diff options
Diffstat (limited to 'thirdparty/STM32_USB-FS-Device_Lib_V4.0.0/Libraries/STM32F30x_StdPeriph_Driver/src/stm32f30x_pwr.c')
| -rw-r--r-- | thirdparty/STM32_USB-FS-Device_Lib_V4.0.0/Libraries/STM32F30x_StdPeriph_Driver/src/stm32f30x_pwr.c | 538 |
1 files changed, 538 insertions, 0 deletions
diff --git a/thirdparty/STM32_USB-FS-Device_Lib_V4.0.0/Libraries/STM32F30x_StdPeriph_Driver/src/stm32f30x_pwr.c b/thirdparty/STM32_USB-FS-Device_Lib_V4.0.0/Libraries/STM32F30x_StdPeriph_Driver/src/stm32f30x_pwr.c new file mode 100644 index 0000000..0a0e26a --- /dev/null +++ b/thirdparty/STM32_USB-FS-Device_Lib_V4.0.0/Libraries/STM32F30x_StdPeriph_Driver/src/stm32f30x_pwr.c @@ -0,0 +1,538 @@ +/** + ****************************************************************************** + * @file stm32f30x_pwr.c + * @author MCD Application Team + * @version V1.0.1 + * @date 23-October-2012 + * @brief This file provides firmware functions to manage the following + * functionalities of the Power Controller (PWR) peripheral: + * + Backup Domain Access + * + PVD configuration + * + WakeUp pins configuration + * + Low Power modes configuration + * + Flags management + * + ****************************************************************************** + * @attention + * + * <h2><center>© COPYRIGHT 2012 STMicroelectronics</center></h2> + * + * Licensed under MCD-ST Liberty SW License Agreement V2, (the "License"); + * You may not use this file except in compliance with the License. + * You may obtain a copy of the License at: + * + * http://www.st.com/software_license_agreement_liberty_v2 + * + * Unless required by applicable law or agreed to in writing, software + * distributed under the License is distributed on an "AS IS" BASIS, + * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. + * See the License for the specific language governing permissions and + * limitations under the License. + * + ****************************************************************************** + */ + +/* Includes ------------------------------------------------------------------*/ +#include "stm32f30x_pwr.h" +#include "stm32f30x_rcc.h" + +/** @addtogroup STM32F30x_StdPeriph_Driver + * @{ + */ + +/** @defgroup PWR + * @brief PWR driver modules + * @{ + */ + +/* Private typedef -----------------------------------------------------------*/ +/* Private define ------------------------------------------------------------*/ +/* --------- PWR registers bit address in the alias region ---------- */ +#define PWR_OFFSET (PWR_BASE - PERIPH_BASE) + +/* --- CR Register ---*/ + +/* Alias word address of DBP bit */ +#define CR_OFFSET (PWR_OFFSET + 0x00) +#define DBP_BitNumber 0x08 +#define CR_DBP_BB (PERIPH_BB_BASE + (CR_OFFSET * 32) + (DBP_BitNumber * 4)) + +/* Alias word address of PVDE bit */ +#define PVDE_BitNumber 0x04 +#define CR_PVDE_BB (PERIPH_BB_BASE + (CR_OFFSET * 32) + (PVDE_BitNumber * 4)) + +/* ------------------ PWR registers bit mask ------------------------ */ + +/* CR register bit mask */ +#define CR_DS_MASK ((uint32_t)0xFFFFFFFC) +#define CR_PLS_MASK ((uint32_t)0xFFFFFF1F) + +/* Private macro -------------------------------------------------------------*/ +/* Private variables ---------------------------------------------------------*/ +/* Private function prototypes -----------------------------------------------*/ +/* Private functions ---------------------------------------------------------*/ + +/** @defgroup PWR_Private_Functions + * @{ + */ + +/** @defgroup PWR_Group1 Backup Domain Access function + * @brief Backup Domain Access function + * +@verbatim + ============================================================================== + ##### Backup Domain Access function ##### + ============================================================================== + + [..] After reset, the Backup Domain Registers (RCC BDCR Register, RTC registers + and RTC backup registers) are protected against possible stray write accesses. + [..] To enable access to Backup domain use the PWR_BackupAccessCmd(ENABLE) function. + +@endverbatim + * @{ + */ + +/** + * @brief Deinitializes the PWR peripheral registers to their default reset values. + * @param None + * @retval None + */ +void PWR_DeInit(void) +{ + RCC_APB1PeriphResetCmd(RCC_APB1Periph_PWR, ENABLE); + RCC_APB1PeriphResetCmd(RCC_APB1Periph_PWR, DISABLE); +} + +/** + * @brief Enables or disables access to the RTC and backup registers. + * @note If the HSE divided by 32 is used as the RTC clock, the + * Backup Domain Access should be kept enabled. + * @param NewState: new state of the access to the RTC and backup registers. + * This parameter can be: ENABLE or DISABLE. + * @retval None + */ +void PWR_BackupAccessCmd(FunctionalState NewState) +{ + /* Check the parameters */ + assert_param(IS_FUNCTIONAL_STATE(NewState)); + *(__IO uint32_t *) CR_DBP_BB = (uint32_t)NewState; +} + +/** + * @} + */ + +/** @defgroup PWR_Group2 PVD configuration functions + * @brief PVD configuration functions + * +@verbatim + =============================================================================== + ##### PVD configuration functions ##### + ============================================================================== + [..] + (+) The PVD is used to monitor the VDD power supply by comparing it to a threshold + selected by the PVD Level (PLS[2:0] bits in the PWR_CR). + (+) A PVDO flag is available to indicate if VDD/VDDA is higher or lower than the + PVD threshold. This event is internally connected to the EXTI line16 + and can generate an interrupt if enabled through the EXTI registers. + (+) The PVD is stopped in Standby mode. + +@endverbatim + * @{ + */ + +/** + * @brief Configures the voltage threshold detected by the Power Voltage Detector(PVD). + * @param PWR_PVDLevel: specifies the PVD detection level + * This parameter can be one of the following values: + * @arg PWR_PVDLevel_0: PVD detection level set to 2.18V + * @arg PWR_PVDLevel_1: PVD detection level set to 2.28V + * @arg PWR_PVDLevel_2: PVD detection level set to 2.38V + * @arg PWR_PVDLevel_3: PVD detection level set to 2.48V + * @arg PWR_PVDLevel_4: PVD detection level set to 2.58V + * @arg PWR_PVDLevel_5: PVD detection level set to 2.68V + * @arg PWR_PVDLevel_6: PVD detection level set to 2.78V + * @arg PWR_PVDLevel_7: PVD detection level set to 2.88V + * @retval None + */ +void PWR_PVDLevelConfig(uint32_t PWR_PVDLevel) +{ + uint32_t tmpreg = 0; + + /* Check the parameters */ + assert_param(IS_PWR_PVD_LEVEL(PWR_PVDLevel)); + + tmpreg = PWR->CR; + + /* Clear PLS[7:5] bits */ + tmpreg &= CR_PLS_MASK; + + /* Set PLS[7:5] bits according to PWR_PVDLevel value */ + tmpreg |= PWR_PVDLevel; + + /* Store the new value */ + PWR->CR = tmpreg; +} + +/** + * @brief Enables or disables the Power Voltage Detector(PVD). + * @param NewState: new state of the PVD. + * This parameter can be: ENABLE or DISABLE. + * @retval None + */ +void PWR_PVDCmd(FunctionalState NewState) +{ + /* Check the parameters */ + assert_param(IS_FUNCTIONAL_STATE(NewState)); + *(__IO uint32_t *) CR_PVDE_BB = (uint32_t)NewState; +} + +/** + * @} + */ + +/** @defgroup PWR_Group3 WakeUp pins configuration functions + * @brief WakeUp pins configuration functions + * +@verbatim + =============================================================================== + ##### WakeUp pins configuration functions ##### + =============================================================================== + [..] + (+) WakeUp pins are used to wakeup the system from Standby mode. These pins are + forced in input pull down configuration and are active on rising edges. + (+) There are three WakeUp pins: WakeUp Pin 1 on PA.00, WakeUp Pin 2 on PC.13 and + WakeUp Pin 3 on PE.06. + +@endverbatim + * @{ + */ + +/** + * @brief Enables or disables the WakeUp Pin functionality. + * @param PWR_WakeUpPin: specifies the WakeUpPin. + * This parameter can be: PWR_WakeUpPin_1, PWR_WakeUpPin_2 or PWR_WakeUpPin_3. + * @param NewState: new state of the WakeUp Pin functionality. + * This parameter can be: ENABLE or DISABLE. + * @retval None + */ +void PWR_WakeUpPinCmd(uint32_t PWR_WakeUpPin, FunctionalState NewState) +{ + /* Check the parameters */ + assert_param(IS_PWR_WAKEUP_PIN(PWR_WakeUpPin)); + assert_param(IS_FUNCTIONAL_STATE(NewState)); + + if (NewState != DISABLE) + { + /* Enable the EWUPx pin */ + PWR->CSR |= PWR_WakeUpPin; + } + else + { + /* Disable the EWUPx pin */ + PWR->CSR &= ~PWR_WakeUpPin; + } +} + +/** + * @} + */ + + +/** @defgroup PWR_Group4 Low Power modes configuration functions + * @brief Low Power modes configuration functions + * +@verbatim + =============================================================================== + ##### Low Power modes configuration functions ##### + ============================================================================== + + [..] The devices feature three low-power modes: + (+) Sleep mode: Cortex-M4 core stopped, peripherals kept running. + (+) Stop mode: all clocks are stopped, regulator running, regulator in low power mode + (+) Standby mode: VCORE domain powered off + + *** Sleep mode *** + ================== + [..] + (+) Entry: + (++) The Sleep mode is entered by executing the WFE() or WFI() instructions. + (+) Exit: + (++) Any peripheral interrupt acknowledged by the nested vectored interrupt + controller (NVIC) can wake up the device from Sleep mode. + + *** Stop mode *** + ================= + [..] In Stop mode, all clocks in the VCORE domain are stopped, the PLL, the HSI, + and the HSE RC oscillators are disabled. Internal SRAM and register + contents are preserved. + The voltage regulator can be configured either in normal or low-power mode. + + (+) Entry: + (++) The Stop mode is entered using the PWR_EnterSTOPMode(PWR_Regulator_LowPower,) + function with regulator in LowPower or with Regulator ON. + (+) Exit: + (++) Any EXTI Line (Internal or External) configured in Interrupt/Event mode + or any internal IPs (I2C or UASRT) wakeup event. + + *** Standby mode *** + ==================== + [..] The Standby mode allows to achieve the lowest power consumption. It is based + on the Cortex-M4 deepsleep mode, with the voltage regulator disabled. + The VCORE domain is consequently powered off. The PLL, the HSI, and the HSE + oscillator are also switched off. SRAM and register + contents are lost except for the Backup domain (RTC registers, RTC backup + registers and Standby circuitry). + + [..] The voltage regulator is OFF. + + (+) Entry: + (++) The Standby mode is entered using the PWR_EnterSTANDBYMode() function. + (+) Exit: + (++) WKUP pin rising edge, RTC alarm (Alarm A and Alarm B), RTC wakeup, + tamper event, time-stamp event, external reset in NRST pin, IWDG reset. + + *** Auto-wakeup (AWU) from low-power mode *** + ============================================= + [..] The MCU can be woken up from low-power mode by an RTC Alarm event, a tamper + event, a time-stamp event, or a comparator event, without depending on an + external interrupt (Auto-wakeup mode). + + (+) RTC auto-wakeup (AWU) from the Stop mode + (++) To wake up from the Stop mode with an RTC alarm event, it is necessary to: + (+++) Configure the EXTI Line 17 to be sensitive to rising edges (Interrupt + or Event modes) using the EXTI_Init() function. + (+++) Enable the RTC Alarm Interrupt using the RTC_ITConfig() function + (+++) Configure the RTC to generate the RTC alarm using the RTC_SetAlarm() + and RTC_AlarmCmd() functions. + (++) To wake up from the Stop mode with an RTC Tamper or time stamp event, it + is necessary to: + (+++) Configure the EXTI Line 19 to be sensitive to rising edges (Interrupt + or Event modes) using the EXTI_Init() function. + (+++) Enable the RTC Tamper or time stamp Interrupt using the RTC_ITConfig() + function. + (+++) Configure the RTC to detect the tamper or time stamp event using the + RTC_TimeStampConfig(), RTC_TamperTriggerConfig() and RTC_TamperCmd() + functions. + + (+) RTC auto-wakeup (AWU) from the Standby mode + (++) To wake up from the Standby mode with an RTC alarm event, it is necessary to: + (+++) Enable the RTC Alarm Interrupt using the RTC_ITConfig() function. + (+++) Configure the RTC to generate the RTC alarm using the RTC_SetAlarm() + and RTC_AlarmCmd() functions. + (++) To wake up from the Standby mode with an RTC Tamper or time stamp event, it + is necessary to: + (+++) Enable the RTC Tamper or time stamp Interrupt using the RTC_ITConfig() + function. + (+++) Configure the RTC to detect the tamper or time stamp event using the + RTC_TimeStampConfig(), RTC_TamperTriggerConfig() and RTC_TamperCmd() + functions. + + (+) Comparator auto-wakeup (AWU) from the Stop mode + (++) To wake up from the Stop mode with a comparator wakeup event, it is necessary to: + (+++) Configure the correspondant comparator EXTI Line to be sensitive to + the selected edges (falling, rising or falling and rising) + (Interrupt or Event modes) using the EXTI_Init() function. + (+++) Configure the comparator to generate the event. + +@endverbatim + * @{ + */ + +/** + * @brief Enters Sleep mode. + * @note In Sleep mode, all I/O pins keep the same state as in Run mode. + * @param PWR_SLEEPEntry: specifies if SLEEP mode in entered with WFI or WFE instruction. + * This parameter can be one of the following values: + * @arg PWR_SLEEPEntry_WFI: enter SLEEP mode with WFI instruction + * @arg PWR_SLEEPEntry_WFE: enter SLEEP mode with WFE instruction + * @retval None + */ +void PWR_EnterSleepMode(uint8_t PWR_SLEEPEntry) +{ + /* Check the parameters */ + assert_param(IS_PWR_SLEEP_ENTRY(PWR_SLEEPEntry)); + + /* Clear SLEEPDEEP bit of Cortex System Control Register */ + SCB->SCR &= (uint32_t)~((uint32_t)SCB_SCR_SLEEPDEEP_Msk); + + /* Select SLEEP mode entry -------------------------------------------------*/ + if(PWR_SLEEPEntry == PWR_SLEEPEntry_WFI) + { + /* Request Wait For Interrupt */ + __WFI(); + } + else + { + /* Request Wait For Event */ + __WFE(); + } +} + +/** + * @brief Enters STOP mode. + * @note In Stop mode, all I/O pins keep the same state as in Run mode. + * @note When exiting Stop mode by issuing an interrupt or a wakeup event, + * the HSI RC oscillator is selected as system clock. + * @note When the voltage regulator operates in low power mode, an additional + * startup delay is incurred when waking up from Stop mode. + * By keeping the internal regulator ON during Stop mode, the consumption + * is higher although the startup time is reduced. + * @param PWR_Regulator: specifies the regulator state in STOP mode. + * This parameter can be one of the following values: + * @arg PWR_Regulator_ON: STOP mode with regulator ON + * @arg PWR_Regulator_LowPower: STOP mode with regulator in low power mode + * @param PWR_STOPEntry: specifies if STOP mode in entered with WFI or WFE instruction. + * This parameter can be one of the following values: + * @arg PWR_STOPEntry_WFI: enter STOP mode with WFI instruction + * @arg PWR_STOPEntry_WFE: enter STOP mode with WFE instruction + * @retval None + */ +void PWR_EnterSTOPMode(uint32_t PWR_Regulator, uint8_t PWR_STOPEntry) +{ + uint32_t tmpreg = 0; + + /* Check the parameters */ + assert_param(IS_PWR_REGULATOR(PWR_Regulator)); + assert_param(IS_PWR_STOP_ENTRY(PWR_STOPEntry)); + + /* Select the regulator state in STOP mode ---------------------------------*/ + tmpreg = PWR->CR; + /* Clear PDDS and LPDSR bits */ + tmpreg &= CR_DS_MASK; + + /* Set LPDSR bit according to PWR_Regulator value */ + tmpreg |= PWR_Regulator; + + /* Store the new value */ + PWR->CR = tmpreg; + + /* Set SLEEPDEEP bit of Cortex System Control Register */ + SCB->SCR |= SCB_SCR_SLEEPDEEP_Msk; + + /* Select STOP mode entry --------------------------------------------------*/ + if(PWR_STOPEntry == PWR_STOPEntry_WFI) + { + /* Request Wait For Interrupt */ + __WFI(); + } + else + { + /* Request Wait For Event */ + __WFE(); + } + /* Reset SLEEPDEEP bit of Cortex System Control Register */ + SCB->SCR &= (uint32_t)~((uint32_t)SCB_SCR_SLEEPDEEP_Msk); +} + +/** + * @brief Enters STANDBY mode. + * @note In Standby mode, all I/O pins are high impedance except for: + * @note Reset pad (still available) + * @note RTC_AF1 pin (PC13) if configured for Wakeup pin 2 (WKUP2), tamper, + * time-stamp, RTC Alarm out, or RTC clock calibration out. + * @note WKUP pin 1 (PA0) and WKUP pin 3 (PE6), if enabled. + * @param None + * @retval None + */ +void PWR_EnterSTANDBYMode(void) +{ + /* Clear Wakeup flag */ + PWR->CR |= PWR_CR_CWUF; + + /* Select STANDBY mode */ + PWR->CR |= PWR_CR_PDDS; + + /* Set SLEEPDEEP bit of Cortex System Control Register */ + SCB->SCR |= SCB_SCR_SLEEPDEEP_Msk; + +/* This option is used to ensure that store operations are completed */ +#if defined ( __CC_ARM ) + __force_stores(); +#endif + /* Request Wait For Interrupt */ + __WFI(); +} + +/** + * @} + */ + +/** @defgroup PWR_Group5 Flags management functions + * @brief Flags management functions + * +@verbatim + =============================================================================== + ##### Flags management functions ##### + =============================================================================== + +@endverbatim + * @{ + */ + +/** + * @brief Checks whether the specified PWR flag is set or not. + * @param PWR_FLAG: specifies the flag to check. + * This parameter can be one of the following values: + * @arg PWR_FLAG_WU: Wake Up flag. This flag indicates that a wakeup event + * was received from the WKUP pin or from the RTC alarm (Alarm A or Alarm B), + * RTC Tamper event, RTC TimeStamp event or RTC Wakeup. + * @arg PWR_FLAG_SB: StandBy flag. This flag indicates that the system was + * resumed from StandBy mode. + * @arg PWR_FLAG_PVDO: PVD Output. This flag is valid only if PVD is enabled + * by the PWR_PVDCmd() function. + * @arg PWR_FLAG_VREFINTRDY: Internal Voltage Reference Ready flag. This + * flag indicates the state of the internal voltage reference, VREFINT. + * @retval The new state of PWR_FLAG (SET or RESET). + */ +FlagStatus PWR_GetFlagStatus(uint32_t PWR_FLAG) +{ + FlagStatus bitstatus = RESET; + /* Check the parameters */ + assert_param(IS_PWR_GET_FLAG(PWR_FLAG)); + + if ((PWR->CSR & PWR_FLAG) != (uint32_t)RESET) + { + bitstatus = SET; + } + else + { + bitstatus = RESET; + } + /* Return the flag status */ + return bitstatus; +} + +/** + * @brief Clears the PWR's pending flags. + * @param PWR_FLAG: specifies the flag to clear. + * This parameter can be one of the following values: + * @arg PWR_FLAG_WU: Wake Up flag + * @arg PWR_FLAG_SB: StandBy flag + * @retval None + */ +void PWR_ClearFlag(uint32_t PWR_FLAG) +{ + /* Check the parameters */ + assert_param(IS_PWR_CLEAR_FLAG(PWR_FLAG)); + + PWR->CR |= PWR_FLAG << 2; +} + +/** + * @} + */ + +/** + * @} + */ + +/** + * @} + */ + +/** + * @} + */ + +/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/ |