + assert_param(IS_FUNCTIONAL_STATE(NewState)); + + if (NewState != DISABLE) + { + /* Enable Clock Timeout */ + I2Cx->TIMEOUTR |= I2C_TIMEOUTR_TEXTEN; + } + else + { + /* Disable Clock Timeout */ + I2Cx->TIMEOUTR &= (uint32_t)~((uint32_t)I2C_TIMEOUTR_TEXTEN); + } +} + +/** + * @brief Enables or disables I2C Idle Clock Timeout (Bus idle SCL and SDA + * high detection). + * @param I2Cx: where x can be 1 or 2 to select the I2C peripheral. + * @param NewState: new state of the I2Cx Idle clock Timeout. + * This parameter can be: ENABLE or DISABLE. + * @retval None + */ +void I2C_IdleClockTimeoutCmd(I2C_TypeDef* I2Cx, FunctionalState NewState) +{ + /* Check the parameters */ + assert_param(IS_I2C_ALL_PERIPH(I2Cx)); + assert_param(IS_FUNCTIONAL_STATE(NewState)); + + if (NewState != DISABLE) + { + /* Enable Clock Timeout */ + I2Cx->TIMEOUTR |= I2C_TIMEOUTR_TIDLE; + } + else + { + /* Disable Clock Timeout */ + I2Cx->TIMEOUTR &= (uint32_t)~((uint32_t)I2C_TIMEOUTR_TIDLE); + } +} + +/** + * @brief Configures the I2C Bus Timeout A (SCL Timeout when TIDLE = 0 or Bus + * idle SCL and SDA high when TIDLE = 1). + * @param I2Cx: where x can be 1 or 2 to select the I2C peripheral. + * @param Timeout: specifies the TimeoutA to be programmed. + * @retval None + */ +void I2C_TimeoutAConfig(I2C_TypeDef* I2Cx, uint16_t Timeout) +{ + uint32_t tmpreg = 0; + + /* Check the parameters */ + assert_param(IS_I2C_ALL_PERIPH(I2Cx)); + assert_param(IS_I2C_TIMEOUT(Timeout)); + + /* Get the old register value */ + tmpreg = I2Cx->TIMEOUTR; + + /* Reset I2Cx TIMEOUTA bit [11:0] */ + tmpreg &= (uint32_t)~((uint32_t)I2C_TIMEOUTR_TIMEOUTA); + + /* Set I2Cx TIMEOUTA */ + tmpreg |= (uint32_t)((uint32_t)Timeout & I2C_TIMEOUTR_TIMEOUTA) ; + + /* Store the new register value */ + I2Cx->TIMEOUTR = tmpreg; +} + +/** + * @brief Configures the I2C Bus Timeout B (SCL cumulative Timeout). + * @param I2Cx: where x can be 1 or 2 to select the I2C peripheral. + * @param Timeout: specifies the TimeoutB to be programmed. + * @retval None + */ +void I2C_TimeoutBConfig(I2C_TypeDef* I2Cx, uint16_t Timeout) +{ + uint32_t tmpreg = 0; + + /* Check the parameters */ + assert_param(IS_I2C_ALL_PERIPH(I2Cx)); + assert_param(IS_I2C_TIMEOUT(Timeout)); + + /* Get the old register value */ + tmpreg = I2Cx->TIMEOUTR; + + /* Reset I2Cx TIMEOUTB bit [11:0] */ + tmpreg &= (uint32_t)~((uint32_t)I2C_TIMEOUTR_TIMEOUTB); + + /* Set I2Cx TIMEOUTB */ + tmpreg |= (uint32_t)(((uint32_t)Timeout << 16) & I2C_TIMEOUTR_TIMEOUTB) ; + + /* Store the new register value */ + I2Cx->TIMEOUTR = tmpreg; +} + +/** + * @brief Enables or disables I2C PEC calculation. + * @param I2Cx: where x can be 1 or 2 to select the I2C peripheral. + * @param NewState: new state of the I2Cx PEC calculation. + * This parameter can be: ENABLE or DISABLE. + * @retval None + */ +void I2C_CalculatePEC(I2C_TypeDef* I2Cx, FunctionalState NewState) +{ + /* Check the parameters */ + assert_param(IS_I2C_ALL_PERIPH(I2Cx)); + assert_param(IS_FUNCTIONAL_STATE(NewState)); + + if (NewState != DISABLE) + { + /* Enable PEC calculation */ + I2Cx->CR1 |= I2C_CR1_PECEN; + } + else + { + /* Disable PEC calculation */ + I2Cx->CR1 &= (uint32_t)~((uint32_t)I2C_CR1_PECEN); + } +} + +/** + * @brief Enables or disables I2C PEC transmission/reception request. + * @param I2Cx: where x can be 1 or 2 to select the I2C peripheral. + * @param NewState: new state of the I2Cx PEC request. + * This parameter can be: ENABLE or DISABLE. + * @retval None + */ +void I2C_PECRequestCmd(I2C_TypeDef* I2Cx, FunctionalState NewState) +{ + /* Check the parameters */ + assert_param(IS_I2C_ALL_PERIPH(I2Cx)); + assert_param(IS_FUNCTIONAL_STATE(NewState)); + + if (NewState != DISABLE) + { + /* Enable PEC transmission/reception request */ + I2Cx->CR1 |= I2C_CR2_PECBYTE; + } + else + { + /* Disable PEC transmission/reception request */ + I2Cx->CR1 &= (uint32_t)~((uint32_t)I2C_CR2_PECBYTE); + } +} + +/** + * @brief Returns the I2C PEC. + * @param I2Cx: where x can be 1 or 2 to select the I2C peripheral. + * @retval The value of the PEC . + */ +uint8_t I2C_GetPEC(I2C_TypeDef* I2Cx) +{ + /* Check the parameters */ + assert_param(IS_I2C_ALL_PERIPH(I2Cx)); + + /* Return the slave matched address in the SR1 register */ + return (uint8_t)((uint32_t)I2Cx->PECR & I2C_PECR_PEC); +} + +/** + * @} + */ + + +/** @defgroup I2C_Group4 I2C registers management functions + * @brief I2C registers management functions + * +@verbatim + =============================================================================== + ##### I2C registers management functions ##### + =============================================================================== + [..] This section provides a functions that allow user the management of + I2C registers. + +@endverbatim + * @{ + */ + + /** + * @brief Reads the specified I2C register and returns its value. + * @param I2Cx: where x can be 1 or 2 to select the I2C peripheral. + * @param I2C_Register: specifies the register to read. + * This parameter can be one of the following values: + * @arg I2C_Register_CR1: CR1 register. + * @arg I2C_Register_CR2: CR2 register. + * @arg I2C_Register_OAR1: OAR1 register. + * @arg I2C_Register_OAR2: OAR2 register. + * @arg I2C_Register_TIMINGR: TIMING register. + * @arg I2C_Register_TIMEOUTR: TIMEOUTR register. + * @arg I2C_Register_ISR: ISR register. + * @arg I2C_Register_ICR: ICR register. + * @arg I2C_Register_PECR: PECR register. + * @arg I2C_Register_RXDR: RXDR register. + * @arg I2C_Register_TXDR: TXDR register. + * @retval The value of the read register. + */ +uint32_t I2C_ReadRegister(I2C_TypeDef* I2Cx, uint8_t I2C_Register) +{ + __IO uint32_t tmp = 0; + + /* Check the parameters */ + assert_param(IS_I2C_ALL_PERIPH(I2Cx)); + assert_param(IS_I2C_REGISTER(I2C_Register)); + + tmp = (uint32_t)I2Cx; + tmp += I2C_Register; + + /* Return the selected register value */ + return (*(__IO uint32_t *) tmp); +} + +/** + * @} + */ + +/** @defgroup I2C_Group5 Data transfers management functions + * @brief Data transfers management functions + * +@verbatim + =============================================================================== + ##### Data transfers management functions ##### + =============================================================================== + [..] This subsection provides a set of functions allowing to manage + the I2C data transfers. + + [..] The read access of the I2C_RXDR register can be done using + the I2C_ReceiveData() function and returns the received value. + Whereas a write access to the I2C_TXDR can be done using I2C_SendData() + function and stores the written data into TXDR. +@endverbatim + * @{ + */ + +/** + * @brief Sends a data byte through the I2Cx peripheral. + * @param I2Cx: where x can be 1 or 2 to select the I2C peripheral. + * @param Data: Byte to be transmitted.. + * @retval None + */ +void I2C_SendData(I2C_TypeDef* I2Cx, uint8_t Data) +{ + /* Check the parameters */ + assert_param(IS_I2C_ALL_PERIPH(I2Cx)); + + /* Write in the DR register the data to be sent */ + I2Cx->TXDR = (uint8_t)Data; +} + +/** + * @brief Returns the most recent received data by the I2Cx peripheral. + * @param I2Cx: where x can be 1 or 2 to select the I2C peripheral. + * @retval The value of the received data. + */ +uint8_t I2C_ReceiveData(I2C_TypeDef* I2Cx) +{ + /* Check the parameters */ + assert_param(IS_I2C_ALL_PERIPH(I2Cx)); + + /* Return the data in the DR register */ + return (uint8_t)I2Cx->RXDR; +} + +/** + * @} + */ + + +/** @defgroup I2C_Group6 DMA transfers management functions + * @brief DMA transfers management functions + * +@verbatim + =============================================================================== + ##### DMA transfers management functions ##### + =============================================================================== + [..] This section provides two functions that can be used only in DMA mode. + [..] In DMA Mode, the I2C communication can be managed by 2 DMA Channel + requests: + (#) I2C_DMAReq_Tx: specifies the Tx buffer DMA transfer request. + (#) I2C_DMAReq_Rx: specifies the Rx buffer DMA transfer request. + [..] In this Mode it is advised to use the following function: + (+) I2C_DMACmd(I2C_TypeDef* I2Cx, uint32_t I2C_DMAReq, FunctionalState NewState); +@endverbatim + * @{ + */ + +/** + * @brief Enables or disables the I2C DMA interface. + * @param I2Cx: where x can be 1 or 2 to select the I2C peripheral. + * @param I2C_DMAReq: specifies the I2C DMA transfer request to be enabled or disabled. + * This parameter can be any combination of the following values: + * @arg I2C_DMAReq_Tx: Tx DMA transfer request + * @arg I2C_DMAReq_Rx: Rx DMA transfer request + * @param NewState: new state of the selected I2C DMA transfer request. + * This parameter can be: ENABLE or DISABLE. + * @retval None + */ +void I2C_DMACmd(I2C_TypeDef* I2Cx, uint32_t I2C_DMAReq, FunctionalState NewState) +{ + /* Check the parameters */ + assert_param(IS_I2C_ALL_PERIPH(I2Cx)); + assert_param(IS_FUNCTIONAL_STATE(NewState)); + assert_param(IS_I2C_DMA_REQ(I2C_DMAReq)); + + if (NewState != DISABLE) + { + /* Enable the selected I2C DMA requests */ + I2Cx->CR1 |= I2C_DMAReq; + } + else + { + /* Disable the selected I2C DMA requests */ + I2Cx->CR1 &= (uint32_t)~I2C_DMAReq; + } +} +/** + * @} + */ + + +/** @defgroup I2C_Group7 Interrupts and flags management functions + * @brief Interrupts and flags management functions + * +@verbatim + =============================================================================== + ##### Interrupts and flags management functions ##### + =============================================================================== + [..] This section provides functions allowing to configure the I2C Interrupts + sources and check or clear the flags or pending bits status. + The user should identify which mode will be used in his application to manage + the communication: Polling mode, Interrupt mode or DMA mode(refer I2C_Group6) . + + *** Polling Mode *** + ==================== + [..] In Polling Mode, the I2C communication can be managed by 15 flags: + (#) I2C_FLAG_TXE: to indicate the status of Transmit data register empty flag. + (#) I2C_FLAG_TXIS: to indicate the status of Transmit interrupt status flag . + (#) I2C_FLAG_RXNE: to indicate the status of Receive data register not empty flag. + (#) I2C_FLAG_ADDR: to indicate the status of Address matched flag (slave mode). + (#) I2C_FLAG_NACKF: to indicate the status of NACK received flag. + (#) I2C_FLAG_STOPF: to indicate the status of STOP detection flag. + (#) I2C_FLAG_TC: to indicate the status of Transfer complete flag(master mode). + (#) I2C_FLAG_TCR: to indicate the status of Transfer complete reload flag. + (#) I2C_FLAG_BERR: to indicate the status of Bus error flag. + (#) I2C_FLAG_ARLO: to indicate the status of Arbitration lost flag. + (#) I2C_FLAG_OVR: to indicate the status of Overrun/Underrun flag. + (#) I2C_FLAG_PECERR: to indicate the status of PEC error in reception flag. + (#) I2C_FLAG_TIMEOUT: to indicate the status of Timeout or Tlow detection flag. + (#) I2C_FLAG_ALERT: to indicate the status of SMBus Alert flag. + (#) I2C_FLAG_BUSY: to indicate the status of Bus busy flag. + + [..] In this Mode it is advised to use the following functions: + (+) FlagStatus I2C_GetFlagStatus(I2C_TypeDef* I2Cx, uint32_t I2C_FLAG); + (+) void I2C_ClearFlag(I2C_TypeDef* I2Cx, uint32_t I2C_FLAG); + + [..] + (@)Do not use the BUSY flag to handle each data transmission or reception.It is + better to use the TXIS and RXNE flags instead. + + *** Interrupt Mode *** + ====================== + [..] In Interrupt Mode, the I2C communication can be managed by 7 interrupt sources + and 15 pending bits: + [..] Interrupt Source: + (#) I2C_IT_ERRI: specifies the interrupt source for the Error interrupt. + (#) I2C_IT_TCI: specifies the interrupt source for the Transfer Complete interrupt. + (#) I2C_IT_STOPI: specifies the interrupt source for the Stop Detection interrupt. + (#) I2C_IT_NACKI: specifies the interrupt source for the Not Acknowledge received interrupt. + (#) I2C_IT_ADDRI: specifies the interrupt source for the Address Match interrupt. + (#) I2C_IT_RXI: specifies the interrupt source for the RX interrupt. + (#) I2C_IT_TXI: specifies the interrupt source for the TX interrupt. + + [..] Pending Bits: + (#) I2C_IT_TXIS: to indicate the status of Transmit interrupt status flag. + (#) I2C_IT_RXNE: to indicate the status of Receive data register not empty flag. + (#) I2C_IT_ADDR: to indicate the status of Address matched flag (slave mode). + (#) I2C_IT_NACKF: to indicate the status of NACK received flag. + (#) I2C_IT_STOPF: to indicate the status of STOP detection flag. + (#) I2C_IT_TC: to indicate the status of Transfer complete flag (master mode). + (#) I2C_IT_TCR: to indicate the status of Transfer complete reload flag. + (#) I2C_IT_BERR: to indicate the status of Bus error flag. + (#) I2C_IT_ARLO: to indicate the status of Arbitration lost flag. + (#) I2C_IT_OVR: to indicate the status of Overrun/Underrun flag. + (#) I2C_IT_PECERR: to indicate the status of PEC error in reception flag. + (#) I2C_IT_TIMEOUT: to indicate the status of Timeout or Tlow detection flag. + (#) I2C_IT_ALERT: to indicate the status of SMBus Alert flag. + + [..] In this Mode it is advised to use the following functions: + (+) void I2C_ClearITPendingBit(I2C_TypeDef* I2Cx, uint32_t I2C_IT); + (+) ITStatus I2C_GetITStatus(I2C_TypeDef* I2Cx, uint32_t I2C_IT); + +@endverbatim + * @{ + */ + +/** + * @brief Checks whether the specified I2C flag is set or not. + * @param I2Cx: where x can be 1 or 2 to select the I2C peripheral. + * @param I2C_FLAG: specifies the flag to check. + * This parameter can be one of the following values: + * @arg I2C_FLAG_TXE: Transmit data register empty + * @arg I2C_FLAG_TXIS: Transmit interrupt status + * @arg I2C_FLAG_RXNE: Receive data register not empty + * @arg I2C_FLAG_ADDR: Address matched (slave mode) + * @arg I2C_FLAG_NACKF: NACK received flag + * @arg I2C_FLAG_STOPF: STOP detection flag + * @arg I2C_FLAG_TC: Transfer complete (master mode) + * @arg I2C_FLAG_TCR: Transfer complete reload + * @arg I2C_FLAG_BERR: Bus error + * @arg I2C_FLAG_ARLO: Arbitration lost + * @arg I2C_FLAG_OVR: Overrun/Underrun + * @arg I2C_FLAG_PECERR: PEC error in reception + * @arg I2C_FLAG_TIMEOUT: Timeout or Tlow detection flag + * @arg I2C_FLAG_ALERT: SMBus Alert + * @arg I2C_FLAG_BUSY: Bus busy + * @retval The new state of I2C_FLAG (SET or RESET). + */ +FlagStatus I2C_GetFlagStatus(I2C_TypeDef* I2Cx, uint32_t I2C_FLAG) +{ + uint32_t tmpreg = 0; + FlagStatus bitstatus = RESET; + + /* Check the parameters */ + assert_param(IS_I2C_ALL_PERIPH(I2Cx)); + assert_param(IS_I2C_GET_FLAG(I2C_FLAG)); + + /* Get the ISR register value */ + tmpreg = I2Cx->ISR; + + /* Get flag status */ + tmpreg &= I2C_FLAG; + + if(tmpreg != 0) + { + /* I2C_FLAG is set */ + bitstatus = SET; + } + else + { + /* I2C_FLAG is reset */ + bitstatus = RESET; + } + return bitstatus; +} + +/** + * @brief Clears the I2Cx's pending flags. + * @param I2Cx: where x can be 1 or 2 to select the I2C peripheral. + * @param I2C_FLAG: specifies the flag to clear. + * This parameter can be any combination of the following values: + * @arg I2C_FLAG_ADDR: Address matched (slave mode) + * @arg I2C_FLAG_NACKF: NACK received flag + * @arg I2C_FLAG_STOPF: STOP detection flag + * @arg I2C_FLAG_BERR: Bus error + * @arg I2C_FLAG_ARLO: Arbitration lost + * @arg I2C_FLAG_OVR: Overrun/Underrun + * @arg I2C_FLAG_PECERR: PEC error in reception + * @arg I2C_FLAG_TIMEOUT: Timeout or Tlow detection flag + * @arg I2C_FLAG_ALERT: SMBus Alert + * @retval The new state of I2C_FLAG (SET or RESET). + */ +void I2C_ClearFlag(I2C_TypeDef* I2Cx, uint32_t I2C_FLAG) +{ + /* Check the parameters */ + assert_param(IS_I2C_ALL_PERIPH(I2Cx)); + assert_param(IS_I2C_CLEAR_FLAG(I2C_FLAG)); + + /* Clear the selected flag */ + I2Cx->ICR = I2C_FLAG; + } + +/** + * @brief Checks whether the specified I2C interrupt has occurred or not. + * @param I2Cx: where x can be 1 or 2 to select the I2C peripheral. + * @param I2C_IT: specifies the interrupt source to check. + * This parameter can be one of the following values: + * @arg I2C_IT_TXIS: Transmit interrupt status + * @arg I2C_IT_RXNE: Receive data register not empty + * @arg I2C_IT_ADDR: Address matched (slave mode) + * @arg I2C_IT_NACKF: NACK received flag + * @arg I2C_IT_STOPF: STOP detection flag + * @arg I2C_IT_TC: Transfer complete (master mode) + * @arg I2C_IT_TCR: Transfer complete reload + * @arg I2C_IT_BERR: Bus error + * @arg I2C_IT_ARLO: Arbitration lost + * @arg I2C_IT_OVR: Overrun/Underrun + * @arg I2C_IT_PECERR: PEC error in reception + * @arg I2C_IT_TIMEOUT: Timeout or Tlow detection flag + * @arg I2C_IT_ALERT: SMBus Alert + * @retval The new state of I2C_IT (SET or RESET). + */ +ITStatus I2C_GetITStatus(I2C_TypeDef* I2Cx, uint32_t I2C_IT) +{ + uint32_t tmpreg = 0; + ITStatus bitstatus = RESET; + uint32_t enablestatus = 0; + + /* Check the parameters */ + assert_param(IS_I2C_ALL_PERIPH(I2Cx)); + assert_param(IS_I2C_GET_IT(I2C_IT)); + + /* Check if the interrupt source is enabled or not */ + /* If Error interrupt */ + if((uint32_t)(I2C_IT & ERROR_IT_MASK)) + { + enablestatus = (uint32_t)((I2C_CR1_ERRIE) & (I2Cx->CR1)); + } + /* If TC interrupt */ + else if((uint32_t)(I2C_IT & TC_IT_MASK)) + { + enablestatus = (uint32_t)((I2C_CR1_TCIE) & (I2Cx->CR1)); + } + else + { + enablestatus = (uint32_t)((I2C_IT) & (I2Cx->CR1)); + } + + /* Get the ISR register value */ + tmpreg = I2Cx->ISR; + + /* Get flag status */ + tmpreg &= I2C_IT; + + /* Check the status of the specified I2C flag */ + if((tmpreg != RESET) && enablestatus) + { + /* I2C_IT is set */ + bitstatus = SET; + } + else + { + /* I2C_IT is reset */ + bitstatus = RESET; + } + + /* Return the I2C_IT status */ + return bitstatus; +} + +/** + * @brief Clears the I2Cx's interrupt pending bits. + * @param I2Cx: where x can be 1 or 2 to select the I2C peripheral. + * @param I2C_IT: specifies the interrupt pending bit to clear. + * This parameter can be any combination of the following values: + * @arg I2C_IT_ADDR: Address matched (slave mode) + * @arg I2C_IT_NACKF: NACK received flag + * @arg I2C_IT_STOPF: STOP detection flag + * @arg I2C_IT_BERR: Bus error + * @arg I2C_IT_ARLO: Arbitration lost + * @arg I2C_IT_OVR: Overrun/Underrun + * @arg I2C_IT_PECERR: PEC error in reception + * @arg I2C_IT_TIMEOUT: Timeout or Tlow detection flag + * @arg I2C_IT_ALERT: SMBus Alert + * @retval The new state of I2C_IT (SET or RESET). + */ +void I2C_ClearITPendingBit(I2C_TypeDef* I2Cx, uint32_t I2C_IT) +{ + /* Check the parameters */ + assert_param(IS_I2C_ALL_PERIPH(I2Cx)); + assert_param(IS_I2C_CLEAR_IT(I2C_IT)); + + /* Clear the selected flag */ + I2Cx->ICR = I2C_IT; +} + +/** + * @} + */ + +/** + * @} + */ + +/** + * @} + */ + +/** + * @} + */ + +/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/ |